 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Preliminary Data Sheet No. PD 10057-D Series PVY116 Microelectronic Power IC HEXFET(R) Power MOSFET Photovoltaic Relay Single-Pole, Normally-Open, 0-40V AC/DC, 300mA General Description The PVY116 Series Photovoltaic Relay is a singlepole, normally-open solid-state relay that can replace dry and Mercury-wetted reed relays in many applications. It utilizes International Rectifier's proprietary HEXFET power MOSFET as the output switch, driven by an integrated circuit photovoltaic generator of novel construction. The output switch is controlled by radiation from a GaAlAs light emitting diode (LED), which is optically isolated from the photovoltaic generator. The PVY116 is ideally suited for use as matrix relay in low voltage ATE applications and general instrumentation applications involving high frequency test signals. This can be accomplished thanks to the extremely low Figure Of Merit (FOM = Coff * Ron), which is the product of the relay's off-state output capacitance and on-state resistance. The PVY116 is packaged in a 4-pin, molded small outline package (SOP-4) with surface mount (gull wing) terminals. It is available in plastic shipping tubes or on tape-and-reel. Please refer to Part Identification information. Features Low signal distortion at high frequencies Low Coff * Ron Figure Of Merit High off-state resistance Bounce-free operation 1,500 VRMS I/O isolation Long operational life Solid-State Reliability ESD Tolerance 2000V Human Body Model Applications Automated Test Equipment Instrumentation Data Acquisition Part Identification PVY116 PVY116-T surface-mount surface-mount, tape-and-reel (HEXFET is the registered trademark for International Rectifier's power MOSFETs) Series PVY116 Electrical Specifications (-40C TA +85C unless otherwise specified) INPUT CHARACTERISTICS Minimum control current (see Figure 1) Control current for off-state resistance @TA = +25C Control current range (caution: current limit input LED, see Figure 8) Reverse voltage Units mA mA mA V Min 2.0 -- 2.0 -- Typ -- -- -- -- Max -- 0.2 20.0 7.0 OUTPUT CHARACTERISTICS Operating voltage range Continuous load current @ 40C, 5mA control (see Figure 1) Pulsed load current @ 25C, 5mA control (see Figure 2 and 3) Off-state leakage @ 32V, 25C, (see Figure 4) On-state resistance @ 5mA control, IL =100mA (see Figure 2 and 3) Output capacitance Vd=0V, f=1MHz (Cout, see Figure 7) C * R (RDDon x Cout) Turn-on time, 5mA control, 100, 20V (Ton, see Figure 5) Turn-off time, 5mA control, 100, 20V (Toff, see Figure 5) Units V peak mA mA nA pF pF * S S Min -- -- -- -- -- -- -- -- -- Typ -- -- -- 0.02 3.5 2.4 8.5 110 100 Max 40 250 460 1.0 -- -- -- 500 500 GENERAL CHARACTERISTICS Dielectric strength, Input to Output Insulation Resistance, Input to Output CI-O (Input to Output Capacitance), Vd = 0V, f = 1MHz Max. pin soldering temperature (10 seconds max.) Ambient temperature range: Operating Storage Units VRMS pF oC oC oC Min 1500 1012 -- -40 -40 Typ -- -- 0.8 Max -- -- -- +260 +85 +100 Connection Diagram 2 www.irf.com Series PVY116 3000 600 Load Current (mA) 2500 Max Load Current (mA) 500 400 300 200 100 -2.5 -2.0 -1.5 -1.0 - 0.5 0.0 0.5 -100 -200 1.0 1.5 2.0 2.5 ILED = 5mA 2000 ILED = 2mA 1500 1000 500 00 0 20 40 60 (oC) -300 -400 -500 -600 Pulsed, 25 C o 80 100 Voltage Drop (VDD) Ambient Temperature Figure 1. Current Derating Curves Figure 2. Typical On Characteristics 500 450 400 Load Current (mA) Leakage Current (A) Pulsed, 20mS, 25 C o 1.0E-07 1.0E-08 25 C o 40 C o 60 C o 85 C o 350 300 250 200 150 100 50 0 0.0 0.5 1.0 1.5 2.0 ILED = 5mA 32V 1.0E-09 20V 1.0E-10 1.0E-11 2.5 3.0 1.0E-12 20 30 40 50 60 o 70 80 90 100 VDD (Volts) Ambient Temperature ( C) Figure 3. Typical On Characteristics Figure 4. Typical Leakage Characteristics www.irf.com 3 Series PVY116 1000 Delay Time (S) Tdly 100 Ton Toff I LED 90% I D 10% tdly ton toff 10 0 5 ILED (mA) 10 15 Figure 5. Typical Delay Times Figure 6. Delay Time Definitions 6 5 Typical Capacitance (pF) Input Current (mA) 20 16 5C lim 4 3 2 1 0 0 5 10 15 20 25 30 VDD Drain to Drain Voltage TYPICA L ice & +8 8 4 0 0 0.5 min. dev 1.0 max. devi ce & -45C 12 limit it 1.5 2.0 LED Forward Voltage Drop (Volts DC) Figure 7. Output Capacitance Figure 8. Input Characteristics (Current Controlled) 4 www.irf.com Series PVY116 Case Outlines - 4 Lead SOP 01-2027 01 IR WORLD HEADQUARTERS: 233 Kansas Street, El Segundo, California 90245 Tel: (310) 252-7105 Data and specifications subject to change without notice. 1/2/2002 www.irf.com 5 |
Price & Availability of SERIESPVY116
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |