|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
To Top / Lineup / Index FUJITSU SEMICONDUCTOR DATA SHEET DS05-11154-1E MEMORY Registered 16 M x 72 BIT SYNCHRONOUS DYNAMIC RAM DIMM MB8516SR72CA-102/-103/-102L/-103L 168-pin, 4 Clock, 1-bank, based on 16 M x 4 Bit SDRAMs with SPD s DESCRIPTION The Fujitsu MB8516SR72CA is a fully decoded, CMOS Synchronous Dynamic Random Access Memory (SDRAM) Module consisting of eighteen MB81F64442C devices which organized as four banks of 16 M x 4 bits and a 2K-bit serial EEPROM on a 168-pin glass-epoxy substrate. The MB8516SR72CA features a fully synchronous operation referenced to a positive edge clock whereby all operations are synchronized at a clock input which enables high performance and simple user interface coexistence. The MB8516SR72CA is optimized for those applications requiring high speed, high performance and large memory storage, and high density memory organizations. This module is ideally suited for server system, workstations, high-end PCs, and other applications where enhanced performance is needed. s PRODUCT LINE & FEATURES Parameter CL-tRCD-tRP Clock Frequency Burst Mode Cycle Time Output Valid from Clock Power Dissipation MB8516SR72CA-102/-102L MB8516SR72CA-103/-103L 2-2-2 clk min. 3-2-2 clk min. 100 MHz max. 100 MHz max. 10ns min. 15ns min. 10ns min. 10ns min. 6 ns 8 ns 6 ns 6 ns 13540 mW max. 495 mW max. (Std. power) 455 mW max. (Low power) Registered Mode Registered Mode Two Banks Active Self Refresh Mode CL = 2* CL = 3* CL = 2* CL = 3* Note * : For registered mode, actual CAS Latency is added one cycle to the CAS Latency of device because of a delay by registers. * Registered 168-pin DIMM Socket Type * 4096 Refresh Cycle every 65.6 ms (Lead pitch: 1.27 mm) * Auto and Self Refresh * Conformed to JEDEC Standard * CKE Power Down Mode * Organization: 16,777,216 words x 72 bits * DQM Byte Masking (Read/Write) * Memory: MB81F64442C (16 M x 4, 4-bank) x 18 pcs * Serial Presence Detect (SPD) with Serial EEPROM: * 3.3 V 0.3 V Supply Voltage Intel SPD spec Rev 1.2A Format * All input/output LVTTL compatible * Module size: * Conformed to Intel PC/100 spec 1.70" (height) x 5.25" (length) x 0.32" (thickness) To Top / Lineup / Index MB8516SR72CA-102/-103/-102L/-103L s PACKAGE 168-pin plastic DIMM (socket type) Under development (MDS-168P-P43) Package and Ordering Information - 168-pin DIMM, order as MB8516SR72CA-xxxDG (DG = Std. power ver., Gold pad) MB8516SR72CA-xxxLDG (LDG = Low power ver., Gold pad) 2 To Top / Lineup / Index MB8516SR72CA-102/-103/-102L/-103L s PIN ASSIGNMENTS Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 Signal Name VSS DQ0 DQ1 DQ2 DQ3 VCC DQ4 DQ5 DQ6 DQ7 DQ8 VSS DQ9 DQ10 DQ11 DQ12 DQ13 VCC DQ14 DQ15 CB0 CB1 VSS N.C. N.C. VCC WE DQMB0 Pin No. 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 Signal Name DQMB1 S0 N.C. VSS A0 A2 A4 A6 A8 A10 BA1 VCC VCC CLK0 VSS N.C. S2 DQMB2 DQMB3 N.C. VCC N.C. N.C. CB2 CB3 VSS DQ16 DQ17 Pin No. 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 Signal Name DQ18 DQ19 VCC DQ20 N.C. N.C. N.C. VSS DQ21 DQ22 DQ23 VSS DQ24 DQ25 DQ26 DQ27 VCC DQ28 DQ29 DQ30 DQ31 VSS CLK2 N.C. N.C. (WP) SDA SCL VCC Pin No. 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 Signal Name VSS DQ32 DQ33 DQ34 DQ35 VCC DQ36 DQ37 DQ38 DQ39 DQ40 VSS DQ41 DQ42 DQ43 Pin No. Signal Name Pin No. Signal Name 113 DQMB5 114 N.C. 115 RAS 116 VSS 117 A1 118 A3 119 A5 120 A7 121 A9 122 BA0 123 A11 124 VCC 125 CLK1 126 N.C. 127 VSS 128 CKE0 129 N.C. 130 DQMB6 131 DQMB7 132 N.C. 133 VCC 134 N.C. 135 N.C. 136 CB6 137 CB7 138 VSS 139 DQ48 140 DQ49 141 DQ50 142 DQ51 143 VCC 144 DQ52 145 N.C. 146 N.C. 147 REGE 148 VSS 149 DQ53 150 DQ54 151 DQ55 152 VSS 153 DQ56 154 DQ57 155 DQ58 156 DQ59 157 VCC 158 DQ60 159 DQ61 160 DQ62 161 DQ63 162 VSS 163 CLK3 164 N.C. 165 SA0 166 SA1 167 SA2 168 VCC 100 DQ44 101 DQ45 102 VCC 103 DQ46 104 DQ47 105 CB4 106 CB5 107 VSS 108 N.C. 109 N.C. 110 VCC 111 CAS 112 DQMB4 3 To Top / Lineup / Index MB8516SR72CA-102/-103/-102L/-103L TOP VIEW 133.35 mm D2 D0 43.18 mm Reg. D 18 1 10 11 D1 D3 D4 D5 D6 D7 D8 PLANE 0 Reg. D 19 40 41 PLL D 20 D 21 84 85 94 95 124 125 168 PLANE 1 D9 D 10 D 11 D 12 D 13 D 14 D 15 D 16 D 17 (MDS-168P-P43) s PIN DESCRIPTIONS Symbol A0 to A11 BA0, BA1 RAS CAS WE CLK0 to CLK3 CKE0 S0, S2 REGE *1 I/O I I I I I I I I I I Function Address Input Bank Select (Bank Address) Row Address Strobe Column Address Strobe Write Enable Clock Input Clock Enable Chip Select Register Enable Data (DQ) Mask Symbol DQ0 to DQ63 CB0 to CB7 VCC VSS N.C. SA0 to SA2 SCL SDA WP I/O Function I/O Data Input/Data Output I/O ECC Data Input/Output -- -- -- I I I/O I Power Supply (+3.3 V) Ground (0 V) No Connection Serial PD Address Input Serial PD Clock Serial PD Address & Data Input/Output Serial PD Write Protect -- DQMB0 to DQMB7 Notes: *1. REGE pin is to switch the module function mode to Registered Mode, or Buffered Mode. For Registered Mode function, REGE = VIH. 4 To Top / Lineup / Index MB8516SR72CA-102/-103/-102L/-103L s SERIAL-PD INFORMATION Byte 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 to 61 62 63 64 to 71 72 73 to 90 91 to 92 93 to 94 95 to 98 99 to 125 126 127 128+ Function Described 128 Byte Defines Number of Bytes Written into Serial Memory at Module Manufacture 256 Byte Total Number of Bytes of SPD Memory Device SDRAM Fundamental Memory Type 12 Number of Row Addresses 10 Number of Column Addresses 1 bank Number of Module Banks 72 bit Data Width +0 Data Width (Continuation) LVTTL Interface Type 10 / 10 ns SDRAM Cycle Time (Highest CAS Latency) 6 / 6 ns SDRAM Access from Clock (Highest CAS Latency) ECC DIMM Configuration Type Self, Normal Refresh Rate/Type Primary SDRAM Width x4 Error Checking SDRAM Width x4 1 Cycle Minimum Clock Delay for Back to Back Random Column Addresses 1, 2, 4, 8, Page Burst Lengths Supported 4 bank Number of Banks on Each SDRAM Device 2, 3 CAS Latency Supported 0 CS Latency 0 Write Latency Registered SDRAM Module Attributes *1 SDRAM Device Attributes : General 10 / 15 ns SDRAM Cycle Time (2nd. Highest CAS Latency) 6 / 8 ns SDRAM Access from Clock (2nd. Highest CAS Latency) No Support SDRAM Cycle Time (3rd. Highest CAS Latency) No Support SDRAM Access from Clock (3rd. Highest CAS Latency) 20 / 20 ns Minimum Row Precharge Time (tRP) Row Activate to Row Activate Minimum (tRRD) 20 / 20 ns RAS to CAS Delay Min. (tRCD) 20 / 20 ns Minimum RAS Pulse Width 50 / 50 ns Module Bank Density 128 MByte Command and Address Signal Input Setup Time 2 ns Command and Address Signal Input Hold Time 1 ns Data Signal Input Setup Time 2 ns Data Signal Input Hold Time 1 ns Unused Storage Locations -- SPD Data Revision Code 1.2 Checksum for Byte 0 to 62 *2 Manufacturer's JEDEC ID Code Per JEP-108E Optional Manufacturing Location Optional Manufacturer's Part Number Optional Revision Code Optional Manufacturing Data Optional Assembly Serial Number Optional Manufacturer Specific Data Optional Intel Specification Frequency 100 MHz Intel Specification Details for 100 MHz Support CL = 2, 3 / 3 Unused Storage Locations -- Hex Value -102/- -103/102L 103L 80h 80h 08h 04h 0Ch 0Ah 01h 48h 00h 01h A0h 60h 02h 80h 04h 04h 01h 8Fh 04h 06h 01h 01h 1Fh 0Eh A0h 60h 00h 00h 14h 14h 14h 32h 20h 20h 10h 20h 10h 00h 12h 3Fh 00h 00h 00h 00h 00h 00h 00h 64h 8Fh -- 08h 04h 0Ch 0Ah 01h 48h 00h 01h A0h 60h 02h 80h 04h 04h 01h 8Fh 04h 06h 01h 01h 1Fh 0Eh F0h 80h 00h 00h 14h 14h 14h 32h 20h 20h 10h 20h 10h 00h 12h AFh 00h 00h 00h 00h 00h 00h 00h 64h 8Dh -- Note: Any write operation must NOT be executed into the addresses of Byte 0 to Byte 127. Some or all data stored into Byte 0 to Byte 127 may be broken. *1. Byte 22: SDRAM Device Attributes Bit7 Bit6 Bit5 TBD TBD Upper VCC tolerance Bit4 Bit3 Supports Write 1 /Read Burst 1 Bit2 Supports Precharge All 1 Bit1 Supports AutoPrecharge 1 Bit0 Supports Early RAS Precharge 0 Lower VCC tolerance 0 0 0 0 *2. Byte 63: Checksum for Byte 0 to 62 This byte is the checksum for Byte 0 through 62. This byte contains the value of the low 8-bits of the arithmetic sum of Byte 0 through 62. 5 To Top / Lineup / Index MB8516SR72CA-102/-103/-102L/-103L BLOCK DIAGRAM S0, S2 DQMB0 to DQMB7 BA0, BA1 A0 to A11 RAS CAS WE CKE0 10 K VCC REGE CLK0 CLK D 20 FBIN FBOUT VSS RS0 RDQMB0 10 DQ (0:3) 10 DQ (4:7) RDQMB1 10 DQ (8:11) 10 DQ (12:15) 10 CB (0:3) DQM DQ (0:3) DQM DQ (0:3) CS D2 CS D3 CS D4 CB (4:7) DQ (44:47) 10 DQ (40:43) 10 DQM DQ (0:3) CS D0 CS D1 DQ (36:39) RDQMB5 10 DQM DQ (0:3) DQM DQ (0:3) CS D 11 CS D 12 CS D 13 VCC C RS2 RDQMB2 10 DQ (16:19) 10 DQ (20:23) RDQMB3 10 DQ (24:27) 10 DQ (28:31) DQM DQ (0:3) CS D7 CS D8 DQ (60:63) DQ (56:59) 10 DQM DQ (0:3) CS D5 CS D6 DQ (52:55) RDQMB7 10 CS DQM DQ (0:3) 10 D 16 DQM DQ (0:3) CS D 17 DQ (48:51) 10 RDQMB6 10 DQM DQ (0:3) CS D 14 CS D 15 VSS D 0 -17 D 0 -17 DQ (32:35) 10 VSS PLL Each SDRAM PLL CLK CLK1, CLK2, CLK3 30 pF Register D 18, D 19 A Y RS0, RS2 RDQMB0 to RDQMB7 RBA0, RBA1 RA0 to RA11 RRAS RCAS RWE RCKE0 SCL WP 47 k Serial PD D 21 SDA SA0 SA1 SA2 VSS CLK1, CLK2, CLK3 to be terminated 10 LE OE CLK RDQMB4 10 DQM DQ (0:3) CS D9 CS D 10 DQM DQ (0:3) DQM DQ (0:3) DQM DQ (0:3) DQM DQ (0:3) DQM DQ (0:3) DQM DQ (0:3) DQM DQ (0:3) 6 To Top / Lineup / Index MB8516SR72CA-102/-103/-102L/-103L s ABSOLUTE MAXIMUM RATINGS (See WARNING) Parameter Supply Voltage* Input Voltage* Output Voltage* Storage Temperature Power Dissipation Output Current (D.C.) * : Voltages referenced to VSS (= 0 V) WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current, temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings. Symbol VCC VIN VOUT TSTG PD IOUT Value Min. -0.5 -0.5 -0.5 -55 -- -50 Max. +4.6 +4.6 +4.6 +125 21 +50 Unit V V V C W mA s RECOMMENDED OPERATING CONDITIONS Parameter Supply Voltage Input High Voltage, All Inputs Input Low Voltage, All Inputs Ambient Temperature Notes *1 *1, 2 *1, 3 Symbol VCC VSS VIH VIL TA Value Min. 3.0 0 2.0 -0.5 0 Typ. 3.3 0 -- -- -- Max. 3.6 0 VCC +0.5 0.8 +70 Unit V V V V C *1. Voltages referenced to VSS (=0V) *2. Overshoot limit: VIH (max.) = VCC +1.5 V with a pulse-width 5 ns. *3. Undershoot limit: VIL (min.) = -1.5 V with a pulse-width 5 ns. WARNING: The recommended operating conditions are required in order to ensure the normal operation of the semiconductor device. All of the device's electrical characteristics are warranted when the device is operated within these ranges. Always use semiconductor devices within their recommended operating conditionranges. Operation outside these ranges may adversely affect reliability and could result in device failure. No warranty is made with respect to uses, operating conditions, or combinations not represented on the data sheet. Users considering application outside the listed conditions are advised to contact their FUJITSU representatives beforehand. 7 To Top / Lineup / Index MB8516SR72CA-102/-103/-102L/-103L s CAPACITANCE (VCC = +3.3 V, f = 1 MHz, TA = +25C) Parameter A0 to A11, BA0, BA1 RAS, CAS, WE S0, S2 CKE0 Input Capacitance CLK0 to CLK3 DQMB0 to DQMB7 SCL SA0, SA1, SA2 REGE SDA Input/Output Capacitance DQ0 to DQ63 CB0 to CB7 Symbol CIN1 CIN2 CIN3 CIN4 CIN5 CIN6 CIN7 CIN8 CIN9 CSDA CDQ CCB Value Min. -- -- -- -- -- -- -- -- -- -- -- -- Max. 8 9 10 14 38 9 5 6 23 6 13 13 Unit pF pF pF pF pF pF pF pF pF pF pF pF 8 To Top / Lineup / Index MB8516SR72CA-102/-103/-102L/-103L s DC CHARACTERISTICS (At recommended operating conditions unless otherwise noted.) Notes 1, 2, 3 Value Parameter Notes Symbol Condition Max. Min. Std. ver. Low ver. Unit ICC1S Operating Current (Average Power Supply Current) *4 Burst Length = 1, tRC = min for BL = 1, tCK = min, One Bank Active, Outputs Open, Address changed up to 1 time during tCK(min.), 0 V VIN VIL max VIH min VIN VCC Burst Length = 1 (each Bank), tRC = min for BL = 1 (each Bank), tCK = min, Two Banks Active, Outputs Open, Address changed up to 1 time during tCK(min.), 0 V VIN VIL max VIH min VIN VCC CKE = VIL, tCK = min, All Banks Idle, Power Down Mode, 0 V VIN VIL max VIH min VIN VCC CKE = VIL, CLK = VIH or VIL, All Banks Idle, Power Down Mode, 0 V VIN VIL max VIH min VIN VCC CKE = VIH, tCK = min, All Banks Idle, NOP commands only, Input signals (except to CMD) are changed one time during 3 clock cycles, 0 V VIN VIL max VIH min VIN VCC CKE = VIH, CLK = VIH or VIL, All Banks Idle, Input Signals are Stable, 0 V VIN VIL max VIH min VIN VCC -- 2130 mA ICC1D -- 3760 mA ICC2P -- 155 137 mA ICC2PS -- 137 128 mA Precharge Standby Current (Power Supply Current) *4 ICC2N -- 390 mA ICC2NS -- 155 mA (Continued) 9 To Top / Lineup / Index MB8516SR72CA-102/-103/-102L/-103L (Continued) Value Parameter Notes Symbol Condition Max. Min. Std. ver. 155 Low ver. 137 Unit ICC3P CKE = VIL, tCK = min, Any Bank Active, 0 V VIN VIL max VIH min VIN VCC CKE = VIL, CLK = VIH or VIL, Any Bank Active, 0 V VIN VIL max VIH min VIN VCC CKE = VIH, tCK = min, Any Bank Active, NOP commands only, Input signals (except to CMD) are changed one time during 3 clock cycles, 0 V VIN VIL max VIH min VIN VCC CKE = VIH, CLK = VIH or VIL, Any Bank Active, 0 V VIN VIL max VIH min VIN VCC tCK = min, Gapless data, Burst Length = 4, Outputs open, Multiple-banks Active, 0 V VIN VIL max VIH min VIN VCC Auto Refresh, tCK = min, tRC = min, 0 V VIN VIL max VIH min VIN VCC Self-refresh, tCK = min, CKE 0.2 V, 0 V VIN VIL max VIH min VIN VCC 0 V VIN VCC All other pins not under test = 0 V Output is disabled (Hi-Z) 0 V VIN VCC IOH = -2.0 mA IOL = +2.0 mA -- mA ICC3PS -- 137 128 mA Active Standby Current (Power Supply Current) *4 ICC3N -- 570 mA ICC3NS -- 155 mA Burst Mode Current (Average Power Supply Current) *4 ICC4 -- 1835 mA Auto-refresh Current (Average Power Supply Current) *4 ICC5 -- 4456 mA Self-refresh Current (Average Power Supply Current) *4 ICC6 -- 137 128 mA REGE Input Leakage Current Others Output Leakage Current LVTTL Output High Voltage LVTTL Output Low Voltage *5 *5 ILO VOH VOL ILI -50 -10 -10 2.4 -- 50 10 10 -- 0.4 A A V V 10 To Top / Lineup / Index MB8516SR72CA-102/-103/-102L/-103L Notes: *1. An initial pause (DESL on NOP) of 200 s is required after power-on followed by a minimum of eight Auto-refresh cycles. *2. Values of ICC1S, ICC1D and ICC4 are for when one side of the double-sided module is in standby mode (ICC2N)and the other side is in active. *3. DC characteristics is the Serial PD standby state (VIN = GND or VCC). *4. ICC depends on the output termination, load conditions, clock cycle rate and signal clock rate. The specified values are obtained with the output open and no termination resistors. *5. Voltages referenced to VSS (= 0 V) 11 To Top / Lineup / Index MB8516SR72CA-102/-103/-102L/-103L s AC CHARACTERISTICS (SDRAM Component Specifications) Notes 1, 2, 3 (1) BASE CHARACTERISTICS (At recommended operating conditions unless otherwise noted.) No. Parameter Notes CL = 2 CL = 3 Symbol tCK2 tCK3 tCH tCL Registered Mode Registered Mode CL = 2 *4, *5, *6 CL = 3 tAC3 tLZ *4, *7 CL = 2 CL = 3 tHZ2 tHZ3 tOH tREF tT tCKSP -- 0 3 3 3 -- 0.5 3.5 6 -- 6 6 -- 65.6 2 -- -- 0 3 3 3 -- 0.5 3.5 6 -- 8 6 -- 65.6 2 -- ns ns ns ms ns ns tSI tHI tAC2 MB8516SR72CA MB8516SR72CA -102/-102L -103/-103L Unit Min. Max. Min. Max. 10 10 3 3 3.5 2.5 -- -- -- -- -- -- -- 6 15 10 3 3 3.5 2.5 -- -- -- -- -- -- -- 8 ns ns ns ns ns ns 1 2 3 4 5 6 7 8 9 Clock Period Clock High Time Clock Low Time Input Setup Time Input Hold Time Output Valid from Clock (tCK = min) Output in Low-Z Output in High-Z Output Hold Time *4 10 Time between Refresh 11 Transition Time 12 CKE Setup Time for Power Down Registered Mode Exit Time 12 To Top / Lineup / Index MB8516SR72CA-102/-103/-102L/-103L (2) BASE VALUES FOR CLOCK COUNT/LATENCY No. 1 2 3 4 5 6 7 8 9 RAS Cycle Time RAS Precharge Time RAS Active Time RAS to CAS Delay Time Write Recovery Time Data-in to Precharge Lead Time Data-in to Active/Refresh Command Period Mode Register Set Cycle Time RAS to RAS Bank Active Delay Time *4 CL = 2 CL = 3 *9 Parameter Notes *8 MB8516SR72CA Symbol -102/-103/-102L/-103L Unit Min. Max. tRC tRP tRAS tRCD tWR tDPL tDAL2 tDAL3 tRSC tRRD 70 20 50 20 10 10 1 cyc + tRP 2 cyc + tRP 20 20 -- -- 110000 -- -- -- -- -- -- -- ns ns ns ns ns ns ns ns ns (3) CLOCK COUNT FORMULA (*10) Clock Base Value Clock Period (Round off a whole number) (4) LATENCY (The latency values on these parameters are fixed regardless of clock period.) No. 1 2 3 4 5 6 7 8 9 Parameter CKE to Clock Disable DQM to Output in High-Z DQM to Input Data Delay Last Output to Write Command Delay Write Command to Input Data Delay Precharge to Output in High-Z Delay Burst Stop Command to Output in High-Z Delay CAS to CAS Delay (min) CAS Bank Delay (min) *4 *4 CL = 2 CL = 3 CL = 2 CL = 3 Notes Symbol ICKE IDQZ IDQD IOWD IDWD IROH2 IROH3 IBSH2 IBSH3 ICCD ICBD MB8516SR72CA -102/-103/-102L/-103L Registered Mode 2 3 1 1 1 3 4 3 4 1 1 Cycle Cycle Cycle Cycle Cycle Cycle Cycle Cycle Cycle Unit 13 To Top / Lineup / Index MB8516SR72CA-102/-103/-102L/-103L Notes: *1. An initial pause (DESL on NOP) of 200 s is required after power-up followed by a minimum of eight Auto-refresh cycles. *2. 1.4 V or VREF is the reference level for measuring timing of signals. Transition times are measured between VIH (min) and VIL (max). *3. AC characteristics assume tT = 1 ns and 50 pF of capacitance load. *4. For Registered Mode, actual CAS Latency is added one cycle to the CAS Latency of this value because of a delay by registers. *5. Assumes tRCD is satisfied. *6. tAC also specifies the access time at burst mode except for first access. *7. Specified where output buffer is no longer driven. *8. Actual clock count of tRC (IRC) will be sum of clock count of tRAS (IRAS) and tRP (IRP). *9. Operation within the tRCD (min) ensures that access time is determined by tRCD (min) +tAC (max) ; if tRCD is greater than the specified tRCD (min), access time is determined by tAC. *10. All base values are measured from the clock edge at the command input to the clock edge for the next command input. All clock counts are calculated by a simple formula: clock count equals base value divided by clock period (round off to a whole number). *Source: See MB81F64442C Data Sheet for details on the electrical. s AC OPERATING TEST CONDITION (Example of AC Test Load Circuit) 1.4 V 50 Z = 50 I/O 50 pF 14 To Top / Lineup / Index MB8516SR72CA-102/-103/-102L/-103L s SERIAL PRESENCE DETECT(SPD) FUNCTION 1. PIN DESCRIPTIONS SCL (Serial Clock) SCL input is used to clock all data input/output of SPD. SDA (Serial Data) SDA is a common pin used for all data input/output of SPD. The SDA pull-up resistor is required due to the open-drain output. SA0, SA1, SA2 (Address) Address inputs are used to set the least significant three bits of the eight bits slave address. The address inputs must be fixed to select a particular module and the fixed address of each module must be different each other. 2. SPD OPERATIONS CLOCK and DATA CONVENTION Data states on the SDA can change only during SCL= Low. SDA state changes during SCL = High are indicated start and stop conditions. Refer to Fig. 1 below. START CONDITION All commands are preceded by a start condition, which is a transition of SDA state from High to Low when SCL = High. SPD will not respond to any command until this condition has been met. STOP CONDITION All read or write operation must be terminated by a stop condition, which is a transition of SDA state from Low to High when SCL = High. The stop condition is also used to make the SPD into the state of standby power mode after a read sequence. Fig. 1 - START AND STOP CONDITIONS SCL SDA START START = High to Low transition of SDA state when SCL is High STOP = Low to High transition of SDA state when SCL is High STOP 15 To Top / Lineup / Index MB8516SR72CA-102/-103/-102L/-103L ACKNOWLEDGE Acknowledge is a software convention used to indicate successful data transfer. The transmitting device, either master or slave, will release the bus after transmitting eight bits. During the ninth clock cycle the receiver will put the SDA line to Low in order to acknowledge that it received the eight bits of data. The SPD will respond with an acknowledge when it received the start condition followed by slave address issued by master. In the read operation, the SPD will transmit eight bits of data, release the SDA line and monitor the line for an acknowledge. If an acknowledge is detected and no stop condition is issued by master, the SPD will continue to transmit data. If an acknowledge is not detected, the SPD will terminated further data transmissions. The master must then issue a stop condition to return the SPD to the standby power mode. In the write operation, upon receipt of eight bits of data the SPD will respond with an acknowledge, and await the next eight bits of data, again responding with an acknowledge until the stop condition is issued by master. SLAVE ADDRESS ADDRESSING Following a start condition, the master must output the eight bits slave address. The most significant four bits of the slave address are device type identifier. For the SPD this is fixed as 1010[B]. Refer to the Fig. 2 below. The next three significant bits are used to select a particular device. A system could have up to eight SPD devices --namely up to eight modules-- on the bus. The eight addresses for eight SPD devices are defined by the state of the SA0, SA1 and SA2 inputs. The last bit of the slave address defines the operation to be performed. When R/W bit is "1", a read operation is selected, when R/W bit is "0", a write operation is selected. Following the start condition, the SPD monitors the SDA line comparing the slave address being transmitted with its slave address (device type and state of SA0, SA1, and SA2 inputs). Upon a correct compare the SPD outputs an acknowledge on the SDA line. Depending on the state of the R/W bit, the SPD will execute a read or write operation. Fig. 2 - SLAVE ADDRESS DEVICE TYPE IDENTIFIER DEVICE ADDRESS 1 0 1 0 SA2 SA1 SA0 R/W 16 To Top / Lineup / Index MB8516SR72CA-102/-103/-102L/-103L 3. READ OPERATIONS CURRENT ADDRESS READ Internally the SPD contains an address counter that maintains the address of the last data accessed, incriminated by one. Therefore, if the last access (either a read or write operation) was to address(n), the next read operation would access data from address(n+1). Upon receipt of the slave address with the R/W bit = "1", the SPD issues an acknowledge and transmits the eight bits of data during the next eight clock cycles. The master terminates this transmission by issuing a stop condition, omitting the ninth clock cycle acknowledge. Refer to Fig. 3 for the sequence of address, acknowledge and data transfer. Fig. 3 - CURRENT ADDRESS READ S T A R T SLAVE ADDRESS S T O P BUS ACTIVITY : MASTER SDA LINE BUS ACTIVITY : SPD A C K DATA RANDOM READ Random Read operations allow the master to access any memory location in a random manner. Prior to issuing the slave address with the R/W bit = "1", the master must first perform a "dummy" write operation on the SPD. The master issues the start condition, and the slave address followed by the word address. After the word address acknowledge, the master immediately reissues the start condition and the slave address with the R/ W bit = "1". This will be followed by an acknowledge from the SPD and then by the eight bits of data. The master terminates this transmission by issuing a stop condition, omitting the ninth clock cycle acknowledge. Refer to Fig. 4 for the sequence of address, acknowledge and data transfer. Fig. 4 - RANDOM READ S T BUS ACTIVITY : A R MASTER T SDA LINE BUS ACTIVITY : SPD A C K A C K A C K S T A R T SLAVE ADDRESS WORD ADDRESS SLAVE ADDRESS S T O P DATA 17 To Top / Lineup / Index MB8516SR72CA-102/-103/-102L/-103L SEQUENTIAL READ Sequential Read can be initiated as either a current address read or random read. The first data are transmitted as with the other read mode, however, the master now responds with an acknowledge, indicating it requires additional data. The SPD continues to output data for each acknowledge received. The master terminates this transmission by issuing a stop condition, omitting the ninth clock cycle acknowledge. Refer to Fig. 5 for the sequence of address, acknowledge and data transfer. The data output is sequential, with the data from address(n) followed by the data from address(n+1). The address counter for read operations increments all address bits, allowing the entire memory contents to be serially read during one operation. At the end of the address space (address 255), the counter "rolls over" to address 0 and the SPD continues to output data for each acknowledge received. Fig. 5 - SEQUENTIAL READ SLAVE ADDRESS BUS ACTIVITY : MASTER SDA LINE BUS ACTIVITY : SPD A C K A C K A C K A C K S T O P DATA (n) DATA (n+1) DATA (n+2) DATA (n+x) 4. DC CHARACTERISTICS Parameter Input Leakage Current Output Leakage Current Output Low Voltage Note: *1. Referenced to VSS. *1 Note Symbol SILI SILO SVOL Condition 0 V VIN VCC 0 V VOUT VCC IOL = 3.0 mA Value Min. -10 -10 -- Max. 10 10 0.4 Unit A A V 18 To Top / Lineup / Index MB8516SR72CA-102/-103/-102L/-103L 5. AC CHARACTERISTICS No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Parameter SCL Clock Frequency Noise Suppression Time Constant at SCL, SDA Inputs SCL Low to SDA Data Out Valid Time the Bus Must Be Free Before a New Transmission Can Start Start Condition Hold Time Clock Low Period Clock High Period Start Condition Setup Time Data in Hold Time Data in Setup Time SDA and SCL Rise Time SDA and SCL Fall Time Stop Condition Setup Time Data Out Hold Time Write Cycle Time Symbol fSCL TI tAA tBUF tHD:STA tLOW tHIGH tSU:STA tHD:DAT tSU:DAT tR tF tSU:STO tDH tWR Value Min. -- -- -- 4.7 4.0 4.7 4.0 4.7 0 250 -- -- 4.7 100 -- Max. 100 100 3.5 -- -- -- -- -- -- -- 1 300 -- -- 15 Unit KHz ns s s s s s s s ns s ns s ns ms Fig. 6 - TIMING WAVEFORM tF tR tLOW SCL tSU : STA tHD : DAT tHD : STA SDA (input) tAA SDA (output) tDH tSU : DAT tSU : STO tHIGH tBUF 19 To Top / Lineup / Index MB8516SR72CA-102/-103/-102L/-103L s PACKAGE DIMENSIONS 168-pin plastic DIMM (socket type) (MDS-168P-P43) Under development Dimension in mm (inches) 20 To Top / Lineup / Index MB8516SR72CA-102/-103/-102L/-103L FUJITSU LIMITED For further information please contact: Japan FUJITSU LIMITED Corporate Global Business Support Division Electronic Devices KAWASAKI PLANT, 4-1-1, Kamikodanaka Nakahara-ku, Kawasaki-shi Kanagawa 211-8588, Japan Tel: 81(44) 754-3763 Fax: 81(44) 754-3329 All Rights Reserved. The contents of this document are subject to change without notice. Customers are advised to consult with FUJITSU sales representatives before ordering. The information and circuit diagrams in this document are presented as examples of semiconductor device applications, and are not intended to be incorporated in devices for actual use. Also, FUJITSU is unable to assume responsibility for infringement of any patent rights or other rights of third parties arising from the use of this information or circuit diagrams. FUJITSU semiconductor devices are intended for use in standard applications (computers, office automation and other office equipment, industrial, communications, and measurement equipment, personal or household devices, etc.). CAUTION: Customers considering the use of our products in special applications where failure or abnormal operation may directly affect human lives or cause physical injury or property damage, or where extremely high levels of reliability are demanded (such as aerospace systems, atomic energy controls, sea floor repeaters, vehicle operating controls, medical devices for life support, etc.) are requested to consult with FUJITSU sales representatives before such use. The company will not be responsible for damages arising from such use without prior approval. Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current levels and other abnormal operating conditions. If any products described in this document represent goods or technologies subject to certain restrictions on export under the Foreign Exchange and Foreign Trade Law of Japan, the prior authorization by Japanese government will be required for export of those products from Japan. http://www.fujitsu.co.jp/ North and South America FUJITSU MICROELECTRONICS, INC. Semiconductor Division 3545 North First Street San Jose, CA 95134-1804, USA Tel: (408) 922-9000 Fax: (408) 922-9179 Customer Response Center Mon. - Fri.: 7 am - 5 pm (PST) Tel: (800) 866-8608 Fax: (408) 922-9179 http://www.fujitsumicro.com/ Europe FUJITSU MIKROELEKTRONIK GmbH Am Siebenstein 6-10 D-63303 Dreieich-Buchschlag Germany Tel: (06103) 690-0 Fax: (06103) 690-122 http://www.fujitsu-ede.com/ Asia Pacific FUJITSU MICROELECTRONICS ASIA PTE LTD #05-08, 151 Lorong Chuan New Tech Park Singapore 556741 Tel: (65) 281-0770 Fax: (65) 281-0220 http://www.fmap.com.sg/ F9812 (c) FUJITSU LIMITED Printed in Japan 21 |
Price & Availability of MB8516SR72CA-103L |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |