Part Number Hot Search : 
SDR620Z TLC116 TQP3M9 ESAD39 LS7083 RJK0349 MN9100 IDTVS330
Product Description
Full Text Search
 

To Download MUR115 Datasheet File

  If you can't view the Datasheet, Please click here to try to view without PDF Reader .  
 
 


  Datasheet File OCR Text:
 MUR120 Series
Preferred Devices
SWITCHMODEE Power Rectifiers
MUR105, MUR110, MUR115, MUR120, MUR130, MUR140, MUR160
http://onsemi.com
. . . designed for use in switching power supplies, inverters and as free wheeling diodes, these state-of-the-art devices have the following features:
* * * * * *
Ultrafast 25, 50 and 75 Nanosecond Recovery Times 175C Operating Junction Temperature Low Forward Voltage Low Leakage Current High Temperature Glass Passivated Junction Reverse Voltage to 600 Volts
ULTRAFAST RECTIFIERS 1.0 AMPERE 50-600 VOLTS
Mechanical Characteristics:
* Case: Epoxy, Molded * Weight: 0.4 gram (approximately) * Finish: All External Surfaces Corrosion Resistant and Terminal * Lead and Mounting Surface Temperature for Soldering Purposes: * * * *
220C Max. for 10 Seconds, 1/16 from case Shipped in plastic bags, 1000 per bag Available Tape and Reeled, 5000 per reel, by adding a "RL'' suffix to the part number Polarity: Cathode Indicated by Polarity Band Marking: MUR105, MUR110, MUR115, MUR120, MUR130, MUR140, MUR160 Leads are Readily Solderable
AXIAL LEAD CASE 59-10 PLASTIC
MARKING DIAGRAM
MUR1xx
MAXIMUM RATINGS
Please See the Table on the Following Page
MUR1 = Device Code xx = Specific Device Code
ORDERING INFORMATION
See detailed ordering and shipping information in the package dimensions section on page 2 of this data sheet. Preferred devices are recommended choices for future use and best overall value.
(c) Semiconductor Components Industries, LLC, 2002
1
August, 2002 - Rev. 6
Publication Order Number: MUR120/D
MUR120 Series
MAXIMUM RATINGS
MUR Rating Peak Repetitive Reverse Voltage Working Peak Reverse Voltage DC Blocking Voltage Average Rectified Forward Current (Square Wave Mounting Method #3 Per Note 1.) Nonrepetitive Peak Surge Current (Surge applied at rated load conditions, halfwave, single phase, 60 Hz) Operating Junction Temperature and Storage Temperature Symbol VRRM VRWM VR IF(AV) IFSM 105 50 110 100 115 150 120 200 130 300 140 400 160 600 Unit Volts
1.0 @ TA = 130C 35
1.0 @ TA = 120C
Amps Amps
TJ, Tstg
*65 to +175
C
THERMAL CHARACTERISTICS
Maximum Thermal Resistance, Junction to Ambient RqJA See Note 1. C/W
ELECTRICAL CHARACTERISTICS
Maximum Instantaneous Forward Voltage (Note 1) (iF = 1.0 Amp, TJ = 150C) (iF = 1.0 Amp, TJ = 25C) Maximum Instantaneous Reverse Current (Note 1) (Rated dc Voltage, TJ = 150C) (Rated dc Voltage, TJ = 25C) Maximum Reverse Recovery Time (IF = 1.0 Amp, di/dt = 50 Amp/ms) (IF = 0.5 Amp, iR = 1.0 Amp, IREC = 0.25 A) Maximum Forward Recovery Time (IF = 1.0 A, di/dt = 100 A/ms, IREC to 1.0 V) 1. Pulse Test: Pulse Width = 300 ms, Duty Cycle 2.0%. vF 0.710 0.875 iR 50 2.0 trr 35 25 tfr 25 75 50 50 ns 150 5.0 ns 1.05 1.25 mA Volts
ORDERING INFORMATION
Device MUR105 MUR105RL MUR110 MUR110RL MUR115 MUR115RL MUR120 MUR120RL MUR130 MUR130RL MUR140 MUR140RL MUR160 MUR160RL Marking MUR105 MUR105 MUR110 MUR110 MUR115 MUR115 MUR120 MUR120 MUR130 MUR130 MUR140 MUR140 MUR160 MUR160 Package Axial Lead Axial Lead Axial Lead Axial Lead Axial Lead Axial Lead Axial Lead Axial Lead Axial Lead Axial Lead Axial Lead Axial Lead Axial Lead Axial Lead Shipping 1000 Units/Bag 5000 Units/Tape & Reel 1000 Units/Bag 5000 Units/Tape & Reel 1000 Units/Bag 5000 Units/Tape & Reel 1000 Units/Bag 5000 Units/Tape & Reel 1000 Units/Bag 5000 Units/Tape & Reel 1000 Units/Bag 5000 Units/Tape & Reel 1000 Units/Bag 5000 Units/Tape & Reel
http://onsemi.com
2
MUR120 Series
MUR105, MUR110, MUR115, MUR120
10 IR, REVERSE CURRENT (m A) 7.0 5.0 100 TJ = 175C 10
1.0
100C
3.0 TJ = 175C i , INSTANTANEOUS FORWARD CURRENT (AMPS) F 2.0 25C 1.0 0.7 0.5 100C
0.1
0.01
25C
0.001 0 20 40 60 80 100 120 140 160 180 200 VR, REVERSE VOLTAGE (VOLTS)
Figure 2. Typical Reverse Current*
0.3 0.2 5.0 * The curves shown are typical for the highest voltage device in the voltage grouping. Typical reverse current for lower voltage selections can be estimated from these same curves if VR is sufficiently below rated VR. IF(AV) , AVERAGE FORWARD CURRENT (AMPS)
0.1 0.07 0.05
4.0
RATED VR RqJA = 50C/W
3.0
0.03 0.02
2.0 SQUARE WAVE 1.0 0 0 50 100
dc
0.01 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 vF, INSTANTANEOUS VOLTAGE (VOLTS)
150
200
250
Figure 1. Typical Forward Voltage
TA, AMBIENT TEMPERATURE (C)
Figure 3. Current Derating (Mounting Method #3 Per Note 1)
PF(AV) , AVERAGE POWER DISSIPATION (WATTS) 5.0 TJ = 175C 4.0 I (CAPACITIVE LOAD) PK + 20 I 10 5.0 C, CAPACITANCE (pF) 50 TJ = 25C 30 20
AV
3.0
2.0 dc 1.0 SQUARE WAVE 0 0 0.5 1.0 1.5 2.0 2.5 IF(AV), AVERAGE FORWARD CURRENT (AMPS)
10 7.0 5.0 0 10 20 30 40 50 VR, REVERSE VOLTAGE (VOLTS)
Figure 4. Power Dissipation
Figure 5. Typical Capacitance
http://onsemi.com
3
MUR120 Series
MUR130, MUR140, MUR160
10 IR, REVERSE CURRENT (m A) 7.0 5.0 400 100 40 10 4.0 1.0 0.4 0.1 0.04 0.01 0.004 0 100 200 300 400 500 600 700 VR, REVERSE VOLTAGE (VOLTS) 25C 100C TJ = 175C
3.0 TJ = 175C i , INSTANTANEOUS FORWARD CURRENT (AMPS) F 2.0 25C
100C
1.0 0.7 0.5
Figure 7. Typical Reverse Current*
0.3 0.2 5.0 * The curves shown are typical for the highest voltage device in the voltage grouping. Typical reverse current for lower voltage selections can be estimated from these same curves if VR is sufficiently below rated VR. IF(AV) , AVERAGE FORWARD CURRENT (AMPS)
0.1 0.07 0.05
4.0
RATED VR RqJA = 50C/W
3.0
0.03 0.02
2.0 dc 1.0 SQUARE WAVE 0 0 50 100 150 200 250 TA, AMBIENT TEMPERATURE (C)
0.01 0.3 0.5 0.7 0.9 1.1 1.3 1.5 1.7 1.9 2.1 2.3 vF, INSTANTANEOUS VOLTAGE (VOLTS)
Figure 6. Typical Forward Voltage
Figure 8. Current Derating (Mounting Method #3 Per Note 1)
PF(AV) , AVERAGE POWER DISSIPATION (WATTS) 5.0 TJ = 175C 4.0 C, CAPACITANCE (pF) 5.0 3.0 (CAPACITIVE LOAD) I 2.0 I 10 dc SQUARE WAVE 1.0 0 0 0.5 1.0 1.5 2.0 2.5 IF(AV), AVERAGE FORWARD CURRENT (AMPS) 10 7.0 5.0 TJ = 25C 20
PK + 20 AV
3.0 2.0 0 10 20 30 40 50 VR, REVERSE VOLTAGE (VOLTS)
Figure 9. Power Dissipation
Figure 10. Typical Capacitance
http://onsemi.com
4
MUR120 Series
NOTE 1. -- AMBIENT MOUNTING DATA
Data shown for thermal resistance junction to ambient (RqJA) for the mountings shown is to be used as typical guideline values for preliminary engineering or in case the tie point temperature cannot be measured.
TYPICAL VALUES FOR RqJA IN STILL AIR Mounting Method 1 2 RqJA 3 Lead Length, L 1/4 1/2 1/8 52 65 72 67 80 87 50 Units C/W C/W C/W
MOUNTING METHOD 1
L
L
EEEEEEEEEEEE EEEEEEEEEEEE
Vector Pin Mounting MOUNTING METHOD 3
EEEEEEEEEEE EEEEEEEEEEE
MOUNTING METHOD 2
L L
EE EE EE EE EE EE EE
L = 3/8
Board Ground Plane
P.C. Board with 1-1/2 X 1-1/2 Copper Surface
http://onsemi.com
5
MUR120 Series
PACKAGE DIMENSIONS
MINI MOSORB CASE 59-10 ISSUE S
B
K F
D
NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. 59-04 OBSOLETE, NEW STANDARD 59-09. 4. 59-03 OBSOLETE, NEW STANDARD 59-10. 5. ALL RULES AND NOTES ASSOCIATED WITH JEDEC DO-41 OUTLINE SHALL APPLY 6. POLARITY DENOTED BY CATHODE BAND. 7. LEAD DIAMETER NOT CONTROLLED WITHIN F DIMENSION. DIM A B D F K INCHES MIN MAX 0.161 0.205 0.079 0.106 0.028 0.034 --- 0.050 1.000 --- MILLIMETERS MIN MAX 4.10 5.20 2.00 2.70 0.71 0.86 --- 1.27 25.40 ---
A F K
http://onsemi.com
6
MUR120 Series
Notes
http://onsemi.com
7
MUR120 Series
SWITCHMODE is a trademark of Semiconductor Components Industries, LLC.
ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer.
PUBLICATION ORDERING INFORMATION
Literature Fulfillment: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: ONlit@hibbertco.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada JAPAN: ON Semiconductor, Japan Customer Focus Center 2-9-1 Kamimeguro, Meguro-ku, Tokyo, Japan 153-0051 Phone: 81-3-5773-3850 Email: r14525@onsemi.com ON Semiconductor Website: http://onsemi.com For additional information, please contact your local Sales Representative.
http://onsemi.com
8
MUR120/D


▲Up To Search▲   

 
Price & Availability of MUR115

All Rights Reserved © IC-ON-LINE 2003 - 2022  

[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy]
Mirror Sites :  [www.datasheet.hk]   [www.maxim4u.com]  [www.ic-on-line.cn] [www.ic-on-line.com] [www.ic-on-line.net] [www.alldatasheet.com.cn] [www.gdcy.com]  [www.gdcy.net]


 . . . . .
  We use cookies to deliver the best possible web experience and assist with our advertising efforts. By continuing to use this site, you consent to the use of cookies. For more information on cookies, please take a look at our Privacy Policy. X