View 5818-F_292581.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

5818-F 32-BIT SERIAL-INPUT, LATCHED SOURCE DRIVERS FOR -40C TO +85C OPERATION
5818-F
Designed primarily for use with vacuum-fluorescent displays, the UCQ5818AF and UCQ5818EPF smart power BiMOS II drivers combine CMOS shift registers, data latches, and control circuitry, with bipolar high-speed sourcing outputs and DMOS active pull-down circuitry. The high-speed shift register and data latches allow direct interfacing with microprocessor LSI-based systems. A CMOS serial data output enables cascade connections in applications requiring additional drive lines. Both devices feature 60 V and -40 mA output ratings, allowing them to be used in many other peripheral power driver applications. These smart power drivers have been designed with BiMOS II logic for improved data entry rates. With a 5 V supply, they will typically operate above 5 MHz. At 12 V, significantly higher speeds are obtained. Use of these devices with TTL may require the use of appropriate pull-up resistors to ensure an input logic high. All devices can be operated over the ambient temperature range of -40C to +85C. The UCQ5818AF is supplied in a 40-pin plastic dual in-line package with 0.600" (15.24 mm) row spacing. A copper lead frame, reduced supply current requirement, and low output saturation voltage permits operation with minimum junction temperature rise. The `A' package allows all 32 outputs to be operated at -25 mA continuously over the operating temperature range. For high-density packaging applications, the UCQ5818EPF is furnished in a 44-lead plastic chip carrier (quad pack) for surface mounting on solder lands with 0.050" (1.27 mm) centers. The PLCC allows -25 mA continuous operation of all outputs simultaneously at ambient temperatures to 60C. Similar devices are available as the UCQ5810AF/LWF (10 bits), UCQ5811A (12 bits), and UCQ5812AF/ EPF (20 bits).
Data Sheet 26182.29*
BiMOS II 32-BIT SERIAL-INPUT, LATCHED SOURCE DRIVERS FOR -40C TO +85C OPERATION
UCQ5818EPF
SERIAL DATA OUT LOAD SUPPLY LOGIC SUPPLY SERIAL DATA IN OUT30 OUT31 OUT32 OUT 1 OUT 2 41 NC OUT3 40
44
43
V DD
VBB
42
6
3
5
4
2
1
OUT29
7 8 9 10 REGISTER REGISTER LATCHES
2
39 38 37 36
OUT 4
LATCHES
11 12 13 14 15 16 OUT19 17
35 34 33 19 32 31 30 29 OUT13 NC
OUT 8
BLNK
CLK
20
ST
27 OUT14
18
23
19
24
25
21
22
OUT17
BLANKING
GROUND
STROBE
OUT15
NC
OUT18
OUT 16
26
CLOCK
NC
28
Dwg. PP-059-2
ABSOLUTE MAXIMUM RATINGS
at TA = 25C
Logic Supply Voltage, VDD .................... 15 V Driver Supply Voltage, V BB ................... 60 V Continuous Output Current, IOUT ......................... -40 mA to +15 mA Input Voltage Range, VIN ....................... -0.3 V to VDD + 0.3 V Package Power Dissipation, PD (UCQ5818AF) ............................ 3.5 W* (UCQ5818EPF) ......................... 2.7 W Operating Temperature Range, TA ................................. -40C to +85C Storage Temperature Range, TS ............................... -55C to +150C
* Derate at rate of 28 mW/C above TA = +25C Derate at rate of 22 mW/C above TA = +25C
FEATURES
s s s s s 60 V Source Outputs High-Speed Source Drivers To 3.3 MHz Data Input Rate Low-Output Saturation Voltages Active DMOS Pull-Downs s Low-Power CMOS Logic and Latches s Reduced Supply Current Requirements s Improved Replacements for SN75518N/FN
Caution: CMOS devices have input static protection but are susceptible to damage when exposed to extremely high static electrical charges.
Always order by complete part number, e.g., UCQ5818EPF .
5818-F 32-BIT SERIAL-INPUT, LATCHED SOURCE DRIVERS FOR -40C TO +85C OPERATION
UCQ5818AF FUNCTIONAL BLOCK DIAGRAM
LOAD SUPPLY SERIAL DATA OUT OUT 32 OUT 31 OUT 30 OUT 29 OUT 28 OUT 27 OUT 26 OUT 25 OUT 24 OUT 23 OUT 22 OUT 21 OUT 20 OUT 19 OUT 18 OUT 17 BLANKING GROUND 1 2 3 4 5 6 7 8 9
REGISTER REGISTER LATCHES LATCHES
VBB
VDD
40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23
LOGIC SUPPLY SERIAL DATA IN OUT 1 OUT 2 OUT 3 OUT 4 OUT 5 OUT 6 OUT 7 OUT 8 OUT 9
CLOCK SERIAL DATA IN STROBE
V DD
LOGIC SUPPLY SERIAL DATA OUT
SERIAL-PARALLEL SHIFT REGISTER
LATCHES
BLANKING MOS BIPOLAR LOAD SUPPLY
10 11 12 13 14 15 16 17 18 19 20 BLNK
VBB
GROUND
OUT 10 OUT 11 OUT 12 OUT 13 OUT 14 OUT 15 OUT 16 STROBE CLOCK
OUT 1 OUT 2 OUT 3
OUT N
Dwg. FP-013-1
TYPICAL INPUT CIRCUIT
VDD
ST CLK
22 21
IN
Dwg. PP-029-4
3.0
ALLOWABLE PACKAGE POWER DISSIPATION IN WATTS
2.5
Dwg. EP-010-5
SUFFIX 'A', R
JA
= 36C/W
TYPICAL OUTPUT DRIVER
2.0
V BB
1.5
SUFFIX 'EP', RJA = 46C/W
1.0
OUT N
0.5
0 25 50 75 100 125 AMBIENT TEMPERATURE IN C 150
Dwg. No. A-14,219
Dwg. GP-025A
115 Northeast Cutoff, Box 15036 W Worcester, Massachusetts 01615-0036 (508) 853-5000 Copyright (c) 1988, 1995, Allegro MicroSystems, Inc.
5818-F 32-BIT SERIAL-INPUT, LATCHED SOURCE DRIVERS FOR -40C TO +85C OPERATION
ELECTRICAL CHARACTERISTICS over operating temperature range, VBB = 60 V unless otherwise noted.
Limits @ VDD = 5 V Characteristic Output Leakage Current Output Voltage Symbol ICEX VOUT(1) VOUT(0) Test Conditions VOUT = 0 V, TA = +70C IOUT = -25 mA IOUT = 1 mA IOUT = 2 mA Output Pull-Down Current IOUT(0) VOUT = 5 V to VBB VOUT = 20 V to VBB Input Voltage VIN(1) VIN(0) Input Current IIN(1) IIN(0) Serial Data Output Voltage VOUT(1) VOUT(0) Maximum Clock Frequency Supply Current fclk IDD(1) IDD(0) IBB(1) IBB(0) Blanking to Output Delay tPHL tPLH Output Fall Time Output Rise Time tf tr All Outputs High All Outputs Low Outputs High, No Load Outputs Low CL = 30 pF, 50% to 50% CL = 30 pF, 50% to 50% CL = 30 pF, 90% to 10% CL = 30 pF, 10% to 90% VIN = VDD VIN = 0.8 V IOUT = -200 A IOUT = 200 A Mln. -- 58 -- -- 2.0 -- 3.5 -0.3 -- -- 4.5 -- 3.3 -- -- -- -- -- -- -- -- Typ. -5.0 58.5 2.0 -- 3.5 -- -- -- 0.05 -0.05 4.7 200 5.0 100 100 3.0 10 2000 1000 1450 650 Max. -15 -- 3.0 -- -- -- 5.3 +0.8 0.5 -0.5 -- 250 -- 300 300 6.0 100 -- -- -- -- Limits @ VDD = 12 V Min. -- 58 -- -- -- 8.0 10.5 -0.3 -- -- 11.7 -- -- -- -- -- -- -- -- -- -- Typ. -5.0 58.5 -- 2.0 -- 13 -- -- 0.1 -0.1 11.8 100 7.5 200 200 3.0 10 1000 850 650 700 Max. -15 -- -- 3.5 -- -- 12.3 +0.8 1.0 -1.0 -- 200 -- 500 500 6.0 100 -- -- -- -- Units A V V V mA mA V V A A V mV MHz A A mA A ns ns ns ns
Negative current is defined as coming out of (sourcing) the specified device terminal.
5818-F 32-BIT SERIAL-INPUT, LATCHED SOURCE DRIVERS FOR -40C TO +85C OPERATION
Serial Data present at the input is transferred to the shift register on the logic "0" to logic "1" transition of the CLOCK input pulse. On succeeding CLOCK pulses, the registers shift data information towards the SERIAL DATA OUTPUT. The SERIAL DATA must appear at the input prior to the rising edge of the CLOCK input waveform. Information present at any register is transferred to the respective latch when the STROBE is high (serial-to-parallel conversion). The latches will continue to accept new data as long as the STROBE is held high. Applications where the latches are bypassed (STROBE tied high) will require that the BLANKING input be high during serial data entry. When the BLANKING input is high, the output source drivers are disabled (OFF); the DMOS sink drivers are ON, the information stored in the latches is not affected by the BLANKING input. With the BLANKING input low, the outputs are controlled by the state of their respective latches.
CLOCK DATA IN
A
B
D
E C
F
STROBE BLANKING G OUTN
Dwg. No. A-12,649A
TIMING CONDITIONS
(TA = +25C, V DD = 5.0 V, Logic Levels are VDD and Ground)
A. Minimum Data Active Time Before Clock Pulse (Data Set-Up Time) ............................................................................... 75 ns B. Minimum Data Active Time After Clock Pulse (Data Hold Time) ................................................................................... 75 ns C. Minimum Data Pulse Width ................................................................. 150 ns D. Minimum Clock Pulse Width ............................................................... 150 ns E. Minimum Time Between Clock Activation and Strobe ........................ 300 ns F. Minimum Strobe Pulse Width .............................................................. 100 ns G. Typical Time Between Strobe Activation and Output Transition ................................................................................. 500 ns
TRUTH TABLE
Serial Shift Register Contents Data Clock Input Input I1 I2 I3 ... IN-1 IN H L X H L R1 R2 ... R1 R2 ... RN-2 RN-1 RN-2 RN-1 RN-1 RN X X Serial Data Strobe Output Input RN-1 RN-1 RN X PN L H R1 R2 R3 ... P1 P2 P3 ... X
L = Low Logic Level H = High Logic Level X = Irrelevant
Latch Contents I1 I2 I3 ... IN-1 IN Blanking
Output Contents I1 I2 I3 ... IN-1 I N
R1 R2 R3 ... X X X ...
RN-1 RN PN-1 PN X X L H P1 P2 P3 ... PN-1 PN L L L ... L L
P1 P2 P3 ...
PN-1 PN
X
X
...
P = Present State
R = Previous State
115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000
5818-F 32-BIT SERIAL-INPUT, LATCHED SOURCE DRIVERS FOR -40C TO +85C OPERATION
UCQ5818AF
Dimensions in Inches (controlling dimensions)
40 0.015 0.008 21
0.700
MAX
0.580 0.485
0.600
BSC
1
2 0.070 0.030
3
4 2.095 1.980
20 0.100
BSC
0.005
MIN
0.250
MAX
0.015
MIN
0.200 0.115 0.022 0.014
Dwg. MA-003-40 in
Dimensions in Millimeters (for reference only)
40 0.381 0.204 21
17.78 14.73 12.32
MAX
15.24
BSC
1
2 1.77 0.77
3
4 53.2 50.3
2.54
BSC
20
0.13
MIN
6.35
MAX
0.39
MIN
5.08 2.93 0.558 0.356
Dwg. MA-003-40 mm
NOTES: 1. Exact body and lead configuration at vendor's option within limits shown. 2. Lead spacing tolerance is non-cumulative. 3. Lead thickness is measured at seating plane or below.
5818-F 32-BIT SERIAL-INPUT, LATCHED SOURCE DRIVERS FOR -40C TO +85C OPERATION
UCQ5818EPF
Dimensions in Inches (contrrolling dimensions)
28 18
29 0.319 0.291 0.021 0.013 0.695 0.685 0.656 0.650 0.319 0.291 0.050
BSC INDEX AREA
17
0.032 0.026
39
7
40 0.020
MIN
44
1
2
6
0.656 0.650 0.695 0.685
Dwg. MA-005-44A in
0.180 0.165
Dimensions in Millimeters (for reference only)
28 18
29 8.10 7.39 0.533 0.331 17.65 17.40 16.662 16.510
INDEX AREA
17
0.812 0.661
8.10 7.39 1.27
BSC
39
7
40 0.51
MIN
44
1
2
6
4.57 4.20
16.662 16.510 17.65 17.40
Dwg. MA-005-44A mm
NOTES: 1. Exact body and lead configuration at vendor's option within limits shown. 2. Lead spacing tolerance is non-cumulative.
115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000
5818-F 32-BIT SERIAL-INPUT, LATCHED SOURCE DRIVERS FOR -40C TO +85C OPERATION
This page intentionally left blank
5818-F 32-BIT SERIAL-INPUT, LATCHED SOURCE DRIVERS FOR -40C TO +85C OPERATION
BiMOS II (Series 5800) & DABiC IV (Series 6800) INTELLIGENT POWER INTERFACE DRIVERS SELECTION GUIDE
Function
8-Bit (saturated drivers) 8-Bit 8-Bit 8-Bit 8-Bit 9-Bit 10-Bit (active pull-downs) 12-Bit (active pull-downs) 20-Bit (active pull-downs) 32-Bit (active pull-downs) 32-Bit 32-Bit (saturated drivers)
Output Ratings *
SERIAL-INPUT LATCHED DRIVERS -120 mA 350 mA 350 mA 350 mA 350 mA 1.6 A -25 mA -25 mA -25 mA -25 mA 100 mA 100 mA 50 V 50 V 80 V 50 V 80 V 50 V 60 V 60 V 60 V 60 V 30 V 40 V
Part Number
5895 5821 5822 5841 5842 5829 5810-F and 6809/10 5811 and 6811 5812-F and 6812 5818-F and 6818 5833 5832
PARALLEL-INPUT LATCHED DRIVERS 4-Bit 8-Bit 8-Bit 350 mA -25 mA 350 mA 50 V 60 V 50 V 5800 5815 5801
SPECIAL-PURPOSE FUNCTIONS Unipolar Stepper Motor Translator/Driver Addressable 28-Line Decoder/Driver
*
1.25 A 450 mA
50 V 30 V
5804 6817
Current is maximum specified test condition, voltage is maximum rating. See specification for sustaining voltage limits. Negative current is defined as coming out of (sourcing) the output. Complete part number includes additional characters to indicate operating temperature range and package style. Internal transient-suppression diodes included for inductive-load protection.
Allegro MicroSystems, Inc. reserves the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the design of its products. The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, Inc. assumes no responsibility for its use; nor for any infringements of patents or other rights of third parties which may result from its use.
115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000

▲Up To Search▲

Price & Availability of 5818-F

	To Download 5818-F Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .