Part Number Hot Search : 
222M35V1 SRGP10Q SM6527 91600 E105M 4415GH LM766 5C6V2
Product Description
Full Text Search
 

To Download K4S561633C-N Datasheet File

  If you can't view the Datasheet, Please click here to try to view without PDF Reader .  
 
 


  Datasheet File OCR Text:
 K4S561633C-R(B)L/N/P
CMOS SDRAM
16Mx16 SDRAM 54CSP
(VDD/VDDQ 3.0V/3.0V or 3.3V/3.3V)
Revision 1.4 December 2002
Rev. 1.4 Dec. 2002
K4S561633C-R(B)L/N/P
4M x 16Bit x 4 Banks Synchronous DRAM in 54CSP
FEATURES
* 3.0V & 3.3V power supply. * LVCMOS compatible with multiplexed address. * Four banks operation. * MRS cycle with address key programs. -. CAS latency (1 & 2 & 3). -. Burst length (1, 2, 4, 8 & Full page). -. Burst type (Sequential & Interleave). * All inputs are sampled at the positive going edge of the system clock. * Burst read single-bit write operation. * DQM for masking * Auto refresh. * 64ms refresh period (8K cycle). * Commercial Temperature Operation (-25C ~ 70 C). Extended Temperature Operation ( -25C ~ 85C). Inderstrial Temperature Operation ( -40C ~ 85C). * 54balls CSP (-RXXX - Pb, -BXXX - Pb Free)
CMOS SDRAM
GENERAL DESCRIPTION
The K4S561633C is 268,435,456 bits synchronous high data rate Dynamic RAM organized as 4 x 4,196,304 words by 16 bits, fabricated with SAMSUNG's high performance CMOS technology. Synchronous design allows precise cycle control with the use of system clock and I/O transactions are possible on every clock cycle. Range of operating frequencies, programmable burst length and programmable latencies allow the same device to be useful for a variety of high bandwidth, high performance memory system applications.
ORDERING INFORMATION
Part No. K4S561633C-R(B)L/N/P75 K4S561633C-R(B)L/N/P1H K4S561633C-R(B)L/N/P1L Max Freq. 133MHz(CL=3) 105MHz(CL=2) 105MHz(CL=2) 105MHz(CL=3)*1 LVCMOS Interface Package 54 CSP Pb (Pb Free)
FUNCTIONAL BLOCK DIAGRAM
-R(B)L ; Low Power, Operating Temp : -25C ~ 70C. -R(B)N ; Low Power, Operating Temp : -25C ~ 85 C. -R(B)P : Low Power, Operating Temp : -40C ~ 85C. Note : 1. In case of 40MHz Frequency, CL1 can be supported.
I/O Control
LWE
Data Input Register
LDQM
Bank Select 4M x 16 Sense AMP 4M x 16 4M x 16 4M x 16
Refresh Counter
Output Buffer
Row Decoder
Row Buffer
DQi
Address Register
CLK ADD
Column Decoder Col. Buffer Latency & Burst Length
LRAS
LCBR
LCKE LRAS LCBR LWE LCAS
Programming Register LWCBR LDQM
Timing Register
CLK
CKE
CS
RAS
CAS
WE
L(U)DQM
* Samsung Electronics reserves the right to change products or specification without notice.
Rev. 1.4 Dec. 2002
K4S561633C-R(B)L/N/P
Package Dimension and Pin Configuration
< Bottom View*1 >
E1
CMOS SDRAM
< Top View*2 >
54Ball(6x9) CSP 1 2 DQ15 DQ13 DQ11 DQ9 NC CLK A11 A7 A5 3 VSSQ VDDQ VSSQ VDDQ VSS CKE A9 A6 A4 7 VDDQ VSSQ VDDQ VSSQ VD D CAS BA0 A0 A3 8 DQ0 DQ2 DQ4 DQ6 LDQM RAS BA1 A1 A2 9 VD D DQ1 DQ3 DQ5 DQ7 WE CS A10 VD D
9 A B C D1 D E F G H J
8
7
6
5
4
3
2
1 e
A B C D E F G H J
D/2 D
VSS DQ14 DQ12 DQ10 DQ8 UDQM A12 A8 VSS
E E/2
Pin Name CLK CS CKE A0 ~ A 12 BA0 ~ BA1 RAS
A A1
Pin Function System Clock Chip Select Clock Enable Address Bank Select Address Row Address Strobe Column Address Strobe Write Enable Data Input/Output Mask Data Input/Output Power Supply/Ground Data Output Power/Ground
*2: Top View
CAS WE L(U)DQM D Q0 ~ 15 VDD /VSS VDDQ/VSSQ
Max. 0.20
Encapsulant
b
z
*1: Bottom View < Top View*2 >
#A1 Ball Origin Indicator
K4S561633C-XXXX
SAMSUNG
Week
[Unit:mm] Symbol A A1 E E1 D D1 e b z Min 0.90 0.30 0.40 Typ 0.95 0.35 8.10 6.40 15.10 6.40 0.80 0.45 Max 1.00 0.40 0.50 0.10
Rev. 1.4 Dec. 2002
K4S561633C-R(B)L/N/P
ABSOLUTE MAXIMUM RATINGS
Parameter Voltage on any pin relative to Vss Voltage on V D D supply relative to Vss Storage temperature Power dissipation Short circuit current Symbol VIN, VOUT VDD , VDDQ TSTG PD IOS Value -1.0 ~ 4.6 -1.0 ~ 4.6 -55 ~ +150 1 50
CMOS SDRAM
Unit V V C W mA
Notes : Permanent device damage may occur if ABSOLUTE MAXIMUM RATINGS are exceeded. Functional operation should be restricted to recommended operating condition. Exposure to higher than recommended voltage for extended periods of time could affect device reliability.
DC OPERATING CONDITIONS
Recommended operating conditions (Voltage referenced to VSS = 0V, T =Commercial, Extended, Industrial Temperature) A Parameter Supply voltage Input logic high voltage Input logic low voltage Output logic high voltage Output logic low voltage Input leakage current Symbol VD D VDDQ VIH VIL VOH VOL ILI Min 2.7 2.7 2.2 -0.3 2.4 -10 Typ 3.0 3.0 3.0 0 Max 3.6 3.6 VDDQ+0.3 0.5 0.4 10 Unit V V V V V V uA 1 2 IOH = -2mA IOL = 2mA 3 Note
Notes : 1. VIH (max) = 5.3V AC. The overshoot voltage duration is 3ns. 2. VIL (min) = -2.0V AC. The undershoot voltage duration is 3ns. 3. Any input 0V VIN VDDQ. Input leakage currents include HI-Z output leakage for all bi-directional buffers with Tri-State outputs. 4. Dout is disabled, 0V VOUT VDDQ.
CAPACITANCE
Clock
(VDD = 3.0V & 3.3V, TA = 23C, f = 1MHz, VREF =0.9V 50 mV) Pin Symbol CCLK CIN CADD COUT Min 2.0 2.0 2.0 3.5 Max 4.0 4.0 4.0 6.0 Unit pF pF pF pF Note
RAS, CAS, WE, CS, CKE, DQM Address D Q0 ~ DQ15
Rev. 1.4 Dec. 2002
K4S561633C-R(B)L/N/P
DC CHARACTERISTICS
CMOS SDRAM
Recommended operating conditions(Voltage referenced to V SS = 0V, TA =Commercial, Extended, Industrial Temperature) Parameter Symbol Test Condition -75 Operating Current (One Bank Active) Precharge Standby Current in power-down mode ICC1 Burst length = 1 tRC tR C(min) IO = 0 mA CKE VIL(max), t CC = 10ns CKE & CLK VIL(max), t CC = CKE VIH(min), CS VIH(min), t CC = 10ns Input signals are changed one time during 20ns CKE VIH(min), CLK VIL(max), t CC = Input signals are stable CKE VIL(max), t CC = 10ns CKE & CLK VIL(max), t CC = CKE VIH(min), CS VIH(min), t CC = 10ns Input signals are changed one time during 20ns CKE VIH(min), CLK VIL(max), t CC = Input signals are stable IO = 0 mA Page burst 4Banks Activated tCCD = 2CLKs tRC tRC (min) -R(B)L Self Refresh Current ICC6 CKE 0.2V -R(B)N -R(B)P Notes : 1. Measured with outputs open. 2. Refresh period is 64ms. 3. K4S561633C-R(B)L** 4. K4S561633C-R(B)N** 5. K4S561633C-R(B)P** 6. Unless otherwise noted, input swing IeveI is CMOS(VIH /VIL=VDDQ/VSSQ) 800 uA 90 Version -1H 85 -1L 85 mA 1 Unit Note
ICC2P ICC2PS ICC2N
0.5 0.5 15
mA
Precharge Standby Current in non power-down mode ICC2NS Active Standby Current in power-down mode ICC3P ICC3PS ICC3N
mA 10 6 6 25 mA
mA
Active Standby Current in non power-down mode (One Bank Active)
ICC3NS
25
mA
Operating Current (Burst Mode)
ICC4
130
130
105
mA
1
Refresh Current
ICC5
185
185
165
mA
2 3 4
Rev. 1.4 Dec. 2002
K4S561633C-R(B)L/N/P
Parameter AC input levels (Vih/Vil) Input timing measurement reference level Input rise and fall time Output timing measurement reference level Output load condition
VDDQ
CMOS SDRAM
Value 2.4 / 0.4 0.5 x VDDQ tr/tf = 1/1 0.5 x VDDQ See Fig. 2
Vtt = 0.5 x VDDQ
AC OPERATING TEST CONDITIONS(VDD = 2.7V ~ 3.6V, TA =Commercial, Extended, Industrial Temperature)
Unit V V ns V
1200 Output 870 VOH (DC) = 2.4V, IOH = -2mA VOL (DC) = 0.4V, IOL = 2mA 30pF Output Z0 = 50
50
30pF
(Fig. 1) DC output load circuit
(Fig. 2) AC output load circuit
OPERATING AC PARAMETER(AC operating conditions unless otherwise noted)
Parameter Row active to row active delay RAS to CAS delay Row precharge time Row active time Row cycle time Last data in to row precharge Last data in to Active delay Last data in to new col. address delay Last data in to burst stop Col. address to col. address delay Symbol - 75 tRRD (min) tRCD (min) tRP(min) tRAS(min) tRAS(max) tR C(min) tRDL(min) tDAL (min) tCDL(min) tBDL (min) tCCD (min) CAS latency=3 Number of valid output data CAS latency=2 CAS latency=1 65 15 19 19 45 Version -1H 19 19 19 50 100 70 2 tRDL + tRP 1 1 1 2 1 0 ea 5 84 -1L 19 24 24 60 ns ns ns ns us ns CLK CLK CLK CLK 1 2,3 3 2 2 4 1 1 1 1 Unit Note
Notes : 1. The minimum number of clock cycles is determined by dividing the minimum time required with clock cycle time and then rounding off to the next higher integer. 2. Minimum delay is required to complete write. 3. Minimum tRDL=2CLK and tDAL(=tRDL + tRP) is required to complete both of last data wite command(tRDL) and precharge command(tRP). tRDL=1CLK can be supported only in the case under 100MHz with manual precharge mode. 4. All parts allow every cycle column address change. 5. In case of row precharge interrupt, auto precharge and read burst stop.
Rev. 1.4 Dec. 2002
K4S561633C-R(B)L/N/P
AC CHARACTERISTICS(AC operating conditions unless otherwise noted)
Parameter CAS latency=3 CLK cycle time CAS latency=2 CAS latency=1 CAS latency=3 CLK to valid output delay CAS latency=2 CAS latency=1 CAS latency=3 Output data hold time CAS latency=2 CAS latency=1 CLK high pulse width CLK low pulse width Input setup time Input hold time CLK to output in Low-Z CAS latency=3 CLK to output in Hi-Z CAS latency=2 CAS latency=1 Notes : 1. Parameters depend on programmed CAS latency. 2. If clock rising time is longer than 1ns, (tr/2-0.5)ns should be added to the parameter. 3. Assumed input rise and fall time (tr & tf) = 1ns. If tr & tf is longer than 1ns, transient time compensation should be considered, i.e., [(tr + tf)/2-1]ns should be added to the parameter. tSHZ tC H tC L tSS tSH tSLZ tOH 2.5 2.5 2.5 2.5 2.0 1.0 1 5.4 7 tSAC tC C Symbol Min 7.5 9.5 5.4 7 2.5 2.5 3 3 2.5 1.5 1 7 7 1000 - 75 Max Min 9.5 9.5 7 7 2.5 2.5 2.5 3 3 2.5 1.5 1 1000 -1H Max Min 9.5 12 25 -1L
CMOS SDRAM
Unit Max
Note
1000
ns
1
7 8 20 ns 1,2
ns
2
ns ns ns ns ns 7 8 20 ns
3 3 3 3 2
Note : 1. Samsung are not designed or manufactured for use in a device or system that is used under circumstance in which human life is potentially at stake. Please contact to the memory marketing team in samsung electronics when considering the use of a product contained herein for any specific purpose, such as medical, aerospace, nuclear, military, vehicular or undersea repeater use.
Rev. 1.4 Dec. 2002
K4S561633C-R(B)L/N/P
SIMPLIFIED TRUTH TABLE(V=Valid, X=Dont Care, H=Logic High, L=Logic Low)
COMMAND Register Mode Register Set Auto Refresh Refresh Entry Self Refresh Exit
CKEn-1 CKEn CS RAS CAS WE DQM BA0,1
CMOS SDRAM
A11, A12, A9 ~ A 0
A10 /AP
Note
H H
X H L H X X
L L L H
L L H X L H
L L H X H L
L H H X H H
X X
OP CODE X
1, 2 3 3 3 3
L H H
X X X V V
X Row Address L H L H X V L H X
Column Address (A0~ A8) Column Address (A0~ A8)
Bank Active & Row Addr. Read & Column Address Write & Column Address Burst Stop Bank Selection Precharge All Banks Entry Exit Entry Precharge Power Down Mode Exit DQM No Operation Command Auto Precharge Disable Auto Precharge Enable Auto Precharge Disable Auto Precharge Enable
L L
4 4, 5 4 4, 5 6
H H H
X X X
L L L H L X H L H L
H H L X V X X H X V X
L H H X V X X H X V
L L L X V X X H X V
X X X
V
X
Clock Suspend or Active Power Down
H L H
L H L
X X X
X
X X V X X 7
L H H
H
X
H L
X H
X H
X H
X
Notes : 1. OP Code : Operand Code A0 ~ A 12 & BA0 ~ BA1 : Program keys. (@MRS) 2. MRS can be issued only at all banks precharge state. A new command can be issued after 2 CLK cycles of MRS. 3. Auto refresh functions are the same as CBR refresh of DRAM. The automatical precharge without row precharge command is meant by "Auto". Auto/self refresh can be issued only at all banks precharge state. 4. BA0 ~ BA1 : Bank select addresses. If both BA0 and BA1 are "Low" at read, write, row active and precharge, bank A is selected. If BA0 is "Low" and BA1 is "High" at read, write, row active and precharge, bank B is selected. If BA0 is "High" and BA1 is "Low" at read, write, row active and precharge, bank C is selected. If both BA0 and BA1 are "High" at read, write, row active and precharge, bank D is selected. If A 10/AP is "High" at row precharge, BA0 and BA1 are ignored and all banks are selected. 5. During burst read or write with auto precharge, new read/write command can not be issued. Another bank read/write command can be issued after the end of burst. New row active of the associated bank can be issued at tRP after the end of burst. 6. Burst stop command is valid at every burst length. 7. DQM sampled at the positive going edge of CLK masks the data-in at that same CLK in write operation (Write DQM latency is 0), but in read operation it makes the data-out Hi-Z state after 2 CLK cycles. (Read DQM latency is 2).
Rev. 1.4 Dec. 2002


▲Up To Search▲   

 
Price & Availability of K4S561633C-N

All Rights Reserved © IC-ON-LINE 2003 - 2022  

[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy]
Mirror Sites :  [www.datasheet.hk]   [www.maxim4u.com]  [www.ic-on-line.cn] [www.ic-on-line.com] [www.ic-on-line.net] [www.alldatasheet.com.cn] [www.gdcy.com]  [www.gdcy.net]


 . . . . .
  We use cookies to deliver the best possible web experience and assist with our advertising efforts. By continuing to use this site, you consent to the use of cookies. For more information on cookies, please take a look at our Privacy Policy. X