View PBL385411N_162716.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

PBL 385 41 November 1998
PBL 385 41 Universal Speech Circuit
Description.
PBL 38541 is a monolithic integrated speech transmission circuit for use in electronic telephones or in any other line interface application. High settable supply current for auxiliary functions, up to 6.0 mA (at high line currents). The circuit is designed to accomodate either a low impedance dynamic or an electret microphone. Microphone can be muted separately. Payphone signaling and DTMF dialling tones have a separate input that is controlled by a mute signal. A signal summing point is available at the transmitter input. An internally preset line length compensation can be adjusted with external resistors to fit into different current feed systems as for ex. 48 V, 2 x 200 ohms, 48 V, 2 x 400 ohms and 48 V, 2 x 800 ohms. The line length compensation can be shut off in either high or low gain mode. Application dependent parameters such as line balance, side tone level, transmitter and receiver gains and frequency responces are set independently by external components which means an easy adaption to various market needs. The setting of the parameters if carried out in certain order will counteract the interaction between the settings. The circuit provides four different DC - supplies to feed microphones,diallers and other more current consuming functions like handsfree systems. Pin numbers in this datasheet refer to 18-pin DIP package unless otherwhise noted.
Key features.
* Minimum number of external components, with two filtered DCsupplies, 7 capacitors and 11 resistors. Easy adaption to various market needs. Mute control input for operation with DTMF - generator. A separate signaling input for payphone and DTMF tones controlled by mute. Transmitter and receiver gain regulation for automatic loop loss compensation. Extended current and voltage range 4 - 130 mA, down to 2 .2V. Differential microphone input for good balance to ground. Balanced receiver output stage. One stabilized DC - supply for low current CMOS diallers and or electret microphones. One settable current limited supply with 6 mA max. current. Short start up time. Excellent RFI performance. 18 - pin DIP and 20 - pin SO packages.
* * *
*
* * * *
1
DTMF input
10
PBL 385 41
AD AT AR
17
12
Mic.
13
DC-supply
AM
18
* * *
Telephone line
8
9
7
6
5
11
3
2
15
16
14
+4
Mute (active low)
DC2 - output for external devices
+
+
Gain regulation
2
+
20-pin plastic SO 1. Impedance to the line and radio interference suppression 2. Transmitter gain and frequency responce network 3. Receiver gain and frequency responce network 4. Sidetone balance network 5. DC supply components
P
B L
5
4
3
1
38
DC1- output for external devices
5
P
B
18-pin plastic DIP
Figure 1. Functional diagram DIP package.
1
L
38
5
41
41
PBL 385 41
Maximum Ratings
Parameter Line voltage, tp = 2 s Line current, continuous DIP Line current, continuous SO package Operating temperature range Storage temperature range No input should be set on higher level than pin 4 (+C).
Symbol Min Max Unit
VL IL IL TAmb TStg
0 0 0 -40 -55
18 130 100 +70 +125
V mA mA C C
MUTE R = 0-4k L 0 ohm when artificial line is used 5H+5H
VM IM IL
+
R feed = 400+400 C
ARTIFICIAL LINE
+ LINE
I DC2
MIC
Z Mic = 350 V3
+
E = 48.5V
V2
600
VL V1
VDC2 IDC1 VDC1
PBL 385 41 with external components See fig. 4 REC
V4
Z Rec= 350
- LINE
C = 1F when artificial line is used 470F when no artificial line
Figure 2. Test set up without rectifier bridge.
MUTE
VM Uz= 15-16V IL V
IM
5H+5H R
RL = 0 - 4k
+ LINE
Z Mic = 350
MIC
+
feed = 400+400
1F V2
600
L
I DC2 VDC2 IDC1 V1 VDC1
V3
+
E = 50.0V
PBL 385 41 with external components See fig. 4 REC
V4
Z Rec = 350
- LINE
Figure 3. Test set up with rectifier bridge.
+Line
1
C9 220n DTMF input
10
PBL 385 41
AD AT AR
17
R14 310 Rec. 350
R16 Mic. 350 2.7k
12 13
DC-supply
AM
18
8
Mute
(active low)
7
9
5
6
11
3
2
R7 910 R8 560 R10 6.2k
15
C6 47n
16
14
R11 62k
+4
DC1 - output for external devices DC2 - output for external devices C7 47F R17
4k
R4 18k
C3 100n
* R1
Gain regulation C11 47F
+
+
* R2a
R5 22k
R6 75 >0.5W
R12 11k R9 11k
C5 100n
R13 10
R3 910
+
C1 47F
C2 15n
* R2b
-Line
Figure 4. Circuit with external components for test set up. 2 x 400 48V. * Not used in test set up. DIP package pinning.
2
PBL 385 41
Electrical Characterisics
At TAmb = + 25 C. No cable and line rectifier unless otherwise specified. Parameter Line voltage, VL Transmitting gain, note 1 2 2 2 2 Ref. fig. 2 2 Conditions IL = 15 mA IL = 100 mA 20 *10 log (V2 / V3); 1 kHz RL = 0 RL = 400 RL = 900 - 2.2 k 1 kHz, RL = 0 to 900 200 Hz to 3.4 kHz 1 kHz 200 Hz - 3.4 kHz 2% distortion, IL = 20 - 100 mA 200 Hz - 3.4 kHz IL = 0 - 100 mA, V3 = 0 - 1 V Psoph-weighting, Rel 1 Vrms, RL = 0 20 * 10 log (V4 / V1); 1 kHz RL = 0 RL = 400 RL = 900 - 2.2 k 1 kHz, RL = 0 to 900 200 Hz to 3.4 kHz 1 kHz, 1 kHz, 200 Hz - 3.4 kHz 2% distortion, IL = 20 - 100 mA Measured with line rectifier 200 Hz - 3.4 kHz, IL = 0 - 100 mA, V1= 0 - 50 V A-weighting, Rel 1Vrms, with cable 0 - 3 km, O = 0.4 mm 0 - 5 km, O = 0.5 mm, Min 3.3 11 41 43.5 46 3 -1 13.5 Typ 3.7 13 43 45.5 48 5 Max 4.1 15 45 47.5 50 7 1 17 20.5 1.7//(2.7) note 3 1.5 3 -75 -18.5 -16 -13.5 3 -1 -16.5 -14 -11.5 5 -14.5 -12 -9.5 7 1 Unit V V dB dB dB dB dB k k Vp Vp dBPsoph dB dB dB dB dB k Vp Vp
Transmitting range of regulation Transmitting frequency 2 response Transmitter input impedance, pin 3 2 Microphone input impedance 2 Transmitter dynamic output 2 Transmitter max output Transmitter output noise Receiving gain, note 1 2 2 2 2 2 2 2 2 2 2 3
Receiving range of regulation Receiving frequency response Receiver input impedance Receiver output impedance Receiver dynamic output note 2 Receiver max output
38 3(+310)note 3 0.5 0.9
Receiver output noise
2
-85
dB A
Mute input voltage at mute (active low) DC1 -supply voltage Pin 9 DC2-supply voltage Pin 8 DC-output pin 8 input leakage current (no supply) DTMF transmitting gain DTMF input impedance
2 2 2 IL = 20 - 100 mA R17 = 4k; IDC1 =2 mA IL = 20 - 100 mA IDC = 0 mA IDC = 2 mA VDC = 2.35 V VM = 0.3 V, 1 kHz 1 kHz
0.3
V
3.4 2.1 1.95
3.7 2.35 2.2 0.1 26.5 25
4.0 2.6 2.6
V V V A dB k
4 2 2
24.5 20
28.5 30
Notes 1. Adjustable to both higher and lower values with external components. 2. The dynamic output can be doubled, see applications information. 3. External resistor in the test set up. 4. The DC output voltage is reduced at low line voltage (see page 8). 3
PBL 385 41
+L 1 TO 2 TI 3 +C 4 Mute 5 GR 6 DCS1 7 DCO2 8 DCO1 9
18 17 16 15 14 13 12 11 10
RE 2 RE 1
+L 1
20 RE 2 19 RE 1 18 DR 17 RI 16 -L 15 MI 2 14 MI 1 13 MO 12 DI 11 NC
DR RI -L MI 2 MI 1 MO DI
TO 2 TI 3 +C 4 Mute 5 GR 6 DCS1 7 DCO2 8 DCO1 9 NC 10
18-pin DIP
20-pin SO
Figure 5. Pin configuration.
Pin Descriptions
Refer to figure 5. DIP SO Name 1 2 1 2 +L TO Function Output of the DC-regulator and transmitter amplifier, connected to the line through a polarity guard diode bridge. Output of the transmitter amplifier, connected through a resistor of 47 to 100 ohm to -L, sets the DC-resistance of the circuit. The output has a low AC output impedance and the signal is used to drive a side tone balancing network. Input of the transmitter amplifier. Input impedance 17 kohm 20 %. Positive power supply terminal for most of the circuitry inside the PBL 385 41 (about 1 mA current consumption). The +C pin must be connected to a decoupling capacitor of 47 F to 150 F. When low, speech circuit is muted and the DTMF input is enabled. Maximum voltage (at mute) is 0.3 V, current sink requirement of external driver is 50 A. Control input for the gain regulation function. Control input to the DC1-supply. A resistor to -line sets the maximum current load of the supply. Output of the DC2-supply. Output of the DC1-supply. Input for the DTMF-signal. Input impedance 25 kohm 20 %. Output of the microphone amplifier or DTMF-amplifier.
3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
3 4 5 6 7 8 9 12 13 14 15 16 17 18 19 20 10 11
TI +C Mute GR DCS 1 DCO 2 DCO 1 DI MO MI 1 MI 2 -L RI DR RE 1 RE 2
} }
Inputs to the microphone amplifier. Input impedance 1.7 kohm 20 %. The negative power terminal, connected to the line through a polarity guard diode bridge. Input of receiver amplifier. Input impedance 38 kohm 20 %. Control input for the receiver amplifier driving capability. Receiver amplifier outputs. Output impedance is approximately 3 ohm. Not connected Not connected
4
PBL 385 41
Functional description
Design procedure; ref. to fig.4. The design is made easier through that all settable parameters are returned to ground (-line), this feature differs it from bridge type solutions.To set the parameters in the following order will result in that the interaction between the same is minimized. 1. Set the circuit impedance to the line, either resistive (600) or complex. (R3 and C1). C1 should be big enough to give low impedance compared with R3 in the telephone speech frequency band.Too large C1 will make the start-up slow. See fig. 6. 2. Set the DC-characteristic that is required in the PTT specification or in case of a system telephone,in the PBX specification(R6). Observe the power dissipated.There are also internal circuit dependent requirements like supply voltages etc. 3. Set the attac point where the line length regulation is supposed to cut in (R1 and R2). Note that in some countries the line length regulation is not allowed. In most cases the end result is better and more readily achieved by using the line length regulation (line loss compensation) than without. See fig. 13. 4. Set the transmitter gain and frequency response. 5. Set the receiver gain and frequency response. See text how to limit the max. swing to the earphone. 6. Adjust the side tone balancing network. 7. Set the RFI suppression components in case necessary. In two piece telephones the often "helically" wound cord acts as an aerial. The microphone input with its high gain is especially sensitive. 8. Circuit protection. Apart from any other protection devices used in the design a good practice is to connect a 15V 1W zener diode across the circuit , from pin 1 to -Line.
+Line 1 4 a) R3 Cx 820 3 2 Rs 1 + C1 Example: How to connect a complex network. 220+820//Cx -Line b) c) 220
PBL 385 41
C2
R6
Figure 6. AC-impedance.
complex network capacitor is connected directly to ground, case c). making the ratio Rs/220+820 and thus lessening the error signal. Conclusion: Connect like in case c) when complex impedance is specified.
Impedance to the line
The AC- impedance to the line is set by R3, C1 and C2. Fig.6. The circuits relatively high parallel impedance will not influence it to any noticeable extent. At low frequencies the influence of C1 can not be neglected. Series resistance of C1 that is dependent on the temperature and the quality of the component will cause some of the line signal to enter pin 4. This generates a closed loop in the transmitter amplifier that in its turn will create an active impedance thus lowering the impedance to the line. The impedance at high frequencies is set by C2 that also acts as a RFI suppressor. In many specifications the impedance towards the line is specified as a complex network. See fig. 6. In case a). the error signal entering pin 4 is set by the ratio Rs/R3 (910), where in case b). the ratio at high frequencies will be Rs/220 because the 820 resistor is bypassed by a capacitor. To help up this situation the
DC - characteristic
The DC - characteristic that a telephone set has to fulfill is mainly given by the network administrator. Following parameters are useful to know when the DC behaviour of the telephone is to be set: * * * * The voltage of the feeding system The line feeding resistance 2 x....... ohms. The maximum current from the line at zero line length. The min. current at which the telephone has to work (basic function). The lowest and highest voltage permissible across the telephone set. The highest voltage that the telephone may have at different line currents. Normally set by the network owners specification.The lowest voltage for the telephone is normally set by the voltages that are needed for the different parts of the telephone to function. For ex. for transmitter output amplifier, receiver output amplifier, dialler, speech switching and loudspeaker amplifier in a handsfree telephone etc.
* *
+ Line
3 1
+
AM
2
AT
AR
4 Transmitter summing input
- Line
Mute
Figure 7. Block connections.
5
PBL 385 41
V
16 14 12 10 8 6 4 2
V telephone line V line V pin 4
V pin 2
V pin 9 V pin 8
(DC supply)
I
20
Figure 8. DC-Characteristics. (R6=75)
R6 will set the slope of the DC-char. and the rest of the level is set by some constants in the circuit as shown in the equation below. The slope of the DC-char. will also influence the line length regulation (when used ) and thus the gain of both transmitter and receiver. See the table under gain regulation. R6 also acts as power protection for the circuit, this must be kept in mind when low values of R6 are considered. microphone amplifier can be used for dynamic or electret transducers. See fig. 10. An electret microphone with a built in FET amplifier is to be seen from outside as a high impedance constant current generator and is normally specified with a load resistance of 2k. This is to be considered as max. value and by using it will render the max. gain from the microphone. This level of input signal that is unnecessary high will result in clipping in the microphone amplifier and could in mute condition permeate through the input to the circuits reference and this way to all functions, resulting among other things in a bad mute. Hence it is better regarding noise perfomance and mute to rather use the gain of the microphone amplifier than the gain of the microphone itself (in case of electret) flat out. A more suitable level of gain from the microphone is achieved by using a load resistance of 330 - 820. A low microphone impedance will also improve RFI suppression. Gain setting to the line is done at the input of the transmitter. The microphone amplifier has its own
L
40
60
80
100
120
mA
VLine 2 + 1.5 R 6 Iline Vtelephoneline 1.5V + Vline
Microphone amplifier
The microphone amplifier in PBL385 41 is divided into two stages. The first stage is a true differential amplifier providing high CMRR (-55 to -65 dB typical) with voltage gain of 19 dB. This stage is followed by a gain regulated amplifier with a regulation range of 5 2 dB. The input of the 6
temperature stable reference to prevent overhearing to other parts and functions on the chip.It is possible to use the microphone amplifier as a limiter ( added to the limiter in the transmitter output stage ) of the transmitted signal. See fig.9. The positive output swing is then limited by the peak output current of the microphone amplifier. The negative swing is limited by the saturation voltage of the output amplifier. The output of the amplifier is DCvice at internal reference level (1.2V). The lowest negative level for the signal is reference minus one diode and sat. transistor drop. (1.2-0.6-0.1 = 0.5V) The correct clipping level is found by determining the composite AC- and DC-load that gives a maximum symmetrical unclipped output. This signal is then fed into the transmitter amplifier at a level that renders a symmetrical signal clipping on the line. (adjust with ratio R4,R5) The total transmitter gain when an electret microphone is used can then be adjusted with the load resistor of the electret microphones buffer amplifier.
PBL 385 41
PBL 385 41
DC ( ref. 1.2V )
constant current generator
(a)
PBL 385 41
11 12
(b)
11 12
4
PBL 385 41
M
13
13
M +
+ Dynamic microphone
ref. minus a diode 0.5V
11
R
Unbalanced electret mic. with balanced signal, DC-supply from pin 4.
DC
Pin 8 or9.
DCload
ACload
(c)
11 12
4 PBL 385 41
(d)
11 12
PBL 385 41
M
13
M
13
C+
+
+ Balanced electret microphone
DC-load = R4+R5 AC-load = R4+R5//ZTI
Balanced electret microphone. An additional RC filterlink is recommended if pin 4 is used as a supply.
Figure 9. Microphone amplifier output clipping.
Figure 10. Microphone solutions.
Transmitter amplifier
The transmitter amplifier in PBL38541 consists of three stages. The first stage is an amplitude limiter for the input signal at TI, in order to prevent the transmitted signal to exceed a certain set level and cause distortion. The second stage amplifies further the signal from the first and adds it to a DC level from an internal DC-regulation loop in order to give the required DC characteristic to the telephone set. The output of this stage is TO. The third stage is a current generator that presents a high impedance towards the line and has its gain from TO to +L. The gain of this amplifier is ZL/R6 where ZL is the impedance across the telephone line. Hence, the absolute maximum signal amplitude that can be transmitted to the line undistorted is dependent of R6. (amplitude limiting) The transmitter gain and frequency response are set by the RC-network between the pins 11 and 3. See fig.11. The capacitor for cutting the high end of frequency band is best to be placed directly at the microphone where it also will act as a RFI suppressor. The input signal source impedance to the transmitter amplifier input TI should be reasonably low in order to keep the gain spread down, saying that R4//R5 (see fig. 4) must be at least a factor 5 lower than the ZTin. Observe that the capacitor C1 should have a reasonably good temperature behaviour in order to keep the impedance rather constant. The V+Cs influence on the transmitter DC-characteristic is shown in the fig.8 (DC-characteristic), therefore the transmitter gain would change if the transmitted signal gives reason to an acvoltage leak signal across C1 since this is a feedback point. If the transmitter has an unacceptable low sving to the line at low line currents <10mA the first step should be to examine if the circuits DC characteristic can be adjusted upwards. How to calculate the gains in the transmitter channel. See fig. 2 and 4. Microphone amplifiers first stage 19 dB. Microphone amplifiers regulated second stage 10.5 dB - 15.5 dB Regulation interval 10.5 - 15.5 dB low gain 19.0 + 10.5 dB = 29.5 dB high gain 19.0 + 15.5 dB = 34.5 dB
V2 RM R5 Rload = GM GTX V 3 Zmic + RM R4 +R5 R6
RM = Microphone amplifier input resistance Rload = Rline // Rtelephone ex. calculate the gain of the transmitter stage GTX at 0 - line length:
43 = 20 log(
(1.7 / /2.7)k (17 / /22)k 600 / /910 ) + 29.5 + 20 log( ) + GTX + 20 log( ) 350 + (1.7 / /2.7)k 18k + (17 / /22)k 75
43 = -2.51+ 29.5 - 9.17 + GTX + 13.66
GTX = 11.52dB
7
PBL 385 41
11 (a) RA
3
11 (b) CA RA CA
3 RA
11 (c) CA
3
(a),(c), (d)
CB RB attenuation
(a and b) attn. = RTI//(RTI+RA)
no attn. = RA = 0 11 CC RA (d) RA CA RB CA 3 11 (e) 3
11 CC RA CA (f)
3
(b),(e)
big CA
RB attn.without dc.
CB
small CA
RB
CB
(f)
attenuation
attn.without dc.
Figure 11. Possible network types between microphone amplifier and transmitter.
Receiver amplifier
The receiver amplifier consists of three stages, the first stage being an input buffer that renders the input a high impedance. The second stage is a gain regulated differential amplifier and the third stage a balanced power amplifier. The power amplifier has a differential output with low DC- offset voltage, therefore a series capacitor with the load is normally not necessary. The receiver amplifier uses at max. swing 4-6 mA peak. This current is drawn from the +Line. The driving capacity of the power stage can be optimized by a resistor at pin 16, an other method is to connect a resistor in series with the earphone itself fig.12 b.). The gain and frequency response is set at the input RI with a RC-network. The receiver gain can be regulated. The range of regulation from the input to the output is 5 2 dB (19 to 24dB). The balanced earphone amplifier can not be loaded to full (both current and signal level ) single ended.The signal would be distorded when returned to ground. A methode is shown in fig.12 d. how to connect a light load (5k ac. or DC wise) to the output. It is preferred that both outputs are loaded the same. The receiver has, as a principal protection, two series diodes anti parallel across its output to limit the signal to the earphone and thus preven(a) (b) (c)
ting an acoustical shock. A resistor in series with the output can very well be used to increase the protection level. Note, that the noise in the receiver is allways transmitter noise that has been more or less well balanced out by the side tone network. The RC - network (optional) at the output is to stabilize against the inductive load that an earphone represents.
(d)
PBL 38 5 41
+ + Rx
17
PBL 38 5 41
+ Rx
PBL 38 5 41
17 17
+
+
+ Rx -
(C) Z
18
18
18
Z (C) Z > 5k
The capacitor C is optional
Figure 12. Receiver arrangements.
receiver gain pattern versus line length. The following will show, what to alter, to change the look of the curve. a). Adjustable with the divider R4,R5 for the transmitter and with R12 for the receiver. b). The attack point of the regulator is adjusted with the divider R1,R2a and R2b to either direction, up or down, on the line current axis. c). The angle of elevation of the curve is mainly set by the value of R6 but is also adjustable with R2b. If the DC-characteristics is set according to the line parameters and a correct value for R6 is chosen the angle is mostly correct but it can be adjusted with R6. The adjustement will affect the DC-characteristics aswell as most of the other parameters. This is why the DCcharacteristic is set early in the design phase.
Gain regulation.
Both the receiver and transmitter are gain regulated (line loss compensated). There is a fixed default compensation on the chip that can be adjusted or or set to constant high or low gain mode. The input impedance at the gain regulation pin 6 is 5.5k 20%. The default regulation pattern is valid when the input is left open. Fig.13 shows a typical transmitter or 8
PBL 385 41
Battery feed Regulation:
R1
R2a
R2b
R6
dB
c. b.
700k
600k
75 47
a.
48V, 2 * 200 48V, 2 * 400 48V, 2 * 800
No regulation: All feedings Set for low gain Set for high gain 22k 75k 47 - 75
What is balancing the side tone?
To understand that side tone balancing is to counteract the signal, that is transmitted via the microphone and transmitter to the line, returning to the earphone via the receiver. That presence of a strong side tone signal is disturbing in a way that one quite instictively lowers ones own voice level thus lowering the signal level for the other party. But again, if the balance is too good (seldom the case) the earphone will feel "dead". In practical terms what is expected is the same amplitude of ones own voice in the ear as when not talking in a telephone. The need to lower the side tone level
a).
1
Tx
2 15
b).
R7
R6 C5
Figure 14. The side tone suppression principle.
9
}
75
High limit
Sweden, apply for spec. application
Low limit
I
47 - 75
L
Figure 13. Gain regulation principle.
where no balancing has been done is in the order of 6 - 12 dB. To understand that the side tone is influenced by other factors like, the impedance of the line and the signal that enters the ear acoustically directly from the mouth and from the mouth through the material in the handset. The signal that enters the microphone from the earphone acoustically will also influence the return loss factor to the telephone line. To understand that the side tone network can be trimmed to form a veritable "distortion analyser", so that the distortion that is present from the microphone, will be the only signal entering the earphone and this signal even being small will sound very bad. It is better to induce some of the fundamental frequency back by making
Telephone set side
the balance less perfect at that frequency. This is valid for a network that is trimmed to only one frequency. It is to strive to trim the network such that it will attenuate the fundamental and the harmonic frequencies alike throughout the different line combinations. To understand that if one of the two signals entering the balancing system from either direction, direct from microphone or via the line is clipped, will result in a very distorted signal entering the receiver amplifier and thus the earphone. Further , to remember that side tone is a small signal that is the difference of two large signals and that the amplitude of the distortion can be up to ten times the amplitude of the fundamental frequency.
Line side
A short guidance for understanding the side tone principle. (See fig.14.)
Assuming the line impedance to be 600. ( theorethical value ) Z1 = Line impedance Z2 = The telephone set impedance 600 Z1//Z2 = 300 R6 will have a certain value 39 - 100 to give the telephone a specified DCcharacteristic and overcurrent protection. Assuming that this DC-characteristic requires R6=60, hence it will be 1/5 of the Z1//Z2. This will in transmitting mode result that 1/5 of the ac-signal that is on the line appear across R6.
PBL 385 41
17
Rx
18
Z2
Z1
c).
R8
R10
C6 R11
Zbal
R9
R12
PBL 385 41
Note that the signals at points a. and b. are 180 degrees off phase. 10 x R6 R7 + Zbal Note #1 R7 Zbal Note#2 The ac-signal at point c. is now 1/10 of the signal on the line because it is further divided by two from point b. (R7Zbal). Hence 10 x R10 R11 to satisfy the balancing criteria. R12 is to set the receiver gain. ( can also be a volume control potentiometer). Note #1 These values ensure that the frequency behaviour of the transmitter is minimal. With the ratio 1/10 the influence is 1 dB, and with ratio 1/20 its 0.5 dB. Note #2 If the R7 is made low ohmic compared with Zbal, it will load the latter and result in a bad side tone perfomannce, again if the R7 is made high ohmic compared with Zbal will result in a low signal to balance the side tone with and make the balancing difficult. Making any of the impedances unnecessary high will make the circuit sensitive to RFI. All values given here are approximate and serve as starting entities only. The final trimming of side tone network is a cut and try proposition because a part of the balance lies in the acoustical path between the microphone and earphone.
a) Mute IMute PBL 38541 5 Mute IMute
b) PBL 38541 5
c) PBL 38541 14 -L 5
d)
PBL 38541
17 Rx Mute 18 15
Muting points
VMute
14 -L
VMute
14 -L
The diode has to be low voltage drop type.
Receiver mute only.
Figure 16. Mute input.
Mute function.
The circuit has a mute function at pin 5. Sinking current from this pin will cut off the gain in the microphone amplifier (attenuation min. 60dB) and decrease the gain in the receiver amplifier to reach the confidence tone level at DTMF-dialling. The receiver mute is 40dB down from the unmuted value to satisfy those who keep the handset close to the ear at dialling. The mute signal also switches the output at pin 11 from microphone amplifier output to the signaling amplifier (payphone and DTMF signals) output. Optional conditions. For users who keep the handset from the ear the confidence tone level is too low. To alter the level, a signal can be taken from DTMF generator output to receiver input before the capacitor C6. The added impedance to this point will hardly disturbe the signal condition in active speech mode. The microphone amplifier only, can be muted by sinking current from the output pin 11. Figure 16 b.) If the system mute signal is used to other tasks than muting the speech circuit it has to be isolated. If a diode is used it has to be a low voltage drop type. The input at mute has to be below 300mV. If the mute signal has reverse polarity out of the system it can be phase changed like in c.) In case it is required to mute the receiver only, d.) it can be done by shorting the receiver input to ground before or after the input capacitor. Shorting the input pin to ground (does not have to be absolute ground) actuates a mute by driving the amplifier into saturation thus blocking the signal path and rendering a mute with high attenuation but will cause a DC-level shift at output which in its turn will cause a "click " in the earphone. This can be softened with a slower mute signal flank. If the second approach, grounding before the input capacitor is chosen, the grounding has to be low ohmic in order to render a high attenuating mute.
Reverse side tone network.
This type of side tone balancing will help when for some reason there is a need to make the R6 low < 47 and thus the signal for balancing gets small across R6. By placing the balancing network like shown in fig.15 the possible signal level is 6 dB higher than in the first case and it will also help in case when a volume control is added to the receiver.
Start up circuit
PBL 385 41 2 C6 +Line R6 R11 R12 C* Z bal. 15 R10
* To give receiver flat frequency response
Figure 15. Reverse side tone network with complex R11.
The circuit contains a start up device which function is to fast charge capacitor C1 when the circuit goes into hook- off condition. The fast charge circuit is a thyristor function between pins 1 and 4 that will stop conducting when the current drain at pin 4 is lower than 700 A + the internal current consumption ( about 1 mA). Care must be taken when connecting external load to pin 4 in order not to exeed the 700 A limit. Should this happen, it would result in an inoperative speech funktion. This circuit can not retrigger before the voltage level at C1 drops below 2V or the line voltage is below 1V. See fig. 17.
+Line 1
PBL 385 41
Tx
2
DC supply
R3 4
R6
+
C1 -Line
Figure 17. Fast startup circuit.
10
PBL 385 41
DTMF input.
The circuit provides a specific input at pin 10 for DTMF dialling signals. The output of the amplifier is controlled by the mute signal provided by the dialler. This input makes it easy to time the DTMF signals entering the line. Most of the diallers wake up at pressing of a key and the output will not be stable imidiately. This unstable state will be of some length and is limited in some telephone specifications. internal quick start circuit by locking itself into active state. (max. permissible current drain 700A) Care has to be taken when deciding the resistance value of R3. All resistances that are applied from +Line to ground (-Line) will be in parallel, forming the real impedance towards the line. This will sometimes result in, that the ohmic value of R3 is increased in order to comply to the impedance specification towards the line. The speech circuit sinks 1mA into pin 4, which means that the working voltage for the speech function V+ will decrease with increasing R3, thus starving in the end the circuit of its working voltage . This dependency is often falsely taken as a sign of that the circuit does not work down to the low line current specified, but in fact it is the working voltage at pin 4 that has become too low. It is obvious that this problem is also connected into what kind of DC-characteristic is set. See fig. 8. The circuit has further two temperature and line current compensated DC supplies DC1 and DC2. DC2 is a voltage supply for supplying diallers, can be used for memory back up because it does not leak any current back into the circuit. Typical voltage 2.4V down to line voltage of 4.1V, in case the line voltage is lower than 4.1V calculate ; actual line voltage minus 1.9V. In order to prevent noise entering the line, a series resistor and a reservoir capaciotor is recommended in for this output.The output current is given to be 2 mA in the specification. DC1 is a 3.7 V (typ.) supply whose, for the design required maximum output current can be set at the control input pin 7. The set current will flow constant (necessary to keep the line current constant) used or not used by a function, so care has to be taken when setting the current limit so it wont be unnecessary high. The maximum current that can be set and drawn by maintaining the voltage level is 2.0 mA (up to 6 mA can be set if the line current so allows). This supply is ment to be used to supply microphones, Ericssons handsfree IC's switching parts (see applications), opto couplers etc. and in payphones its auxiliary functions. The fourth DC-supply VPA has an advantage that it does not influence the circuits DC characteristics even at high current drain. The supply has a floating ground reference in the +line in order to minimize RFI problems and is used to supply the power amplifier of a handsfree telephone ( PBL3881, 38813 ). These circuits have a current controlled charging of the supply capacitor and the control signal is taken across the resistor R6. In case a monitor amplifier is required where the ground reference is hardly necessary, it can be supplied from VPA or like in alt. b in fig. 18.
Power supplies DC1, DC2, V+C and VPA (See fig.18)
PBL 38541 generates its own DC supply V+C dependent of line current with an internal shunt regulator. This regulator senses the line voltage VL via R3 and line current via R6 in order to set the correct V+C so the circuit can generate the required DC characteristic for a given line resistance RLine and the line feeding data of the exchange. A decoupling capacitor is needed between pins +C and -L. The V+C supply changes its voltage linearly with the line current. It can be used to feed an electret microphone. Caution must be taken though not to drain too much current out of this output because it will affect the
IL
Hook switch
+Line
1
R3 RLine VPA
+
V+C 4 +
PBL 385 41
V
Ref. 1.2V
1-10M 7 R17
VL
+
+
3.7V
9 0-470
b.
RFeed
Tx
-
VDC1 VDC2
15k Lim 15k 3 14 6V
8
a. + Vexh.
VMon.
2
6V
+
+ 4.7-47
F
+ 4.7-47
F
+
C1 R6
-Line
a. Supply arrangement for a handsfree system power amplifier. For ex. PBL 388 13 b. Supply arrangement for a call monitor cicuit.
Figure 18. DC - supply system for external loads.
11
PBL 385 41
Short about Radio Frequency Interference RFI.
HF suppression at the microphone input. The HF-signal at the microphone input can be seen composed as of two components. One component being the differential (between pins 12 and 13) and the second related to ground at pin 14. Of these two, the first is the most serious, entering the
amplifier directly being amplified and detected. The second component is less serious because it affecting both inputs alike and most of it will be balanced out of the amplifier. There might be the case where the HF-signal will have such an amplitude that the amplifier can not balance it out. Then components must be filtered with capacitors and maybe resistors. It is extremely important that everything that is done at the input is in balance, otherways the problem might get worse instead of better. The extreme balance requirement
goes all the way to the PCB-layout. Small unbalance signals can be corrected with capacitors marked with*) this requiring high precision components. See fig.19a. The solution shown is rather expensive but with precision components it renders good filtering at the input. If the main problem is the signal between the inputs, try to increase the 1nF capacitor but make the others procentually smaller in order to maintain the frequency response. A more simple solution, that is sufficient in most of the cases is also shown in fig.19b.
a)
10n 10n 11
b)
11 <20n
+
200470 + Mic. 1 + 11
c)
*
100 Mic. 100 1n 13 12
10n
M
+
12 Mic. 1n 13
12
M
+
14
1n
M
13
+
*
10n 10n
14
PBL385 41
Line
<20n
PBL385 41
Line
10n
200470
1
14
PBL385 41
Line
Dynamic microphone
Dynamic microphone (simplified)
Electret microphone
Figure 19. RFI elimination at microphone amplifier input.
HF-suppression at the receiver output. The problem here is of the same kind as at the microphone amplifier input but will be easier to solve because of the much lower impedance and level of gain. The solution is shown in the fig. 20. No capacitors should be connected directly from pins17 or 18 to ground because of the low output impedance,series resistance of at least 10 must be used if there is a tendency to self oscillation. Other paths for the HF-signal to enter the audible system. To find out if the problem originates in the DTMF-generator disconnect the generator and disconnect the mute input. If the problem is small try to connect a capacitor from mute input to -line pin 14. DTMF circuits are sensitive to RFI because of their high impedance at the input pins, especially the keyboard inputs. These inputs are not possible to filter with large capacitors because of the keyboard scan12 ning pulses (1s) that would be loaded down. To shield the keyboard will some times help. The polarity guard bridge can also act as a rectifier and demodulator, of the HF-signals. Connect 1nF capacitors across each diode in the bridge. There is a capacitor across the line C10, this is for RFI suppression but also to stabilise the whole system. The cappacitor C10 shoud be connected like in figure 22. The frequencies at which the RFI comes through are in the region of 10-1000MHz. The resistance of the C10 will be somewhere 0.01-10 hence even the shortest lenght of connector on the PCB board or wire wil be in the same region of resistance and thus of greatest of importance.These actions described above should, when applied correctly, take care of the RFI coming in from the telephone line. The second way for the RFI to enter the system is to penetrate the PCB board capacitively. The test methode is to place a metal sheet under the telephone set to be tested and inject the sheet with RF signal. The most used and effective counter measure to this kind of RFI penetration is to shield the telephone set, at least the bottom of it, that is closest to the main PCB board by metal foil or by spraying the plastic casing with metallic matter. See figure 21. This methode does not necessarily count out the RFI components that are recommended earlier.
17
10-100
<47n
Rx
18
PBL385 41
15 14
- Line
Figure 20. RFI elimination at receiver amplifier output.
+ +
-
10-100
<47n
PBL 385 41
Radio interference originating from mobile phones
The problem with direct radiated RFI has accentuated nowadays because of the growing numbers of mobile and especially pocket telephones. Thus it is today rather common that a RF transmitter with output power of several watts in form of a mobile telephone is placed quite close to an analog telephone. There is a simultaneous even bigger problem coming from these portable phones of digital time-multiplex type like the GSM. The GSM signal consists of 900 MHz carrier that is transmitted in short signal bursts 1/8 of time and with a repetition frequency of slightly higher than 200 Hz. This signal will be directly radiated to all parts in a conventional telephone set. All unlinear elements as most of the semiconductors will envelope detect this signal and thus feed the 200 Hz signal with harmonics into all points of the telephone. The methode to counteract this problem is the same as before with a difference that it has to be done with much more precision. The principle is to attenuate the HF signal to a level where the detected 200 Hz signal is below a disturbing level especially at high sensitive points like at the microphone input. Following aspects ought to be considered: 1). Do not make any points in the circuitry more high impedive than necessary. Keep all cables, wires and tracks on PC-board as short as possible. Decouple all sensitive points to an internal ground with capacitors especially the microphone amplifier input. To include series elements like resistors and inductors in all long wires or cables that could act as aerials. For ex. microphone cable, earphone cable, cable to the telephone network, mute wire and cable to the keypad. Comprehend that it is a question of a HF- design,so that all used decoupling components are well suited to the frequencies at hand. (up to several GHz). HF- design includes also that tracks on the PC-board act as inductors and therefore it is the more important that the decoupling capacitors are placed directly between the actual points and not
SIOV Line in 5 - 10
V and I protection
C10 Metallic shield, sprayed or foil
The electronic circuitry
Plastic enclosure
RF radiating measuring sheet. RF-gen.
Figure 21. How to measure the RFI pickup.
via tracks on the board (See fig. 22). Balanced points like a differential microphone input may have to be decoupled differentially between the inputs and "common mode" to common ground each input separately. 8). A virtual ground may have to be created into which all outgoing cables are decoupled in order to bypass the RF- signal. See fig. 23. 9). Think that even overvoltage and overcurrent protectors can be acting as HF detectors. 10). Shields that are connected to the internal ground can be of help. 11). Control that no already detected signals from for ex. dialler enter the speech circuit via the mute function. 12). Try to reach a high packing density on the PC-board. 7). 13). Connect components as close to the IC as possible. Connect especially decoupling capacitors close to the ground pin of the IC. The terminal circuits from Ericsson Components are manufactured in IC processes with large internal capacitors on the chip to counteract RFI disturbanses in every possible way. The simplest method to test the susceptibility of an apparatus to RFI is to take a portable phone of an actual type and move it transmitting acros the phone, cables and handset. Measure the signal at earphone output aswell as on the line. Finally; to design an ordinary analog telephone to fullfil todays requirements is not a low frequency but a high frequency task.
2). 3).
Not like this Like this
Figure 22. RFI elimination at PCB layout level.
Microphone
4).
5).
Earphone
Line
6).
Resistor or Virtual ground inductors
Common gnd. of the telephone
Figure 23. RFI elimination in the wiring.
13
PBL 385 41
1-10M 1 Hook switch
VDD
10
PBL 38541
AD AT AR
17 100
CMOS DIALLER
220
MUTE 9
1F 12
Rec. 18 10n
MIC. 220 33k 1F
13 DC-supply 8 7 9
AM
Telephone line 5 6 11 3 2 15 47n 16 14
DTMF 12 GND
+4
10
1 4 7
2 5 8 0
3 6 9 #
680p 3.3n
100
100
18k R1
100n
910 560
6.2k
62k
910 11k 11k 10 15n 15V
*
R17 4k C7 47F
Gain regulation C11 47F R2a
+
+
22k
75 1W 100n
+
47F
R2b
Figure 24. Typical DTMF tone dialling telephone ( DIP package pinning ).
Ordering Information
Package Temp. Range Part No.
Plastic DIP Plastic SO Plastic SO
-40 to +70C -40 to +70C -40 to +70C
PBL 385 41/1N PBL 385 41/1SO PBL 385 41/1SO:T
Information given in this data sheet is believed to be accurate and reliable. However no responsibility is assumed for the consequences of its use nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Ericsson Components. These products are sold only according to Ericsson Components' general conditions of sale, unless otherwise confirmed in writing.
Specifications subject to change without notice. 1522-PBL 385 41/1 Rev.A (c) Ericsson Components AB November 1998
Ericsson Components AB S-164 81 Kista-Stockholm, Sweden Telephone: +46 8 757 50 00 14

▲Up To Search▲

Price & Availability of PBL385411N

	To Download PBL385411N Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .