|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
TK15409 75 VIDEO LINE DRIVER FEATURES s Internal Y-C Summing Circuit s Voltage Gain is 6 dB Fixed s Internal 75 Driver s Active High ON/OFF Control s Very Low Standby Current (typ. ISTBY 25 A) s Very Small Output Capacitor Using SAG Function Pin s Very Small Package (SOT23L-8) s Single +5 V Power Supply Operation APPLICATIONS s s s s s s Video Equipment Digital Cameras CCD Cameras TV Monitors Video Tape Recorders LCD Projectors DESCRIPTION Operating from a single +5 V supply, the TK15409 is a video line driver IC that takes standard Y and C analog inputs and provides a composite analog output for driving 150 loads (75 resistor and 75 cable load). Internal summing of the Y and C inputs is performed to produce the composite video output. The luminance (Y) input is clamped at 1.25 V and amplified 6 dB; the chromanance (C) input is biased at 2.0 V and amplified 6 dB. The internal 1.5 k SAG function resistor provides gain compensation for low frequency signals. During standby (Pin 5 grounded), the TK15409 consumes only 127 W of power. Nominal power dissipation (no input) is typically 90 mW. The TK15409M is available in the very small SOT23L-8 surface mount package. Clamp 1.25 V 6 dB Amp TK15409 Y-INPUT C-INPUT N/C 01S VCC GND SAG OUTPUT STANDBY BLOCK DIAGRAM BIAS 2.0 V 6 dB Amp 5 k Clamp 1.25 V ORDERING INFORMATION 1.5 k 6 dB 75 DRIVER 5 k Reference & Standby TK15409M Tape/Reel Code TAPE/REEL CODE TL: Tape Left January 2000 TOKO, Inc. VCC Page 1 TK15409 ABSOLUTE MAXIMUM RATINGS Supply Voltage ........................................................... 6 V Operating Voltage Range .............................. 4.5 to 5.5 V Power Dissipation (Note 1) ................................ 350 mW Input Frequency ............................................... 10.0 MHz Storage Temperature Range ................... -55 to +150 C Operating Temperature Range ...................-25 to +85 C TK15409M ELECTRICAL CHARACTERISTICS Test conditions: VCC = 5.0 V, VIN = 1.0 VP-P, RL = 150 , TA = 25 C unless otherwise specified. SYMBOL ICC ISTBY IOS VTHL VTLH VCMP VBIAS GVA-Y1 GVA-Y2 GVA-C1 GVA-C2 DG DP fr PARAMETER Supply Current Standby Supply Current Standby Terminal Current Threshold Voltage (High to Low) Threshold Voltage (Low to High) Clamp Voltage Bias Voltage Voltage Gain Y ch-1 Voltage Gain Y ch-2 Voltage Gain C ch-1 Voltage Gain C ch-1 Differential Gain Differential Phase Frequency Response TEST CONDITIONS No input Pin 5 Grounded Pin 5 in Standby mode Pin 5 Operating to Standby mode Pin 5 Standby to Operating mode Pin 1 Y signal input terminal Pin 8 C signal input terminal fIN = 1 MHz, Y signal input fIN = 15 kHz, Y signal input fIN = 1 MHz, C signal input fIN = 15 kHz, C signal input Staircase signal input Staircase signal input fin = 1 MHz / 5 MHz MIN TYP 18.0 25.3 25.3 MAX 26.0 50.0 50.0 0.3 VCC UNITS mA A A V V V V dB dB dB dB % deg dB GND 1.8 1.10 1.70 5.2 5.2 5.1 5.1 -3.0 -3.0 1.28 2.00 5.7 5.7 5.6 5.6 -1.2 -0.4 -0.5 1.50 2.30 6.2 6.2 6.1 6.1 +3.0 +3.0 Note 1: Power dissipation is 350 mW in free air. Derate at 2.8 mW/C for operation above 25C. Page 2 January 2000 TOKO, Inc. TK15409 TEST CIRCUIT Y - INPUT 4.7 F + 75 4.7 F + 75 C - INPUT N/C CVBS - OUTPUT VOUT = 2.0 VP-P SAG 75 75 + 33 F GND 33 F + VCC = 5.0 V + 33 F OUTPUT Standby January 2000 TOKO, Inc. Page 3 TK15409 TYPICAL PERFORMANCE CHARACTERISTICS SUPPLY CURRENT VS. SUPPLY VOLTAGE 22 20 18 16 14 12 4.0 ISTBY (A) ICC (mA) STANDBY SUPPLY CURRENT VS. SUPPLY VOLTAGE 50 40 30 20 10 0 4.0 4.5 5.0 VCC (V) 5.5 6.0 4.5 5.0 VCC (V) 5.5 6.0 VS. SUPPLY CLAMP VOLTAGE VOLTAGE 2.10 2.05 VBIAS (V) BIAS VOLTAGE VS. SUPPLY VOLTAGE 1.32 1.30 VCMP (V) 1.28 1.26 1.24 1.22 4.0 2.00 1.95 1.90 1.85 4.0 4.5 5.0 VCC (V) 5.5 6.0 4.5 5.0 VCC (V) 5.5 6.0 VOLTAGE GAIN Y VS. SUPPLY VOLTAGE 6.5 VOLTAGE GAIN C VS. SUPPLY VOLTAGE 6.5 6.0 6.0 GVA-Y (dB) GVA-C (dB) 5.5 5.5 5.0 5.0 4.5 4.0 4.5 5.0 VCC (V) 5.5 6.0 4.5 4.0 4.5 5.0 VCC (V) 5.5 6.0 Page 4 January 2000 TOKO, Inc. TK15409 TYPICAL PERFORMANCE CHARACTERISTICS DIFFERENTIAL GAIN VS. SUPPLY VOLTAGE 0.0 DIFFERENTIAL PHASE VS. SUPPLY VOLTAGE 4.0 -2.0 2.0 DP (deg) DG (%) -4.0 0.0 -6.0 -2.0 -8.0 4.0 4.5 5.0 VCC (V) 5.5 6.0 -4.0 4.0 4.5 5.0 VCC (V) 5.5 6.0 SUPPLY CURRENT VS. TEMPERATURE 22 20 18 16 14 12 -50 50 40 STANDBY SUPPLY CURRENT VS. TEMPERATURE ISTBY (A) 0 TA (C) 50 100 ICC (mA) 30 20 10 0 -50 0 TA (C) 50 100 THRESHOLD VOLTAGE VS. TEMPERATURE 2.5 2.0 1.5 1.0 VTHL CLAMP VOLTAGE VS. TEMPERATURE 1.5 1.4 VCMP (V) VTLH VT (V) 1.3 1.2 0.5 0.0 -50 1.1 -50 0 TA (C) 50 100 0 TA (C) 50 100 January 2000 TOKO, Inc. Page 5 TK15409 TYPICAL PERFORMANCE CHARACTERISTICS BIAS VOLTAGE VS. TEMPERATURE 2.4 6 4 2.2 VBIAS (V) DIFFERENTIAL GAIN VS. TEMPERATURE 2 2.0 DG (%) 0 TA (C) DIFFERENTIAL PHASE VS. TEMPERATURE 0 -2 1.8 -4 1.6 -50 -6 -50 50 100 0 TA (C) 50 100 6 4 2 DP (deg) 0 -2 -4 -6 -50 0 TA (C) 50 100 Page 6 January 2000 TOKO, Inc. TK15409 PIN FUNCTION DESCRIPTION PIN NO. 1 SYMBOL Y-INPUT INTERNAL EQUIVALENT CIRCUIT VCC DESCRIPTION Luminance Input Terminal. The luminance input signal is clamped at 1.25 V. 1.25 V 2 3 4 NC SAG OUTPUT VCC No Connection Terminal Pin 4: Signal Output Terminal. The output is available to drive a 75 + 75 load. 1.5 k Pin 3: SAG Terminal. 5k 5 STANDBY VCC 200 k 5k Standby Logic Terminal. The device is in the standby mode when Pin 5 is connected to Low. The device is in the operation mode when Pin 5 is connected to High or Open. 6 7 8 GND VCC C-INPUT VCC GND Terminal Power Supply Terminal Chromanance Input Terminal. The chromanance input signal is biased to 2.0 V by a 100 k bias resistor. 100 k 2.0 V January 2000 TOKO, Inc. Page 7 TK15409 PACKAGE OUTLINE SOT23L-8 0.45 Marking Information Marking 409 TK15409 8 5 marking 1.0 e 0.8 1 e 0.8 4 +0.15 - 0.05 Recommended Mount Pad 0.1 M 0.3 +0.3 3.5 - 0.1 (3.4) 0.3 2.2 1.4max 1.2 e1 3.0 0 - 0.1 +0.15 - 0.05 0.4 + 0.3 0.15 0.1 3.3 Dimensions are shown in millimeters Tolerance: x.x = 0.2 mm (unless otherwise specified) Toko America, Inc. Headquarters 1250 Feehanville Drive, Mount Prospect, Illinois 60056 Tel: (847) 297-0070 Fax: (847) 699-7864 TOKO AMERICA REGIONAL OFFICES Midwest Regional Office Toko America, Inc. 1250 Feehanville Drive Mount Prospect, IL 60056 Tel: (847) 297-0070 Fax: (847) 699-7864 Western Regional Office Toko America, Inc. 2480 North First Street , Suite 260 San Jose, CA 95131 Tel: (408) 432-8281 Fax: (408) 943-9790 Eastern Regional Office Toko America, Inc. 107 Mill Plain Road Danbury, CT 06811 Tel: (203) 748-6871 Fax: (203) 797-1223 Semiconductor Technical Support Toko Design Center 4755 Forge Road Colorado Springs, CO 80907 Tel: (719) 528-2200 Fax: (719) 528-2375 Visit our Internet site at http://www.tokoam.com The information furnished by TOKO, Inc. is believed to be accurate and reliable. However, TOKO reserves the right to make changes or improvements in the design, specification or manufacture of its products without further notice. TOKO does not assume any liability arising from the application or use of any product or circuit described herein, nor for any infringements of patents or other rights of third parties which may result from the use of its products. No license is granted by implication or otherwise under any patent or patent rights of TOKO, Inc. Page 8 (c) 2000 Toko, Inc. All Rights Reserved IC-xxx-TK15409 0100O0.0K 15 max January 2000 TOKO, Inc. Printed in the USA |
Price & Availability of TK15409MTL |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |