|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
PRELIMINARY Integrated Circuit Systems, Inc. ICS8422002I-01 FEMTOCLOCKSTM CRYSTAL-TOLVHSTL FREQUENCY SYNTHESIZER FEATURES * Two LVHSTL outputs (VOHmax = 1.2V) * Selectable crystal oscillator interface or LVCMOS/LVTTL single-ended input * Supports the following output frequencies: 156.25MHz, 125MHz, 62.5MHz * VCO range: 560MHz - 680MHz * RMS phase jitter @ 156.25MHz, using a 25MHz crystal (1.875MHz - 20MHz): 0.44ps (typical) * Power supply modes: Core/Output 3.3V/1.8V 2.5V/1.8V * -40C to 85C ambient operating temperature GENERAL DESCRIPTION The ICS8422002I-01 is a 2 output LVHSTL Synthesizer optimized to generate Ethernet HiPerClockSTM reference clock frequencies and is a member of the HiPerClocksTM family of high performance clock solutions from ICS. Using a 25MHz 18pF parallel resonant crystal, the following frequencies can be generated based on the 2 frequency select pins (F_SEL[1:0]): 156.25MHz, 125MHz and 62.5MHz. The ICS8422002I-01 uses ICS' 3rd generation low phase noise VCO technology and can achieve 1ps or lower typical rms phase jitter, easily meeting Ethernet jitter requirements. The ICS8422002I-01 is packaged in a small 20-pin TSSOP package. ICS FREQUENCY SELECT FUNCTION TABLE M Divider Value 25 25 25 not used N Divider Value 4 5 10 Output Frequency (25MHz Ref.) 156.25 125 62.5 not used PIN ASSIGNMENT nc VDDO Q0 nQ0 MR nPLL_SEL nc VDDA F_SEL0 VDD 1 2 3 4 5 6 7 8 9 10 20 19 18 17 16 15 14 13 12 11 VDDO Q1 nQ1 GND VDD nXTAL_SEL TEST_CLK XTAL_IN XTAL_OUT F_SEL1 F_SEL1 F_SEL0 0 0 1 1 0 1 0 1 ICS8422002I-01 BLOCK DIAGRAM F_SEL[1:0] Pulldown nPLL_SEL Pulldown 2 20-Lead TSSOP 6.5mm x 4.4mm x 0.92mm package body G Package Top View Q0 F_SEL[1:0] 0 0 /4 0 1 /5 10 11 0 /10 Not Used TEST_CLK Pulldown 25MHz 1 nQ0 1 XTAL_IN OSC XTAL_OUT nXTAL_SEL Pulldown 0 Phase Detector VCO Q1 nQ1 M = 25 (fixed) MR Pulldown The Preliminary Information presented herein represents a product in prototyping or pre-production. The noted characteristics are based on initial product characterization. Integrated Circuit Systems, Incorporated (ICS) reserves the right to change any circuitry or specifications without notice. 8422002AGI-01 www.icst.com/products/hiperclocks.html REV. A MARCH 30, 2005 1 PRELIMINARY Integrated Circuit Systems, Inc. ICS8422002I-01 FEMTOCLOCKSTM CRYSTAL-TOLVHSTL FREQUENCY SYNTHESIZER Type Description No connect. Output supply pins. Differential output pair. LVHSTL interface levels. Active HIGH Master Reset. When logic HIGH, the internal dividers are reset causing the true outputs Qx to go low and the inver ted outputs nQx Pulldown to go high. When logic LOW, the internal dividers and the outputs are enabled. LVCMOS/LVTTL interface levels. Selects between the PLL and TEST_CLK as input to the dividers. When Pulldown LOW, selects PLL (PLL Enable). When HIGH, deselects the reference clock (PLL Bypass). LVCMOS/LVTTL interface levels. Analog supply pin. Pulldown Frequency select pins. LVCMOS/LVTTL interface levels. Core supply pin. Parallel resonant cr ystal interface. XTAL_OUT is the output, XTAL_IN is the input. Pulldown LVCMOS/LVTTL clock input. Selects between cr ystal or TEST_CLK inputs as the the PLL Reference Pulldown source. Selects XTAL inputs when LOW. Selects TEST_CLK when HIGH. LVCMOS/LVTTL interface levels. Power supply ground. Differential output pair. LVHSTL interface levels. TABLE 1. PIN DESCRIPTIONS Number 1, 7 2, 20 3, 4 5 Name nc VDDO Q0, nQ0 MR Unused Power Ouput Input 6 8 9, 11 10, 16 12, 13 14 15 17 18, 19 nPLL_SEL VDDA F_SEL0, F_SEL1 VDD XTAL_OUT, XTAL_IN TEST_CLK nXTAL_SEL GND nQ1, Q1 Input Power Input Power Input Input Input Power Output NOTE: Pulldown refers to internal input resistors. See Table 2, Pin Characteristics, for typical values. TABLE 2. PIN CHARACTERISTICS Symbol CIN RPULLDOWN Parameter Input Capacitance Input Pulldown Resistor Test Conditions Minimum Typical 4 51 Maximum Units pF k 8422002AGI-01 www.icst.com/products/hiperclocks.html 2 REV. A MARCH 30, 2005 PRELIMINARY Integrated Circuit Systems, Inc. ICS8422002I-01 FEMTOCLOCKSTM CRYSTAL-TOLVHSTL FREQUENCY SYNTHESIZER 4.6V -0.5V to VDD + 0.5V 50mA 100mA 73.2C/W (0 lfpm) -65C to 150C NOTE: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These ratings are stress specifications only. Functional operation of product at these conditions or any conditions beyond those listed in the DC Characteristics or AC Characteristics is not implied. Exposure to absolute maximum rating conditions for extended periods may affect product reliability. ABSOLUTE MAXIMUM RATINGS Supply Voltage, VDD Inputs, VI Outputs, IO Continuous Current Surge Current Package Thermal Impedance, JA Storage Temperature, TSTG TABLE 3A. POWER SUPPLY DC CHARACTERISTICS, VDD = VDDA = 3.3V5%, VDDO = 1.8V0.2V, TA = -40C TO 85C Symbol VDD VDDA VDDO IDD IDDA IDDO Parameter Core Supply Voltage Analog Supply Voltage Output Supply Voltage Power Supply Current Analog Supply Current Output Supply Current No Load Test Conditions Minimum 3.135 3.135 3.135 Typical 3.3 3.3 3.3 90 10 0 Maximum 3.465 3.465 3.465 Units V V V mA mA mA TABLE 3B. POWER SUPPLY DC CHARACTERISTICS, VDD = VDDA = 2.5V5%, VDDO = 1.8V0.2V, TA= -40C TO 85C Symbol VDD VDDA VDDO IDD IDDA IDDO Parameter Core Supply Voltage Analog Supply Voltage Output Supply Voltage Power Supply Current Analog Supply Current Output Supply Current No Load Test Conditions Minimum 2.375 2.375 2.375 Typical 2.5 2.5 2.5 80 10 0 Maximum 2.625 2.625 2.625 Units V V V mA mA mA TABLE 3C. LVCMOS / LVTTL DC CHARACTERISTICS, VDD = VDDA = 3.3V5% OR 2.5V5%, VDDO = 1.8V0.2V, TA= -40C TO 85C Symbol VIH VIL IIH Parameter Input High Voltage Input Low Voltage Input High Current Input Low Current TEST_CLK, MR, F_SEL0, F_SEL1, nPLL_SEL, nXTAL_SEL TEST_CLK, MR, F_SEL0, F_SEL1, nPLL_SEL, nXTAL_SEL Test Conditions VDD = 3.3V VDD = 2.5V VDD = 3.3V VDD = 2.5V VDD = VIN = 3.465 or 2.5V VDD = 3.465V or 2.5V, VIN = 0V -150 Minimum Typical 2 1. 7 -0.3 -0.3 Maximum VDD + 0.3 VDD + 0.3 0.8 0.7 150 Units V V V V A IIL A 8422002AGI-01 www.icst.com/products/hiperclocks.html 3 REV. A MARCH 30, 2005 PRELIMINARY Integrated Circuit Systems, Inc. ICS8422002I-01 FEMTOCLOCKSTM CRYSTAL-TOLVHSTL FREQUENCY SYNTHESIZER Test Conditions Minimum 1.0 0 40 0.6 Typical Maximum 1.2 0.4 60 1.1 Units V V % V TABLE 3D. LVHSTL DC CHARACTERISTICS, VDD = VDDA = 3.3V5%,VDDO = 1.8V0.2V, TA = -40C TO 85C Symbol VOH VOL VOX Parameter Output High Voltage; NOTE 1 Output Low Voltage; NOTE 1 Output Crossover Voltage; NOTE 2 Peak-to-Peak Output Voltage Swing VSWING NOTE 1: Outputs terminated with 50 to ground. NOTE 2: Defined with respect to output voltage swing at a given condition. TABLE 3E. LVHSTL DC CHARACTERISTICS, VDD = VDDA = 2.5V5%,VDDO = 1.8V0.2V, TA = -40C TO 85C Symbol VOH VOL VOX Parameter Output High Voltage; NOTE 1 Output Low Voltage; NOTE 1 Output Crossover Voltage; NOTE 2 40 0.9 Test Conditions Minimum 1.0 0.235 60 Typical Maximum 1.2 Units V V % V Peak-to-Peak Output Voltage Swing VSWING NOTE 1: Outputs terminated with 50 to ground. NOTE 2: Defined with respect to output voltage swing at a given condition. TABLE 4. CRYSTAL CHARACTERISTICS Parameter Mode of Oscillation Frequency Equivalent Series Resistance (ESR) Shunt Capacitance Drive Level NOTE: Characterized using an 18pF parallel resonant crystal. 22.4 Test Conditions Minimum Typical 25 Maximum 27.2 50 7 1 Units MHz pF mW Fundamental 8422002AGI-01 www.icst.com/products/hiperclocks.html 4 REV. A MARCH 30, 2005 PRELIMINARY Integrated Circuit Systems, Inc. ICS8422002I-01 FEMTOCLOCKSTM CRYSTAL-TOLVHSTL FREQUENCY SYNTHESIZER Test Conditions F_SEL[1:0] = 00 F_SEL[1:0] = 01 F_SEL[1:0] = 10 Minimum 14 0 11 2 56 TBD 156.25MHz, (1.875MHz - 20MHz) 0.44 0.48 0.49 410 125MHz, (1.875MHz - 20MHz) 62.5MHz,(1.875MHz - 20MHz) 20% to 80% Typical Maximum 17 0 136 68 Units MHz MHz MHz ps ps ps ps ps % TABLE 5A. AC CHARACTERISTICS, VDD = VDDA = 3.3V5%,VDDO = 1.8V0.2V, TA = -40C TO 85C Symbol fOUT Parameter Output Frequency Output Skew; NOTE 1, 3 RMS Phase Jitter (Random); NOTE 2 Output Rise/Fall Time tsk(o) tjit(O) tR / tF odc Output Duty Cycle 50 NOTE 1: Defined as skew between outputs at the same supply voltages and with equal load conditions. Measured at VDDO/2. NOTE 2: Please refer to the Phase Noise Plot. NOTE 3: This parameter is defined in accordance with JEDEC Standard 65. TABLE 5B. AC CHARACTERISTICS, VDD = VDDA = 2.5V5%,VDDO = 1.8V0.2V, TA = -40C TO 85C Symbol fOUT Parameter Output Frequency Output Skew; NOTE 1, 3 156.25MHz, (1.875MHz - 20MHz) RMS Phase Jitter (Random); NOTE 2 Output Rise/Fall Time 125MHz, (1.875MHz - 20MHz) 62.5MHz,(1.875MHz - 20MHz) tR / tF 20% to 80% Test Conditions F_SEL[1:0] = 00 F_SEL[1:0] = 01 F_SEL[1:0] = 10 Minimum 14 0 11 2 56 TBD 0.41 0.49 0.50 380 Typical Maximum 17 0 136 68 Units MHz MHz MHz ps ps ps ps ps % tsk(o) tjit(O) odc Output Duty Cycle 50 NOTE 1: Defined as skew between outputs at the same supply voltages and with equal load conditions. Measured at VDDO/2. NOTE 2 Please refer to the Phase Noise Plot. NOTE 3 This parameter is defined in accordance with JEDEC Standard 65. 8422002AGI-01 www.icst.com/products/hiperclocks.html 5 REV. A MARCH 30, 2005 PRELIMINARY Integrated Circuit Systems, Inc. ICS8422002I-01 FEMTOCLOCKSTM CRYSTAL-TOLVHSTL FREQUENCY SYNTHESIZER TYPICAL PHASE NOISE AT 156.25MHZ -10 -20 -30 -40 -50 -60 Ethernet Jitter Filter 156.25MHz RMS Phase Jitter (Random) 1.875MHz to 20MHz = 0.44ps (typical) 0 NOISE POWER dBc Hz -70 -80 -90 -100 -110 -120 -130 -140 -150 -170 -180 -190 100 1k 10k 100k 1M 10M 100M -160 Raw Phase Noise Data Phase Noise Result by adding Ethernet Filter to raw data OFFSET FREQUENCY (HZ) www.icst.com/products/hiperclocks.html 6 8422002AGI-01 REV. A MARCH 30, 2005 PRELIMINARY Integrated Circuit Systems, Inc. ICS8422002I-01 FEMTOCLOCKSTM CRYSTAL-TOLVHSTL FREQUENCY SYNTHESIZER PARAMETER MEASUREMENT INFORMATION 3.3V5% 1.8V0.2V 2.5V 5% 1.8V0.2V VDD, VDDA, VDDO Qx SCOPE VDD, VDDA, VDDO Qx SCOPE HSTL GND nQx HSTL GND nQx 0V 0V LVHSTL 3.3V/1.8V OUTPUT LOAD AC TEST CIRCUIT LVHSTL 2.5V/1.8V OUTPUT LOAD AC TEST CIRCUIT nQx Qx nQy Qy tsk(o) 80% Clock Outputs 80% VSW I N G 20% tR tF 20% OUTPUT SKEW OUTPUT RISE/FALL TIME Phase Noise Plot nQ0, nQ1 Q0, Q1 Pulse Width t Phase Noise Mask PERIOD Noise Power odc = f1 Offset Frequency f2 t PW t PERIOD RMS Jitter = Area Under the Masked Phase Noise Plot RMS PHASE JITTER 8422002AGI-01 OUTPUT DUTY CYCLE/PULSE WIDTH/PERIOD www.icst.com/products/hiperclocks.html 7 REV. A MARCH 30, 2005 PRELIMINARY Integrated Circuit Systems, Inc. ICS8422002I-01 FEMTOCLOCKSTM CRYSTAL-TOLVHSTL FREQUENCY SYNTHESIZER APPLICATION INFORMATION POWER SUPPLY FILTERING TECHNIQUES As in any high speed analog circuitry, the power supply pins are vulnerable to random noise. The ICS8422002I-01 provides separate power supplies to isolate any high switching noise from the outputs to the internal PLL. VDD, VDDA, and VDDO should be individually connected to the power supply plane through vias, and bypass capacitors should be used for each pin. To achieve optimum jitter performance, power supply isolation is required. Figure 1 illustrates how a 10 resistor along with a 10F and a .01F bypass capacitor should be connected to each VDDA. 3.3V or 2.5V VDD .01F VDDA .01F 10F 10 FIGURE 1. POWER SUPPLY FILTERING CRYSTAL INPUT INTERFACE The ICS8422002I-01 has been characterized with 18pF parallel resonant crystals. The capacitor values shown in Figure 2 below were determined using a 25MHz 18pF parallel resonant crystal and were chosen to minimize the ppm error. XTAL_OUT C1 22p X1 18pF Parallel Crystal XTAL_IN C2 22p ICS8422002I-01 Figure 2. CRYSTAL INPUt INTERFACE 8422002AGI-01 www.icst.com/products/hiperclocks.html 8 REV. A MARCH 30, 2005 PRELIMINARY Integrated Circuit Systems, Inc. ICS8422002I-01 FEMTOCLOCKSTM CRYSTAL-TOLVHSTL FREQUENCY SYNTHESIZER POWER CONSIDERATIONS This section provides information on power dissipation and junction temperature for the ICS8422002I-01. Equations and example calculations are also provided. 1. Power Dissipation. The total power dissipation for the ICS8422002I-01 is the sum of the core power plus the power dissipated in the load(s). The following is the power dissipation for VDD = 3.3V + 5% = 3.465V, which gives worst case results. NOTE: Please refer to Section 3 for details on calculating power dissipated in the load. * * Power (core)MAX = VDD_MAX * IDD_MAX = 3.465V * 100mA = 346.5mW Power (outputs)MAX = 32.8mW/Loaded Output pair If all outputs are loaded, the total power is 2 * 32.8mW = 65.6mW Total Power_MAX (3.465V, with all outputs switching) = 346.5mW + 65.6mW = 412.1mW 2. Junction Temperature. Junction temperature, Tj, is the temperature at the junction of the bond wire and bond pad and directly affects the reliability of the device. The maximum recommended junction temperature for HiPerClockSTM devices is 125C. The equation for Tj is as follows: Tj = JA * Pd_total + TA Tj = Junction Temperature JA = Junction-to-Ambient Thermal Resistance Pd_total = Total Device Power Dissipation (example calculation is in section 1 above) TA = Ambient Temperature In order to calculate junction temperature, the appropriate junction-to-ambient thermal resistance JA must be used. Assuming a moderate air flow of 200 linear feet per minute and a multi-layer board, the appropriate value is 66.6C/W per Table 6 below. Therefore, Tj for an ambient temperature of 85C with all outputs switching is: 85C + 0.412W * 66.6C/W = 112.4C. This is well below the limit of 125C. This calculation is only an example. Tj will obviously vary depending on the number of loaded outputs, supply voltage, air flow, and the type of board (single layer or multi-layer). TABLE 6. THERMAL RESISTANCE JA FOR 20-PIN TSSOP, FORCED CONVECTION JA by Velocity (Linear Feet per Minute) 0 Single-Layer PCB, JEDEC Standard Test Boards Multi-Layer PCB, JEDEC Standard Test Boards 114.5C/W 73.2C/W 200 98.0C/W 66.6C/W 500 88.0C/W 63.5C/W NOTE: Most modern PCB designs use multi-layered boards. The data in the second row pertains to most designs. 8422002AGI-01 www.icst.com/products/hiperclocks.html 9 REV. A MARCH 30, 2005 PRELIMINARY Integrated Circuit Systems, Inc. ICS8422002I-01 FEMTOCLOCKSTM CRYSTAL-TOLVHSTL FREQUENCY SYNTHESIZER 3. Calculations and Equations. The purpose of this section is to derive the power dissipated into the load. LVHSTL output driver circuit and termination are shown in Figure 3. VDDO Q1 VOUT RL 50 FIGURE 3. LVHSTL DRIVER CIRCUIT AND TERMINATION To calculate worst case power dissipation into the load, use the following equations which assume a 50 load. Pd_H is power dissipation when the output drives high. Pd_L is the power dissipation when the output drives low. Pd_H = (V OH_MAX /R ) * (V L DD_MAX -V OH_MAX ) ) Pd_L = (V OL_MAX /R ) * (V L DD_MAX -V OL_MAX Pd_H = (1V/50) * (2V - 1V) = 20mW Pd_L = (0.4V/50) * (2V - 0.4V) = 12.8mW Total Power Dissipation per output pair = Pd_H + Pd_L = 32.8mW 8422002AGI-01 www.icst.com/products/hiperclocks.html 10 REV. A MARCH 30, 2005 PRELIMINARY Integrated Circuit Systems, Inc. ICS8422002I-01 FEMTOCLOCKSTM CRYSTAL-TOLVHSTL FREQUENCY SYNTHESIZER RELIABILITY INFORMATION TABLE 7. JAVS. AIR FLOW TABLE FOR 20 LEAD TSSOP JA by Velocity (Meters per Second) 0 Single-Layer PCB, JEDEC Standard Test Boards Multi-Layer PCB, JEDEC Standard Test Boards 114.5C/W 73.2C/W 200 98.0C/W 66.6C/W 500 88.0C/W 63.5C/W NOTE: Most modern PCB designs use multi-layered boards. The data in the second row pertains to most designs. TRANSISTOR COUNT The transistor count for ICS8422002I-01 is: 2951 8422002AGI-01 www.icst.com/products/hiperclocks.html 11 REV. A MARCH 30, 2005 PRELIMINARY Integrated Circuit Systems, Inc. ICS8422002I-01 FEMTOCLOCKSTM CRYSTAL-TOLVHSTL FREQUENCY SYNTHESIZER 20 LEAD TSSOP PACKAGE OUTLINE - G SUFFIX FOR TABLE 8. PACKAGE DIMENSIONS SYMBOL MIN N A A1 A2 b c D E E1 e L aaa 0.45 0 -4.30 0.65 BASIC 0.75 8 0.10 -0.05 0.80 0.19 0.09 6.40 6.40 BASIC 4.50 20 1.20 0.15 1.05 0.30 0.20 6.60 Millimeters MAX Reference Document: JEDEC Publication 95, MO-153 8422002AGI-01 www.icst.com/products/hiperclocks.html 12 REV. A MARCH 30, 2005 PRELIMINARY Integrated Circuit Systems, Inc. ICS8422002I-01 FEMTOCLOCKSTM CRYSTAL-TOLVHSTL FREQUENCY SYNTHESIZER Marking ICS22002AI01 ICS22002AI01 Package 20 Lead TSSOP 20 Lead TSSOP Shipping Packaging tube 2500 tape & reel Temperature -40C to 85C -40C to 85C TABLE 9. ORDERING INFORMATION Part/Order Number ICS8422002AGI-01 ICS8422002AGI-01T The aforementioned trademark, HiPerClockSTM and FEMTOCLOCKSTM is a trademark of Integrated Circuit Systems, Inc. or its subsidiaries in the United States and/or other countries. While the information presented herein has been checked for both accuracy and reliability, Integrated Circuit Systems, Incorporated (ICS) assumes no responsibility for either its use or for infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial and industrial applications. Any other applications such as those requiring high reliability or other extraordinary environmental requirements are not recommended without additional processing by ICS. ICS reserves the right to change any circuitry or specifications without notice. ICS does not authorize or warrant any ICS product for use in life support devices or critical medical instruments. 8422002AGI-01 www.icst.com/products/hiperclocks.html 13 REV. A MARCH 30, 2005 |
Price & Availability of ICS8422002I-01 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |