| |
|
 |
Maxim Integrated Products, Inc.
|
| Part No. |
MAX7033EVKIT-433
|
| OCR Text |
... E4420B or equivalent) Optional ammeter for measuring supply current Oscilloscope
2) Connect the RF signal generator to the RF_IN SMA connector. Do not turn on the generator output. Set the generator for an output frequency of 315MHz (or... |
| Description |
Evaluation Kit
|
| File Size |
210.85K /
7 Page |
 View
it Online |
Download Datasheet
|
| |
|
|
Maxim Integrated Products, Inc.
|
| Part No. |
MAX1479EVKIT-433 MAX1479EVKIT-315
|
| OCR Text |
...h as the Agilent 8562E Optional ammeter for measuring supply current Power meter such as the Agilent EPM-441A
This section provides a step-by-step guide to operating the EV kit and testing the device's functionality. Do not turn on the D... |
| Description |
Evaluation Kit
|
| File Size |
116.90K /
6 Page |
View
it Online |
Download Datasheet |
| |
|
|
Maxim
|
| Part No. |
MAX9994EVKIT
|
| OCR Text |
...upply to the EV kit (through an ammeter, if desired). Enable the supply. Readjust the supply to get +5.0V at the EV kit. There will be a voltage drop across the ammeter when the mixer is drawing current. 10) Select LO1 by connecting LOSEL (... |
| Description |
Evaluation Kit for the MAX9994
From old datasheet system
|
| File Size |
256.85K /
8 Page |
View
it Online |
Download Datasheet |
| |
|
|
Maxim
|
| Part No. |
MAX9996EVKIT
|
| OCR Text |
...upply to the EV kit (through an ammeter, if desired). Enable the supply. Readjust the supply to get +5.0V at the EV kit. There will be a voltage drop across the ammeter when the mixer is drawing current. 10) Select LO1 by connecting LOSEL (... |
| Description |
Evaluation Kit for the MAX9996
From old datasheet system
|
| File Size |
199.20K /
8 Page |
View
it Online |
Download Datasheet |
| |
|
|
Maxim Integrated Products, Inc.
|
| Part No. |
MAX1473EVKIT-433 MAX1473EVKIT-315
|
| OCR Text |
...4420B or equivalent) * Optional ammeter for measuring supply current * Oscilloscope
AM-modulated square wave (or a 2kHz pulse-modulated signal). 3) Connect the oscilloscope to test point TP3. 4) Turn on the DC supply. The supply current ... |
| Description |
Evaluation Kit 评估
|
| File Size |
288.82K /
6 Page |
View
it Online |
Download Datasheet |
| |
|
|
ONSEMI[ON Semiconductor]
|
| Part No. |
AND8019D AND8019
|
| OCR Text |
...ector should be connected to an ammeter in the high line, and then to a set of load resistors. The 12 W and 10 W resistors should be rated at 10 watts, and the 55 W at 2.0 watts. Any lab scope with at least a 20 MHz bandwidth will be adequa... |
| Description |
Offline Converter Provides 5.0 Volt/ 1.0 Amp Output for Small Electronic Equipment
Offline Converter Provides 5.0 Volt 1.0 Amp Output for Small Electronic Equipment
Offline Converter Provides 5.0 Volt, 1.0 Amp Output for Small Electronic Equipment
|
| File Size |
213.72K /
12 Page |
View
it Online |
Download Datasheet |
| |
|
|
Unity Opto Technology Co., Ltd.
UOT[Unity Opto Technology]
|
| Part No. |
MOF-R3C3
|
| OCR Text |
...D
A
GND
VOUT
D
5V
ammeter VCC
Input
13.2 Mbps NRZ, Duty 50% or 6.6 Mbps biphase mark PRBS signal Notes (1)Vcc=5.0V (State of operating) (2)To bundle up the standard fiber optic cable, make it into a loop with the diamete... |
| Description |
Fiber Optic Receiver 光纤接收
|
| File Size |
347.95K /
4 Page |
View
it Online |
Download Datasheet |
| |
|
|
MITSUMI[Mitsumi Electronics, Corp.]
|
| Part No. |
MM1188
|
| OCR Text |
...easuring Procedure Connect a DC ammeter to the VCC pin and measure. The ammeter is shorted for use in subsequent measurements. Input a 1.0VP-P, 100kHz sine wave to SG, and obtain Gv from the following formula given TP1 voltage as V1 and TP3... |
| Description |
From old datasheet system
3-Input 1-Output Video Switch (with Y-C mix) Monolithic IC
|
| File Size |
116.49K /
5 Page |
View
it Online |
Download Datasheet |
|
Price and Availability
|
