|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
A MICROSEMI COMPANY AudioMAXTM PRELIMINARY LX1710/1711 Class-D Mono Power Amplifier Controller IC The LX1710/1711 is a monolithic high performance integrated class-D controller IC designed for high efficiency audio requirements such as portable or battery operated products, automotive amplifier, and multimedia applications. This high frequency, full audio bandwidth switching power amplifier controller, is a completely new design with dramatically improved performance over Linfinity's previous generation amplifier products. Enhancements include better SNR, lower noise floor, and reduced THD. Combined with output power MOSFET's and an output filter, the LX1710/1711 is a complete class-D audio solution. A complete audio amplifier module is available to quickly evaluate the LX1710 controller. Simply connect the amplifier to the power source, audio signal, and speakers. Reference designs support a variety of requirements including multi channel systems, subwoofers, and various speaker loads (2 amplifier solution can easily be adjusted for frequency response, optimized for efficiency and performance, or designed to minimize PCB area and component count. The LX1710/LX1711 is available in a space saving 28-pin SSOP package. Integrated Switching Class-D W W W .Microsemi .COM Single Channel Controller IC Full 20Hz-20kHz Audio Bandwidth High Fidelity (LX1710) Or High IMPORTANT: For the most current data, consult MICROSEMI's website: http://www.microsemi.com Class-D Amplifier Efficiency Comparison Power (LX1711) Versions Available Single Supply Operation THD+N <0.05% Typical (1Wrms, 1kHz, 4 Maximum Efficiency 80%-85% Output Power >50Wrms (LX1711, 4 PSRR -70dB Typical Differential Input To Minimize Noise Effects Supports Multi-Channel Systems Complete LXE1710 Amplifier Evaluation Module Available 28-Pin SSOP Package Notebook Computers Desktop Computers Multimedia Speakers Automotive Amplifiers And Headunits Battery Operated Equipment (Megaphone, PA System) Portable Audio (Boom Box) Wireless Speakers High Power Subwoofer LX 1 7 1 0 /1 7 1 1 LX 1 7 1 0 /1 7 1 1 TJ (C) 0 to 70 Copyright (c) 2000 Rev. 1.1, 2000-12-01 VDD 7V-15V 7V-25V DB Plastic SSOP 28-PIN LX1710CDB LX1711CDB Page 1 Microsemi Linfinity Microelectronics Division 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 A MICROSEMI COMPANY AudioMAXTM PRELIMINARY LX1710/1711 Class-D Mono Power Amplifier Controller IC DB PACKAGE THERMAL RESISTANCE-JUNCTION TO AMBIENT, JA 50C/W VREF GND N .C . V25 RPW M CPW M IN P U T + IN P U T IN A M P O U T SLEEP MUTE STATUS E A IN EAOUT 14 28 C LO C K ISCP VD D PVD D P+ N+ NPPG N D CN F BKF BK+ F AO U T W W W .Microsemi .COM Junction Temperature Calculation: TJ = TA + (PD x JA). The JA numbers are guidelines for the thermal performance of the device/pc-board system. All of the above assume no ambient airflow. 15 The mono output controller is available in either an LX1711 high power version (>50Wrms, 4 supply voltage range of 7V-25V or an LX1710 high fidelity version (better SNR performance) with a supply voltage range of 7V-15V. The current rating of the external MOSFET's, the available supply voltage, and speaker load primarily limits the maximum output power. The amplifier provides high fidelity performance and it designed to operate over the full 20Hz to 20kHz audio band. Signal distortion measurements yield THD+N levels less than 0.05% (1kHz, 1Wrms). Efficiency is greater than 80% typical, which eliminates the need for heatsinks, even at maximum output power. The AudioMAXTM solution requires a single supply voltage, simplifying input power requirements where a dual supply may not be available. To minimize potential environmental noise issues and ease the integration of the amplifier into a variety of applications, features such as a balanced/differential audio input and a high power supply rejection ratio help reduce the effects of noise from the audio signal or power supply. Pin Name VREF GND N.C. V25 RPWM CPWM INPUT+ INPUT INAMPOUT SLEEP MUTE STATUS EAIN EAOUT Description 5V Reference Low Current Ground No Connect 2.5V Reference PWM Resistor Connection PWM Capacitor Connection Positive Audio Input Negative Audio Input Input Amplifier Output Sleep Input (active low) Mute Input (active high) UVLO Indicator (Open Collector Output) Inverting Input of Error Amplifier Error Amplifier Output Pin Name FAOUT FBK+ FBKCN PGND PNN+ P+ PVDD VDD CP IS CLOCK Description Feedback Amplifier Output Feedback Amplifier Non-Inverting Input Feedback Amplifier Inverting Input Supply Decoupling for NFET Drivers Output Driver High Current Ground Drive for PFET on Negative Half of Bridge Drive for NFET on Negative Half of Bridge Drive for NFET on Positive Half of Bridge Drive for PFET on Positive Half of Bridge PACKAGE DATA PACKAGE DATA Output Driver Supply Voltage Analog Supply Voltage Supply Decoupling for PFET Drivers Current Limit Sense Input Input / Output Clock for Synch Operation Copyright (c) 2000 Rev. 1.1, 2000-12-01 Microsemi Linfinity Microelectronics Division 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 2 A MICROSEMI COMPANY AudioMAXTM PRELIMINARY LX1710/1711 Class-D Mono Power Amplifier Controller IC Supply Voltage (PVDD, VDD)........................................................................................................................................................ -0.3V to 30V SLEEP, STATUS, FBK+, FBK- ............................................................................................................................................ -0.3V to V DD +0.3V IS- ...............................................................................................................................................................................PVDD -2 to PVDD to +0.3V RPWM, CPWM, MUTE ....................................................................................................................................................... -0.3V to V REF+0.3V INPUT +, INPUT -, INAMPOUT......................................................................................................................................... -0.3V to V REF+0.3V EAIN, EAOUT, FAOUT ...................................................................................................................................................... -0.3V to V REF+0.3V CLOCK ................................................................................................................................................................................... -0.3V to CN +0.3V Operating Junction Temperature Plastic (DB Package) .............................................................................................................................. 125 OC Storage Temperature Range ........................................................................................................................................................ -65 OC to 150 OC Lead Temperature (Soldering, 10 seconds).................................................................................................................................................300 OC Note 1: Exceeding these ratings could cause damage to the device. All voltages are with respect to Ground. Currents are positive into, negative out of the specified terminal. W W W .Microsemi .COM Unless otherwise specified, the following specifications apply over the operating ambient temperature 0C < TA < 70C. Test conditions: RPWM = 49.9k, CPWM = 100pF, VDD = PVDD = 15V Parameter Evaluation Module (See Figure 2) Supply Voltage LX1710 LX1711 Symbol Test Conditions LX1710 / 1711 Min Typ. Max 7 7 15 25 -70 25 Units VDD PSRR VIN = 15V, VRIPPLE = 1VRMS, 10Hz to 10kHz VIN = 15V, RL 10Hz to 22kHz VIN = 25V, RL 10Hz to 22kHz VIN = 15V, fIN = 1kHz, PO = 10W VIN = 15V, fIN = 1kHz, PO = 20W fIN = 1kHz, PO = 1W fIN = 20Hz to 20kHz, PO = 1W V dB Power Supply Rejection Ratio Output Power PO W 54 82 85 .05 .3 81 335 -110 110 3.4 1.6 0.6 1.0 1.5 5 60 7 % % dBV kHz A A V V % % % `mV dB `mHz V `mV A V/V V Page 3 Efficiency Total Harmonic Distortion Plus Noise Signal-To-Noise Ratio Oscillator Section Oscillator Frequency Charge Current Discharge Current Oscillator Peak Voltage Oscillator Valley Voltage Voltage Stability Temperature Stability Error Amplifier Input Offset Voltage DC Open Loop Gain Unity Gain Bandwidth High Output Voltage Low Output Voltage Input Common Mode Range Input Bias Current Input Amplifier Stage Gain Output Voltage, High Copyright (c) 2000 Rev. 1.1, 2000-12-01 THD+N SNR FOSC ICHG IDIS VPK VVAL (varies with VDD pin voltage) (varies with VDD pin voltage) (varies with VDD pin voltage) (varies with VDD pin voltage) VDD = 8V to 25V TA = 0OC to 70OC TA = -40OC to 125OC 2 2 E ELECTRICALS VIO AOL UGBW VOH VOL IIN IOUT = -100A IOUT = +100A VIN = 1V to VREF Set by Internal Resistors IOUT = -100A VREF -1 50 1 3.465 3.85 3.5 3.535 VOH Microsemi Linfinity Microelectronics Division 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 A MICROSEMI COMPANY AudioMAXTM PRELIMINARY LX1710/1711 Class-D Mono Power Amplifier Controller IC Parameter Output Voltage, Low Input Impedance Feedback Amplifier Stage Gain Input Impedance Current Limit Comparator Voltage Sense Threshold Blanking Pulse Delay Response Time IUM Pulses required to Current Limit Latch Consecutive Clear Pulses required to reset IUM counter Reference Voltage Section Initial Accuracy Voltage Stability Temperature Stability Line Regulation Load Regulation Under voltage Lockout Section Start Threshold Voltage UV Lockout Hysteresis UVLO Delay To Output Enable Supply Current Sleep Current Operating Current Sleep to Output Enable Sleep Threshold Mute Section Mute Threshold Output Drivers for N-Channel MOSFETs NFET Drivers, Low Level Voltage VOL ISINK = 3mA ISINK = 75mA ISOURCE = 3mA, CN = 5.2V applied externally ISOURCE = 75mA, CN = 5.2V applied externally ISINK = 3mA ISINK = 75mA ISOURCE = 3mA, CP = 5.2V (applied externally) ISOURCE = 75mA, CP = 5.2V (applied externally) LX1710 LX1711 W W W .Microsemi .COM Symbol VOL Test Conditions IOUT = +100A Min LX1710 / 1711 Typ. Max 1.3 42 Units `mV `k `mV/V `mV/V k Set by Internal Resistors Set by Internal Resistors 56 89 57 91 388 210 500 250 9 2 5.000 25 2 4 0.5 5 6.5 6.5 62,500 25 2.9 58 93 190 Excluding blanking pulse 9 2 230 mV `ns `ns `cycles `cycles 9 2 TA = 0OC to 70OC TA = -40OC to 125OC VDD = 9V to 15V IOUT = 0 to 20mA 50 5 10 `mV `mV `mV `mV `mV V V clkcyc A 0.5 SLEEP Input = 0V, TA = 25OC SLEEP Input = 2V, VIN = 15V, No MOSFETs connected 1.2 1.6 5.0 1.6 1.8 100 2.0 100 2.0 100 1.5 100 1.5 `mV clkcyc V V `mV V `mV V `mV V `mV V 62,500 1.45 1.7 30 1.5 30 1.5 30 1 30 1 NFET Drivers, High Level Voltage Output Drives For P-Channel MOSFETs VOH E ELECTRICALS PFET Drivers, Low Level Voltage VOL PFET Drivers, High Level Voltage VOH Copyright (c) 2000 Rev. 1.1, 2000-12-01 Microsemi Linfinity Microelectronics Division 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 4 A MICROSEMI COMPANY AudioMAXTM PRELIMINARY LX1710/1711 Class-D Mono Power Amplifier Controller IC LX1710/11 S IM P LIFIE D B LO C K D IA G R A M W W W .Microsemi .COM VDD 25 10 S LE E P 1 IS 27 PVDD + C LK VREF V 25 CN U V LO & REFERENCE 4 5V R eference 18 220m V C LO C K 28 RPW M CPW M 5 6 SYNC OSC 24 5V R eference 26 PVDD CP C U RR E N T S E N S E E A O UT 14 23 E A IN 13 F A U LT T IM E R ERROR AMP IN A M P O U T 9 S Q P+ OUTPUT D R IV E R S & LO G IC 22 N+ 21 N- IN P U T - 8 C LK R Q 20 P- MUTE IN P U T + 15 F A O U T M UX 7 IN P U T A M P MUTE 17 FBK- 16 FEEDBACK AMP M UT E 11 FBK+ - LX1710 Block Diagram Frequency Synchronization Two or more LX1710 / LX1711 oscillators can be configured for synchronous operation. One unit, the master, is programmed for the desired frequency with the RPWM and CPWM as usual. Additional units will be slave units, and their oscillators will be disabled by leaving the RPWM pin disconnected. The CLOCK pin and the CPWM pin of the slave units should be tied to the CLOCK pin and the CPWM pin of the master unit respectively. In this configuration, the CLOCK pins of the slave units begin receiving instead of transmitting clock pulses. Also, the CPWM pins quit driving the PWM capacitor in the slave units. Note that for optimum performance, all slave units should be located within a few inches of the master unit. Oscillator Configuration (RPWM and CPWM selection) The oscillator is programmed by the external timing components RPWM and CPWM. For a nominal frequency of 333kHz, RPWM and CPWM should be set to 49.9kOhms and 100pF respectively. Note that in order to keep the slope of the PWM ramp voltage proportional to the supply voltage, both the ramp peak and valley voltages, and the charge and discharge currents are proportional to the supply voltage. This keeps the frequency relatively constant while keeping the slope of the PWM ramp proportional to the voltage on the VDD pin. For operating frequencies other than 333kHz, the frequency can be approximated by the following equation: BLOCK DIAGRAM BLOCK DIAGRAM Frequency = 1 (0.577)( RPWM )(CPWM ) + 320ns Page 5 Copyright (c) 2000 Rev. 1.1, 2000-12-01 Microsemi Linfinity Microelectronics Division 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 A MICROSEMI COMPANY AudioMAXTM PRELIMINARY LX1710/1711 Class-D Mono Power Amplifier Controller IC W W W .Microsemi .COM V IN 7V to 15 V C9 0.1 F 35V + C 22 .1 F 25 24 VDD PV DD CLO C K 28 N C C 13 2.2 F + + C 11 4.7 F C 17 220 F 25V R S1 .0347 IS 26 5 CP RP W M CP W M 27 C 12 .1 F R 12 10 ohm Q1 L1 15 H P + 23 R 5 34.8K 6 C 16 100pF C1 1 F 1 4 VREF V 25 GND N+ 22 R 11 10 ohm Q2 C8 .1 F 50V R3 24.3K C7 220pF C 20 .68 F R 13 15 ohm 1W C 18 .47 F C2 1 F SLEEP 2 10 LX1710 P- 20 R6 10 ohm Q3 S LE E P C 21 .68 F C 19 .47 F M UT E 11 M UT E AU DIO INPU T R 8 10K C3 470nF NC 9 IN A M P O UT 7 IN P UT + N21 R 10 10 ohm Q4 L2 15 H C 26 330pF 8 R 9 10K C 14 470nF C5 18pF R 1 56.2K C4 150pF PG ND IN P UT NC CN 19 C 10 4.7 F R4 24.3K C6 220pF 3 + 18 16 17 12 NC 14 13 15 E A O UT E A IN FAOUT FBK+ FBKSTATUS R 2 10K - Typical Class-D Stereo Switching Amplifier Circuit Application APPLICATIONS APPLICATIONS Copyright (c) 2000 Rev. 1.1, 2000-12-01 Microsemi Linfinity Microelectronics Division 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 6 A MICROSEMI COMPANY AudioMAXTM PRELIMINARY LX1710/1711 Class-D Mono Power Amplifier Controller IC ! "# $ 100 50 20 10 5 2 THD + N (%) 1 0.5 0.23 0.1 0.04 0.01 0.005 0.002 0.001 20 ! "# % 100 50 20 10 5 2 THD + N (%) 1 0.5 0.26 0.1 0.04 0.02 0.01 0.005 0.002 W W W .Microsemi .COM 50 100 200 500 1.00k Frequency (Hz) 2k 5k 7.96k 10k 20k 0.001 50m 100m 200m 500m 1.13 2 Output Power (W ) 5 10 20 24.56 30 VIN = 15V RL PO =1 W RMS VIN = 15V fIN =1 kHz RL $ +20 +15 +10 % 50 45 40 35 Output Power (W) 30 25 20 15 10 5 20 50k 80k Voltage Amplification (dBr) +5 -0.08 -0.59 -5 -10 -15 -20 10 18.2 50 100 200 500 1k 2k 5k 10k 17.88k 50 100 200 500 Frequency (Hz) 1k 2k 5k 10k 20k Frequency (Hz) VIN = 15V RL PO = 1W RMS VIN = 15V THD+N = 1% GRAPHS GRAPHS Copyright (c) 2000 Rev. 1.1, 2000-12-01 Microsemi Linfinity Microelectronics Division 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 7 A MICROSEMI COMPANY AudioMAXTM PRELIMINARY LX1710/1711 Class-D Mono Power Amplifier Controller IC "# % 90% 85% 80% % "# " 60 50 Output Power (W) W W W .Microsemi .COM Efficency (%) 75% 70% 65% 60% 55% 50% 45% 0 5 10 15 Output Power (W) 40 30 20 10 20 25 30 0 6 11 16 Supply Voltage (VIN) 21 26 VIN = 15V fIN = 1kHz fIN = 1kHz RL THD+N = 1% +0 +0 -20 -20 -40 -40 -60 dBV -80 -92.57 -97.27 -120 dBV -140 20 50 100 200 500 .973k 2k 5k 10k 16.11k -60 -76.8 -100 -120 -140 20 Frequency (Hz) 50 100 200 500 1k 2k Frequency (Hz) 2.92k 5k 10k 20k VIN = 15V RL 10Hz - 22 kHz Bandwidth A - weighted VIN = 15V RL fIN = 1kHz VOUT = 1VRMS SNR = 81 dBV 10Hz - 22kHz Bandwidth A - weighted GRAPHS GRAPHS Copyright (c) 2000 Rev. 1.1, 2000-12-01 Microsemi Linfinity Microelectronics Division 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 8 A MICROSEMI COMPANY AudioMAXTM PRELIMINARY LX1710/1711 Class-D Mono Power Amplifier Controller IC E P W W W .Microsemi .COM 32 1 D F B H A L G C M A B C D E F G H L M P *LC &&'() *+,) 1.65 1.85 0.25 0.38 0.13 0.22 9.90 10.50 5.00 5.60 0.65 BSC 0.05 0.21 1.73 2.00 0.65 0.95 0 8 7.65 7.90 0.10 0.065 0.009 0.005 0.390 0.197 .0025 0.002 0.068 0.025 0 0.301 0.073 0.015 0.008 0.413 0.221 BSC 0.008 0.078 0.037 8 0.311 0.004 *Lead Coplanarity Note: 1. Dimensions do not include mold flash or protrusions; these shall not exceed 0.15mm (.006") on any side. Lead dimension shall not include solder coverage. MECHANICALS MECHANICALS Copyright (c) 2000 Rev. 1.1, 2000-12-01 Microsemi Linfinity Microelectronics Division 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 9 |
Price & Availability of LX1710 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |