Part Number Hot Search : 
MB90F867 30EPF10 160N04 DATASHE SERIES SP483E 1078093 527268B
Product Description
Full Text Search
 

To Download LTC1669 Datasheet File

  If you can't view the Datasheet, Please click here to try to view without PDF Reader .  
 
 


  Datasheet File OCR Text:
 LTC1669 10-Bit Rail-to-Rail Micropower DAC with I2C Interface
FEATURES
s s s s
DESCRIPTIO
s s s s s s s s
Micropower 10-Bit DAC in SOT-23 Low Operating Current: 60A Ultralow Power Shutdown Mode: 12A 2-Wire Serial Interface Compatible with I2CTM Selectable Internal Reference or Ratiometric to VCC Maximum DNL Error: 0.75LSB 8 User Selectable Addresses (MSOP Package) Single 2.7V to 5.5V Operation Buffered True Rail-to-Rail Voltage Output Power-On Reset 1.5V VIL and 2.1V VIH for SDA and SCL Small 5-Lead SOT-23 and 8-Lead MSOP Packages
The LTC(R)1669 is a 10-bit voltage output DAC with true buffered rail-to-rail output voltage capability. It operates from a single supply with a range of 2.7V to 5.5V. The reference for the DAC is selectable between the supply voltage or an internal bandgap reference. Selecting the internal bandgap reference will set the full-scale output voltage range to 2.5V. Selecting the supply as the reference sets the output voltage range to the supply voltage. The part features a simple 2-wire serial interface compatible with I2C that allows communication between many devices. The internal data registers are double buffered to allow for simultaneous update of several devices at once. The DAC can be put in low current power-down mode for use in power conscious systems. Power-on reset ensures the DAC output is at 0V when power is initially applied, and all internal registers are cleared. The LTC1669 is pin-for-pin compatible with the LTC1663.
, LTC and LT are registered trademarks of Linear Technology Corporation. I2C is a trademark of Philips Electronics N.V.
APPLICATIO S
s s s s s s
Digital Calibration Offset/Gain Adjustment Industrial Process Control Automatic Test Equipment Arbitrary Function Generators Battery-Powered Data Conversion Products
BLOCK DIAGRA
4 (5) VCC 1.25V BANDGAP REFERENCE
REFERENCE SELECT
ERROR (LSB)
10-BIT DAC LATCH 10-BIT BUFFERED VOUT DAC MSOP PACKAGE ONLY (6) AD0 (2) AD1 (3) AD2 2-WIRE INTERFACE SDA 1 (1) SCL 5 (4) GND 2 (7)
1669 BD
VOUT 3 (8)
COMMAND LATCH
INPUT LATCH
NOTE: PIN NUMBERS IN PARENTHESES REFER TO THE MSOP PACKAGE
1669f
U
Differential Nonlinearity (DNL)
1.0 0.8 0.6 0.4 0.2 0 - 0.2 - 0.4 - 0.6 - 0.8 -1.0 0 28 156 384 512 640 768 896 1024 CODE
1669 G02
W
U
VREF = VCC = 5V TA = 25C
1
LTC1669 ABSOLUTE AXI U RATI GS
VCC to GND .............................................. - 0.3V to 7.5V SDA, SCL ..................................................- 0.3V to 7.5V AD0, AD1, AD2 (MSOP Only) ...... - 0.3V to (VCC + 0.3V) VOUT ............................................ - 0.3V to (VCC + 0.3V)
PACKAGE/ORDER I FOR ATIO
TOP VIEW SDA AD1 AD2 SCL 1 2 3 4 8 7 6 5 VOUT GND AD0 VCC
ORDER PART NUMBER
TOP VIEW
LTC1669CMS8 LTC1669IMS8
LTC1669-8CMS8 LTC1669-8IMS8
MS8 PACKAGE 8-LEAD PLASTIC MSOP
MS8 PART MARKING LTAHV LTAHX LTAHT LTAHU
TJMAX = 125C, JA = 150C/W
Consult LTC Marketing for parts specified with wider operating temperature ranges.
The q denotes specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. VCC = 2.7V to 5.5V, VCC set as reference, VOUT unloaded, unless otherwise noted.
SYMBOL DAC Resolution Monotonicity DNL INL VOS VOSTC FSE VOUT VFSTC PSRR Differential Nonlinearity Integral Nonlinearity Offset Error Offset Error Temperature Coefficient Full-Scale Error DAC Output Span Full-Scale Voltage Temperature Coefficient Power Supply Rejection Ratio Reference Set to VCC Reference Set to Internal Bandgap Reference Set to VCC Reference Set to Internal Bandgap Reference Set to VCC Reference Set to Internal Bandgap Reference Set to Internal Bandgap, Code = 1023
q q q q
ELECTRICAL CHARACTERISTICS
PARAMETER
CONDITIONS
(Note 2) Guaranteed Monotonic (Note 2) (Note 2) Measured at Code 20
Power Supply VCC ICC ISD Positive Supply Voltage Supply Current Supply Current in Shutdown Mode Short-Circuit Current (Sourcing) Short-Circuit Current (Sinking) VCC = 3V (Note 3) VCC = 5V (Note 3) (Note 3) VOUT Shorted to GND, Input Code = 1023 VOUT Shorted to VCC, Input Code = 0 2.7 60 75 12 25 30 5.5 100 125 24 100 120 V A A A mA mA
1669f
Op Amp DC Performance
q q
2
U
U
W
WW U
W
(Note 1)
Operating Temperature Range LTC1669C .............................................. 0C to 70C LTC1669I ........................................... - 40C to 85C Storage Temperature Range ................ - 65C to 150C Lead Temperature (Soldering, 10 sec)................. 300C
ORDER PART NUMBER
SDA 1 GND 2 VOUT 3 4 VCC 5 SCL
LTC1669CS5 LTC1669-1CS5 S5 PART MARKING LTAHW LTAHR
S5 PACKAGE 5-LEAD PLASTIC SOT-23
TJMAX = 125C, JA = 250C/W
MIN 10 10
TYP
MAX
UNITS Bits Bits
q q q q
0.2 0.5 10 15 3 3 0 to VCC 0 to 2.5 30 50 0.4
0.75 2.5 30 15 15
LSB LSB mV V/C LSB LSB V V V/C V/C LSB/V
q q q
LTC1669
The q denotes specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. VCC = 2.7V to 5.5V, VCC set as reference, VOUT unloaded, unless otherwise noted.
SYMBOL PARAMETER Output Impedance to GND CONDITIONS Input Code = 0, VCC = 5V Input Code = 0, VCC = 3V In Shutdown Mode Input Code = 1023, VCC = 5V Input Code = 1023, VCC = 3V Rising (Notes 4, 5) Falling (Notes 4, 5) To 0.5LSB (Notes 4, 5) 1LSB Change Around Major Carry
q q
ELECTRICAL CHARACTERISTICS
MIN
TYP 65 150 500 80 120 0.75 0.25 30 0.75 70
MAX
UNITS k V/s V/s s nV * s nV * s V
Output Impedance to VCC AC Performance Voltage Output Slew Rate Voltage Output Settling Time Digital Feedthrough Digital-to-Analog Glitch Impulse Digital Inputs SCL, SDA VIH VIL VLTH ILEAK CIN VOL IUP VIH VIL High Level Input Voltage Low Level Input Voltage Logic Threshold Voltage Digital Input Leakage Digital Input Capacitance Digital Output Low Voltage Address Pin Pull-Up Current High Level Input Voltage Low Level Input Voltage
2.1 1.5 1.8 1 10 0.4 0.5 1.5 0.8
V V A pF V A V V
VCC = 5.5V and 0V, VIN = GND to VCC (Note 7) IPULLUP = 3mA VIN = 0V
q q q q q VCC - 0.3 q
Digital Output SDA Address Inputs AD0, AD1, AD2 (MSOP Only)
TI I G CHARACTERISTICS
SYMBOL fSCL tBUF tHD, STA tSU, STA tSU, STO tHD, DAT (IN) tHD, DAT (OUT) tSU, DAT tLOW tHIGH tf tr PARAMETER Clock Operating Frequency Timing Characteristics (Notes 6, 7)
The q denotes specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. VCC = 2.7V to 5.5V, VCC set as reference, VOUT unloaded, unless otherwise noted.
MIN
q q q q q q q q q q q q
Note 1: Absolute maximum ratings are those values beyond which the life of a device may be impaired. Note 2: Nonlinearity and monotonicity are defined from code 20 to code 1003 (full scale). See Applications Information. Note 3: Digital inputs at 0V or VCC.
UW
TYP
MAX 100
UNITS kHz s s s s ns
Bus Free Time Between Stop and Start Condition Hold Time After (Repeated) Start Condition Repeated Start Condition Setup Time Stop Condition Setup Time Data Hold Time (Input) Data Hold Time (Output) Data Setup Time Clock Low Period Clock High Period Clock, Data Fall Time Clock, Data Rise Time
4.7 4 4.7 4 0 225 250 4.7 4 20 20 300 1000 500 3450
ns ns s s ns ns
Note 4: Load is 10k in parallel with 100pF. Note 5: VCC = VREF = 5V. DAC switched between 0.1VFS and 0.9VFS, i.e., codes k = 102 and k = 922. Note 6: All values are referenced to VIH and VIL levels. Note 7: Guaranteed by design and not subject to test.
1669f
3
LTC1669 TYPICAL PERFOR A CE CHARACTERISTICS
Integral Nonlinearity (INL)
1.0 0.8 0.6 0.4
ERROR (LSB)
ERROR (LSB)
VREF = VCC = 5V TA = 25C
0.4 0.2 0 - 0.2 - 0.4 - 0.6 - 0.8 -1.0 0 28 156 384 512 640 768 896 1024 CODE
1669 G01
OUTPUT VOLTAGE (V)
0.2 0 - 0.2 - 0.4 - 0.6 - 0.8 -1.0
Large-Signal Step Response
5 SDA (VOLTS) 0 5 CODE = 990 4 3 VOUT (VOLTS) 2 1 CODE = 32 0 5s/DIV
1669 G04
VOUT (LSB)
VCC = 5V RL = 4.7k CL = 100pF TA = 25C
Load Regulation vs Output Current
1.0 0.8 0.6 0.4
VOUT (LSB)
OFFSET ERROR VOLTAGE (mV)
2 1 0 -1 -2 -3 -4 -5 -60 -40 -20 0 20 40 60 TEMPERATURE (C) 80 100
OUTPUT VOLTAGE (V)
VCC = VREF = 3V VOUT = 1.5V CODE = 512 TA = 25C
0.2 0 SOURCE SINK
- 0.2 - 0.4 - 0.6 - 0.8 -1.0 -1.0 - 0.8- 0.6- 0.4- 0.2 0 0.2 0.4 0.6 0.8 1.0 IOUT (mA)
1669 G07
4
UW
Differential Nonlinearity (DNL)
1.0 0.8 0.6 VREF = VCC = 5V TA = 25C
5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5
Source and Sink Current Capability with VCC = 5V
TA = 25C DAC CODE = 1023
DAC CODE = 0
0
28
156 384 512 640 768 896 1024 CODE
1669 G02
0
0
1 2 3 4 5 6 7 8 9 10 OUTPUT CURRENT SOURCE/SINK (mA)
1669 G03
Midscale Glitch
1.0 5V SDA 0V CODE = 512 TO 511 0.8 0.6 0.4 0.2 0
Load Regulation vs Output Current
VCC = VREF = 5V VOUT = 2.5V CODE = 512 TA = 25C
VOUT 10mV/DIV VCC = 5V RL = 4.7k CL = 100pF TA = 25C 2s/DIV
1669 G05
- 0.2 - 0.4 - 0.6 - 0.8 -1.0 -4 -3 -2 -1 0 1 IOUT (mA) 2 3 4 SOURCE SINK
1669 G06
Offset Error Voltage vs Temperature
5 4 3 2.510 2.508 2.506 2.504 2.502 2.500 2.498 2.496 2.494 2.492
Full-Scale Output Voltage vs Temperature
REFERENCE SET TO INTERNAL BANDGAP
2.490 -60 -40 -20 0 20 40 60 TEMPERATURE (C)
80
100
1669 G08
1669 G09
1669f
LTC1669
PIN FUNCTIONS
SDA (Pin 1, Pin 1 on SOT-23): Serial Data Bidirectional Pin. Data is shifted into the SDA pin and acknowledged by the SDA pin. High impedance pin while data is shifted in. Open-drain N-channel output during acknowledgment. Requires a pull-up resistor or current source to VCC. AD1 (Pin 2): Slave Address Select Bit 1. Tie this pin to either VCC or GND to modify the corresponding bit of the LTC1669's slave address. AD2 (Pin 3): Slave Address Select Bit 2. Tie this pin to either VCC or GND to modify the corresponding bit of the LTC1669's slave address. SCL (Pin 4, Pin 5 on SOT-23): Serial Clock Input Pin. Data is shifted into the SDA pin at the rising edges of the clock. This high impedance pin requires a pull-up resistor or current source to VCC. VCC (Pin 5, Pin 4 on SOT-23): Power Supply. 2.7V VCC 5.5V. Also used as the reference voltage input when the part is programmed to use VCC as the reference. AD0 (Pin 6): Slave Address Select Bit 0. Tie this pin to either VCC or GND to modify the corresponding bit of the LTC1669's slave address. GND (Pin 7, Pin 2 on SOT-23): System Ground. VOUT (Pin 8, Pin 3 on SOT-23): Voltage Output. Buffered rail-to-rail DAC output.
DEFINITIONS
Differential Nonlinearity (DNL): The difference between the measured change and the ideal 1LSB change for any two adjacent codes. The DNL error between any two codes is calculated as follows: DNL = (VOUT - LSB)/LSB Where VOUT is the measured voltage difference between two adjacent codes. Digital Feedthrough: The glitch that appears at the analog output caused by AC coupling from the digital inputs when they change state. The area of the glitch is specified in (nV)(sec). Full-Scale Error (FSE): The deviation of the actual fullscale voltage from ideal. FSE includes the effects of offset and gain errors (see Applications Information). Integral Nonlinearity (INL): The deviation from a straight line passing through the endpoints of the DAC transfer curve (Endpoint INL). Because the output cannot go below zero, the linearity is measured between full scale and the lowest code that guarantees the output will be greater than zero. The INL error at a given input code is calculated as follows: INL = [VOUT - VOS - (VFS - VOS)(code/1023)]/LSB Where VOUT is the output voltage of the DAC measured at the given input code. Least Significant Bit (LSB): The ideal voltage difference between two successive codes. LSB = VREF/1024 Resolution (n): Defines the number of DAC output states (2n) that divide the full-scale range. Resolution does not imply linearity. Voltage Offset Error (VOS): Nominally, the voltage at the output when the DAC is loaded with all zeros. A single supply DAC can have a true negative offset, but the output cannot go below zero (see Applications Information). For this reason, single supply DAC offset is measured at the lowest code that guarantees the output will be greater than zero.
U
U
U
U
U
1669f
5
UW
LTC1669
tLOW tHD, DAT
1663 TD
tHD, STA
tBUF tSU, STO
SCL tHIGH tr tf REPEATED START CONDITION STOP CONDITION START CONDITION
tHD, STA
START CONDITION
Typical LTC1669 Input Waveform--Programming DAC Output for Full Scale (AD2 to AD0 Set High)
COMMAND AD0 WR X X X X X BG SD SY D7 D6 D5 LS DATA D4 D3 D2 D1 D0 X X X MS DATA X X X D9 D8 STOP 1 0 ACK X X X X X 0 0 0 ACK 1 1 1 1 1 1 1 1 ACK X X X X X X 1 1 ACK
ADDRESS
0
1
0
0
AD2
AD1
START
SDA
0
1
0
0
1
1
SCL
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9 FULL-SCALE VOLTAGE ZERO-SCALE VOLTAGE
1669 TA02
VOUT
NOTE: X = DON'T CARE
W
6
TI I G DIAGRA
tSU, DAT tSU, STA
SDA
1669f
LTC1669
APPLICATIONS INFORMATION
Write Word Protocol Used by the LTC1669
1 S 7 Slave Address 1 Wr 1 A 8 Command Byte 1 A 8 LSData Byte 1 A 8 MSData Byte 1 A 1 P
1669 TA03
S = Start Condition, Wr = Write Bit = 0, A = Acknowledge, P = Stop Condition
Serial Digital Interface The LTC1669 communicates with a host (master) using the standard 2-wire interface. The Timing Diagram shows the timing relationship of the signals on the bus. The two bus lines, SDA and SCL, must be high when the bus is not in use. External pull-up resistors or current sources, such as the LTC1694 SMBus/I2C Accelerator, are required on these lines. The LTC1669 is a receive-only (slave) device. The master can communicate with the LTC1669 using the Quick Command, Send Byte or Write Word protocols as explained later. The START and STOP Conditions When the bus is not in use, both SCL and SDA must be high. A bus master signals the beginning of a communication to a slave device by transmitting a START condition. A START condition is generated by transitioning SDA from high to low while SCL is high. When the master has finished communicating with the slave, it issues a STOP condition. A STOP condition is generated by transitioning SDA from low to high while SCL is high. The bus is then free for communication with another SMBus device. Acknowledge The Acknowledge signal is used for handshaking between the master and the slave. An Acknowledge (active LOW) generated by the slave lets the master know that the latest byte of information was received. The Acknowledge related clock pulse is generated by the master. The master releases the SDA line (HIGH) during the Acknowledge clock pulse. The slave-receiver must pull down the SDA line during the Acknowledge clock pulse so that it remains a stable LOW during the HIGH period of this clock pulse.
U
W
U
U
Write Word Protocol The master initiates communication with the LTC1669 with a START condition and a 7-bit address followed by the Write Bit (Wr) = 0. The LTC1669 acknowledges and the master delivers the command byte. The LTC1669 acknowledges and latches the command byte into the command byte input register. The master then delivers the least significant data byte. Again the LTC1669 acknowledges and the data is latched into the least significant data byte input register. The master then delivers the most significant data byte. The LTC1669 acknowledges once more and latches the data into the most significant data byte input register. Lastly, the master terminates the communication with a STOP condition. On the reception of the STOP condition, the LTC1669 transfers the input register information to output registers and the DAC output is updated. Slave Address (MSOP Package Only) The LTC1669 can respond to one of eight 7-bit addresses. The first 4 bits (MSBs) have been factory programmed to 0100. The first 4 bits of the LTC1669-8 have been factory programmed to 0011. The three address bits, AD2, AD1 and AD0 are programmed by the user and determine the LSBs of the slave address, as shown in the table below:
LTC1669 AD2 L L L L H H H H AD1 L L H H L L H H AD0 L H L H L H L H 0100 xxx 0100 000 0100 001 0100 010 0100 011 0100 100 0100 101 0100 110 0100 111 LTC-1669-8 0011 xxx 0011 000 0011 001 0011 010 0011 011 0011 100 0011 101 0011 110 0011 111
1669f
7
LTC1669
APPLICATIONS INFORMATION
Slave Address (SOT-23 Package) The slave address for the SOT-23 package has been factory programmed to be "0100 000" (LTC1669) and "0100 001" (LTC1669-1). If another address is required, please consult the factory. Command Byte
7 X SY SD 1 0 1 0 1 0 X 6 X 5 X 4 X 3 X 2 BG 1 SD 0 SY
Allows update on Acknowledge of SYNC Address only Update on Stop condition only (Power-On Default) Puts the device in power-down mode Puts the device in standard operating mode (Power-On Default) Selects the internal bandgap reference Selects the supply as the reference (Power-On Default) Don't Care
BG X
The stop condition normally initiates the update of the DAC's output latches. Simultaneous update of more than one DAC or other devices on the bus can be achieved by reissuing new start bit, address, command and data bytes before issuing a final stop condition (which will update all the devices). An alternate way to achieve simultaneous LTC1669 updates is to override the stop condition update by setting the "SY" bit of the command byte. Setting this bit sets the device to update the DAC output latches only at the reception of a SYNC address quick command. The actual update occurs on the rising edge of SCL during the Acknowledge. In this way, all devices can update on the reception of the SYNC address quick command instead of the STOP condition. A Shutdown (SD) bit = HIGH will put the device in a low power state but retain all data latch information. Shutdown will occur at the reception of a STOP condition. This way shutdown could be synchronized to other devices. The output impedance of the DAC will go to a high impedance state ( 500k to GND).
8
U
W
U
U
The Bandgap (BG) bit when set to "0" selects the DAC supply voltage as its voltage reference. The full-scale output of the DAC with this setting is equal to the supply voltage. When the BG bit is set to "1," the internal bandgap reference (1.25V) is selected as the DAC's reference. The full-scale output voltage for this setting is 2.5V. Data Bytes
Least Significant Data Byte
7 D7 6 D6 5 D5 4 D4 3 D3 2 D2 1 D1 0 D0
Most Significant Data Byte
7 X 6 X 5 X 4 X 3 X 2 X 1 D9 0 D8
X = Don't care
Send Byte Protocol The Send Byte protocol used on the LTC1669 is actually a subset of the Write Word protocol described previously. The Send Byte protocol can only be used to send the command byte information to the LTC1669.
1 S 7 Slave Address 1 Wr 1 A 8 Command Byte 1 A 1 P
1669 TA04
S = Start Condition, Wr = Write Bit, A = Acknowledge, P = Stop Condition
The Send Byte protocol is also used whenever the Write Word protocol is interrupted for any reason. Reception of a START or STOP condition after the Acknowledge of the command byte, but before the Acknowledge of the last data byte, will cause both data bytes to be ignored and the command byte to be accepted. Reception of a START or STOP condition before the Acknowledge of the command byte will cause the interrupted command byte to be ignored.
1669f
LTC1669
APPLICATIONS INFORMATION
SYNC Address/Quick Command In addition to the slave address, the LTC1669 has an address that can be shared by other devices so that they may be updated synchronously. The address is called to the SYNC address and uses the quick command protocol. The SYNC Address is 1111 110
1 Start 7 1111 110 SYNC Address 1 SY/CLR 1 Ack 1 Stop
1669 TA05
SY/CLR
1 0
Update output latches on rising edge of SCL during Acknowledge of SYNC Address Clear all internal latches on rising edge of SCL during Acknowledge of SYNC Address
The SY/CLR bit set high only has meaning when the "SY" bit of the command byte was previously set HIGH. On the otherhand, the SY/CLR bit set LOW will always clear the part, independent of the state of the "SY" bit in the command byte. Voltage Output The output amplifier contained in the LTC1669 can source or sink up to 5mA. The output stage swings to within a few millivolts of either supply rail when unloaded and has an equivalent output resistance of 85 when driving a load to the rails. The output amplifier is stable driving capacitive loads up to 1000pF. A small resistor placed in series with the output can be used to achieve stability for any load capacitance greater than 1000pF. For example, a 0.1F load can be driven by the LTC1669 if a 110 series resistance is used. The phase margin of the resulting circuit is 45 and increases monotonically from this point if larger values of resistance, capacitance or both are substituted for the values given.
U
W
U
U
Rail-to-Rail Output Considerations As in any rail-to-rail device, the output is limited to voltages within the supply range. If the DAC offset is negative, the output for the lowest codes limits at 0V as shown in Figure 1b. Similarly, limiting can occur near full scale when VCC is used as the reference. If VREF = VCC and the DAC full-scale error (FSE) is positive, the output for the highest codes limits at VCC as shown in Figure 1c. No full-scale limiting can occur if the internal reference is used. Offset and linearity are defined and tested over the region of the DAC transfer function where no output limiting can occur. Internal Reference In applications where a predictable output is required that is independent of supply voltage, the LTC1669 has a userselectable internal reference. Selecting the internal reference will set the full-scale output voltage to 2.5V. This can be useful in applications where the supply voltage is poorly regulated. Using the LT(R)1460 Micropower Series Reference as a Power Supply for the LTC1669 In applications where the advantages of using the internal reference are required but the full-scale range needs to be greater than 2.5V, an external series reference can be used. The LT1460 is ideal for use as a power supply for the LTC1669 and can provide 3V, 3.3V and 5V full-scale output voltage ranges. The LT1460 provides accuracy, noise immunity and extended supply range to the LTC1669 when the LTC1669 is operated ratiometric to VCC. Since both parts are available in SOT-23 packages, the PC board space for this application is extremely small. See Figure 2.
1669f
9
LTC1669
APPLICATIONS INFORMATION
VREF = VCC POSITIVE FSE
OUTPUT VOLTAGE
0
OUTPUT VOLTAGE
0V NEGATIVE OFFSET INPUT CODE (b)
1669 F01
Figure 1. Effects of Rail-to-Rail Operation On a DAC Transfer Curve. (a) Overall Transfer Function (b) Effect of Negative Offset for Codes Near Zero Scale (c) Effect of Positive Full-Scale Error for Input Codes Near Full Scale When VREF = VCC
3.9V TO 20V 0.1F
1
IN
LT1460S3-3 2 OUT + GND 3 5 (4) TO P 1 (1)
LTC1669 PIN NUMBERS IN PARENTHESES REFER TO MSOP PACKAGE
Figure 2. LT1460 As Power Supply for the LTC1669
10
U
W
U
U
OUTPUT VOLTAGE
INPUT CODE (c) VREF = VCC
512 INPUT CODE (a)
1023
3V 0.01F 4 (5) VCC SCL SDA GND 2 (7)
1669 F02
LTC1669
OUT
3 (8)
0V VOUT 3V
1669f
LTC1669
PACKAGE DESCRIPTION
S5 Package 5-Lead Plastic TSOT-23
(Reference LTC DWG # 05-08-1635)
0.62 MAX 0.95 REF 2.90 BSC (NOTE 4)
3.85 MAX 2.62 REF
RECOMMENDED SOLDER PAD LAYOUT PER IPC CALCULATOR
0.20 BSC 1.00 MAX DATUM `A'
0.30 - 0.50 REF 0.09 - 0.20 (NOTE 3) NOTE: 1. DIMENSIONS ARE IN MILLIMETERS 2. DRAWING NOT TO SCALE 3. DIMENSIONS ARE INCLUSIVE OF PLATING 4. DIMENSIONS ARE EXCLUSIVE OF MOLD FLASH AND METAL BURR 5. MOLD FLASH SHALL NOT EXCEED 0.254mm 6. JEDEC PACKAGE REFERENCE IS MO-193
0.889 0.127 (.035 .005)
5.23 (.206) MIN
3.20 - 3.45 (.126 - .136)
0.42 0.038 (.0165 .0015) TYP
0.65 (.0256) BSC
RECOMMENDED SOLDER PAD LAYOUT DETAIL "A" 0.18 (.007) NOTE: 1. DIMENSIONS IN MILLIMETER/(INCH) 2. DRAWING NOT TO SCALE 3. DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.152mm (.006") PER SIDE 4. DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS. INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.152mm (.006") PER SIDE 5. LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING) SHALL BE 0.102mm (.004") MAX
Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
U
1.22 REF
1.4 MIN
2.80 BSC
1.50 - 1.75 (NOTE 4)
PIN ONE 0.30 - 0.45 TYP 5 PLCS (NOTE 3)
0.95 BSC
0.80 - 0.90 0.01 - 0.10
1.90 BSC
S5 TSOT-23 0302
MS8 Package 8-Lead Plastic MSOP
(Reference LTC DWG # 05-08-1660)
3.00 0.102 (.118 .004) (NOTE 3) 0.52 (.0205) REF
8
7 65
0.254 (.010) GAUGE PLANE
DETAIL "A" 0 - 6 TYP
4.90 0.152 (.193 .006)
3.00 0.102 (.118 .004) (NOTE 4)
0.53 0.152 (.021 .006)
1 1.10 (.043) MAX
23
4 0.86 (.034) REF
SEATING PLANE
0.22 - 0.38 (.009 - .015) TYP
0.65 (.0256) BSC
0.127 0.076 (.005 .003)
MSOP (MS8) 0603
1669f
11
LTC1669
TYPICAL APPLICATION
Program Up to 16 Control Outputs Per BUS and Place Them Where They Are Needed
VCC = 2.7V TO 5.5V 1 VCC SMBus 1 LTC1694 SMBus 2 GND 2
SCL P SDA
RELATED PARTS
PART NUMBER LTC1694 LTC1694-1 DACs LTC1659 LTC1660/LTC1664 LTC1661 LTC1663 ADCs LTC1285/LTC1288 LTC1286/LTC1298 8-Pin SO, 3V Micropower ADCs 8-Pin SO, 5V Micropower ADCs 1- or 2-Channel, Autoshutdown 1- or 2-Channel, Autoshutdown
1669f LT/TP 1103 1K * PRINTED IN THE USA
DESCRIPTION SMBus/I2C Accelerator SMBus/I2C Accelerator Single Rail-to-Rail 12-Bit VOUT DAC in 8-Lead MSOP Package. VCC = 2.7V to 5.5V
Octal/Quad 10-Bit VOUT DACs in 16-Pin Narrow SSOP VCC = 2.7V to 5.5V Micropower Rail-to-Rail Output. 3-Wire Interface. Dual 10-Bit VOUT in 8-Lead MSOP Package VCC = 2.7V to 5.5V Micropower Rail-to-Rail Output. 3-Wire Interface. 10-Bit VOUT in SOT-23, SMBUS Interface Pin-for-Pin Compatible with LTC1669
12
Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900 q FAX: (408) 434-0507
q
U
5 4
+
0.1F
+ 5 4 VCC SCL 1 SDA 8 LTC1669CMS8 6 VOUT AD0 2 AD1 3 GND AD2
7
0.1F CONTROL OUTPUT 0 0V VOUT0 < VCC
+ 5 4 VCC SCL 1 SDA 8 LTC1669CMS8 6 VOUT AD0 2 AD1 3 AD2 GND
7
0.1F CONTROL OUTPUT 1 0V VOUT1 < VCC
+ 5 4 VCC SCL 1 SDA 8 LTC1669-8CMS8 6 VOUT AD0 2 AD1 3 AD2 GND
2 TO OTHER I C DEVICES
0.1F CONTROL OUTPUT 15 0V VOUT15 < VCC
7
1669 TA06
COMMENTS Dual SMBus Accelerator with Active AC and DC Pull-Up Current Sources Dual SMBus Accelerator with Active AC Pull-Up Current Only Low Power Multiplying VOUT DAC. Output Swings from GND to REF. REF Input Can Be Tied to VCC. 3-Wire Interface.
www.linear.com
(c) LINEAR TECHNOLOGY CORPORATION 2003


▲Up To Search▲   

 
Price & Availability of LTC1669

All Rights Reserved © IC-ON-LINE 2003 - 2022  

[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy]
Mirror Sites :  [www.datasheet.hk]   [www.maxim4u.com]  [www.ic-on-line.cn] [www.ic-on-line.com] [www.ic-on-line.net] [www.alldatasheet.com.cn] [www.gdcy.com]  [www.gdcy.net]


 . . . . .
  We use cookies to deliver the best possible web experience and assist with our advertising efforts. By continuing to use this site, you consent to the use of cookies. For more information on cookies, please take a look at our Privacy Policy. X