View BY229X_499658.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

ADVANCED INFORMATION
ADVANCED INFORMATION
ADVANCED INFORMATION
BY229X SERIES
FAST SWITCHING PLASTIC RECTIFIER
Reverse Voltage - 50 to 600 Volts
ITO-220AC
Forward Current - 8.0 Amperes
FEATURES
Plastic package has Underwriters Laboratory Flammability Classification 94V-0 Glass passivated chip junction Low leakage, high voltage High surge current capability Superfast recovery time, for high efficiency High temperature soldering guaranteed: 250C, 0.25" (6.35mm) from case for 10 seconds
0.405 (10.27) 0.383 (9.72)
0.188 (4.77) 0.172 (4.36) 0.110 (2.80) 0.100 (2.54) 0.140 (3.56) DIA. 0.130 (3.30) 0.131 (3.39) DIA. 0.122 (3.08)
0.600 (15.5) 0.580 (14.5) 0.676 (17.2) 0.646 (16.4)
2
0.350 (8.89) 0.330 (8.38)
PIN 1
0.191 (4.85) 0.171 (4.35) 0.560 (14.22) 0.530 (13.46) 0.060 (1.52) 0.110 (2.80) 0.100 (2.54)
MECHANICAL DATA
Case: JEDEC ITO-220AC fully overmolded plastic body over passivated chip Terminals: Plated lead solderable per MIL-STD-750, Method 2026 Polarity: As marked Mounting Position: Any Weight: 0.064 ounce, 1.81 grams Mounting Torque: 5 in. - lbs. max.
0.037 (0.94) 0.027 (0.69) 0.205 (5.20) 0.195 (4.95)
PIN 1 PIN 2
0.022 (0.55) 0.014 (0.36)
Dimensions in inches and (millimeters)
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25C ambient temperature unless otherwise specified.
SYMBOLS
BY229X -200
BY229X -400
BY229X -600
BY229X -800
UNITS
Maximum recurrent peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward rectified current at TC=100C Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) Maximum instantaneous forward voltage at 20A Maximum DC reverse current at rated DC blocking voltage TJ=25C at TJ=125C
VRRM VRMS VDC I(AV)
200 140 200
400 280 400 8.0
600 420 600
800 560 800
Volts Volts Volts Amps
IFSM VF IR trr Qrr dir/dt RJC RJA TJ, TSTG VISOL
100 1.85 10.0 300 145 700 60 4.8 20 -40 to +150 4500 (NOTE 4) 3500 (NOTE 5) 1500 (NOTE 6)
Amps Volts A ns nC A/s C/W C/W C Volts
Maximum reverse recovery time (NOTE 1) Maximum recovered stored charge (NOTE 2) Maximum slope of reverse recovery current (NOTE 2) Maximum thermal resistance (NOTE 3) Typical thermal resistance, junction to air Operating junction and storage temperature range RMS Isolation voltage from terminals to heatsink with RH 30%
NOTES: (1) Reverse recovery test conditions: IF=1A, VR=30V, di/dt=50A/s, Irr=10% IRM (2) Qrr test conditions: IF=2A, VR=30V, di/dt=20A/s (3) Thermal resistance from junction to case mounted on heatsink with heatsink compound (4) Clip mounting, where lead does not overlap heatsink with 0.110" offset. (5) Clip mounting, where leads do overlap heatsink. (6) Screw mounting, where washer diameter is 4.9 mm (0.19").
10/12/98
RATINGS AND CHARACTERISTIC CURVES BY229X SERIES
FIG. 1 - MAXIMUM FORWARD CURRENT DERATING CURVES FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT
12
AVERAGE FORWARD RECTIFIED CURRENT, AMPERES
150
RESISTIVE OR INDUCTIVE LOAD
10 8 6 4 2 0 0
125
PEAK FORWARD SURGE CURRENT, AMPERES
TL=75C 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method)
100 75 50 25
50
100
150 0 1 10
NUMBER OF CYCLES AT 60 HZ
CASE AMBIENT TEMPERATURE, C
100
FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS
FIG. 4 - TYPICAL REVERSE LEAKAGE CHARACTERISTICS
100
INSTANTANEOUS FORWARD CURRENT, AMPERES
1000
TJ=150C TJ=150C
INSTANTANEOUS REVERSE LEAKAGE CURRENT, MICROAMPERES
10
100
TJ=125C
TJ=25C
1
TJ=100C
10
TJ=100C
TJ=125C
0.1 0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
2.0
INSTANTANEOUS FORWARD VOLTAGE, VOLTS
1
TJ=25C
0.10
FIG. 5 - TYPICAL JUNCTION CAPACITANCE
100
0.01 0 20 40 60 80 100
PERCENT OF RATED PEAK REVERSE VOLTAGE, %
10 1 10
VR / V
Cj / pF
100

▲Up To Search▲

Price & Availability of BY229X

	To Download BY229X Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .