 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| FUJITSU SEMICONDUCTOR DATA SHEET DS05-20846-4E FLASH MEMORY CMOS 16M (2M x 8/1M x 16) BIT MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 s FEATURES * Single 3.0 V read, program and erase Minimizes system level power requirements * Compatible with JEDEC-standard commands Uses same software commands as E2PROMs * Compatible with JEDEC-standard world-wide pinouts 48-pin TSOP (I) (Package suffix: PFTN-Normal Bend Type, PFTR-Reversed Bend Type) 46-pin SON (Package suffix: PN) 48-pin CSOP (Package suffix: PCV) 48-ball FBGA (Package suffix: PBT) * Minimum 100,000 program/erase cycles * High performance 80 ns maximum access time * Sector erase architecture One 8K word, two 4K words, one 16K word, and thirty-one 32K words sectors in word mode One 16K byte, two 8K bytes, one 32K byte, and thirty-one 64K bytes sectors in byte mode Any combination of sectors can be concurrently erased. Also supports full chip erase * Boot Code Sector Architecture T = Top sector B = Bottom sector * Embedded EraseTM Algorithms Automatically pre-programs and erases the chip or any sector * Embedded programTM Algorithms Automatically programs and verifies data at specified address * Data Polling and Toggle Bit feature for detection of program or erase cycle completion * Ready/Busy output (RY/BY) Hardware method for detection of program or erase cycle completion * Automatic sleep mode When addresses remain stable, automatically switches themselves to low power mode * Low VCC write inhibit 2.5 V (Continued) Embedded EraseTM and Embedded ProgramTM are trademarks of Advanced Micro Devices, Inc. MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 (Continued) * Erase Suspend/Resume Suspends the erase operation to allow a read data and/or program in another sector within the same device * Sector protection Hardware method disables any combination of sectors from program or erase operations * Sector Protection set function by Extended sector Protect command * Temporary sector unprotection Temporary sector unprotection via the RESET pin * In accordance with CFI (Common Flash Memory Interface) s PACKAGE 48-pin plastic TSOP (I) Marking Side 46-pin plastic SON Marking Side (FPT-48P-M19) (FPT-48P-M20) (LCC-46P-M02) 48-pin plastic CSOP 48-pin plastic FBGA (LCC-48P-M03) (BGA-48P-M03) (BGA-48P-M13) 2 MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 s GENERAL DESCRIPTION The MBM29LV160T/B is a 16M-bit, 3.0 V-only Flash memory organized as 2M bytes of 8 bits each or 1M words of 16 bits each. The MBM29LV160T/B is offered in a 48-pin TSOP (I), 46-pin SON, 48-pin CSOP and 48-ball FBGA packages. The device is designed to be programmed in-system with the standard system 3.0 V VCC supply. 12.0 V VPP and 5.0 V VCC are not required for write or erase operations. The device can also be reprogrammed in standard EPROM programmers. The standard MBM29LV160T/B offers access times of 80 ns and 120 ns, allowing operation of high-speed microprocessors without wait states. To eliminate bus contention the device has separate chip enable (CE), write enable (WE), and output enable (OE) controls. The MBM29LV160T/B is pin and command set compatible with JEDEC standard E2PROMs. Commands are written to the command register using standard microprocessor write timings. Register contents serve as input to an internal state-machine which controls the erase and programming circuitry. Write cycles also internally latch addresses and data needed for the programming and erase operations. Reading data out of the device is similar to reading from 5.0 V and 12.0 V Flash or EPROM devices. The MBM29LV160T/B is programmed by executing the program command sequence. This will invoke the Embedded Program Algorithm which is an internal algorithm that automatically times the program pulse widths and verifies proper cell margins. Typically, each sector can be programmed and verified in about 0.5 seconds. Erase is accomplished by executing the erase command sequence. This will invoke the Embedded Erase Algorithm which is an internal algorithm that automatically preprograms the array if it is not already programmed before executing the erase operation. During erase, the device automatically times the erase pulse widths and verifies proper cell margins. Any individual sector is typically erased and verified in 1.0 second. (If already preprogrammed.) The device also features a sector erase architecture. The sector mode allows each sector to be erased and reprogrammed without affecting other sectors. The MBM29LV160T/B is erased when shipped from the factory. The device features single 3.0 V power supply operation for both read and write functions. Internally generated and regulated voltages are provided for the program and erase operations. A low VCC detector automatically inhibits write operations on the loss of power. The end of program or erase is detected by Data Polling of DQ7, by the Toggle Bit feature on DQ6, or the RY/BY output pin. Once the end of a program or erase cycle has been comleted, the device internally resets to the read mode. The MBM29LV160T/B also has a hardware RESET pin. When this pin is driven low, execution of any Embedded Program Algorithm or Embedded Erase Algorithm is terminated. The internal state machine is then reset to the read mode. The RESET pin may be tied to the system reset circuitry. Therefore, if a system reset occurs during the Embedded Program Algorithm or Embedded Erase Algorithm, the device is automatically reset to the read mode and will have erroneous data stored in the address locations being programmed or erased. These locations need re-writing after the Reset. Resetting the device enables the system's microprocessor to read the boot-up firmware from the Flash memory. Fujitsu's Flash technology combines years of Flash memory manufacturing experience to produce the highest levels of quality, reliability, and cost effectiveness. The MBM29LV160T/B memory electrically erases all bits within a sector simultaneously via Fowler-Nordhiem tunneling. The bytes/words are programmed one byte/word at a time using the EPROM programming mechanism of hot electron injection. 3 MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 s FLEXIBLE SECTOR-ERASE ARCHITECTURE * * * * One 8K word, two 4K words, one 16K word, and thirty-one 32K words sectors in word mode. One 16K byte, two 8K bytes, one 32K byte, and thirty-one 64K bytes sectors in byte mode. Individual-sector, multiple-sector, or bulk-erase capability. Individual or multiple-sector protection is user definable. Sector SA0 SA1 SA2 SA3 SA4 SA5 SA6 SA7 SA8 SA9 SA10 SA11 SA12 SA13 SA14 SA15 SA16 SA17 SA18 SA19 SA20 SA21 SA22 SA23 SA24 SA25 SA26 SA27 SA28 SA29 SA30 SA31 SA32 SA33 SA34 Sector Size 64 Kbytes or 32 Kwords 64 Kbytes or 32 Kwords 64 Kbytes or 32 Kwords 64 Kbytes or 32 Kwords 64 Kbytes or 32 Kwords 64 Kbytes or 32 Kwords 64 Kbytes or 32 Kwords 64 Kbytes or 32 Kwords 64 Kbytes or 32 Kwords 64 Kbytes or 32 Kwords 64 Kbytes or 32 Kwords 64 Kbytes or 32 Kwords 64 Kbytes or 32 Kwords 64 Kbytes or 32 Kwords 64 Kbytes or 32 Kwords 64 Kbytes or 32 Kwords 64 Kbytes or 32 Kwords 64 Kbytes or 32 Kwords 64 Kbytes or 32 Kwords 64 Kbytes or 32 Kwords 64 Kbytes or 32 Kwords 64 Kbytes or 32 Kwords 64 Kbytes or 32 Kwords 64 Kbytes or 32 Kwords 64 Kbytes or 32 Kwords 64 Kbytes or 32 Kwords 64 Kbytes or 32 Kwords 64 Kbytes or 32 Kwords 64 Kbytes or 32 Kwords 64 Kbytes or 32 Kwords 64 Kbytes or 32 Kwords 32 Kbytes or 16 Kwords 8 Kbytes or 4 Kwords 8 Kbytes or 4 Kwords 16 Kbytes or 8 Kwords (x 8) Address Range 00000H to 0FFFFH 10000H to 1FFFFH 20000H to 2FFFFH 30000H to 3FFFFH 40000H to 4FFFFH 50000H to 5FFFFH 60000H to 6FFFFH 70000H to 7FFFFH 80000H to 8FFFFH 90000H to 9FFFFH A0000H to AFFFFH B0000H to BFFFFH C0000H to CFFFFH D0000H to DFFFFH E0000H to EFFFFH F0000H to FFFFFH 100000H to 10FFFFH 110000H to 11FFFFH 120000H to 12FFFFH 130000H to 13FFFFH 140000H to 14FFFFH 150000H to 15FFFFH 160000H to 16FFFFH 170000H to 17FFFFH 180000H to 18FFFFH 190000H to 19FFFFH 1A0000H to 1AFFFFH 1B0000H to 1BFFFFH 1C0000H to 1CFFFFH 1D0000H to 1DFFFFH 1E0000H to 1EFFFFH 1F0000H to 1F7FFFH 1F8000H to 1F9FFFH 1FA000H to 1FBFFFH 1FC000H to 1FFFFFH (x 16) Address Range 00000H to 07FFFH 08000H to 0FFFFH 10000H to 17FFFH 18000H to 1FFFFH 20000H to 27FFFH 28000H to 2FFFFH 30000H to 37FFFH 38000H to 3FFFFH 40000H to 47FFFH 48000H to 4FFFFH 50000H to 57FFFH 58000H to 5FFFFH 60000H to 67FFFH 68000H to 6FFFFH 70000H to 77FFFH 78000H to 7FFFFH 80000H to 87FFFH 88000H to 8FFFFH 90000H to 97FFFH 98000H to 9FFFFH A0000H to A7FFFH A8000H to AFFFFH B0000H to B7FFFH B8000H to BFFFFH C0000H to C7FFFH C8000H to CFFFFH D0000H to D7FFFH D8000H to DFFFFH E0000H to E7FFFH E8000H to EFFFFH F0000H to F7FFFH F8000H to FBFFFH FC000H to FCFFFH FD000H to FDFFFH FE000H to FFFFFH MBM29LV160T Top Boot Sector Architecture 4 MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 Sector SA0 SA1 SA2 SA3 SA4 SA5 SA6 SA7 SA8 SA9 SA10 SA11 SA12 SA13 SA14 SA15 SA16 SA17 SA18 SA19 SA20 SA21 SA22 SA23 SA24 SA25 SA26 SA27 SA28 SA29 SA30 SA31 SA32 SA33 SA34 Sector Size 16 Kbytes or 8 Kwords 8 Kbytes or 4 Kwords 8 Kbytes or 4 Kwords 32 Kbytes or 16 Kwords 64 Kbytes or 32 Kwords 64 Kbytes or 32 Kwords 64 Kbytes or 32 Kwords 64 Kbytes or 32 Kwords 64 Kbytes or 32 Kwords 64 Kbytes or 32 Kwords 64 Kbytes or 32 Kwords 64 Kbytes or 32 Kwords 64 Kbytes or 32 Kwords 64 Kbytes or 32 Kwords 64 Kbytes or 32 Kwords 64 Kbytes or 32 Kwords 64 Kbytes or 32 Kwords 64 Kbytes or 32 Kwords 64 Kbytes or 32 Kwords 64 Kbytes or 32 Kwords 64 Kbytes or 32 Kwords 64 Kbytes or 32 Kwords 64 Kbytes or 32 Kwords 64 Kbytes or 32 Kwords 64 Kbytes or 32 Kwords 64 Kbytes or 32 Kwords 64 Kbytes or 32 Kwords 64 Kbytes or 32 Kwords 64 Kbytes or 32 Kwords 64 Kbytes or 32 Kwords 64 Kbytes or 32 Kwords 64 Kbytes or 32 Kwords 64 Kbytes or 32 Kwords 64 Kbytes or 32 Kwords 64 Kbytes or 32 Kwords (x 8) Address Range 00000H to 03FFFH 04000H to 05FFFH 06000H to 07FFFH 08000H to 0FFFFH 10000H to 1FFFFH 20000H to 2FFFFH 30000H to 3FFFFH 40000H to 4FFFFH 50000H to 5FFFFH 60000H to 6FFFFH 70000H to 7FFFFH 80000H to 8FFFFH 90000H to 9FFFFH A0000H to AFFFFH B0000H to BFFFFH C0000H to CFFFFH D0000H to DFFFFH E0000H to EFFFFH F0000H to FFFFFH 100000H to 10FFFFH 110000H to 11FFFFH 120000H to 12FFFFH 130000H to 13FFFFH 140000H to 14FFFFH 150000H to 15FFFFH 160000H to 16FFFFH 170000H to 17FFFFH 180000H to 18FFFFH 190000H to 19FFFFH 1A0000H to 1AFFFFH 1B0000H to 1BFFFFH 1C0000H to 1CFFFFH 1D0000H to 1DFFFFH 1E0000H to 1EFFFFH 1F0000H to 1FFFFFH (x 16) Address Range 00000H to 01FFFH 02000H to 02FFFH 03000H to 03FFFH 04000H to 07FFFH 08000H to 0FFFFH 10000H to 17FFFH 18000H to 1FFFFH 20000H to 27FFFH 28000H to 2FFFFH 30000H to 37FFFH 38000H to 3FFFFH 40000H to 47FFFH 48000H to 4FFFFH 50000H to 57FFFH 58000H to 5FFFFH 60000H to 67FFFH 68000H to 6FFFFH 70000H to 77FFFH 78000H to 7FFFFH 80000H to 87FFFH 88000H to 8FFFFH 90000H to 97FFFH 98000H to 9FFFFH A0000H to A7FFFH A8000H to AFFFFH B0000H to B7FFFH B8000H to BFFFFH C0000H to C7FFFH C8000H to CFFFFH D0000H to D7FFFH D8000H to DFFFFH E0000H to E7FFFH E8000H to EFFFFH F0000H to F7FFFH F8000H to FFFFFH MBM29LV160B Bottom Boot Sector Architecture 5 MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 s PRODUCT LINE UP Part No. VCC = 3.3 V Ordering Part No. VCC = 3.0 V Max. Address Access Time (ns) Max. CE Access Time (ns) Max. OE Access Time (ns) +0.3 V -0.3 V +0.6 V -0.3 V MBM29LV160T/160B -80 -- 80 80 30 -- -90 90 90 35 -- -12 120 120 50 s BLOCK DIAGRAM RY/BY Buffer VCC VSS DQ0 to DQ15 RY/BY Erase Voltage Generator Input/Output Buffers WE BYTE RESET State Control Command Register Program Voltage Generator CE OE Chip Enable Output Enable Logic STB Data Latch STB Y-Decoder Y-Gating Low VCC Detector Timer for Program/Erase Address Latch X-Decoder Cell Matrix A0 to A19 A-1 6 MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 s CONNECTION DIAGRAMS TSOP(I) A15 A14 A13 A12 A11 A10 A9 A8 A19 N.C. WE RESET N.C. N.C. RY/BY A18 A17 A7 A6 A5 A4 A3 A2 A1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 (Marking Side) 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 A16 BYTE VSS DQ15/A-1 DQ7 DQ14 DQ6 DQ13 DQ5 DQ12 DQ4 VCC DQ11 DQ3 DQ10 DQ2 DQ9 DQ1 DQ8 DQ0 OE VSS CE A0 Standard Pinout FPT-48P-M19 A1 A2 A3 A4 A5 A6 A7 A17 A18 RY/BY N.C. N.C. RESET WE N.C. A19 A8 A9 A10 A11 A12 A13 A14 A15 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 (Marking Side) 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 A0 CE VSS OE DQ0 DQ8 DQ1 DQ9 DQ2 DQ10 DQ3 DQ11 VCC DQ4 DQ12 DQ5 DQ13 DQ6 DQ14 DQ7 DQ15/A-1 VSS BYTE A16 Reverse Pinout FPT-48P-M20 (TOP VIEW) A13 A14 A15 A12 A11 A10 A9 A8 A19 WE RESET VCC DQ4 DQ12 DQ5 DQ13 DQ6 DQ14 DQ7 A16 BYTE VSS DQ15/A-1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 (Marking Side) 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 A3 A2 A1 A4 A5 A6 A7 A17 A18 RY/BY N.C. DQ11 DQ3 DQ10 DQ2 DQ9 DQ1 DQ8 DQ0 A0 CE VSS OE SON-46 LCC- 46P-M02 (Continued) 7 MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 (Continued) (TOP VIEW) A1 A2 A3 A4 A5 A6 A7 A17 A18 RY/BY N.C. N.C. RESET WE N.C. A19 A8 A9 A10 A11 A12 A13 A14 A15 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 A0 CE VSS OE DQ0 DQ8 DQ1 DQ9 DQ2 DQ10 DQ3 DQ11 VCC DQ4 DQ12 DQ5 DQ13 DQ6 DQ14 DQ7 DQ15/A-1 VSS BYTE A16 CSOP-48 LCC-48P-M03 FBGA (TOP VIEW) Marking side A1 B1 C1 D1 E1 F1 G1 H1 A2 B2 C2 D2 E2 F2 G2 H2 A3 B3 C3 D3 E3 F3 G3 H3 A4 B4 C4 D4 E4 F4 G4 H4 A5 B5 C5 D5 E5 F5 G5 H5 A6 B6 C6 D6 E6 F6 G6 H6 (BGA-48P-M03) (BGA-48P-M13) A1 B1 C1 D1 E1 F1 G1 H1 A3 A4 A2 A1 A0 CE OE VSS A2 B2 C2 D2 E2 F2 G2 H2 A7 A17 A6 A5 DQ0 DQ8 DQ9 DQ1 A3 B3 C3 D3 E3 F3 G3 H3 RY/BY N.C. A18 N.C. DQ2 DQ10 DQ11 DQ3 A4 B4 C4 D4 E4 F4 G4 H4 WE RESET N.C. A19 DQ5 DQ12 VCC DQ4 A5 B5 C5 D5 E5 F5 G5 H5 A9 A8 A10 A11 DQ7 DQ14 DQ13 DQ6 A6 B6 C6 D6 E6 F6 G6 H6 A13 A12 A14 A15 A16 BYTE DQ15/A-1 VSS 8 MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 s LOGIC SYMBOL Table 1 MBM29LV160T/B Pin Configuration Pin A-1 20 A0 to A19 DQ0 to DQ15 CE OE WE RESET BYTE RY/BY 16 or 8 Function Address Inputs Data Inputs/Outputs Chip Enable Output Enable Write Enable Ready/Busy Output Hardware Reset Pin/ Temporary Sector Unprotection Selects 8-bit or 16-bit mode Pin Not Connected Internally Device Ground Device Power Supply A-1, A0 to A19 DQ0 to DQ15 CE OE WE RY/BY RESET BYTE N.C. VSS VCC 9 MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 Table 2 Operation Auto-Select Manufacture Code (1) Auto-Select Device Code (1) Read (3) Standby Output Disable Write (Program/Erase) Enable Sector Protection (2), (4) Verify Sector Protection (2), (4) Temporary Sector Unprotection (5) Reset (Hardware)/Standby Table 3 Operation Auto-Select Manufacture Code (1) Auto-Select Device Code (1) Read (3) Standby Output Disable Write (Program/Erase) Enable Sector Protection (2), (4) Verify Sector Protection (2), (4) Temporary Sector Unprotection (5) Reset (Hardware)/Standby MBM29LV160T/B User Bus Operation (BYTE = VIH) CE L L L H L L L L X X OE L L L X H H VID L X X H X X WE H H H X H L A0 L H A0 X X A0 L L X X A1 L L A1 X X A1 H H X X A6 L L A6 X X A6 L L X X A9 VID VID A9 X X A9 VID VID X X DQ0 to DQ15 RESET Code Code DOUT HIGH-Z HIGH-Z DIN X Code X HIGH-Z H H H H H H H H VID L MBM29LV160T/B User Bus Operation (BYTE = VIL) CE L L L H L L L L X X OE L L L X H H VID L X X H X X WE DQ15 /A-1 H H H X H L L L A-1 X X A-1 L L X X A0 L H A0 X X A0 L L X X A1 L L A1 X X A1 H H X X A6 L L A6 X X A6 L L X X A9 VID VID A9 X X A9 VID VID X X DQ0 to DQ7 Code Code DOUT HIGH-Z HIGH-Z DIN X Code X HIGH-Z RESET H H H H H H H H VID L Legend: L = VIL, H = VIH, X = VIL or VIH. = pulse input. See DC Characteristics for voltage levels. Notes: 1. Manufacturer and device codes may also be accessed via a command register write sequence. See Table 7. 2. Refer to the section on Sector Protection. 3. WE can be VIL if OE is VIL, OE at VIH initiates the write operations. 4. VCC = 3.3 V 10% 5. It is also used for the extended sector protection. 10 MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 s ORDERING INFORMATION Standard Products Fujitsu standard products are available in several packages. The order number is formed by a combination of: MBM29LV160 T -80 PFTN PACKAGE TYPE PFTN = 48-Pin Thin Small Outline Package (TSOP) Standard Pinout PFTR = 48-Pin Thin Small Outline Package (TSOP) Reverse Pinout PN PCV PBT =46-Pin Small Outline Nonleaded Package (SON) = 48-Pin C- leaded Small Outline Package (CSOP) = 48-Pin Fine Pitch Ball Grid Array Package (FBGA:BGA-48P-M03) PBT- SF2= 48-Pin Fine Pitch Ball Grid Array Package (FBGA:BGA-48P-M13) SPEED OPTION See Product Selector Guide BOOT CODE SECTOR ARCHITECTURE T = Top sector B = Bottom sector DEVICE NUMBER/DESCRIPTION MBM29LV160 16 Mega-bit (2M x 8-Bit or 1M x 16-Bit) CMOS Flash Memory 3.0 V-only Read, Write, and Erase 11 MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 s FUNCTIONAL DESCRIPTION Read Mode The MBM29LV160T/B has two control functions which must be satisfied in order to obtain data at the outputs. CE is the power control and should be used for a device selection. OE is the output control and should be used to gate data to the output pins if a device is selected. Address access time (tACC) is equal to the delay from stable addresses to valid output data. The chip enable access time (tCE) is the delay from stable addresses and stable CE to valid data at the output pins. The output enable access time is the delay from the falling edge of OE to valid data at the output pins. (Assuming the addresses have been stable for at least tACC - tOE time.) See Figure 5.1 for timing specifications. Standby Mode There are two ways to implement the standby mode on the MBM29LV160T/B devices. One is by using both the CE and RESET pins; the other via the RESET pin only. When using both pins, a CMOS standby mode is achieved with CE and RESET inputs both held at VCC 0.3 V. Under this condition the current consumed is less than 5 A max. During Embedded Algorithm operation, VCC Active current (ICC2) is required even CE = "H". The device can be read with standard access time (tCE) from either of these standby modes. When using the RESET pin only, a CMOS standby mode is achieved with the RESET input held at VSS 0.3 V (CE = "H" or "L"). Under this condition the current consumed is less than 5 A max. Once the RESET pin is taken high, the device requires tRH of wake up time before outputs are valid for read access. In the standby mode, the outputs are in the high-impedance state, independent of the OE input. Automatic Sleep Mode There is a function called automatic sleep mode to restrain power consumption during read-out of MBM29LV160T/B data. This mode can be used effectively with an application requesting low power consumption such as handy terminals. To activate this mode, MBM29LV160T/B automatically switches itself to low power mode when addresses remain stable for 150 ns. It is not necessary to control CE, WE, and OE in this mode. During such mode, the current consumed is typically 1 A (CMOS Level). Standard address access timings provide new data when addresses are changed. While in sleep mode, output data is latched and always available to the system. Output Disable If the OE input is at a logic high level (VIH), output from the device is disabled. This will cause the output pins to be in a high-impedance state. Autoselect The Autoselect mode allows the reading out of a binary code from the device and will identify its manufacturer and type. The intent is to allow programming equipment to automatically match the device to be programmed with its corresponding programming algorithm. The Autoselect command may also be used to check the status of write-protected sectors. (See Tables 4.1 and 4.2.) This mode is functional over the entire temperature range of the device. To activate this mode, the programming equipment must force VID (11.5 V to 12.5 V) on address pin A9. Two identifier bytes may then be sequenced from the devices outputs by toggling address A0 from VIL to VIH. All addresses are DON'T CARES except A0, A1, and A6 (A-1). (See Table 2 or Table 3.) 12 MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 The manufacturer and device codes may also be read via the command register, for instances when the MBM29LV160T/B is erased or programmed in a system without access to high voltage on the A9 pin. The command sequence is illustrated in Table 7, Command Definitions. Byte 0 (A0 = VIL) represents the manufacture's code and byte 1 (A0 = VIH) represents the device identifier code. For the MBM29LV160T/B these two bytes are given in the Table 4.2. All identifiers for manufactures and device will exhibit odd parity with DQ7 defined as the parity bit. In order to read the proper device codes when executing the Autoselect, A1 must be VIL. (See Tables 2 or 3.) For device indentification in word mode (BYTE = VIH), DQ9 and DQ13 are equal to `1' and DQ8, DQ10 to DQ12, DQ14, and DQ15 are equal to `0'. If BYTE = VIL (for byte mode), the device code is C4H (for top boot block) or 49H (for bottom boot block). If BYTE = VIH (for word mode), the device code is 22C4H (for top boot block) or 2249H (for bottom boot block). In order to determine which sectors are write protected, A1 must be at VIH while running through the sector addresses; if the selected sector is protected, a logical `1' will be output on DQ0 (DQ0 =1). Table 4.1 MBM29LV160T/B Sector Protection Verify Autoselect Code Type Manufacture's Code Byte MBM29LV160T Word Device Code Byte MBM29LV160B Word Sector Protection *1: A-1 is for Byte mode. *2: Outputs 01H at protected sector addresses and outputs 00H at unprotected sector addresses. Table 4.2 Expanded Autoselect Code Table Type Manufacture's Code (B) MBM29LV160T A12 to A18 X X A6 VIL VIL A1 VIL VIL A0 VIL VIH A-1*1 VIL VIL X VIL Code (HEX) 04H C4H 22C4H 49H 2249H 01H*2 X Sector Addresses VIL VIL VIH X VIL VIH VIL VIL Code DQ15 DQ14 DQ13 DQ12 DQ11 DQ10 DQ9 DQ8 DQ7 DQ6 DQ5 DQ4 DQ3 DQ2 DQ1 DQ0 04H A-1/0 0 0 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 0 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 C4H A-1 HI-Z HI-Z HI-Z HI-Z HI-Z HI-Z HI-Z 1 0 0 1 0 0 0 1 0 1 Device Code MBM29LV160B (W) 22C4H (B) 49H A-1 HI-Z HI-Z HI-Z HI-Z HI-Z HI-Z HI-Z 0 0 0 0 1 0 0 0 0 0 0 0 1 0 0 0 0 0 (W) 2249H Sector Protection (B): Byte mode (W): Word mode 01H A-1/0 13 MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 Table 5 Sector Address SA0 SA1 SA2 SA3 SA4 SA5 SA6 SA7 SA8 SA9 SA10 SA11 SA12 SA13 SA14 SA15 SA16 SA17 SA18 SA19 SA20 SA21 SA22 SA23 SA24 SA25 SA26 SA27 SA28 SA29 SA30 SA31 SA32 SA33 SA34 A19 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 A18 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 A17 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 1 1 1 A16 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 1 1 1 Sector Address Tables (MBM29LV160T) A15 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 1 1 1 A14 X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X 0 1 1 1 A13 X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X 0 0 1 A12 X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X 0 1 X (x 8) Address Range 00000H to 0FFFFH 10000H to 1FFFFH 20000H to 2FFFFH 30000H to 3FFFFH 40000H to 4FFFFH 50000H to 5FFFFH 60000H to 6FFFFH 70000H to 7FFFFH 80000H to 8FFFFH 90000H to 9FFFFH A0000H to AFFFFH B0000H to BFFFFH C0000H to CFFFFH D0000H to DFFFFH E0000H to EFFFFH F0000H to FFFFFH 100000H to 10FFFFH 110000H to 11FFFFH 120000H to 12FFFFH 130000H to 13FFFFH 140000H to 14FFFFH 150000H to 15FFFFH 160000H to 16FFFFH 170000H to 17FFFFH 180000H to 18FFFFH 190000H to 19FFFFH 1A0000H to 1AFFFFH 1B0000H to 1BFFFFH 1C0000H to 1CFFFFH 1D0000H to 1DFFFFH 1E0000H to 1EFFFFH 1F0000H to 1F7FFFH 1F8000H to 1F9FFFH 1FA000H to 1FBFFFH 1FC000H to 1FFFFFH (x 16) Address Range 00000H to 07FFFH 08000H to 0FFFFH 10000H to 17FFFH 18000H to 1FFFFH 20000H to 27FFFH 28000H to 2FFFFH 30000H to 37FFFH 38000H to 3FFFFH 40000H to 47FFFH 48000H to 4FFFFH 50000H to 57FFFH 58000H to 5FFFFH 60000H to 67FFFH 68000H to 6FFFFH 70000H to 77FFFH 78000H to 7FFFFH 80000H to 87FFFH 88000H to 8FFFFH 90000H to 97FFFH 98000H to 9FFFFH A0000H to A7FFFH A8000H to AFFFFH B0000H to B7FFFH B8000H to BFFFFH C0000H to C7FFFH C8000H to CFFFFH D0000H to D7FFFH D8000H to DFFFFH E0000H to E7FFFH E8000H to EFFFFH F0000H to F7FFFH F8000H to FBFFFH FC000H to FCFFFH FD000H to FDFFFH FE000H to FEFFFH 14 MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 Table 6 Sector Address SA0 SA1 SA2 SA3 SA4 SA5 SA6 SA7 SA8 SA9 SA10 SA11 SA12 SA13 SA14 SA15 SA16 SA17 SA18 SA19 SA20 SA21 SA22 SA23 SA24 SA25 SA26 SA27 SA28 SA29 SA30 SA31 SA32 SA33 SA34 A19 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 A18 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 A17 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 A16 0 0 0 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 Sector Address Tables (MBM29LV160B) A15 0 0 0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 A14 0 0 0 1 X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X A13 0 1 1 0 X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X A12 X 0 1 X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X (x 8) Address Range 00000H to 03FFFH 04000H to 05FFFH 06000H to 07FFFH 08000H to 0FFFFH 10000H to 1FFFFH 20000H to 2FFFFH 30000H to 3FFFFH 40000H to 4FFFFH 50000H to 5FFFFH 60000H to 6FFFFH 70000H to 7FFFFH 80000H to 8FFFFH 90000H to 9FFFFH A0000H to AFFFFH B0000H to BFFFFH C0000H to CFFFFH D0000H to DFFFFH E0000H to EFFFFH F0000H to FFFFFH 100000H to 1FFFFFH 110000H to 11FFFFH 120000H to 12FFFFH 130000H to 13FFFFH 140000H to 14FFFFH 150000H to 15FFFFH 160000H to 16FFFFH 170000H to 17FFFFH 180000H to 18FFFFH 190000H to 19FFFFH 1A0000H to 1AFFFFH 1B0000H to 1BFFFFH 1C0000H to 1CFFFFH 1D0000H to 1DFFFFH 1E0000H to 1EFFFFH 1F0000H to 1FFFFFH (x 16) Address Range 00000H to 01FFFH 02000H to 02FFFH 03000H to 03FFFH 04000H to 07FFFH 08000H to 0FFFFH 10000H to 17FFFH 18000H to 1FFFFH 20000H to 27FFFH 28000H to 2FFFFH 30000H to 37FFFH 38000H to 3FFFFH 40000H to 47FFFH 48000H to 4FFFFH 50000H to 57FFFH 58000H to 5FFFFH 60000H to 67FFFH 68000H to 6FFFFH 70000H to 77FFFH 78000H to 7FFFFH 80000H to 87FFFH 88000H to 8FFFFH 90000H to 97FFFH 98000H to 9FFFFH A0000H to A7FFFH A8000H to 8FFFFH B0000H to B7FFFH B8000H to BFFFFH C0000H to C7FFFH C8000H to CFFFFH D0000H to D7FFFH D8000H to DFFFFH E0000H to E7FFFH E8000H to EFFFFH F0000H to F7FFFH F8000H to FFFFFH 15 MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 Write Device erasure and programming are accomplished via the command register. The command register is written by bringing WE to VIL, while CE is at VIL and OE is at VIH. Addresses are latched on the falling edge of CE or WE, whichever occurs later, while data is latched on the rising edge of CE or WE pulse, whichever occurs first. Standard microprocessor write timings are used. See Figures 6 to 8. Refer to AC Write Characteristics and the Erase/Programming Waveforms for specific timing parameters. Sector Protection The MBM29LV160T/B features hardware sector protection. This feature will disable both program and erase operations in any number of sectors (0 through 34). The sector protection feature is enabled using programming equipment at the user's site. The device is shipped with all sectors unprotected. To activate this mode, the programming equipment must force VID on address pin A9 and control pin OE, CE = VIL, A0 = A6 = VIL, A1 = VIH. The sector addresses pins (A19, A18, A17, A16, A15, A14, A13, and A12) should be set to the sector to be protected. Tables 5 and 6 define the sector address for each of the thirty five (35) individual sectors. Programming of the protection circuitry begins on the falling edge of the WE pulse and is terminated with the rising edge of the same. Sector addresses must be held constant during the WE pulse. See figures 16 and 24 for sector protection waveforms and algorithm. To verify programming of the protection circuitry, the programming equipment must force VID on address pin A9 with CE and OE at VIL and WE at VIH. Scanning the sector addresses (A19, A18, A17, A16, A15, A14, A13, and A12) while (A6, A1, A0) = (0, 1, 0) will produce a logical "1" at device output DQ0 for a protected sector. Otherwise the device will read 00H for an unprotected sector. In this mode, the lower order addresses, except for A0, A1, and A6 are DON'T CARES. Address locations with A1 = VIL are reserved for Autoselect manufacturer and device codes. A-1 requires to VIL in byte mode. It is also possible to determine if a sector is protected in the system by writing an Autoselect command. Performing a read operation at the address location XX02H, where the higher order addresses pins (A19, A18, A17, A16, A15, A14, A13, and A12) represents the sector address will produce a logical "1" at DQ0 for a protected sector. See Tables 4.1 and 4.2 for Autoselect codes. Temporary Sector Unprotection This feature allows temporary unprotection of previously protected sectors of the MBM29LV160T/B devices in order to change data. The Sector Unprotection mode is activated by setting the RESET pin to high voltage (12 V). During this mode, formerly protected sectors can be programmed or erased by selecting the sector addresses. Once the 12 V is taken away from the RESET pin, all the previously protected sectors will be protected again. (See Figures 18 and 25.) 16 MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 Table 7 Command Sequence (Notes 1, 2, 3, 5) Read/Reset (Note 6) Read/Reset (Note 6) Bus Write Cycles Req'd MBM29LV160T/B Standard Command Definitions Second First Bus Third Bus Fourth Bus Fifth Bus Sixth Bus Bus Write Cycle Write Cycle Write Cycle Read/Write Write Cycle Write Cycle Cycle Addr Data Addr Data Addr Data Addr Data Addr Data Addr Data XXXH F0H 555H AAAH 555H AAAH 555H AAH AAH -- 2AAH 555H 2AAH 555H 2AAH AAH 555H 2AAH 555H 2AAH 555H -- -- 55H -- 55H 55H -- 555H AAAH 555H AAAH 555H AAAH 555H AAAH 555H AAAH -- -- A0H PA 555H AAAH 555H AAAH -- -- PD -- 2AAH 555H 2AAH 555H -- -- -- -- 555H AAH SA -- -- -- -- F0H 90H -- RA -- -- RD -- -- -- -- -- -- -- -- -- -- -- -- -- Word /Byte Word Byte Word Byte 1 3 3 Autoselect Byte/Word Program (Notes 3, 4) Chip Erase Word Byte Word Byte Word Byte Word /Byte Word /Byte 4 AAAH 555H AAAH 555H AAAH 6 6 1 1 AAH AAH 55H 55H -- -- 80H 80H -- -- AAH AAH -- -- 55H 55H -- -- 10H 30H -- -- Sector Erase (Note 3) Sector Erase Suspend Sector Erase Resume XXXH B0H XXXH 30H Notes: 1. Address bits A11 to A19 = X = "H" or "L" for all address commands except or Program Address (PA) and Sector Address (SA). 2. Bus operations are defined in Tables 2 and 3. 3. RA =Address of the memory location to be read. PA =Address of the memory location to be programmed. Addresses are latched on the falling edge of the WE pulse. SA =Address of the sector to be erased. The combination of A19, A18, A17, A16, A15, A14, A13, and A12 will uniquely select any sector. 4. RD =Data read from location RA during read operation. PD =Data to be programmed at location PA. Data is latched on the rising edge of WE. 5. The system should generate the following address patterns: Word Mode: 555H or 2AAH to addresses A0 to A10 Byte Mode: AAAH or 555H to addresses A-1 to A10 6. Both Read/Reset commands are functionally equivalent, resetting the device to the read mode. 17 MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 Table 8 Command Sequence Set to Fast Mode Fast Program *1 Reset from Fast Mode *1 Query Command *2 Word Byte Word Byte Word Byte Word Byte Bus Write Cycles Req'd 3 2 2 2 4 MBM29LV160T/B Extended Command Definitions First Bus Write Cycle Addr 555H AAAH XXXH XXXH XXXH XXXH 55H AAH XXXH Data AAH A0H 90H 98H 60H Second Bus Write Cycle Addr 2AAH 555H PA XXXH XXXH -- SPA Data 55H PD F0H *4 -- 60H Third Bus Write Cycle Addr 555H AAAH -- -- -- SPA Data 20H -- -- -- 40H Fourth Bus Read Cycle Addr -- -- -- -- SPA Data -- -- -- -- SD Extended Sector Word Protect *3 Byte SPA : Sector Address to be protected. Set sector address (SA) and (A6, A1, A0) = (0, 1, 0). SD : Sector protection verify data. Output 01H at protected sector addresses and output 00H at unprotected sector addresses. *1. *2. *3. *4. This command is valid while fast mode. Addresses from system set to A0 to A6. The other addresses are "Don't care". This command is valid while VID = RESET. The data" OOH" is also acceptable. Command Definitions Device operations are selected by writing specific address and data sequences into the command register. Writing incorrect address and data values or writing them in an improper sequence will reset the device to the read mode. Table 7 defines the valid register command sequences. Note that the Erase Suspend (B0H) and Erase Resume (30H) commands are valid only while the Sector Erase operation is in progress. Moreover both Read/Reset commands are functionally equivalent, resetting the device to the read mode. Please note that commands are always written at DQ0 to DQ7 and DQ8 to DQ15 bits are ignored. Read/Reset Command In order to return from Autoselect mode or Exceeded Timing Limits (DQ5 = 1) to read mode, the read/reset operation is initiated by writing the Read/Reset command sequence into the command register. Microprocessor read cycles retrieve array data from the memory. The device remains enabled for reads until the command register contents are altered. The device will automatically power-up in the Read/Reset state. In this case, a command sequence is not required to read data. Standard microprocessor read cycles will retrieve array data. This default value ensures that no spurious alteration of the memory contents occurs during the power transition. Refer to the AC Read Characteristics and Waveforms for specific timing parameters. (See Figure 5.1.) Autoselect Command Flash memories are intended for use in applications where the local CPU alters memory contents. As such, manufactures and device codes must be accessible while the device resides in the target system. PROM programmers typically access the signature codes by raising A9 to a high voltage. However, multiplexing high voltage onto the address lines is not generally desired system design practice. 18 MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 The device contains an Autoselect command operation to supplement traditional PROM programming methodology. The operation is initiated by writing the Autoselect command sequence into the command register. Following the last command write, a read cycle from address XX00H retrieves the manufacture code of 04H. A read cycle from address XX01H for x16 (XX02H for x8) retrieves the device code (MBM29LV160T = C4H and MBM29LV160B = 49H for x8 mode; MBM29LV160T = 22C4H and MBM29LV160B = 2249H for x16 mode). (See Tables 4.1 and 4.2.) All manufactures and device codes will exhibit odd parity with DQ7 defined as the parity bit. The sector state (protection or unprotection) will be indicated by address XX02H for x16 (XX04H for x8). Scanning the sector addresses (A19, A18, A17, A16, A15, A14, A13, and A12) while (A6, A1, A0) = (0, 1, 0) will produce a logical "1" at device output DQ0 for a protected sector. The programming verification should be perform margin mode verification on the protected sector. (See Tables 2 and 3.) To terminate the operation, it is necessary to write the Read/Reset command sequence into the register and, also to write the Autoselect command during the operation, by executing it after writing the Read/Reset command sequence. Word/Byte Programming The device is programmed on a byte-by-byte (or word-by-word) basis. Programming is a four bus cycle operation. There are two "unlock" write cycles. These are followed by the program set-up command and data write cycles. Addresses are latched on the falling edge of CE or WE, whichever happens later and the data is latched on the rising edge of CE or WE, whichever happens first. The rising edge of the last CE or WE (whichever happens first) begins programming. Upon executing the Embedded Program Algorithm command sequence, the system is not required to provide further controls or timings. The device will automatically provide adequate internally generated program pulses and verify the programmed cell margin. (See Figures 6 and 7.) The automatic programming operation is completed when the data on DQ7 is equivalent to data written to this bit at which time the device return to the read mode and addresses are no longer latched. (See Table 8, Hardware Sequence Flags.) Therefore, the device requires that a valid address be supplied by the system at this time. Hence, Data Polling must be performed at the memory location which is being programmed. Any commands written to the chip during this period will be ignored. If hardware reset occures during the programming operation, it is impossible to guarantee whether the data being written is correct or not. Programming is allowed in any sequence and across sector boundaries. Beware that a data "0" cannot be programmed back to a "1". Attempting to do so may either hang up the device or result in an apparent success according to the data polling algorithm but a read from read/reset mode will show that the data is still "0". Only erase operations can convert "0"s to "1"s. Figure 20 illustrates the Embedded ProgramTM Algorithm using typical command strings and bus operations. Chip Erase Chip erase is a six-bus cycle operation. There are two "unlock" write cycles. These are followed by writing the "set-up" command. Two more "unlock" write cycles are then followed by the chip erase command. Chip erase does not require the user to program the device prior to erase. Upon executing the Embedded Erase Algorithm command sequence the device will automatically program and verify the entire memory for an all zero data pattern prior to electrical erase. (Preprogram Function.) The system is not required to provide any controls or timings during these operations. The automatic erase begins on the rising edge of the last WE pulse in the command sequence and terminates when the data on DQ7 is "1" (See Write Operation Status section.) at which time the device returns to read mode. (See Figure 8.) Figure 21 illustrates the Embedded EraseTM Algorithm using typical command strings and bus operations. Sector Erase 19 MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 Sector erase is a six-bus cycle operation. There are two "unlock" write cycles, followed by writing the "set-up" command. Two more "unlock" write cycles are then followed by the Sector Erase command. The sector address (any address location within the desired sector) is latched on the falling edge of WE, while the command (Data = 30H) is latched on the rising edge of WE. After a time-out of 50 s from the rising edge of the last sector erase command, the sector erase operation will begin. Multiple sectors may be erased concurrently by writing six-bus cycle operations on Table 7. This sequence is followed with writes of the Sector Erase command to addresses in other sectors desired to be concurrently erased. The time between writes must be less than 50 s otherwise that command will not be accepted and erasure will start. It is recommended that processor interrupts be disabled during this time to guarantee this condition. The interrupts can be re-enabled after the last Sector Erase command is written. A time-out of 50 s from the rising edge of the last WE will initiate the execution of the Sector Erase command(s). If another falling edge of the WE occurs within the 50 s time-out window the timer is reset. Monitor DQ3 to determine if the sector erase timer window is still open. (See section DQ3, Sector Erase Timer.) Any command other than Sector Erase or Erase Suspend during this time-out period will reset the device to the read mode, ignoring the previous command string. Resetting the device once excution has begun will corrupt the data in the sector. In that case, restart the erase on those sectors and allow them to complete. (Refer to the Write Operation Status section for Sector Erase Timer operation.) Loading the sector erase buffer may be done in any sequence and with any number of sectors (0 to 34). Sector erase does not require the user to program the device prior to erase. The device automatically programs all memory locations in the sector(s) to be erased prior to electrical erase (Preprogram Function). When erasing a sector or sectors the remaining unselected sectors are not affected. The system is not required to provide any controls or timings during these operations. (See Figure 8.) The automatic sector erase begins after the 50 s time out from the rising edge of the WE pulse for the last sector erase command pulse and terminates when the data on DQ7 is "1" (See Write Operation Status section) at which time the device returns to the read mode. Data polling must be performed at an address within any of the sectors being erased. Multiple Sector Erase Time; [Sector Program Time (Preprogramming) + Sector Erase Time] x Number of Sector Erase. Figure 21 illustrates the Embedded EraseTM Algorithm using typical command strings and bus operations. Erase Suspend/Resume The Erase Suspend command allows the user to interrupt a Sector Erase operation and then perform data reads from or program to a sector not being erased. This command is applicable ONLY during the Sector Erase operation which includes the time-out period for sector erase. The Erase Suspend command will be ignored if written during the Chip Erase operation or Embedded Program Algorithm. Writting the Erase Suspend command during the Sector Erase time-out results in immediate termination of the time-out period and suspension of the erase operation. Writing the Erase Resume command resumes the erase operation. The addresses are "DON'T CARES" when writing the Erase Suspend or Erase Resume commands. When the Erase Suspend command is written during the Sector Erase operation, the device will take a maximum of 20 s to suspend the erase operation. When the devices have entered the erase-suspended mode, the RY/ BY output pin and the DQ7 bit will be at logic "1", and DQ6 will stop toggling. The user must use the address of the erasing sector for reading DQ6 and DQ7 to determine if the erase operation has been suspended. Further writes of the Erase Suspend command are ignored. When the erase operation has been suspended, the device defaults to the erase-suspend-read mode. Reading data in this mode is the same as reading from the standard read mode except that the data must be read from sectors that have not been erase-suspended. Successively reading from the erase-suspended sector while the device is in the erase-suspend-read mode will cause DQ2 to toggle. (See the section on DQ2.) After entering the erase-suspend-read mode, the user can program the device by writing the appropriate command sequence for Program. This Program mode is known as the erase-suspend-program mode. Again, programming in this mode is the same as programming in the regular Program mode except that the data must 20 MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 be programmed to sectors that are not erase-suspended. Successively reading from the erase-suspended sector while the devices are in the erase-suspend-program mode will cause DQ2 to toggle. The end of the erasesuspended Program operation is detected by the RY/BY output pin, Data polling of DQ7, or the Toggle Bit (DQ6) which is the same as the regular Program operation. Note that DQ7 must be read from the Program address while DQ6 can be read from any address. To resume the operation of Sector Erase, the Resume command (30H) should be written. Any further writes of the Resume command at this point will be ignored. Another Erase Suspend command can be written after the chip has resumed erasing. Extended Command (1) Fast Mode MBM29LV160T/B has Fast Mode function. This mode dispenses with the initial two unlock cycles required in the standard program command sequence writing Fast Mode command into the command register. In this mode, the required bus cycle for programming is two cycles instead of four bus cycles in standard program command. (Do not write erase command in this mode.) The read operation is also executed after exiting this mode. To exit this mode, it is necessary to write Fast Mode Reset command into the command register. (Refer to the Figure 26 Extended algorithm.) The VCC active current is required even CE = VIH during Fast Mode. (2) Fast Programming During Fast Mode, the programming can be executed with two bus cycles operation. The Embedded Program Algorithm is executed by writing program set-up command (A0H) and data write cycles (PA/PD). (Refer to the Figure 26 Extended algorithm.) (3) CFI (Common Flash Memory Interface) The CFI (Common Flash Memory Interface) specification outlines device and host system software interrogation handshake which allows specific vendor-specified software algorithms to be used for entire families of devices. This allows device-independent, JEDEC ID-independent, and forward-and backwardcompatible software support for the specified flash device families. Refer to CFI specification in detail. The operation is initiated by writing the query command (98H) into the command register. Following the command write, a read cycle from specific address retrives device information. Please note that output data of upper byte (DQ8 to DQ15) is "0" in word mode (16 bit) read. Refer to the CFI code table. To terminate operation, it is necessary to write the read/reset command sequence into the register. (4) Extended Sector Protect In addition to normal sector protection, the MBM29LV160T/B has Extended Sector Protection as extended function. This function enable to protect sector by forcing VID on RESET pin and write a commnad sequence. Unlike conventional procedure, it is not necessary to force VID and control timing for control pins. The only RESET pin requires VID for sector protection in this mode. The extended sector protect requires VID on RESET pin. With this condition, the operation is initiated by writing the set-up command (60H) into the command register. Then, the sector addresses pins (A19, A18, A17, A16, A15, A14, A13 and A12) and (A6, A1, A0) = (0, 1, 0) should be set to the sector to be protected (recommend to set VIL for the other addresses pins), and write extended sector protect command (60H). A sector is typically protected in 150 s. To verify programming of the protection circuitry, the sector addresses pins (A19, A18, A17, A16, A15, A14, A13 and A12) and (A6, A1, A0) = (0, 1, 0) should be set and write a command (40H). Following the command write, a logical "1" at device output DQ0 will produce for protected sector in the read operation. If the output data is logical "0", please repeat to write extended sector protect command (60H) again. To terminate the operation, it is necessary to set RESET pin to VIH. 21 MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 Write Operation Status Table 9 Status Embedded Program Algorithm Embedded/Erase Algorithm In Progress Erase Suspend Read (Erase Suspended Sector) Erase Erase Suspend Read Suspend (Non-Erase Suspended Sector) Mode Erase Suspend Program (Non-Erase Suspended Sector) Embedded Program Algorithm Exceeded Time Limits Embedded/Erase Algorithm Erase Suspend Program (Non-Erase Suspended Sector) Hardware Sequence Flags DQ7 DQ7 0 1 Data DQ7 DQ7 0 DQ7 DQ6 Toggle Toggle 1 Data Toggle (Note 1) Toggle Toggle Toggle DQ5 0 0 0 Data 0 1 1 1 DQ3 0 1 0 Data 0 0 1 0 DQ2 1 Toggle Toggle Data 1 (Note 2) 1 N/A N/A Notes: 1. Performing successive read operations from any address will cause DQ6 to toggle. 2. Reading the byte address being programmed while in the erase-suspend program mode will indicate logic "1" at the DQ2 bit. However, successive reads from the erase-suspended sector will cause DQ2 to toggle. 3. DQ0 and DQ1 are reserve pins for future use. 4. DQ4 is Fujitsu internal use only. DQ7 Data Polling The MBM29LV160T/B device features Data Polling as a method to indicate to the host that the Embedded Algorithms are in progress or completed. During the Embedded Program Algorithm, an attempt to read the devices will produce the complement of the data last written to DQ7. Upon completion of the Embedded Program Algorithm, an attempt to read the device will produce the true data last written to DQ7. During the Embedded Erase Algorithm, an attempt to read the device will produce a "0" at the DQ7 output. Upon completion of the Embedded Erase Algorithm an attempt to read the device will produce a "1" at the DQ7 output. The flowchart for Data Polling (DQ7) is shown in Figure 22. For chip erase and sector erase, Data Polling is valid after the rising edge of the sixth WE pulse in the six-write pulse sequence. Data Polling must be performed at a sector address within any of the sectors being erased and not at a protected sector. Otherwise, the status may not be valid. Once the Embedded Algorithm operation is close to being completed, the MBM29LV160T/B data pins (DQ7) may change asynchronously while the output enable (OE) is asserted low. This means that the device is driving status information on DQ7 at one instant of time and then that byte's valid data at the next instant of time. Depending on when the system samples the DQ7 output, it may read the status or valid data. Even if the device has completed the Embedded Program Algorithm operation and DQ7 has a valid data, the data outputs on DQ0 to DQ6 may be still invalid. The valid data on DQ0 to DQ7 will be read on successive read attempts. The Data Polling feature is only active during the Embedded Programming Algorithm, Embedded Erase Algorithm or sector erase time-out. See Figure 9 for the Data Polling timing specifications and diagrams. 22 MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 DQ6 Toggle Bit I The MBM29LV160T/B also feature the "Toggle Bit I" as a method to indicate to the host system that the Embedded Algorithms are in progress or completed. During an Embedded Program or Erase Algorithm cycle, successive attempts to read (OE toggling) data from the device will result in DQ6 toggling between one and zero. Once the Embedded Program or Erase Algorithm cycle is completed, DQ6 will stop toggling and valid data can be read on the next successive attempts. During programming, the Toggle Bit I is valid after the rising edge of the fourth WE pulse in the four write pulse sequence. For chip erase and sector erase, the Toggle Bit I is valid after the rising edge of the sixth WE pulse in the sixwrite pulse sequence. The Toggle Bit I is active during the sector time out. In programming, if the sector being written to is protected, the toggle bit will toggle for about 2 s and then stop toggling without the data having changed. In erase, the device will erase all the selected sectors except for the ones that are protected. If all selected sectors are protected, the chip will toggle the Toggle Bit I for about 200 s and then drop back into read mode, having changed none of the data. Either CE or OE toggling will cause the DQ6 to toggle. In addition, an Erase Suspend/Resume command will cause the DQ6 to toggle. See Figure 10 and Figure 23 for the Toggle Bit I timing specifications and diagrams. DQ5 Exceeded Timing Limits DQ5 will indicate if the program or erase time has exceeded the specified limits (internal pulse count). Under these conditions DQ5 will produce a "1". This is a failure condition which indicates that the program or erase cycle was not successfully completed. Data Polling is the only operating function of the device under this condition. The CE circuit will partially power down the device under these conditions. The OE and WE pins will control the output disable functions as described in Tables 2 and 3. The DQ5 failure condition may also appear if a user tries to program a non blank location without erasing. In this case the device locks out and never completes the Embedded Algorithm operation. Hence, the system never reads a valid data on DQ7 and DQ6 never stops toggling. Once the device has exceeded timing limits, the DQ5 bit will indicate a "1." Please note that this is not a device failure condition since the device was incorrectly used. If this occurs, reset the device with command sequence. DQ3 Sector Erase Timer After the completion of the initial sector erase command sequence the sector erase time-out will begin. DQ3 will remain low until the time-out is complete. Data Polling and Toggle Bit I are valid after the initial sector erase command sequence. If Data Polling or the Toggle Bit I indicates the device has been written with a valid erase command, DQ3 may be used to determine if the sector erase timer window is still open. If DQ3 is high ("1") the internally controlled erase cycle has begun; attempts to write subsequent commands to the device will be ignored until the erase operation is completed as indicated by Data Polling or Toggle Bit I. If DQ3 is low ("0"), the device will accept additional sector erase commands. To insure the command has been accepted, the system software should check the status of DQ3 prior to and following each subsequent sector erase command. If DQ3 is high on the second status check, the command may not have been accepted. See Table 9: Hardware Sequence Flags. 23 MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 DQ2 Toggle Bit II This Toggle Bit II, along with DQ6, can be used to determine whether the device is in the Embedded Erase Algorithm or in Erase Suspend. Successive reads from the erasing sector will cause DQ2 to toggle during the Embedded Erase Algorithm. If the device is in the erase-suspended-read mode, successive reads from the erase-suspended sector will cause DQ2 to toggle. When the device is in the erase-suspended-program mode, successive reads from the byte address of the non-erase suspended sector will indicate a logic "1" at DQ2. DQ6 is different from DQ2 in that DQ6 toggles only when the standard program or Erase, or Erase Suspend Program operation is in progress. For example, DQ2 and DQ6 can be used together to determine if the erase-suspend-read mode is in progress. (DQ2 toggles while DQ6 does not.) See also Table 10 and Figure 19. Furthermore, DQ2 can also be used to determine which sector is being erased. When the device is in the erase mode, DQ2 toggles if this bit is read from an erasing sector. Table 10 Mode Program Erase Erase Suspend Read (Erase Suspended Sector) (Note 1) Erase-Suspend Program DQ7 DQ7 0 1 DQ7 Toggle Bit Status DQ6 Toggle Toggle 1 Toggle (Note 1) DQ2 1 Toggle Toggle 1 (Note 2) Notes: 1. Performing successive read operations from any address will cause DQ6 to toggle. 2. Reading the byte address being programmed while in the erase-suspend program mode will indicate logic "1" at the DQ2 bit. However, successive reads from the erase-suspended sector will cause DQ2 to toggle. RY/BY Ready/Busy Pin The MBM29LV160T/B provides a RY/BY open-drain output pin as a way to indicate to the host system that the Embedded Algorithms are either in progress or has been completed. If the output is low, the device is busy with either a program or erase operation. If the output is high, the device is ready to accept any read/write or erase operation. When the RY/BY pin is low, the devices will not accept any additional program or erase commands with the exception of the Erase Suspend command. If the MBM29LV160T/B is placed in an Erase Suspend mode, the RY/BY output will be high, by means of connecting with a pull-up resister to VCC. During programming, the RY/BY pin is driven low after the rising edge of the fourth WE pulse. During an erase operation, the RY/BY pin is driven low after the rising edge of the sixth WE pulse. The RY/BY pin will indicate a busy condition during the RESET pulse. See Figure 11 and 12 for a detailed timing diagram. The RY/BY pin is pulled high in standby mode. Since this is an open-drain output, RY/BY pins can be tied together in parallel with a pull-up resistor to VCC. 24 MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 RESET Hardware Reset Pin The MBM29LV160T/B device may be reset by driving the RESET pin to VIL. The RESET pin has a pulse requirement and has to be kept low (VIL) for at least 500 ns in order to properly reset the internal state machine. Any operation in the process of being executed will be terminated and the internal state machine will be reset to the read mode tREADY after the RESET pin is driven low. Furthermore, once the RESET pin goes high, the device requires an additional tRH before it allows read access. When the RESET pin is low, the device will be in the standby mode for the duration of the pulse and all the data output pins will be tri-stated. If a hardware reset occurs during a program or erase operation, the data at that particular location will be corrupted. Please note that the RY/BY output signal should be ignored during the RESET pulse. Refer to Figure 12 for the timing diagram. Refer to Temporary Sector Unprotection for additional functionality. If hardware reset occurs during Embedded Erase Algorithm, there is a possibility that the erasing sector(s) will need to be erased again before they can be programmed. Word/Byte Configuration The BYTE pin selects the byte (8-bit) mode or word (16-bit) mode for the MBM29LV160T/B device. When this pin is driven high, the device operates in the word (16-bit) mode. The data is read and programmed at DQ0 to DQ15. When this pin is driven low, the device operates in byte (8-bit) mode. Under this mode, DQ15/A-1 pin becomes the lowest address bit and DQ8 to DQ14 bits are tri-stated. However, the command bus cycle is always an 8-bit operation and hence commands are written at DQ0 to DQ7 and DQ8 to DQ15 bits are ignored. Refer to Figures 13 and 14 for the timing diagrams. Data Protection The MBM29LV160T/B is designed to offer protection against accidental erasure or programming caused by spurious system level signals that may exist during power transitions. During power up the device automatically resets the internal state machine to the Read mode. Also, with its control register architecture, alteration of the memory contents only occurs after successful completion of specific multi-bus cycle command sequence. The device also incorporates several features to prevent inadvertent write cycles resulting form VCC power-up and power-down transitions or system noise. Low VCC Write Inhibit To avoid initiation of a write cycle during VCC power-up and power-down, a write cycle is locked out for VCC less than 2.3 V (typically 2.4 V). If VCC < VLKO, the command register is disabled and all internal program/erase circuits are disabled. Under this condition, the device will reset to the read mode. Subsequent writes will be ignored until the VCC level is greater than VLKO. It is the users responsibility to ensure that the control pins are logically correct to prevent unintentional writes when VCC is above 2.3 V. If the Embedded Erase Algorithm is interrupted, there is possibility that the erasing sector(s) will need to be erased again prior to programming. Write Pulse "Glitch" Protection Noise pulses of less than 5 ns (typical) on OE, CE, or WE will not change the command registers. Logical Inhibit Writing is inhibited by holding any one of OE = VIL, CE = VIH, or WE = VIH. To initiate a write, CE and WE must be a logical zero while OE is a logical one. Power-up Write Inhibit Power-up of the devices with WE = CE = VIL and OE = VIH will not accept commands on the rising edge of WE. The internal state machine is automatically reset to read mode on power-up. Handling of SON Package The metal portion of marking side is connected with internal chip electrically. Please pay attention not to occur electrical connection during operation. In worst case, it may be caused permanent damage to device or system by excessive current. 25 MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 Table 11 Common Flash Memory Interface Code Description Query-unique ASCII string "QRY" Primary OEM Command Set 2h: AMD/FJ standard type Address for Primary Extended Table Alternate OEM Command Set (00h = not applicable) Address for Alternate OEM Extended Table VCC Min. (write/erase) D7-4: volt, D3-0: 100 mvolt VCC Max. (write/erase) D7-4: volt, D3-0: 100 mvolt VPP Min. voltage VPP Max. voltage Typical timeout per single byte/word write 2N s Typical timeout for Min. size buffer write 2N s Typical timeout per individual block erase 2N ms Typical timeout for full chip erase 2N ms Max. timeout for byte/word write 2N times typical Max. timeout for buffer write 2N times typical Max. timeout per individual block erase 2N times typical Max. timeout for full chip erase 2N times typical Device Size = 2N byte Flash Device Interface description Max. number of byte in multi-byte write = 2N Number of Erase Block Regions within device A0 to A6 10h 11h 12h 13h 14h 15h 16h 17h 18h 19h 1Ah 1Bh 1Ch 1Dh 1Eh 1Fh 20h 21h 22h 23h 24h 25h 26h 27h 28h 29h 2Ah 2Bh 2Ch DQ0 to DQ15 Description Erase Block Region 1 Information A0 to A6 2Dh 2Eh 2Fh 30h 31h 32h 33h 34h 35h 36h 37h 38h 39h 3Ah 3Bh 3Ch 40h 41h 42h 43h 44h 45h DQ0 to DQ15 0051h 0052h 0059h 0002h 0000h 0040h 0000h 0000h 0000h 0000h 0000h 0027h 0036h 0000h 0000h 0004h 0000h 0000h 0040h 0000h 0001h 0000h 0020h 0000h 0000h 0000h 0080h 0000h 001Eh 0000h 0000h 0001h 0050h 0052h 0049h 0031h 0030h 0000h Erase Block Region 2 Information Erase Block Region 3 Information Erase Block Region 4 Information Query-unique ASCII string "PRI" Major version number, ASCII 0000h 000Ah 0000h 0005h 0000h 0004h 0000h 0015h 0002h 0000h 0000h 0000h 0004h Minor version number, ASCII Address Sensitive Unlock 0 = Required 1 = Not Required Erase Suspend 0 = Not Supported 1 = To Read Only 2 = To Read & Write Sector Protect 0 = Not Supported X = Number of sectors in per group Sector Temporary Unprotect 00 = Not Supported 01 = Supported Reserve 46h 0002h 47h 0001h 48h 0001h 49h 4Ah 4Bh 4Ch XXXXh XXXXh XXXXh XXXXh 26 MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 s ABSOLUTE MAXIMUM RATINGS Storage Temperature .................................................................................................. -55C to +125C Ambient Temperature with Power Applied .................................................................. -40C to +85C Voltage with respect to Ground All pins except A9, OE, and RESET (Note 1) ............ -0.5 V to +VCC +0.5 V VCC (Note 1) ................................................................................................................ -0.5 V to +5.5 V A9, OE, and RESET (Note 2) ...................................................................................... -0.5 V to +13.0 V Notes: 1. Minimum DC voltage on input or l/O pins are -0.5 V. During voltage transitions, inputs may negative overshoot VSS to -2.0 V for periods of up to 20 ns. Maximum DC voltage on output and l/O pins are VCC +0.5 V. During voltage transitions,outputs may positive overshoot to VCC +2.0 V for periods of up to 20 ns. 2. Minimum DC input voltage on A9, OE, and RESET pins are -0.5 V. During voltage transitions, A9, OE, and RESET pins may negative overshoot VSS to -2.0 V for periods of up to 20 ns. Maximum DC input voltage on A9, OE, and RESET pins are +13.0 V which may positive overshoot to 14.0 V for periods of up to 20 ns. Voltage difference between input voltage and supply voltage (VIN - VCC) do not exceed 9 V. WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current, temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings. s RECOMMENDED OPERATING RANGES Ambient Temperature (TA) MBM29LV160T/B-80 .................................................................................-20C to +70C MBM29LV160T/B-90/-12...........................................................................-40C to +85C VCC Supply Voltages MBM29LV160T/B-80 .................................................................................+3.0 V to +3.6 V MBM29LV160T/B-90/-12...........................................................................+2.7 V to +3.6 V Operating ranges define those limits between which the functionality of the device is quaranteed. WARNING: The recommended operating conditions are required in order to ensure the normal operation of the semiconductor device. All the device's electrical characteristics are warranted when the device is operated within these ranges. Always use semiconductor devices within their recommended operating condition ranges. Operation outside these ranges may adversely affect reliability and could result in device failure. No warranty is made with respect to uses, operating conditions, or combinations not represented on the data sheet. Users considering application outside the listed conditions are advised to contact their FUJITSU representatives beforehand. 27 MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 s MAXIMUM OVERSHOOT +0.6 V -0.5 V -2.0 V 20 ns 20 ns 20 ns Figure 1 Maximum Negative Overshoot Waveform 20 ns VCC +2.0 V VCC +0.5 V +2.0 V 20 ns 20 ns Figure 2 Maximum Positive Overshoot Waveform 1 20 ns +14.0 V +13.0 V VCC +0.5 V 20 ns 20 ns Note : This waveform is applied for A9, OE, and RESET. Figure 3 Maximum Positive Overshoot Waveform 2 28 MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 s DC CHARACTERISTICS Parameter Symbol ILI ILO ILIT Parameter Description Input Leakage Current Output Leakage Current A9, OE, RESET Inputs Leakage Current Test Conditions VIN = VSS to VCC, VCC = VCC Max. VOUT = VSS to VCC, VCC = VCC Max. VCC = VCC Max., A9, OE, RESET = 12.5 V CE = VIL, OE = VIH f = 10 MHz ICC1 VCC Active Current (Note 1) CE = VIL, OE = VIH f = 5 MHz ICC2 ICC3 ICC4 VCC Active Current (Note 2) VCC Current (Standby) VCC Current (Standby, RESET) CE = VIL, OE = VIH VCC = VCC Max., CE = VCC 0.3 V, RESET = VCC 0.3 V VCC = VCC Max., RESET = VSS 0.3 V Byte -- Word -- -- -- 17 35 5 5 mA A A 15 mA Byte -- Word 35 Min. -1.0 -1.0 -- Max. +1.0 +1.0 35 30 mA Unit A A A ICC5 VIL VIH VCC = VCC Max., CE = VSS 0.3 V, VCC Current RESET = VCC 0.3 V, (Automatic Sleep Mode) (Note 3) VIN = VCC 0.3 V or VSS 0.3 V Input Low Level Input High Level Voltage for Autoselect,Sector Protection, and Temporary Sector Unprotection (A9, OE, RESET) (Note 4) Output Low Voltage Level Output High Voltage Level -- -- -- -0.5 2.0 5 0.6 VCC + 0.3 A V V VID -- 11.5 12.5 V VOL VOH1 VOH2 VLKO Notes: 1. 2. 3. 4. IOL = 4.0 mA, VCC = VCC Min. IOH = -2.0 mA, VCC = VCC Min. IOH = -100 A -- 2.4 VCC - 0.4 0.45 -- -- 2.5 V V V V Low VCC Lock-Out Voltage -- 2.3 The lCC current listed includes both the DC operating current and the frequency dependent component. lCC active while Embedded Erase or Embedded Program is in progress. Automatic sleep mode enables the low power mode when address remain stable for 150 ns. (VID - VCC) do not exceed 9 V. 29 MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 s AC CHARACTERISTICS * Read Only Operations Characteristics Parameter Symbols JEDEC tAVAV tAVQV tELQV tGLQV tEHQZ tGHQZ tAXQX -- -- Standard tRC tACC tCE tOE tDF tDF tOH tREADY tELFL tELFH Read Cycle Time Address to Output Delay Chip Enable to Output Delay Output Enable to Output Delay Chip Enable to Output HIGH-Z Output Enable to Output HIGH-Z Output Hold Time From Address, CE or OE, Whichever Occurs First RESET Pin Low to Read Mode CE or BYTE Switching Low or High -- CE = VIL OE = VIL OE = VIL -- -- -- -- -- -- Min. Max. Max. Max. Max. Max. Min. Max. Max. 80 80 80 30 25 25 0 20 5 90 90 90 35 30 30 0 20 5 120 120 120 50 30 30 0 20 5 ns ns ns ns ns ns ns s ns -80 (Note) -90 (Note) -12 (Note) Description Test Setup Unit Note: Test Conditions: Output Load: 1 TTL gate and 30 pF (MBM29LV160T/B-80/-90) 1 TTL gate and 100 pF (MBM29LV160T/B-12) Input rise and fall times: 5 ns Input pulse levels: 0.0 V to 3.0 V Timing measurement reference level Input: 1.5 V Output: 1.5 V 3.3 V IN3064 or Equivalent Device Under Test 6.2 k CL Diodes = IN3064 or Equivalent 2.7 k Notes: CL = 30 pF including jig capacitance (MBM29LV160T/B-80/-90) CL = 100 pF including jig capacitance (MBM29LV160T/B-12) Figure 4 Test Conditions 30 MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 * Write (Erase/Program) Operations Parameter Symbols Description JEDEC tAVAV tAVWL tWLAX tDVWH tWHDX -- -- tGHWL tGHEL tELWL tWLEL tWHEH tEHWH tWLWH tELEH tWHWL tEHEL tWHWH1 tWHWH2 -- -- -- -- -- -- -- Standard tWC tAS tAH tDS tDH tOES tOEH tGHWL tGHEL tCS tWS tCH tWH tWP tCP tWPH tCPH tWHWH1 tWHWH2 tEOE tVCS tVLHT tWPP tOESP tCSP tRB Write Cycle Time Address Setup Time Address Hold Time Data Setup Time Data Hold Time Output Enable Setup Time Output Enable Read Hold Time Toggle and Data Polling Read Recover Time Before Write Read Recover Time Before Write (OE High to CE Low) CE Setup Time WE Setup Time CE Hold Time WE Hold Time Write Pulse Width CE Pulse Width Write Pulse Width High CE Pulse Width High Byte Programming Operation Word Sector Erase Operation (Note 1) Delay Time from Embedded Output Enable VCC Setup Time Voltage Transition Time (Note 2) Write Pulse Width (Note 2) OE Setup Time to WE Active (Note 2) CE Setup Time to WE Active (Note 2) Recover Time From RY/BY Typ. Max. Min. Min. Min. Min. Min. Min. Typ. 16 1 30 50 4 100 4 4 0 16 1 35 50 4 100 4 4 0 16 1 50 50 4 100 4 4 0 sec ns s s s s s ns Min. Min. Min. Min. Min. Min. Min. Min. Min. Min. Min. Min. Min. Min. Min. Min. Min. Min. -80 80 0 45 35 0 0 0 10 0 0 0 0 0 0 35 35 25 25 8 -90 90 0 45 45 0 0 0 10 0 0 0 0 0 0 45 45 25 25 8 -12 120 0 50 50 0 0 0 10 0 0 0 0 0 0 50 50 30 30 8 s ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns MBM29LV160T/B Unit (Continued) 31 MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 (Continued) Parameter Symbols Description JEDEC -- -- -- -- -- -- Standard tRH tBUSY tFLQZ tFHQV tVIDR tRP RESET Hold Time Before Read Program/Erase Valid to RY/BY Delay BYTE Switching Low to Output HIGH-Z BYTE Switching High to Output Active Rise Time to VID (Note 2) RESET Pulse Width Min. Max. Max. Min. Min. Min. -80 200 90 30 30 500 500 -90 200 90 35 35 500 500 -12 200 90 50 50 500 500 ns ns ns ns ns ns MBM29LV160T/B Unit Notes: 1. This does not include the preprogramming time. 2. This timing is for Sector Protection operation. 32 MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 s SWITCHING WAVEFORMS * Key to Switching Waveforms WAVEFORM INPUTS Must Be Steady May Change from H to L May Change from L to H "H" or "L": Any Change Permitted Does Not Apply OUTPUTS Will Be Steady Will Be Change from H to L Will Be Change from L to H Changing, State Unknown Center Line is HighImpedance "Off" State tRC Addresses Addresses Stable tACC CE tOE tDF OE tOEH WE tCE tOH Outputs HIGH-Z Output Valid HIGH-Z Figure 5.1 AC Waveforms for Read Operations 33 MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 tRC Addresses tACC tRH Addresses Stable RESET tOH Outputs HIGH-Z Output Valid Figure 5.2 AC Waveforms for Hardware Reset/Read Operations 34 MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 3rd Bus Cycle Addresses 555H tWC tAS PA tAH Data Polling PA tRC CE tCS tCH tCE OE tGHWL tWP tWPH tWHWH1 tOE WE tDS tDH tDF tOH Data A0H PD DQ7 DOUT DOUT Notes: 1. 2. 3. 4. 5. 6. PA is address of the memory location to be programmed. PD is data to be programmed at word address. DQ7 is the output of the complement of the data written to the device. DOUT is the output of the data written to the device. Figure indicates last two bus cycles out of four bus cycle sequence. These waveforms are for the x16 mode. (The addresses differ from x8 mode.) Figure 6 AC Waveforms for Alternate WE Controlled Program Operations 35 MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 3rd Bus Cycle Data Polling PA tAS tAH PA Addresses 555H tWC WE tWS tWH OE tGHEL tCP tCPH tWHWH1 CE tDS tDH PD DQ7 DOUT Data A0H Notes: 1. 2. 3. 4. 5. 6. PA is address of the memory location to be programmed. PD is data to be programmed at word address. DQ7 is the output of the complement of the data written to the device. DOUT is the output of the data written to the device. Figure indicates last two bus cycles out of four bus cycle sequence. These waveforms are for the x16 mode. (The addresses differ from x8 mode.) Figure 7 AC Waveforms for Alternate CE Controlled Program Operations 36 MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 Addresses 555H tWC 2AAH tAS tAH 555H 555H 2AAH SA* CE tCS tCH OE tGHWL tWP tWPH WE tDS AAH tDH 55H 80H AAH 55H 30H for Sector Erase 10H Data tVCS VCC * : 1. SA is the sector address for Sector Erase. Addresses = 555H (Word), AAAAH (Byte) for Chip Erase. 2. These waveforms are for the x16 mode. (The addresses differ from x8 mode.) Figure 8 AC Waveforms for Chip/Sector Erase Operations 37 MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 CE tCH tOE tDF OE tOEH WE tCE * DQ7 Data DQ7 DQ7 = Valid Data High-Z tWHWH1 or 2 High-Z DQ0 to DQ6 Data DQ0 to DQ6 = Output Flag DQ0 to DQ6 Valid Data (tEOE) * : DQ7 = Valid Data (The device has completed the Embedded operation.) Figure 9 AC Waveforms for Data Polling during Embedded Algorithm Operations CE tOEH WE tOES OE * DQ6 = Toggle DQ6 = Stop Toggling tOE DQ0 to DQ7 Data Valid tDH DQ6 Data DQ6 = Toggle * : DQ6 = Stops toggling. (The device has completed the Embedded operation.) Figure 10 AC Waveforms for Taggle Bit I during Embedded Algorithm Operations 38 MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 CE The rising edge of the last WE signal WE Entire programming or erase operations RY/BY tBUSY Figure 11 RY/BY Timing Diagram during Program/Erase Operations WE RESET tRP tRB RY/BY tREADY Figure 12 RESET, RY/BY Timing Diagram 39 MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 CE OE BYTE DQ0 to DQ14 tELFH DQ0 to DQ7 tFHQV A-1 DQ0 to DQ14 DQ15/A-1 DQ15 Figure 13 Timing Diagram for Word Mode Configuration CE OE BYTE tELFL DQ0 to DQ14 DQ0 to DQ7 DQ0 to DQ14 DQ15/A-1 DQ15 tFLQZ A-1 Figure 14 Timing Diagram for Byte Mode Configuration 40 MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 CE The falling edge of the last WE signal WE BYTE tSET (tAS) Input Valid tHOLD (tAH) Figure 15 BYTE Timing Diagram for Write Operations 41 MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 A19, A18, A17 A16, A15, A14 A13, A12 SAX SAY A0 A1 A6 12 V 3V A9 12 V 3V OE tVLHT tWPP tVLHT tVLHT WE tOESP tCSP tVLHT CE Data tVCS tOE 01H VCC SAX = Sector Address for initial sector SAY = Sector Address for next sector Note: A-1 is VIL on byte mode. Figure 16 AC Waveforms for Sector Protection Timing Diagram 42 MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 VCC tVCS RESET tVIDR tVLHT Add SPAX SPAX SPAY A0 A1 A6 CE OE WE 60H 60H 40H tOE 01H 60H TIME-OUT Data SPAX : Sector Address to be protected SPAY : Next Sector Address to be protected TIME-OUT : Time-out Window = 150 s (min) Figure 17 Extended Sector Protection Timing Diagram 43 MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 VCC tVCS VID 3V RESET CE tVIDR tVLHT 3V WE tVLHT RY/BY Program or Erase Command Sequence tVLHT Unprotection period Figure 18 Temporary Sector Unprotection Timing Diagram Enter Embedded Erasing WE Erase Suspend Erase Enter Erase Suspend Program Erase Suspend Program Erase Resume Erase Suspend Read Erase Erase Complete Erase Suspend Read DQ6 DQ2 Toggle DQ2 and DQ6 with OE Note: DQ2 is read from the erase-suspended sector. Figure 19 DQ2 vs. DQ6 44 MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 EMBEDDED PROGRAM TM ALGORITHM Start Write Program Command Sequence (See Below) Data Polling Device No Verify Byte ? Yes No Increment Address Last Address ? Yes Programming Completed Program Command Sequence* (Address/Command): 555H/AAH 2AAH/55H 555H/A0H Program Address/Program Data * : The sequence is applied for x16 mode. The addresses differ from x8 mode. Figure 20 Embedded ProgramTM Algorithm 45 MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 EMBEDDED PROGRAM TM ALGORITHM Start Write Erase Command Sequece (See Below) Data Polling or Toggle Bit from Device No Data = FFH ? Yes Erasure Completed Chip Erase Command Sequence* (Address/Command): 555H/AAH Individual Sector/Multiple Sector* Erase Command Sequence (Address/Command): 555H/AAH 2AAH/55H 2AAH/55H 555H/80H 555H/80H 555H/AAH 555H/AAH 2AAH/55H 2AAH/55H 555H/10H Sector Address/30H Sector Address/30H Additional sector erase commands are optional. Sector Address/30H * : The sequence is applied for x16 mode. The addresses differ from x8 mode. Figure 21 Embedded EraseTM Algorithm 46 MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 Start Read Byte (DQ0 to DQ7) Addr. = VA DQ7 = Data? No No DQ5 = 1? Yes Read Byte (DQ0 to DQ7) Addr. = VA Yes VA =Address for programming =Any of the sector addresses within the sector being erased during sector erase or multiple erases operation. =Any of the sector addresses within the sector not being protected during sector erase or multiple sector erases operation. DQ7 = Data? * No Fail Yes Pass * : DQ7 is rechecked even if DQ5 = "1" because DQ7 may change simultaneously with DQ5. Figure 22 Data Polling Algorithm 47 MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 Start Read (DQ0 to DQ7) Addr. = "H" or "L" No DQ6 = Toggle ? Yes No DQ5 = 1? Yes Read Byte (DQ0 to DQ7) Addr. = "H" or "L" DQ6 = Toggle ?* Yes Fail No Pass * : DQ6 is rechecked even if DQ5 = "1" because DQ6 may stop toggling at the same time as DQ5 changing to "1". Figure 23 Toggle Bit Algorithm 48 MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 Start Setup Sector Addr. (A19, A18, A17, A16, A15, A14, A13, A12) PLSCNT = 1 OE = VID, A9 = VID A6 = CE = VIL, RESET = VIH A0 = VIL, A1 = VIH Activate WE Pulse Increment PLSCNT Time out 100 s WE = VIH, CE = OE = VIL (A9 should remain VID) Read from Sector ( A1 = VIH, A0 = VIL, Addr. = SA, A6 = VIL)* No No PLSCNT = 25? Yes Remove VID from A9 Write Reset Command Data = 01H? Yes Protect Another Sector? No Device Failed Remove VID from A9 Write Reset Command Sector Protection Completed * : A-1 is VIL on byte mode. Figure 24 Sector Protection Algorithm 49 MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 Start RESET = VID (Note 1) Perform Erase or Program Operations RESET = VIH Temporary Sector Unprotection Completed (Note 2) Notes: 1. All protected sectors are unprotected. 2. All previously protected sectors are protected once again. Figure 25 Temporary Sector Unprotection Algorithm 50 MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 FAST MODE ALGORITHM Start 555H/AAH 2AAH/55H Set Fast Mode 555H/20H XXXXH/A0H Program Address/Program Data In Fast Program Data Polling Device Verify Byte? Yes No Increment Address Last Address ? Yes Programming Completed No XXXXH/90H Reset Fast Mode XXXXH/F0H * : The sequence is applied for x16 mode. * : The addresses differ from x8 mode. Figure 26 Embedded Programming Algorithm for Fast Mode 51 MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 FAST MODE ALGORITHM Start RESET = VID Wait to 4 s Device is Operating in Temporary Sector Unprotect Mode No Extended Sector Protect Entry? Yes To Setup Sector Protect Write XXXH/60H PLSCNT = 1 To Sector Protect Write 60H to Sector Address (A0 = VIL, A1 = VIH, A6 = VIL) Time out 150 s Increment PLSCNT To Verify Sector Protect Write 40H to Sector Address (A0 = VIL, A1 = VIH, A6 = VIL) No Read from Sector Address (A0 = VIL, A1 = VIH, A6 = VIL) Setup Next Sector Address No PLSCNT = 25? Yes Remove VID from RESET Write Reset Command Data = 01H? Yes Yes Protect Other Sector ? No Remove VID from RESET Write Reset Command Device Failed Sector Protection Completed Figure 27 Extended Sector Protect Algorithm 52 MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 s ERASE AND PROGRAMMING PERFORMANCE Limits Parameter Min. Sector Erase Time Byte Programming Time Word Programming Time Chip Programming Time Erase/Program Cycle -- -- -- -- 100,000 Typ. 1 8 16 16.8 -- Max. 10 300 s 360 50 -- sec cycles sec Excludes programming time prior to erasure Excludes system-level overhead Excludes system-level overhead -- Unit Comments s TSOP (I) PIN CAPACITANCE Parameter Symbol CIN COUT CIN2 Parameter Description Input Capacitance Output Capacitance Control Pin Capacitance Test Setup VIN = 0 VOUT = 0 VIN = 0 Typ. 7.5 8 10 Max. 9.5 10 13 Unit pF pF pF Note: Test conditions TA = 25C, f = 1.0 MHz s SON PIN CAPACITANCE Parameter Symbol CIN COUT CIN2 Parameter Description Input Capacitance Output Capacitance Control Pin Capacitance Test Setup VIN = 0 VOUT = 0 VIN = 0 Typ. 7.5 8 10 Max. 9.5 10 13 Unit pF pF pF Note: Test conditions TA = 25C, f = 1.0 MHz s FBGA PIN CAPACITANCE Parameter Symbol CIN COUT CIN2 Parameter Description Input Capacitance Output Capacitance Control Pin Capacitance Test Setup VIN = 0 VOUT = 0 VIN = 0 Typ. 7.5 8 10 Max. 9.5 10 13 Unit pF pF pF Note: Test conditions TA = 25C, f = 1.0 MHz 53 MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 s PACKAGE DIMENSIONS 48-pin plastic TSOP (I) (FPT-48P-M19) LEAD No. 1 48 *: Resin protruction. (Each side: 0.15(.006) Max) INDEX Details of "A" part 0.15(.006) MAX "A" 0.15(.006) 0.35(.014) MAX 0.25(.010) 24 25 20.000.20 (.787.008) * 18.400.20 (.724.008) * 12.000.20 (.472.008) 11.50REF (.460) 1.10 -0.05 +.004 .043 -.002 (MOUNTING HEIGHT) 0.05(0.02)MIN STAND OFF +0.10 0.10(.004) 0.50(.0197) TYP 0.150.05 (.006.002) 0.200.10 (.008.004) 0.10(.004) M 19.000.20 (.748.008) 0.500.10 (.020.004) C 1996 FUJITSU LIMITED F48029S-2C-2 Dimensions in mm (inches) (Continued) 54 MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 48-pin plastic TSOP (I) (FPT-48P-M20) LEAD No. 1 48 *: Resin protrusion. (Each side: 0.15(.006) Max) INDEX Details of "A" part 0.15(.006) MAX "A" 0.15(.006) 0.35(.014) MAX 0.25(.010) 24 25 19.000.20 (.748.008) 0.500.10 (.020.004) 0.150.10 (.006.002) 0.200.10 (.008.004) 0.10(.004) M 0.10(.004) 0.50(.0197) TYP 0.05(0.02)MIN STAND OFF * 18.400.20 (.724.008) 20.000.20 (.787.008) 11.50(.460)REF * 12.000.20(.472.008) 1.10 -0.05 +.004 .043 -.002 (MOUNTING HEIGHT) +0.10 C 1996 FUJITSU LIMITED F48030S-2C-2 Dimensions in mm (inches) (Continued) 55 MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 46-pin plastic SON (LCC-46P-M02) Note 1) Resin residue for * marked dimensions is 0.15 max on a single side. Note 2) Die pad geometry may change with the models. *12.000.10(.472.004) 46 24 0.75(.030)MAX (TOTAL HEIGHT) 0.50(.020)TYP "A" 10.100.20 (.398.008) 10.000.10 (.394.004) 1 23 INDEX 0.05(.002) M Details of "B" part "B" 0.10(.004)TYP Details of "A" part *0.50(.020)TYP 0.05(.002) 0(0)MIN (STAND OFF) 0.50(.020)TYP 0.320.05 (.013.002) C 1997 FUJITSU LIMITED C46002S-4C-3 Dimensions in mm (inches) (Continued) 56 MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 (Continued) 48-pin plastic CSOP (LCC-48P-M03) 48 25 "A" 10.000.20 (.394.008) 9.500.10 (.374.004) INDEX INDEX 0.05 -0 +0.05 +.002 .002 -.0 (Stand off) LEAD No. 1 24 10.000.10(.394.004) 0.950.05(.037.002) (Mounting height) 0.220.035 (.009.001) Details of "A" part 0~10 0.65(.026) 1.15(.045) 0.40(.016) TYP 9.20(.362)REF 0.08(.003) C 1998 FUJITSU LIMITED C48056S-1C-1 Dimensions in mm (inches) (Continued) 57 MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 (Continued) 48-pin plastic FBGA (BGA-48P-M03) Note: The actual shape of corners may differ from the dimension. 9.000.20(.354.008) 1.20(.047)MAX (Mounting height) 0.350.10(.014.004) (Stand off) 5.60(.221) 0.80(.031)NOM 6 0.80(.031) NOM 4.00(.157) 5 4 3 2 1 H G F E D C B A 8.000.20 (.315.008) INDEX O0.400.10 (.016.004) O0.08(.003) M 0.10(.004) C 1997 FUJITSU LIMITED B48003S-1C-2 Dimensions in mm (inches) (Continued) 58 MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 (Continued) 48-pin plastic FBGA (BGA-48P-M13) Note: The actual shape of corners may differ from the dimension. 9.000.20(.354.008) 1.05 -0.10 .041 -.004 (Mounting height) 0.380.10(.015.004) (Stand off) +0.15 +.006 5.60(.221) 0.80(.031)TYP 6 5 8.000.20 (.315.008) INDEX 4 4.00(.157) 3 2 1 H C0.25(.010) G F E D C B A M 48-O0.450.10 (48-.018.004) O0.08(.003) 0.10(.004) C 1998 FUJITSU LIMITED B480013S-1C-1 Dimensions in mm (inches) 59 MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 FUJITSU LIMITED For further information please contact: Japan FUJITSU LIMITED Corporate Global Business Support Division Electronic Devices KAWASAKI PLANT, 4-1-1, Kamikodanaka Nakahara-ku, Kawasaki-shi Kanagawa 211-8588, Japan Tel: 81(44) 754-3763 Fax: 81(44) 754-3329 All Rights Reserved. The contents of this document are subject to change without notice. Customers are advised to consult with FUJITSU sales representatives before ordering. The information and circuit diagrams in this document are presented as examples of semiconductor device applications, and are not intended to be incorporated in devices for actual use. Also, FUJITSU is unable to assume responsibility for infringement of any patent rights or other rights of third parties arising from the use of this information or circuit diagrams. FUJITSU semiconductor devices are intended for use in standard applications (computers, office automation and other office equipment, industrial, communications, and measurement equipment, personal or household devices, etc.). CAUTION: Customers considering the use of our products in special applications where failure or abnormal operation may directly affect human lives or cause physical injury or property damage, or where extremely high levels of reliability are demanded (such as aerospace systems, atomic energy controls, sea floor repeaters, vehicle operating controls, medical devices for life support, etc.) are requested to consult with FUJITSU sales representatives before such use. The company will not be responsible for damages arising from such use without prior approval. Any semiconductor devices have an inhereut chance inherently a certain rate of failure. You must protect against injury, damage or loss from such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current levels and other abnormal operating conditions. If any products described in this document represent goods or technologies subject to certain restrictions on export under the Foreign Exchange and Foreign Trade Law of Japan, the prior authorization by Japanese government will be required for export of those products from Japan. http://www.fujitsu.co.jp/ North and South America FUJITSU MICROELECTRONICS, INC. Semiconductor Division 3545 North First Street San Jose, CA 95134-1804, USA Tel: (408) 922-9000 Fax: (408) 922-9179 Customer Response Center Mon. - Fri.: 7 am - 5 pm (PST) Tel: (800) 866-8608 Fax: (408) 922-9179 http://www.fujitsumicro.com/ Europe FUJITSU MIKROELEKTRONIK GmbH Am Siebenstein 6-10 D-63303 Dreieich-Buchschlag Germany Tel: (06103) 690-0 Fax: (06103) 690-122 http://www.fujitsu-ede.com/ Asia Pacific FUJITSU MICROELECTRONICS ASIA PTE LTD #05-08, 151 Lorong Chuan New Tech Park Singapore 556741 Tel: (65) 281-0770 Fax: (65) 281-0220 http://www.fmap.com.sg/ F9904 (c) FUJITSU LIMITED Printed in Japan 60 |
Price & Availability of MBM29LV160B-90PFTY
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |