View LT6201_458866.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

LT6200/LT6200-5 LT6200-10/LT6201 165MHz, Rail-to-Rail Input and Output, 0.95nV/Hz Low Noise, Op Amp Family
FEATURES
s s
DESCRIPTIO
s s s s s s s s s s
Low Noise Voltage: 0.95nV/Hz (100kHz) Gain Bandwidth Product: LT6200/LT6201 165MHz AV = 1 LT6200-5 800MHz AV 5 LT6200-10 1.6GHz AV 10 Low Distortion: -80dB at 1MHz, RL = 100 Dual LT6201 in Tiny DFN Package Input Common Mode Range Includes Both Rails Output Swings Rail-to-Rail Low Offset Voltage: 1mV Max Wide Supply Range: 2.5V to 12.6V Output Current: 60mA Min SOT-23 and SO-8 Packages Operating Temperature Range -40C to 85C Power Shutdown, Thermal Shutdown
The LT(R)6200/LT6201 are single and dual ultralow noise, rail-to-rail input and output unity gain stable op amps that feature 0.95nV/Hz noise voltage. These amplifiers combine very low noise with a 165MHz gain bandwidth, 50V/s slew rate and are optimized for low voltage signal conditioning systems. A shutdown pin reduces supply current during standby conditions and thermal shutdown protects the part from overload conditions. The LT6200-5/LT6200-10 are single amplifiers optimized for higher gain applications resulting in higher gain bandwidth and slew rate. The LT6200 family maintains its performance for supplies from 2.5V to 12.6V and are specified at 3V, 5V and 5V. For compact layouts the LT6200/LT6200-5/LT6200-10 are available in the 6-lead ThinSOTTM and the 8-pin SO package. The dual LT6201 is available in an 8-pin SO package with standard pinouts as well as a tiny, dual fine pitch leadless package (DFN). These amplifiers can be used as plug-in replacements for many high speed op amps to improve input/output range and noise performance.
, LTC and LT are registered trademarks of Linear Technology Corporation. ThinSOT is a trademark of Linear Technology Corporation.
APPLICATIO S
s s s s s
Transimpedance Amplifiers Low Noise Signal Processing Active Filters Rail-to-Rail Buffer Amplifiers Driving A/D Converters
TYPICAL APPLICATIO
5V
Single Supply, 1.5nV/Hz, Photodiode Amplifier
CF
DISTORTION (dBc)
-50
AV = 1 VO = 2VP-P -60 VS = 2.5V -70 HD2, RL = 1k -80 HD2, RL = 100 -90 HD3, RL = 100 HD3, RL = 1k
IPD
PHILIPS BF862
RF 10k
PHOTO DIODE
1k
LT6200
VOUT 2V +IPD * RF
-100 -110 100k
6200 TA01
10k
0.1F
U
Distortion vs Frequency
1M FREQUENCY (Hz) 10M
6200 G35
+
-
U
U
62001fa
1
LT6200/LT6200-5 LT6200-10/LT6201
ABSOLUTE
AXI U RATI GS
Total Supply Voltage (V+ to V-) ............................ 12.6V Total Supply Voltage (V+ to V-) (LT6201DD) ............. 7V Input Current (Note 2) ........................................ 40mA Output Short-Circuit Duration (Note 3) ............ Indefinite Pin Current While Exceeding Supplies (Note 12) ............................................................ 30mA Operating Temperature Range (Note 4) ...-40C to 85C
PACKAGE/ORDER I FOR ATIO
ORDER PART NUMBER LT6200CS6 LT6200IS6 LT6200CS6-5 LT6200IS6-5 LT6200CS6-10 LT6200IS6-10 S6 PART MARKING* LTJZ LTACB LTACC
TOP VIEW OUT 1 V- 2 +IN 3 6 V+ 5 SHDN 4 -IN
S6 PACKAGE 6-LEAD PLASTIC SOT-23
TJMAX = 150C, JA = 160C/W (Note 10)
TOP VIEW OUT A 1 -IN A 2 +IN A 3 V- 4 A B 8 7 6 5 V+ OUT B -IN B +IN B
ORDER PART NUMBER LT6201CDD DD PART MARKING* LADG
OUT A 1 -IN A 2 +IN A 3 V
-
- +
DD PACKAGE 8-LEAD (3mm x 3mm) PLASTIC DFN
TJMAX = 125C, JA = 160C/W (NOTE 3) UNDERSIDE METAL CONNECTED TO V -
*The temperature grade is identified by a label on the shipping container. Consult LTC Marketing for parts specified with wider operating temperature ranges.
2
U
U
W
WW U
W
(Note 1)
Specified Temperature Range (Note 5) ....-40C to 85C Junction Temperature ........................................... 150C Junction Temperature (DD Package) ................... 125C Storage Temperature Range ..................-65C to 150C Storage Temperature Range (DD Package) ...................................... - 65C to 125C Lead Temperature (Soldering, 10 sec).................. 300C
ORDER PART NUMBER LT6200CS8 LT6200IS8 LT6200CS8-5 LT6200IS8-5 LT6200CS8-10 LT6200IS8-10 S8 PART MARKING 6200 6200I 62005 6200I5 620010 200I10 ORDER PART NUMBER
+ 8V
TOP VIEW SHDN 1 -IN 2 +IN 3 V
-
- +
8 NC 7 V+ 6 OUT 5 NC
4
S8 PACKAGE 8-LEAD PLASTIC SO
TJMAX = 150C, JA = 100C/W
TOP VIEW
7 OUT B
- +
6 -IN B 5 +IN B
LT6201CS8 LT6201IS8 S8 PART MARKING 6201 6201I
4
S8 PACKAGE 8-LEAD PLASTIC SO
TJMAX = 150C, JA = 100C/W
62001fa
LT6200/LT6200-5 LT6200-10/LT6201
ELECTRICAL CHARACTERISTICS
VSHDN = OPEN, unless otherwise noted.
SYMBOL VOS PARAMETER Input Offset Voltage
TA = 25C, VS = 5V, 0V; VS = 3V, 0V; VCM = VOUT = half supply,
CONDITIONS VS = 5V, VCM =Half Supply VS = 3V, VCM = Half Supply VS = 5V, VCM = V + to V - VS = 3V, VCM = V + to V - VCM = Half Supply VCM = V - to V + VCM = Half Supply VCM = V+ VCM = V - VCM = V - to V+ VCM = V - to V+ VCM = Half Supply VCM = V+ VCM = V - 0.1Hz to 10Hz f = 100kHz, VS = 5V f = 10kHz, VS = 5V MIN TYP 0.1 0.9 0.6 1.8 0.2 0.5 -10 8 -23 31 0.3 0.1 0.02 0.4 600 1.1 1.5 2.2 3.5 0.57 2.1 3.1 4.2 70 11 17 65 85 60 80 60 65 2.5 No Load ISINK = 5mA VS = 5V, ISINK = 20mA VS = 3V, ISINK = 20mA No Load ISOURCE = 5mA VS = 5V, ISOURCE = 20mA VS = 3V, ISOURCE = 20mA VS = 5V VS = 3V VS = 5V VS = 3V VSHDN = 0.3V VSHDN = 0.3V V+ - 0.5 60 50 9 50 150 160 55 95 220 240 90 80 16.5 15 1.3 200 20 18 1.8 280 0.3 50 100 290 300 110 190 400 450 120 18 70 90 112 85 105 68 100 MAX 1 2.5 2 4 1.1 2.2 18 68 5 4 4 5 UNITS mV mV mV mV mV mV A A A A A A A A nVP-P nV/Hz nV/Hz pA/Hz pA/Hz M k pF pF V/mV V/mV V/mV dB dB dB dB dB dB V mV mV mV mV mV mV mV mV mA mA mA mA mA A V V
62001fa
IB IB IOS
Input Offset Voltage Match (Channel-to-Channel) (Note 11) Input Bias Current
- 40 - 50
IB Shift IB Match (Channel-to-Channel) (Note 11) Input Offset Current
Input Noise Voltage en in Input Noise Voltage Density
2.4
Input Noise Current Density, Balanced Source f = 10kHz, VS = 5V Unbalanced Source f = 10kHz, VS = 5V Input Resistance Common Mode Differential Mode Common Mode Differential Mode VS = 5V, VO = 0.5V to 4.5V, RL = 1k to VS/2 VS = 5V, VO = 1V to 4V, RL = 100 to VS/2 VS = 3V, VO = 0.5V to 2.5V, RL = 1k to VS/2 VS = 5V, VCM = V - to V+ VS = 5V, VCM = 1.5V to 3.5V VS = 3V, VCM = V - to V+ VS = 5V, VCM = 1.5V to 3.5V VS = 2.5V to 10V, LT6201DD VS = 2.5V to 7V VS = 2.5V to 10V, LT6201DD VS = 2.5V to 7V
CIN AVOL
Input Capacitance Large-Signal Gain
CMRR
Common Mode Rejection Ratio
CMRR Match (Channel-to-Channel) (Note 11) PSRR Power Supply Rejection Ratio PSRR Match (Channel-to-Channel) (Note 11) Minimum Supply Voltage (Note 6) VOL Output Voltage Swing LOW (Note 7)
VOH
Output Voltage Swing HIGH (Note 7)
ISC IS
Short-Circuit Current Supply Current per Amplifier Disabled Supply Current per Amplifier
ISHDN VL VH
SHDN Pin Current VSHDN Pin Input Voltage LOW VSHDN Pin Input Voltage HIGH
3
LT6200/LT6200-5 LT6200-10/LT6201
ELECTRICAL CHARACTERISTICS
VSHDN = OPEN, unless otherwise noted.
SYMBOL tON tOFF GBW PARAMETER Shutdown Output Leakage Current Turn-On Time Turn-Off Time Gain Bandwidth Product
TA = 25C, VS = 5V, 0V; VS = 3V, 0V; VCM = VOUT = half supply,
CONDITIONS VSHDN = 0.3V VSHDN = 0.3V to 4.5V, RL = 100, VS = 5V VSHDN = 4.5V to 0.3V, RL = 100, VS = 5V Frequency = 1MHz, VS = 5V LT6200-5 LT6200-10 VS = 5V, AV = -1, RL = 1k, VO = 4V VS = 5V, AV = -10, RL = 1k, VO = 4V LT6200-5 LT6200-10 31 MIN TYP 0.1 130 180 145 750 1450 44 210 340 3.28 4.66 165 MAX 75 UNITS A ns ns MHz MHz MHz V/s V/s V/s MHz ns
SR
Slew Rate
FPBW tS
Full Power Bandwidth (Note 9) Settling Time (LT6200, LT6201)
VS = 5V, VOUT = 3VP-P (LT6200) 0.1%, VS = 5V, VSTEP = 2V, AV = -1, RL = 1k
The q denotes the specifications which apply over 0C < TA < 70C temperature range. VS = 5V, 0V; VS = 3V, 0V; VCM = VOUT = half supply, VSHDN = OPEN, unless otherwise noted.
SYMBOL VOS PARAMETER Input Offset Voltage CONDITIONS VS = 5V, VCM = Half Supply VS = 3V, VCM = Half Supply VS = 5V, VCM = V + to V - VS = 3V, VCM = V + to V - Input Offset Voltage Match (Channel-to-Channel) (Note 11) VOS TC IB Input Offset Voltage Drift (Note 8) Input Bias Current VCM = Half Supply VCM = V - to V + VCM = Half Supply VCM = Half Supply VCM = V + VCM = V - VCM = V- to V + VCM = V - to V + VCM = Half Supply VCM = V + VCM = V - VS = 5V, VO = 0.5V to 4.5V,RL = 1k to VS /2 VS = 5V, VO = 1.5V to 3.5V,RL = 100 to VS /2 VS = 3V, VO = 0.5V to 2.5V,RL = 1k to VS /2 VS = 5V, VCM = V - to V + VS = 5V, VCM = 1.5V to 3.5V VS = 3V, VCM = V - to V + VS = 5V, VCM = 1.5V to 3.5V VS = 3V to 10V, LT6201DD VS = 3V to 7V VS = 3V to 10V, LT6201DD VS = 3V to 7V No Load ISINK = 5mA VS = 5V, ISINK = 20mA VS = 3V, ISINK = 20mA No Load ISOURCE = 5mA VS = 5V, ISOURCE = 20mA VS = 3V, ISOURCE = 20mA
q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q
MIN
TYP 0.2 1.0 0.3 1.5 0.2 0.4 2.5
MAX 1.2 2.7 3 4 1.8 2.8 8 18 6 68 4 4 5
UNITS mV mV mV mV mV mV V/C A A A A A A A A V/mV V/mV V/mV dB dB dB dB dB dB V
- 40 - 50
-10 8 - 23 0.5 31 0.1 0.02 0.4
IB Match (Channel-to-Channel) (Note 11) IB IOS IB Shift Input Offset Current
AVOL
Large-Signal Gain
46 7.5 13 64 80 60 80 60 60 3
80 13 22 88 105 83 105 65 100 12 55 170 170 65 115 260 270 60 110 310 310 120 210 440 490
CMRR
Common Mode Rejection Ratio
CMRR Match (Channel-to-Channel) (Note 11) PSRR Power Supply Rejection Ratio PSRR Match (Channel-to-Channel) (Note 11) Minimum Supply Voltage (Note 6) VOL Output Voltage Swing LOW (Note 7)
mV mV mV mV mV mV mV mV
62001fa
VOH
Output Voltage Swing HIGH (Note 7)
4
LT6200/LT6200-5 LT6200-10/LT6201
The q denotes the specifications which apply over 0C < TA < 70C temperature range. VS = 5V, 0V; VS = 3V, 0V; VCM = VOUT = half supply, VSHDN = OPEN, unless otherwise noted.
SYMBOL ISC IS PARAMETER Short-Circuit Current Supply Current per Amplifier Disabled Supply Current per Amplifier ISHDN VL VH tON tOFF SR SHDN Pin Current VSHDN Pin Input Voltage LOW VSHDN Pin Input Voltage HIGH Shutdown Output Leakage Current Turn-On Time Turn-Off Time Slew Rate VSHDN = 0.3V VSHDN = 0.3V to 4.5V, RL = 100, VS = 5V VSHDN = 4.5V to 0.3V, RL = 100, VS = 5V VS = 5V, AV = -1, RL = 1k, VO = 4V AV = -10, RL = 1k, VO = 4V LT6200-5 LT6200-10 FPBW Full Power Bandwidth (Note 9) VS = 5V, VOUT = 3VP-P (LT6200) CONDITIONS VS = 5V VS = 3V VS = 5V VS = 3V VSHDN = 0.3V VSHDN = 0.3V
q q q q q q q q q q q q q q q
ELECTRICAL CHARACTERISTICS
MIN 60 45
TYP 90 75 20 19 1.35 215
MAX
UNITS mA mA
23 22 1.8 295 0.3
mA mA mA A V V A ns ns V/s V/s V/s MHz
V+ - 0.5 0.1 130 180 29 42 190 310 3.07 4.45 75
The q denotes the specifications which apply over -40C < TA < 85C temperature range. Excludes the LT6201 in the DD package (Note 3). VS = 5V, 0V; VS = 3V, 0V; VCM = VOUT = half supply, VSHDN = OPEN, unless otherwise noted. (Note 5)
SYMBOL VOS PARAMETER Input Offset Voltage CONDITIONS VS = 5V, VCM = Half Supply VS = 3V, VCM = Half Supply VS = 5V, VCM = V + to V - VS = 3V, VCM = V + to V - Input Offset Voltage Match (Channel-to-Channel) (Note 11) VOS TC IB IB IOS Input Offset Voltage Drift (Note 8) Input Bias Current VCM = Half Supply VCM = V - to V + VCM = Half Supply VCM = Half Supply VCM = V+ VCM = V - VCM = V - to V+ VCM = V- to V+ VCM = Half Supply VCM = V+ VCM = V - VS = 5V, VO = 0.5V to 4.5V, RL = 1k to VS /2 VS = 5V, VO = 1.5V to 3.5V, RL = 100 to VS /2 VS = 3V, VO = 0.5V to 2.5V,RL = 1k to VS /2 VS = 5V, VCM = V - to V+ VS = 5V, VCM = 1.5V to 3.5V VS = 3V, VCM = V - to V+ VS = 3V to 10V VS = 3V to 10V No Load ISINK = 5mA VS = 5V, ISINK = 20mA VS = 3V, ISINK = 20mA
q q q q q q q q q q q q q q q q q q q q q q q q q q q q q
MIN
TYP 0.2 1.0 0.3 1.5 0.2 0.4 2.5
MAX 1.5 2.8 3.5 4.3 2 3 8.0 18 68 9 4 4 5
UNITS mV mV mV mV mV mV V/C A A A A A A A A V/mV V/mV V/mV dB dB dB dB dB dB V
-40 -50
-10 8 -23 31 1 0.1 0.02 0.4
IB Shift IB Match (Channel-to-Channel) (Note 11) Input Offset Current
AVOL
Large-Signal Gain
40 7.5 11 60 80 60 75 60 60 3
70 13 20 80 100 80 105 68 100 18 60 170 175 70 120 310 315
CMRR
Common Mode Rejection Ratio
CMRR Match (Channel-to-Channel) (Note 11) VS = 5V, VCM = 1.5V to 3.5V PSRR Power Supply Rejection Ratio PSRR Match (Channel-to-Channel) (Note 11) Minimum Supply Voltage (Note 6) VOL Output Voltage Swing LOW (Note 7)
mV mV mV mV
62001fa
5
LT6200/LT6200-5 LT6200-10/LT6201
ELECTRICAL CHARACTERISTICS
SYMBOL VOH PARAMETER Output Voltage Swing HIGH (Note 7)
The q denotes the specifications which apply over -40C < TA < 85C temperature range. Excludes the LT6201 in the DD package (Note 3). VS = 5V, 0V; VS = 3V, 0V; VCM = VOUT = half supply, VSHDN = OPEN, unless otherwise noted. (Note 5)
CONDITIONS No Load ISOURCE = 5mA VS = 5V, ISOURCE = 20mA VS = 3V, ISOURCE = 20mA VS = 5V VS = 3V VS = 5V VS = 3V VSHDN = 0.3V VSHDN = 0.3V
q q q q q q q q q q q q V+ - 0.5
MIN
TYP 65 115 270 280
MAX 120 210 450 500
UNITS mV mV mV mV mA mA
ISC IS
Short-Circuit Current Supply Current per Amplifier Disabled Supply Current per Amplifier
50 30
80 60 22 20 1.4 220 25.3 23 1.9 300 0.3 0.1 130 180 75
mA mA mA A V V A ns ns V/s V/s V/s MHz
ISHDN VL VH tON tOFF SR
SHDN Pin Current VSHDN Pin Input Voltage LOW VSHDN Pin Input Voltage HIGH Shutdown Output Leakage Current Turn-On Time Turn-Off Time Slew Rate
VSHDN = 0.3V VSHDN = 0.3V to 4.5V, RL = 100, VS = 5V VSHDN = 4.5V to 0.3V, RL = 100, VS = 5V VS = 5V, AV = -1, RL = 1k, VO = 4V AV = -10, RL = 1k, VO = 4V LT6200-5 LT6200-10
q q q q q q q
23
33 160 260
FPBW
Full Power Bandwidth (Note 9)
VS = 5V, VOUT = 3VP-P (LT6200)
2.44
3.5
TA = 25C, VS = 5V, VCM = VOUT = 0V, VSHDN = OPEN, unless otherwise noted. Excludes the LT6201 in the DD package (Note 3).
SYMBOL VOS PARAMETER Input Offset Voltage CONDITIONS VCM = Half Supply VCM = V+ VCM = V - VCM = 0V VCM = V - to V + VCM = Half Supply VCM = V+ VCM = V - VCM = V - to V+ VCM VCM = Half Supply VCM = V+ VCM = V - 0.1Hz to 10Hz f = 100kHz f = 10kHz f = 10kHz f = 10kHz Common Mode Differential Mode Common Mode Differential Mode VO = 4.5V, RL = 1k VO = 2V, RL = 100 = V- to V+ MIN TYP 1.4 2.5 2.5 0.2 0.4 -10 8 -23 31 0.2 1.3 1 3 600 0.95 1.4 2.2 3.5 0.57 2.1 3.1 4.2 200 26 MAX 4 6 6 1.6 3.2 18 68 6 7 7 12 UNITS mV mV mV mV mV A A A A A A A A nVP-P nV/Hz nV/Hz pA/Hz pA/Hz M k pF pF V/mV V/mV
62001fa
IB IB IOS
Input Offset Voltage Match (Channel-to-Channel) (Note 11) Input Bias Current
- 40 - 50
IB Shift IB Match (Channel-to-Channel) (Note 11) Input Offset Current
en in
Input Noise Voltage Input Noise Voltage Density Input Noise Current Density, Balanced Source Unbalanced Source Input Resistance Input Capacitance Large-Signal Gain
2.3
CIN AVOL
115 15
6
LT6200/LT6200-5 LT6200-10/LT6201
ELECTRICAL CHARACTERISTICS
noted. Excludes the LT6201 in the DD package (Note 3).
PARAMETER Common Mode Rejection Ratio CMRR Match (Channel-to-Channel) (Note 11) Power Supply Rejection Ratio PSRR Match (Channel-to-Channel) (Note 6) Output Voltage Swing LOW (Note 7) SYMBOL CMRR
TA = 25C, VS = 5V, VCM = VOUT = 0V, VSHDN = OPEN, unless otherwise
CONDITIONS VCM = V - to V+ VCM = -2V to 2V VCM = -2V to 2V VS = 1.25V to 5V VS = 1.25V to 5V No Load ISINK = 5mA ISINK = 20mA No Load ISOURCE = 5mA ISOURCE = 20mA 60 VSHDN = 0.3V VSHDN = 0.3V V+ - 0.5 VSHDN = 0.3V VSHDN = 0.3V to 4.5V, RL = 100, VS = 5V VSHDN = 4.5V to 0.3V, RL = 100, VS = 5V Frequency = 1MHz LT6200-5 LT6200-10 AV = -1, RL = 1k, VO = 4V AV = -10, RL = 1k, VO = 4V LT6200-5 LT6200-10 110 530 1060 35 175 315 33 0.1 130 180 165 800 1600 50 250 450 47 140 75 MIN 68 75 80 60 65 TYP 96 100 105 68 100 12 55 150 70 110 225 90 20 1.6 200 50 110 290 130 210 420 23 2.1 280 0.3 MAX UNITS dB dB dB dB dB mV mV mV mV mV mV mA mA mA A V V A ns ns MHz MHz MHz V/s V/s V/s MHz ns
PSRR VOL
VOH
Output Voltage Swing HIGH (Note 7)
ISC IS ISHDN VL VH tON tOFF GBW
Short-Circuit Current Supply Current per Amplifier Disabled Supply Current per Amplifier SHDN Pin Current VSHDN Pin Input Voltage LOW VSHDN Pin Input Voltage HIGH Shutdown Output Leakage Current Turn-On Time Turn-Off Time Gain Bandwidth Product
SR
Slew Rate
FPBW tS
Full Power Bandwidth (Note 9) Settling Time (LT6200, LT6201)
VOUT = 3VP-P (LT6200-10) 0.1%, VSTEP = 2V, AV = -1, RL = 1k
62001fa
7
LT6200/LT6200-5 LT6200-10/LT6201
The q denotes the specifications which apply over 0C < TA < 70C temperature range. Excludes the LT6201 in the DD package (Note 3). VS = 5V, VCM = VOUT = 0V, VSHDN = OPEN, unless otherwise noted.
SYMBOL VOS PARAMETER Input Offset Voltage CONDITIONS VCM = Half Supply VCM = V+ VCM = V - VCM = 0V VCM = V - to V + VCM = Half Supply VCM = Half Supply VCM = V+ VCM = V - VCM = V - to V+ VCM VCM = Half Supply VCM = V+ VCM = V - VO = 4.5V, RL = 1k VO = 2V, RL = 100 VCM = V - to V+ VCM = -2V to 2V VCM = -2V to 2V VS = 1.5V to 5V VS = 1.5V to 5V No Load ISINK = 5mA ISINK = 20mA No Load ISOURCE = 5mA ISOURCE = 20mA = V- to V+
q q q q q q q q q q q q q q q q q q q q q q q q q q q q
ELECTRICAL CHARACTERISTICS
MIN
TYP 1.9 3.5 3.5 0.2 0.4 8.2
MAX 4.5 7.5 7.5 1.8 3.4 24 18 68 9 10 10 15
UNITS mV mV mV mV mV V/C A A A A A A A A V/mV V/mV dB dB dB dB dB mV mV mV mV mV mV mA mA mA A V V A ns ns V/s V/s V/s MHz
VOS TC IB IB IOS
Input Offset Voltage Match (Channel-to-Channel) (Note 11) Input Offset Voltage Drift (Note 8) Input Bias Current
-40 -50
IB Shift IB Match (Channel-to-Channel) (Note 11) Input Offset Current
-10 8 -23 31 1 1.3 1.0 3.5
AVOL CMRR
Large-Signal Gain Common Mode Rejection Ratio CMRR Match (Channel-to-Channel) (Note 11)
46 7.5 65 75 75 60 60
80 13.5 90 100 105 65 100 16 60 170 85 125 265 90 25 1.6 215 70 120 310 150 230 480 29 2.1 295 0.3
PSRR VOL
Power Supply Rejection Ratio PSRR Match (Channel-to-Channel) (Note 6) Output Voltage Swing LOW (Note 7)
VOH
Output Voltage Swing HIGH (Note 7)
ISC IS ISHDN VL VH tON tOFF SR
Short-Circuit Current Supply Current per Amplifier Disabled Supply Current per Amplifier SHDN Pin Current VSHDN Pin Input Voltage LOW VSHDN Pin Input Voltage HIGH Shutdown Output Leakage Current Turn-On Time Turn-Off Time Slew Rate
60
VSHDN = 0.3V VSHDN = 0.3V
q q q q q
V+ - 0.5 0.1 130 31 150 290 30 180 44 215 410 43 75
VSHDN = 0.3V VSHDN = 0.3V to 4.5V, RL = 100, VS = 5V VSHDN = 4.5V to 0.3V, RL = 100, VS = 5V AV = -1, RL = 1k, VO = 4V AV = -10, RL = 1k, VO = 4V LT6200-5 LT6200-10 VOUT = 3VP-P (LT6200-10)
q q q q q q q
FPBW
Full Power Bandwidth (Note 9)
62001fa
8
LT6200/LT6200-5 LT6200-10/LT6201
The q denotes the specifications which apply over -40C < TA < 85C temperature range. Excludes the LT6201 in the DD package (Note 3). VS = 5V, VCM = VOUT = 0V, VSHDN = OPEN, unless otherwise noted. (Note 5)
SYMBOL VOS PARAMETER Input Offset Voltage CONDITIONS VCM = Half Supply VCM = V+ VCM = V - VCM = 0V VCM = V - to V + VCM = Half Supply VCM = Half Supply VCM = V+ VCM = V - VCM = V - to V+ VCM = Half Supply VCM = V+ VCM = V - VO = 4.5V, RL = 1k VO = 2V RL = 100 VCM = V - to V+ VCM = -2V to 2V VCM = -2V to 2V VS = 1.5V to 5V VS = 1.5V to 5V No Load ISINK = 5mA ISINK = 20mA No Load ISOURCE = 5mA ISOURCE = 20mA MIN
q q q q q q q q q q q q q q q q q q q q q q q q q q q q
ELECTRICAL CHARACTERISTICS
TYP 1.9 3.5 3.5 0.2 0.4
MAX 4.5 7.5 7.5 2.0 3.6 24 18 68 12 10 10 15
UNITS mV mV mV mV mV V/C A A A A A A A A V/mV V/mV dB dB dB dB
Input Offset Voltage Match (Channel-to-Channel) (Note 11) VOS TC IB IB IOS Input Offset Voltage Drift (Note 8) Input Bias Current
-40 -50
8.2 -10 8 -23 31 4 1.3 1.0 3.5 80 13.5 90 100 105 65 100 16 60 170 85 125 265 90 25 1.6 215
IB Shift IB Match (Channel-to-Channel) (Note 11) Input Offset Current
AVOL CMRR
Large-Signal Gain Common Mode Rejection Ratio CMRR Match (Channel-to-Channel) (Note 11) Power Supply Rejection Ratio PSRR Match (Channel-to-Channel) (Note 6) Output Voltage Swing LOW (Note 7)
46 7.5 65 75 75 60 60
PSRR VOL
75 125 310 150 230 480 29 2.1 295 0.3 75
dB mV mV mV mV mV mV mA mA mA A V V A ns ns V/s V/s V/s MHz
VOH
Output Voltage Swing HIGH (Note 7)
ISC IS ISHDN VL VH tON tOFF SR
Short-Circuit Current Supply Current Disabled Supply Current SHDN Pin Current VSHDN Pin Input Voltage LOW VSHDN Pin Input Voltage HIGH Shutdown Output Leakage Current Turn-On Time Turn-Off Time Slew Rate VSHDN = 0.3V VSHDN = 0.3V
60
q q q q q V+ - 0.5
VSHDN = 0.3V VSHDN = 0.3V to 4.5V, RL = 100, VS = 5V VSHDN = 4.5V to 0.3V, RL = 100, VS = 5V AV = -1, RL = 1k, VO = 4V AV = -10, RL = 1k, VO = 4V LT6200-5 LT6200-10 VOUT = 3VP-P (LT6200-10)
q q q q q q q
0.1 130 180 31 125 260 27 44 180 370 39
FPBW
Full Power Bandwidth (Note 9)
Note 1: Absolute maximum ratings are those values beyond which the life of the device may be impaired. Note 2: Inputs are protected by back-to-back diodes. If the differential input voltage exceeds 0.7V, the input current must be limited to less than 40mA. Note 3: A heat sink may be required to keep the junction temperature below the absolute maximum rating when the output is shorted
indefinitely. The LT6201 in the DD package is limited by power dissipation to VS 5V, 0V over the commercial temperature range only. Note 4: The LT6200C/LT6200I and LT6201C/LT6201I are guaranteed functional over the temperature range of -40C and 85C (LT6201DD excluded).
62001fa
9
LT6200/LT6200-5 LT6200-10/LT6201
ELECTRICAL CHARACTERISTICS
Note 5: The LT6200C/LT6201C are guaranteed to meet specified performance from 0C to 70C. The LT6200C/LT6201C are designed, characterized and expected to meet specified performance from - 40C to 85C, but are not tested or QA sampled at these temperatures. The LT6200I is guaranteed to meet specified performance from -40C to 85C. Note 6: Minimum supply voltage is guaranteed by power supply rejection ratio test. Note 7: Output voltage swings are measured between the output and power supply rails. Note 8: This parameter is not 100% tested. Note 9: Full-power bandwidth is calculated from the slew rate: FPBW = SR/2VP Note 10: Thermal resistance varies depending upon the amount of PC board metal attached to the V - pin of the device. JA is specified for a certain amount of 2oz copper metal trace connecting to the V - pin as described in the thermal resistance tables in the Application Information section. Note 11: Matching parameters on the LT6201 are the difference between the two amplifiers. CMRR and PSRR match are defined as follows: CMRR and PSRR are measured in V/V on the identical amplifiers. The difference is calculated in V/V. The result is converted to dB. Note 12: There are reverse biased ESD diodes on all inputs and outputs as shown in Figure 1. If these pins are forced beyond either supply, unlimited current will flow through these diodes. If the current is transient in nature and limited to less than 30mA, no damage to the device will occur.
TYPICAL PERFOR A CE CHARACTERISTICS
VOS Distribution, VCM = V +/2
80 70 60
NUMBER OF UNITS
VS = 5V, 0V SO-8
NUMBER OF UNITS
50 40 30 20 10 0 -1000 600 -600 -200 200 INPUT OFFSET VOLTAGE (V) 1000
6200 G01
50 40 30 20 10 0 -1600-1200 -800 -400 0 400 800 1200 1600 INPUT OFFSET VOLTAGE (V)
6200 G02
NUMBER OF UNITS
Supply Current vs Supply Voltage
30 TA = 125C 25 20 15 10 5 -1.0 0 0 2 8 12 6 10 4 TOTAL SUPPLY VOLTAGE (V) 14 -1.5 TA = -55C TA = 25C 1.5 1.0 0.5 0 -0.5 3.0 2.5 2.0
INPUT BIAS CURRENT (A)
SUPPLY CURRENT (mA)
OFFSET VOLTAGE (mV)
10
UW
6200 G04
VOS Distribution, VCM = V +
80 70 60 VS = 5V, 0V SO-8 80 70 60 50 40 30 20 10
VOS Distribution, VCM = V -
VS = 5V, 0V SO-8
0 -1600-1200 -800 -400 0 400 800 1200 1600 INPUT OFFSET VOLTAGE (V)
6200 G03
Offset Voltage vs Input Common Mode Voltage
VS = 5V, 0V TYPICAL PART 20 10 0 -10 -20 -30 -40 0 4 1 3 2 INPUT COMMON MODE VOLTAGE (V)
6200 G05
Input Bias Current vs Common Mode Voltage
VS = 5V, 0V
TA = 125C TA = 25C TA = -55C
TA = -55C TA = 25C TA = 125C
5
-1
0
3 5 2 4 1 COMMON MODE VOLTAGE (V)
6
6200 G06
62001fa
LT6200/LT6200-5 LT6200-10/LT6201 TYPICAL PERFOR A CE CHARACTERISTICS
Input Bias Current vs Temperature
20 15 VS = 5V, 0V VCM = 5V
INPUT BIAS CURRENT (A)
10 5 0 -5 -10 -15 -20 -25
OUTPUT SATURATION VOLTAGE (V)
1
OUTPUT SATURATION VOLTAGE (V)
VCM = 0V
-30 -50 -35 -20 - 5 10 25 40 55 TEMPERATURE (C)
Minimum Supply Voltage
1.0
CHANGE IN OFFSET VOTLAGE (mV)
OUTPUT SHORT-CIRCUIT CURRENT (mA)
VCM = VS/2
0.5 0 TA = -55C -0.5 -1.0 -1.5 -2.0 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 TOTAL SUPPLY VOLTAGE (V) 5 TA = 25C TA = 125C
INPUT VOLTAGE (mV)
Open-Loop Gain
2.5 2.0 1.5 INPUT VOLTAGE (mV) 1.0 0.5 0 -0.5 -1.0 -1.5 -2.0 -2.5 0 1 3 2 OUTPUT VOLTAGE (V) 4 5
6200 G13
VS = 5V, 0V TA = 25C INPUT VOLTAGE (mV)
OFFSET VOLTAGE (mV)
RL = 1k RL = 100
UW
70
6200 G07
Output Saturation Voltage vs Load Current (Output Low)
10 VS = 5V, 0V 10
Output Saturation Voltage vs Load Current (Output High)
VS = 5V, 0V
1
0.1 TA = 125C TA = -55C 0.01 TA = 25C
0.1
TA = 125C TA = 25C TA = -55C
85
0.001 0.1 1 10 LOAD CURRENT (mA) 100
6200 G08
0.01 0.1 1 10 LOAD CURRENT (mA) 100
6200 G09
Output Short-Circuit Current vs Power Supply Voltage
120 100 80 60 40 20 0 -20 -40 -60 -80 TA = 125C 1.5 2 3.5 3 2.5 4 4.5 POWER SUPPLY VOLTAGE (V) 5 SINKING TA = 25C SOURCING TA = 25C TA = 125C TA = -55C 2.5 2.0 1.5 1.0 0.5 0 -0.5 -1.0 -1.5 -2.0 -2.5
Open-Loop Gain
VS = 3V, 0V TA = 25C
RL = 1k RL = 100
TA = -55C
-100 -120
0
0.5
1.5 2 1 OUTPUT VOLTAGE (V)
2.5
3
6200 G12
6200 G10
6200 G11
Open-Loop Gain
2.5 2.0 1.5 1.0 0.5 0 - 0.5 -1.0 -1.5 -2.0 -2.5 -5 -4 -3 -2 -1 0 1 2 3 OUTPUT VOLTAGE (V) 4 5 RL = 1k RL = 100 VS = 5V TA = 25C
Offset Voltage vs Output Current
15 10 5 0 -5 -10 -15 -100 TA = 125C TA = -55C TA = 25C VS = 5V
-60 -20 20 60 OUTPUT CURRENT (mA)
100
6200 G15
6200 G14
62001fa
11
LT6200/LT6200-5 LT6200-10/LT6201 TYPICAL PERFOR A CE CHARACTERISTICS
Warm-Up Drift vs Time (LT6200S8)
300 TA = 25C TOTAL NOISE VOLTAGE (nV/Hz) VS = 5V
CHANGE IN OFFSET VOLTAGE (V)
250 200 150 100 VS = 1.5V 50 0 0 20 VS = 2.5V
10
NOISE VOLTAGE (nV/Hz)
40 60 80 100 120 140 160 TIME AFTER POWER-UP (SEC)
6200 G16
Balanced Noise Current vs Frequency
25 BALANCED NOISE CURRENT (pA/Hz) UNBALANCED NOISE CURRENT (pA/Hz) VS = 5V, 0V TA = 25C BALANCED SOURCE RESISTANCE
PNP ACTIVE VCM = 0.5V 15 BOTH ACTIVE VCM = 2.5V 10 NPN ACTIVE VCM = 4.5V 5
25 20 15 10 5 0
PNP ACTIVE VCM = 0.5V BOTH ACTIVE VCM = 2.5V NPN ACTIVE VCM = 4.5V
OUTPUT VOLTAGE NOISE (nV)
20
0 10 100 1k 10k FREQUENCY (Hz) 100k
6200 G19
Supply Current vs SHDN Pin Voltage
22 20 18
SUPPLY CURRENT (mA)
VS = 5V, 0V TA = 125C TA = 25C
16 14 12 10 8 6 4 2 0 0 1 TA = -55C
SHDN PIN CURRENT (A)
2 3 4 SHDN PIN VOLTAGE (V)
12
UW
Total Noise vs Source Resistance
100 VS = 5V VCM = 0V f = 100kHz UNBALANCED SOURCE RESISTORS
Input Noise Voltage vs Frequency
45 40 35 30 25 20 15 10 5 NPN ACTIVE VCM = 4.5V BOTH ACTIVE VCM = 2.5V PNP ACTIVE VCM = 0.5V VS = 5V, 0V TA = 25C
LT6200 TOTAL NOISE
RESISTOR NOISE 1 LT6200 AMPLIFIER NOISE VOLTAGE
0.1 10 100 1k 10k SOURCE RESISTANCE () 100k
6200 G17
0
10
100
1k FREQUENCY (Hz)
10k
100k
6200 G18
Unbalanced Noise Current vs Frequency
35 30 VS = 5V, 0V TA = 25C UNBALANCED SOURCE RESISTANCE
800 600 400 200 0
0.1Hz to 10Hz Output Noise Voltage
VS = 5V, 0V VCM = VS/2
-200 -400 -600
10
100
1k 10k FREQUENCY (Hz)
100k
6200 G20
-800 TIME (5SEC/DIV)
6200 G21
SHDN Pin Current vs SHDN Pin Voltage
50 0 -50 -100 TA = 125C -150 -200 -250 -300 5
6200 G43
VS = 5V, 0V TA = 25C TA = -55C
0
1
2
3
4
5
6200 G44
SHDN PIN VOLTAGE (V)
62001fa
LT6200/LT6200-5 LT6200-10/LT6201 TYPICAL PERFOR A CE CHARACTERISTICS LT6200, LT6201
Gain Bandwidth and Phase Margin vs Temperature
VS = 5V VS = 3V, 0V
GAIN BANDWIDTH (MHz)
GAIN (dB)
180 160 140 120 100 -50 -25
Open-Loop Gain vs Frequency
80 70 60 50 GAIN PHASE VS = 5V VS = 1.5V VS = 5V VS = 1.5V VCM = 0V CL = 5pF RL = 1k 1M 10M 100M FREQUENCY (Hz) 1G
6200 G24
GAIN BANDWIDTH (MHz)
GAIN (dB)
40 30 20 10 0 -10
-20 100k
Slew Rate vs Temperature
140 120 AV = -1 RF = RG = 1k RL = 1k VS = 5V RISING VS = 5V FALLING 80 60 40 20 0 -55 -35 -15 VS = 2.5V RISING VS = 2.5V FALLING
1000
COMMON MODE REJECTION RATIO (dB)
SLEW RATE (V/s)
100
OUTPUT IMPEDANCE ()
5 25 45 65 85 105 125 TEMPERATURE (C)
6200 G26
UW
Open-Loop Gain vs Frequency
70 60 50
PHASE MARGIN (DEG) 80 70 60 50 40 30 20 10 0 VCM = 4.5V VS = 5V, 0V CL = 5pF RL = 1k 1M 10M 100M FREQUENCY (Hz) 1G
6200 G23
120 PHASE VCM = 0.5V GAIN VCM = 4.5V 100 80 60
PHASE (DEG)
PHASE MARGIN
40
40 20
VS = 5V
VCM = 0.5V
0 -20 -40 -60 -80
VS = 3V, 0V GAIN BANDWIDTH
-10
0 25 50 75 TEMPERATURE (C)
100
125
-20 100k
6200 G22
Gain Bandwidth and Phase Margin vs Supply Voltage
120 100 80 60 TA = 25C RL = 1k CL = 5pF 80 70 PHASE MARGIN 60 50 40 30 180 160 140 120 100 80 0 2 8 6 4 10 12 TOTAL SUPPLY VOLTAGE (V) 14 GAIN BANDWIDTH
PHASE MARGIN (DEG)
PHASE (DEG)
40 20 0 -20 -40 -60 -80
6200 G25
Output Impedance vs Frequency
120
VS = 5V, 0V
Common Mode Rejection Ratio vs Frequency
VS = 5V, 0V VCM = VS/2 100 80 60 40 20 0 10k
100
10
AV = 10 AV = 2 AV = 1
1
0.1
0.01 0.1
1 10 FREQUENCY (MHz)
100
6200 G27
100k
1M 10M FREQUENCY (Hz)
100M
1G
6200 G28
62001fa
13
LT6200/LT6200-5 LT6200-10/LT6201 TYPICAL PERFOR A CE CHARACTERISTICS
Power Supply Rejection Ratio vs Frequency
80
POWER SUPPLY REJECTION RATIO (dB)
70 60
VS = 5V, 0V VCM = VS/2 TA = 25C
OVERSHOOT (%)
50 40 30 20 10 0 1k 10k 100k 1M FREQUENCY (Hz) 10M 100M
6200 G29
25 20 15 10 5 0 10
RS = 20
OVERSHOOT (%)
NEGATIVE SUPPLY
Settling Time vs Output Step (Noninverting)
200
-
SETTLING TIME (ns)
SETTLING TIME (ns)
100 1mV 1mV
100 1mV 1mV
50 10mV 0 -4 -3 -2 1 2 -1 0 OUTPUT STEP (V) 3 4 10mV
50 10mV 0 -4 -3 -2 1 2 -1 0 OUTPUT STEP (V) 3 4 10mV
6200 G32
Distortion vs Frequency, AV = 1
-50
Distortion vs Frequency, AV = 1
-50 AV = 1 VO = 2VP-P -60 VS = 5V -70 HD2, RL = 1k -80 -90 HD3, RL = 1k HD3, RL = 100
-100
DISTORTION (dBc)
AV = 1 VO = 2VP-P -60 VS = 2.5V -70 HD2, RL = 1k -80 HD2, RL = 100 -90 HD3, RL = 100 HD3, RL = 1k DISTORTION (dBc)
DISTORTION (dBc)
HD2, RL = 100
-100 -110 100k
-100 -110 100k
1M FREQUENCY (Hz)
10M
6200 G35
1M FREQUENCY (Hz)
14
+
VIN
+
150
VOUT 500
VIN
150
VOUT
OUTPUT VOLTAGE SWING (VP-P)
-
VS = 5V AV = 1 TA = 25C
UW
POSITIVE SUPPLY
LT6200, LT6201
Overshoot vs Capacitive Load
40 35 30 VS = 5V, 0V AV = 1 RS = 10 60 50
Overshoot vs Capacitive Load
VS = 5V, 0V AV = 2 RS = 10 40 RS = 20 30 20 10 0
RS = 50 RL = 50
RS = 50 RL = 50
100 CAPACITIVE LOAD (pF)
1000
6200 G30
10
100 CAPACITIVE LOAD (pF)
1000
6200 G31
Settling Time vs Output Step (Inverting)
200 VS = 5V AV = -1 TA = 25C
500 500
Maximum Undistorted Output Signal vs Frequency
10 9 8 7 6 5 4 VS = 5V 3 T = 25C A HD2, HD3 < -40dBc 2 100k 1M 10k FREQUENCY (Hz) AV = -1 AV = 2
10M
6200 G34
6200 G33
Distortion vs Frequency, AV = 2
-40 -50 -60 -70 -80 -90 HD2, RL = 100 HD3, RL = 100 HD2, RL = 1k HD3, RL = 1k AV = 2 VO = 2VP-P VS = 2.5V
10M
6200 G36
-110 100k
1M FREQUENCY (Hz)
10M
6200 G37
62001fa
LT6200/LT6200-5 LT6200-10/LT6201 TYPICAL PERFOR A CE CHARACTERISTICS
Distortion vs Frequency, AV = 2
-40 -50 AV = 2 VO = 2VP-P VS = 5V
VOLTAGE GAIN (dB)
DISTORTION (dBc)
-60 -70 -80 -90 HD2, RL = 100 HD2, RL = 1k HD3, RL = 1k
-100 HD3, RL = 100 -110 100k 1M FREQUENCY (Hz) 10M
6200 G38
5V Large-Signal Response
5V 2V/DIV 1V/DIV 0V
0V
VS = 5V, 0V AV = 1 RL = 1k
Output Overdrive Recovery
VIN 1V/DIV VOUT 2V/DIV
0V
0V
VS = 5V, 0V AV = 2
UW
LT6200, LT6201
Channel Separation vs Frequency
0
-10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -110
TA = 25C AV = 1 VS = 5V
-120 0.1
1 10 FREQUENCY (MHz)
100
6200 G77
5V Large-Signal Response
200ns/DIV
6200 G39
VS = 5V AV = 1 RL = 1k
200ns/DIV
6200 G41
5V Small-Signal Response
50mV/DIV
200ns/DIV
6200 G42
VS = 5V, 0V AV = 1 RL = 1k
200ns/DIV
6200 G40
62001fa
15
LT6200/LT6200-5 LT6200-10/LT6201 TYPICAL PERFOR A CE CHARACTERISTICS
Gain Bandwidth and Phase Margin vs Temperature
90 PHASE MARGIN VS = 5V 80 70
GAIN BANDWIDTH (MHz)
VS = 3V, 0V 1000 900 800 700 600 500 -50 -25 0 25 75 50 TEMPERATURE (C) 100 VS = 3V, 0V GAIN BANDWIDTH VS = 5V
300 250 200 150 100 0 -55 -25 0 25 50 75 TEMPERATURE (C) 100 125 VS = 2.5V FALLING VS = 2.5V RISING
50
OVERSHOOT (%)
60
SLEW RATE (V/s)
Power Supply Rejection Ratio vs Frequency
80
POWER SUPPLY REJECTION RATIO (dB)
70 60 50 40 30 20 10 0 1k
POSITIVE SUPPLY NEGATIVE SUPPLY
VS = 5V, 0V TA = 25C VCM = VS /2
OUTPUT IMPEDANCE ()
GAIN (dB)
10k
100k 1M FREQUENCY (Hz)
10M
Open-Loop Gain vs Frequency
100 90 80 70 60 GAIN (dB) 50 40 30 20 10 0 VS = 5V, 0V CL = 5pF RL = 1k 1M VCM = 4.5V GAIN VCM = 0.5V PHASE VCM = 0.5V VCM = 4.5V 120 100 80
GAIN BANDWIDTH (MHz)
60 40 20 0 -20 -40 -60 -80 -100 PHASE (DEG)
70 60 50 1000 GAIN BANDWIDTH 800 600 400 0 2 8 10 6 TOTAL SUPPLY VOLTAGE (V) 4 12
6200 G52
GAIN BANDWIDTH (MHz)
-10 100k
10M 100M FREQUENCY (Hz)
16
UW
6200 G45
6200 G48
LT6200-5
Slew Rate vs Temperature
450 400 350
PHASE MARGIN (DEG)
1000 100 AV = 50 10 1 0.1
Overshoot vs Capacitive Load
60 VS = 5V, 0V AV = 5 RS = 0
AV = -5 RF = RL = 1k RG = 200
VS = 5V RISING
50 40 30 RS = 10 20 RS = 50 10 0 10 100 CAPACITIVE LOAD (pF) 1000
6200 G47
VS = 5V FALLING
RS = 20
125
6200 G46
Output Impedance vs Frequency
VS = 5V, 0V
Open-Loop Gain vs Frequency
100 90 80 70 60 50 40 30 20 10 VCM = 0V 0 CL = 5pF RL = 1k -10 1M 100k VS = 1.5V GAIN VS = 5V PHASE VS = 5V VS = 1.5V 120 100 80 60 40 20 0
PHASE (DEG)
AV = 5
100M
0.01 100k
1M 10M FREQUENCY (Hz)
100M
6200 G49
10M 100M FREQUENCY (Hz)
1G
6200 G50
Gain Bandwidth and Phase Margin vs Supply Voltage
TA = 25C RL = 1k CL = 5pF 90 80 PHASE MARGIN 900 800 700 600 500 400 300 200 100 0
Gain Bandwidth vs Resistor Load
PHASE MARGIN (DEG)
VS = 5V RF = 10k RG = 1k TA = 25C 0 100 200 300 400 500 600 700 800 900 1000 RESISTOR LOAD ()
G200 G53
1G
6200 G51
62001fa
LT6200/LT6200-5 LT6200-10/LT6201 TYPICAL PERFOR A CE CHARACTERISTICS
Common Mode Rejection Ratio vs Frequency
120
COMMON MODE REJECTION RATIO (dB)
VS = 5V, 0V VCM = VS/2
OUTPUT VOLTAGE SWING (VP-P)
100 80 60 40 20 0 10k
DISTORTION (dB)
100k
1M 10M FREQUENCY (Hz)
100M
2nd and 3rd Harmonic Distortion vs Frequency
-40 -50 -60 RL = 100, 2ND -70 -80 -90 -100 -110 10k RL = 1k, 3RD RL = 100, 3RD RL = 1k, 2ND - 5V 2V/DIV 0V AV = 5 VO = 2VP-P VS = 5V 5V
DISTORTION (dB)
100k 1M FREQUENCY (Hz)
5V Small-Signal Response
10nV
50mV/DIV 0V
VS = 5V, 0V 50ns/DIV AV = 5 RL = 1k CL = 10.8pF SCOPE PROBE
UW
1G
6200 G54
6200 G57
LT6200-5
2nd and 3rd Harmonic Distortion vs Frequency
-40 -50 -60 -70 -80 -90 -100 10k AV = 5 VO = 2VP-P VS = 2.5V RL = 100, 3RD RL = 100, 2ND RL = 1k, 2ND RL = 1k, 3RD
Maximum Undistorted Output Signal vs Frequency
10 9 8 7 6 5 4 3 2 VS = 5V 1 AV = 5 TA = 25C 0 100k 10k
1M 10M FREQUENCY (Hz)
100M
6200 G55
100k 1M FREQUENCY (Hz)
10M
6200 G56
5V Large-Signal Response
Output-Overdrive Recovery
VIN 1V/DIV 0V VOUT 2V/DIV 0V
10M
50ns/DIV VS = 5V AV = 5 RL = 1k CL = 10.8pF SCOPE PROBE
6200 G58
50ns/DIV VS = 5V, 0V AV = 5 CL = 10.8pF SCOPE PROBE
6200 G59
Input Referred High Frequency Noise Spectrum
1nV/Hz/DIV
6200 G61
0nV 100kHz
15MHz/DIV
150MHz
6200 G60
NOISE LIMITED BY INSTRUMENT NOISE FLOOR
62001fa
17
LT6200/LT6200-5 LT6200-10/LT6201 TYPICAL PERFOR A CE CHARACTERISTICS
Gain Bandwidth and Phase Margin vs Temperature
80 PHASE MARGIN
GAIN BANDWIDTH (MHz)
VS = 5V VS = 3V, 0V
SLEW RATE (v/s)
OVERSHOOT (%)
2000 1800 1600 1400 1200 1000 -50 -25 0 25 50 75 TEMPERATURE (C) 100 125 VS = 3V, 0V GAIN BANDWIDTH VS = 5V
Power Supply Rejection Ratio vs Frequency
80
POWER SUPPLY REJECTION RATIO (dB)
70 60 50 40 30 20 10 0 1k
POSITIVE SUPPLY NEGATIVE SUPPLY
VS = 5V, 0V TA = 25C VCM = VS /2
OUTPUT IMPEDANCE ()
GAIN (dB)
10k
100k 1M FREQUENCY (Hz)
10M
Open-Loop Gain vs Frequency
100 90 80 70 60 GAIN (dB) 50 40 30 20 10 VS = 5V, 0V 0 CL = 5pF RL = 1k -10 1M 100k GAIN VCM = 4.5V VCM = 0.5V PHASE VCM = 0.5V VCM = 4.5V 120 100 80
GAIN BANDWIDTH (MHz)
60 40 20 0 -20 -40 -60 -80 -100 PHASE (DEG)
PHASE MARGIN
70 60
GAIN BANDWIDTH (MHz)
10M 100M FREQUENCY (Hz)
18
UW
6200 G62
6200 G65
LT6200-10
Slew Rate vs Temperature
750 700 650 600 550 500 450 400 350 300 250 200 150 -50 -25 50 25 0 75 TEMPERATURE (C) 100 125
0
PHASE MARGIN (DEG)
Overshoot vs Capacitive Load
60 VS = 5V, 0V AV = 10 RS = 0 40 RS = 10 30 20 RS = 20 10 RS = 50 10 100 CAPACITIVE LOAD (pF) 1000
6200 G64
70 60 50
AV = -10 RF = RL = 1k RG = 100
VS = 5V RISING
50
VS = 5V FALLING
VS = 2.5V FALLING VS = 2.5V RISING
6200 G63
Output Impedance vs Frequency
1000 VS = 5V, 0V
Open-Loop Gain vs Frequency
100 90 80 70 PHASE VS = 5V VS = 1.5V GAIN VS = 1.5V VS = 5V 120 100 80 60 40 20 0
PHASE (DEG)
100 AV = 100 AV = 10 1
10
60 50 40 30 20
0.1
100M
0.01 100k
1M 10M FREQUENCY (Hz)
100M
6200 G66
10 VCM = 0V 0 CL = 5pF RL = 1k -10 1M 100k
10M 100M FREQUENCY (Hz)
1G
6200 G67
Gain Bandwidth and Phase Margin vs Supply Voltage
TA = 25C RL = 1k CL = 5pF 90 80
PHASE MARGIN (DEG) 1800 1600 1400 1200 1000 800 600 400 200 0
Gain Bandwidth vs Resistor Load
1800 1600 1400 1200 1000 0 2 8 10 6 TOTAL SUPPLY VOLTAGE (V) 4 12
6200 G69
50 GAIN BANDWIDTH
VS = 5V RF = 10k RG = 1k TA = 25C 0 100 200 300 400 500 600 700 800 900 1000 RESISTOR LOAD ()
G200 G70
1G
6200 G68
62001fa
LT6200/LT6200-5 LT6200-10/LT6201 TYPICAL PERFOR A CE CHARACTERISTICS
Common Mode Rejection Ratio vs Frequency
120
COMMON MODE REJECTION RATIO (dB)
VS = 5V, 0V VCM = VS/2
OUTPUT VOLTAGE SWING (VP-P)
100 80 60 40 20 0 10k
DISTORTION (dB)
100k
1M 10M FREQUENCY (Hz)
100M
2nd and 3rd Harmonic Distortion vs Frequency
-40 -50 -60 -70 RL = 1k, 3RD -80 -5V -90 -100 -110 10k RL = 1k, 2ND 100k 1M FREQUENCY (Hz) 10M
6200 G74
AV = 10 VO = 2VP-P VS = 5V RL = 100, 2ND RL = 100, 3RD
DISTORTION (dB)
5V Small-Signal Response
10nV
50mV/DIV 0V
VS = 5V, 0V 50ns/DIV AV = 10 RL = 1k CL = 10.8pF SCOPE PROBE
UW
1G
6200 G71
LT6200-10
2nd and 3rd Harmonic Distortion vs Frequency
-40 -50 -60 -70 -80 -90 RL = 1k, 2ND -100 10k AV = 10 VO = 2VP-P VS = 2.5V
Maximum Undistorted Output Signal vs Frequency
10 9 8 7 6 5 4 3 2 VS = 5V 1 AV = 10 TA = 25C 0 100k 10k
RL = 100, 2ND RL = 100, 3RD
RL = 1k, 3RD
1M 10M FREQUENCY (Hz)
100M
6200 G72
100k 1M FREQUENCY (Hz)
10M
6200 G73
5V Large-Signal Response
5V VIN 1V/DIV 0V 2V/DIV 0V VOUT 2V/DIV 0V
Output-Overdrive Recovery
50ns/DIV VS = 5V AV = 10 RL = 1k CL = 10.8pF SCOPE PROBE
6200 G75
VS = 5V, 0V 50ns/DIV AV = 10 CL = 10.8pF SCOPE PROBE
6200 G76
Input Referred High Frequency Noise Spectrum
1nV/Hz/DIV
6200 G78
0nV 100kHz
15MHz/DIV
150MHz
6200 G77
62001fa
19
LT6200/LT6200-5 LT6200-10/LT6201
APPLICATIO S I FOR ATIO
Amplifier Characteristics Figure 1 shows a simplified schematic of the LT6200 family, which has two input differential amplifiers in parallel that are biased on simultaneously when the common mode voltage is at least 1.5V from either rail. This topology allows the input stage to swing from the positive supply voltage to the negative supply voltage. As the common mode voltage swings beyond VCC - 1.5V, current source I1 saturates and current in Q1/Q4 is zero. Feedback is maintained through the Q2/Q3 differential amplifier, but with an input gm reduction of 1/2. A similar effect occurs with I2 when the common mode voltage swings within 1.5V of the negative rail. The effect of the gm reduction is a shift in the VOS as I1 or I2 saturate. Input bias current normally flows out of the + and - inputs. The magnitude of this current increases when the input common mode voltage is within 1.5V of the negative rail, and only Q1/Q4 are active. The polarity of this current reverses when the input common mode voltage is within 1.5V of the positive rail and only Q2/Q3 are active. The second stage is a folded cascode and current mirror that converts the input stage differential signals to a single ended output. Capacitor C1 reduces the unity cross frequency and improves the frequency stability without degrading the gain bandwidth of the amplifier. The differential drive generator supplies current to the output transistors that swing from rail-to-rail.
R1 I1 R2 BIAS Q11 -V DESD1 +V Q5 DESD2 Q1 D1 D2 Q9 DESD4 -V +V R3 I2 R4 R5 D3 V-
6203/04 F01
+ -
DESD3
Q2
Figure 1. Simplified Schematic
62001fa
20
U
The LT6200-5/LT6200-10 are decompensated op amps for higher gain applications. These amplifiers maintain identical DC specifications with the LT6200, but have a reduced Miller compensation capacitor CM. This results in a significantly higher slew rate and gain bandwidth product. Input Protection There are back-to-back diodes, D1 and D2, across the + and - inputs of these amplifiers to limit the differential input voltage to 0.7V. The inputs of the LT6200 family do not have internal resistors in series with the input transistors. This technique is often used to protect the input devices from overvoltage that causes excessive currents to flow. The addition of these resistors would significantly degrade the low noise voltage of these amplifiers. For instance, a 100 resistor in series with each input would generate 1.8nV/Hz of noise, and the total amplifier noise voltage would rise from 0.95nV/Hz to 2.03nV/Hz. Once the input differential voltage exceeds 0.7V, steady-state current conducted though the protection diodes should be limited to 40mA. This implies 25 of protection resistance per volt of continuous overdrive beyond 0.7V. The input diodes are rugged enough to handle transient currents due to amplifier slew rate overdrive or momentary clipping without these resistors. Figure 2 shows the input and output waveforms of the LT6200 driven into clipping while connected in a gain of
V+ DESD7 VSHDN DESD8 -V Q6 CM Q3 Q4 C1 +V DIFFERENTIAL DRIVE GENERATOR Q7 Q10 -V DESD5 +V Q8 DESD6
W
U
U
LT6200/LT6200-5 LT6200-10/LT6201
APPLICATIO S I FOR ATIO
AV = 1. In this photo, the input signal generator is clipping at 35mA, and the output transistors supply this generator current through the protection diodes.
0V
Figure 2. VS = 2.5V, AV = 1 with Large Overdrive
ESD The LT6200 has reverse-biased ESD protection diodes on all inputs and outputs as shown in Figure 1. If these pins are forced beyond either supply, unlimited current will flow through these diodes. If the current is transient and limited to 30mA or less, no damage to the device will occur. Noise The noise voltage of the LT6200 is equivalent to that of a 56 resistor, and for the lowest possible noise it is desirable to keep the source and feedback resistance at or below this value, i.e., RS + RG//RFB 56. With RS + RG//RFB = 56 the total noise of the amplifier is: en = (0.95nV)2 + (0.95nV)2 = 1.35nV. Below this resistance value, the amplifier dominates the noise, but in the resistance region between 56 and approximately 6k, the noise is dominated by the resistor thermal noise. As the total resistance is further increased, beyond 6k, the noise current multiplied by the total resistance eventually dominates the noise. For a complete discussion of amplifier noise, see the LT1028 data sheet.
U
Power Dissipation The LT6200 combines high speed with large output current in a small package, so there is a need to ensure that the die's junction temperature does not exceed 150C. The LT6200 is housed in a 6-lead TSOT-23 package. The package has the V - supply pin fused to the lead frame to enhance the thermal conductance when connecting to a ground plane or a large metal trace. Metal trace and plated through-holes can be used to spread the heat generated by the device to the backside of the PC board. For example, on a 3/32" FR-4 board with 2oz copper, a total of 270 square millimeters connects to Pin 2 of the LT6200 in an TSOT-23 package will bring the thermal resistance, JA, to about 135C/W. Without extra metal trace beside the power line connecting to the V - pin to provide a heat sink, the thermal resistance will be around 200C/W. More information on thermal resistance with various metal areas connecting to the V - pin is provided in Table 1.
Table 1. LT6200 6-Lead TSOT-23 Package
COPPER AREA TOPSIDE (mm2) 270 100 20 0 BOARD AREA (mm2) 2500 2500 2500 2500 THERMAL RESISTANCE (JUNCTION-TO-AMBIENT) 135C/W 145C/W 160C/W 200C/W
VCC 2.5V VEE -2.5V
W
U
U
Device is mounted on topside.
Junction temperature TJ is calculated from the ambient temperature TA and power dissipation PD as follows: TJ = TA + (PD * JA) The power dissipation in the IC is the function of the supply voltage, output voltage and the load resistance. For a given supply voltage, the worst-case power dissipation PD(MAX) occurs at the maximum quiescent supply current and at the output voltage which is half of either supply voltage (or the maximum swing if it is less than 1/2 the supply voltage). PD(MAX) is given by: PD(MAX) = (VS * IS(MAX)) + (VS/2)2/RL Example: An LT6200 in TSOT-23 mounted on a 2500mm 2 area of PC board without any extra heat spreading plane connected to its V - pin has a thermal resistance of
62001fa
21
LT6200/LT6200-5 LT6200-10/LT6201
APPLICATIO S I FOR ATIO
PD(MAX) = (10 * 23mA) + (2.5)2/50 = 0.23 + 0.125 = 0.355W The maximum ambient temperature that the part is allowed to operate is: TA = TJ - (PD(MAX) * 200C/W) = 150C - (0.355W * 200C/W) = 79C To operate the device at higher ambient temperature, connect more metal area to the V - pin to reduce the thermal resistance of the package as indicated in Table 1. DD Package Heat Sinking The underside of the DD package has exposed metal (4mm2) from the lead frame where the die is attached. This provides for the direct transfer of heat from the die junction to printed circuit board metal to help control the maximum operating junction temperature. The dual-inline pin arrangement allows for extended metal beyond the ends of the package on the topside (component side) of a The LT6200 amplifier family has thermal shutdown to protect the part from excessive junction temperature. The amplifier will shut down to approximately 1.2mA supply current per amplifier if the maximum temperature is exceeded. The LT6200 will remain off until the junction temperature reduces to about 135C, at which point the amplifier will return to normal operation. 200C/W, JA. Operating on 5V supplies driving 50 loads, the worst-case power dissipation is given by:
PACKAGE DESCRIPTIO
DD Package 8-Lead Plastic DFN (3mm x 3mm)
(Reference LTC DWG # 05-08-1698)
R = 0.115 TYP 5 0.675 0.05 0.38 0.10 8
3.5 0.05 1.65 0.05 2.15 0.05 (2 SIDES) PACKAGE OUTLINE 0.28 0.05 0.50 BSC 2.38 0.05 (2 SIDES) RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS PIN 1 TOP MARK
22
U
PCB. Table 2 summarizes the thermal resistance from the die junction-to-ambient that can be obtained using various amounts of topside metal (2oz copper) area. On mulitlayer boards, further reductions can be obtained using additional metal on inner PCB layers connected through vias beneath the package.
Table 2. LT6200 8-Lead DD Package
COPPER AREA TOPSIDE (mm2) 4 16 32 64 130 THERMAL RESISTANCE (JUNCTION-TO-AMBIENT) 160C/W 135C/W 110C/W 95C/W 70C/W
3.00 0.10 (4 SIDES) 1.65 0.10 (2 SIDES)
(DD8) DFN 0203
U
W
U
U
0.200 REF
0.75 0.05
4 0.28 0.05 2.38 0.10 (2 SIDES)
1 0.50 BSC
0.00 - 0.05
BOTTOM VIEW--EXPOSED PAD NOTE: 1. DRAWING TO BE MADE A JEDEC PACKAGE OUTLINE M0-229 VARIATION OF (WEED-1) 2. ALL DIMENSIONS ARE IN MILLIMETERS 3. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE 4. EXPOSED PAD SHALL BE SOLDER PLATED
62001fa
LT6200/LT6200-5 LT6200-10/LT6201
PACKAGE DESCRIPTIO U
S6 Package 6-Lead Plastic TSOT-23
(Reference LTC DWG # 05-08-1636)
0.62 MAX 0.95 REF 2.90 BSC (NOTE 4) 1.22 REF 1.4 MIN 2.80 BSC 1.50 - 1.75 (NOTE 4) PIN ONE ID 0.95 BSC 0.80 - 0.90 0.20 BSC 1.00 MAX DATUM `A' 0.01 - 0.10 0.30 - 0.45 6 PLCS (NOTE 3) 0.09 - 0.20 (NOTE 3) 1.90 BSC
S6 TSOT-23 0302
3.85 MAX 2.62 REF
RECOMMENDED SOLDER PAD LAYOUT PER IPC CALCULATOR
0.30 - 0.50 REF NOTE: 1. DIMENSIONS ARE IN MILLIMETERS 2. DRAWING NOT TO SCALE 3. DIMENSIONS ARE INCLUSIVE OF PLATING
4. DIMENSIONS ARE EXCLUSIVE OF MOLD FLASH AND METAL BURR 5. MOLD FLASH SHALL NOT EXCEED 0.254mm 6. JEDEC PACKAGE REFERENCE IS MO-193
S8 Package 8-Lead Plastic Small Outline (Narrow .150 Inch)
(Reference LTC DWG # 05-08-1610)
.045 .005 .050 BSC
8 .189 - .197 (4.801 - 5.004) NOTE 3 7 6 5
.245 MIN
.160 .005 .228 - .244 (5.791 - 6.197)
.150 - .157 (3.810 - 3.988) NOTE 3
.030 .005 TYP
RECOMMENDED SOLDER PAD LAYOUT .010 - .020 x 45 (0.254 - 0.508) .008 - .010 (0.203 - 0.254) 0- 8 TYP
1
2
3
4
.053 - .069 (1.346 - 1.752)
.004 - .010 (0.101 - 0.254)
.016 - .050 (0.406 - 1.270)
NOTE: 1. DIMENSIONS IN
INCHES (MILLIMETERS) 2. DRAWING NOT TO SCALE 3. THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .006" (0.15mm)
.014 - .019 (0.355 - 0.483) TYP
.050 (1.270) BSC
SO8 0303
62001fa
Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
23
LT6200/LT6200-5 LT6200-10/LT6201
TYPICAL APPLICATIO
Rail-to-Rail High Speed Low Noise Instrumentation Amplifier
150pF
Instrumentation Amplifier Frequency Response
42.3dB 3dB/DIV
10 FREQUENCY (MHz) AV = 130 BW-3dB = 85MHz SLEW RATE = 500V/s CMRR = 55dB at 10MHz
RELATED PARTS
PART NUMBER LT1028 LT1677 LT1722/LT1723/LT1724 LT1806/LT1807 LT6203 DESCRIPTION Single, Ultra Low Noise 50MHz Op Amp Single, Low Noise Rail-to-Rail Amplifier Single/Dual/Quad Low Noise Precision Op Amp Single/Dual, Low Noise 325MHz Rail-to-Rail Amplifier Dual, Low Noise, Low Current Rail-to-Rail Amplifier COMMENTS 1.1nV/Hz 3V Operation, 2.5mA, 4.5nV/Hz, 60V Max V0S 70V/s Slew Rate, 400V Max VOS, 3.8nV/Hz, 3.7mA 2.5V Operation, 550V Max VOS, 3.5nV/Hz 1.9nV/Hz, 3mA Max, 100MHz Gain Bandwidth
62001fa
24
Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900
q
FAX: (408) 434-0507 q www.linear.com
+
-
U
+
LT6200-10 100 1k 604 49.9
-
+
LT6200-10
49.9 VOUT
49.9
604
-
1k AV = 10 100
LT6200-10
AV = 13
6200 TA03
100
6200 TA04
LT/TP 1103 1K REV A * PRINTED IN USA
(c) LINEAR TECHNOLOGY CORPORATION 2002

▲Up To Search▲

Price & Availability of LT6201

	To Download LT6201 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .