 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| NON-ISOLATED DC/DC CONVERTERS 2.4 V - 5.5 V Input 0.75 V - 3.63 V/10 A Output VRBC-10F2Ax Series * * * * * * * Non-Isolated High Efficiency High Power Density Fixed Frequency (300kHz) OCP/SCP Flexible Output Voltage Sequencing Over Temperature Protection RoHS Compliant * * * * * * * Under-Voltage Lockout (UVLO) Wide Input Range Wide Trim Range Remote On/Off Remote Sense Converter Can Sink and Source Current Active Low/High (option) Description The Bel VRBC-10F2Ax modules are a series of non-isolated dc/dc converters that deliver up to 10 A of output current with full load efficiency of 94% at 3.3 V output. These modules provide precisely regulated voltage programmable via external resistor from 0.75 V to 3.63 V over a wide range of input voltage (2.4 V-5.5 V). These modules have a sequencing feature that enables designers to implement various types of output voltage sequencing when powering multiple voltages on a board. The open-frame construction and small footprint enable designers to develop cost and space-efficient solutions. Standard features include remote On/Off, remote sense, over current protection, short current protection, wide input, and programmable output voltage. Part Selection Output Voltage 0.75 V - 3.63 V 1 Input Voltage 2.4 V - 5.5 V Max. Output Current 10 A Max. Output Power 36.3 W Typical Efficiency 94% Model Number Active Low VRBC-10F2AL Model Number Active High VRBC-10F2A0 Notes: 1. These modules use a buck topology, so the output voltages must be 0.5 V less than the input voltage. 2. Add "G" to the end of the Model Number to indicate Tray Packaging. Absolute Maximum Ratings Parameter Input Voltage (continuous) Output Enable Terminal Voltage Sequencing Voltage 1 Min -0.3 V -0.3 V -0.3 V -40 C -55 C Typ - Max 5.8 V 5.8 V Vin 85 C 125 C Notes Ambient Temperature Storage Temperature Notes: All specifications are typical at 25 C unless otherwise stated. 1. VRBC-10F2Ax series of modules include a sequencing feature that enables users to implement various types of output voltage sequencing in their applications. This is accomplished via an additional sequencing pin. When the sequencing feature is not used, tie the SEQ pin to Vin. Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 * Tel 201-432-0463 * Fax 201-432-9542 * www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 2.4 V - 5.5 V Input 0.75 V - 3.63 V/10 A Output Input Specifications Parameter Input Voltage Input Current (full load) Vo=3.3 V Vo=1.8 V Vo=0.75 V Input Current (no load) Remote Off Input Current Input Reflected Ripple Current (pk-pk) Input Reflected Ripple Current (rms) I t Inrush Current Transient Turn-on Voltage Threshold Turn-off Voltage Threshold 2 Min 2.4 V - Typ 7.0 A 4.04 A 1.89 A 80 mA 15 mA 120 mA 35 mA 2.2 V 2.0 V Max 5.5 V 8.06 A 6.98 A 4.06 A 22 mA 0.2 A s 2 Notes Vo, set Vin-0.5 V Tested with two 100 uF/10 V tantalum input capacitors (P/N: TPSC107K010R0075 AVX) & simulated source impedance of 1 uH, 5 Hz to 20MHz. Note: All specifications are typical at 25 C unless otherwise stated. Output Specifications Parameter Output Voltage Set Point Output Voltage Set Point Load Regulation Line Regulation Regulation Over Temperature (-40 C to +85 C) Output Current Current Limit Threshold Short Circuit Surge Transient Ripple and Noise (pk-pk) Ripple and Noise (rms) Turn on Time Overshoot at Turn on Output Capacitance ESR 1mohm ESR 10mohm Transient Response 50% ~ 100% Max Load Settling Time 100% ~ 50% Max Load Settling Time 50% ~ 100% Max Load Settling Time 100% ~ 50% Max Load Settling Time Min -2%Vo,set -3%Vo,set 0A 15 A 0 uF 0 uF Typ 0.4%Vo,set 0.3%Vo,set 0.5%Vo,set 25 mV 8 mV 4 mS 0%Vo,set 200 mV 25 uS 200 mV 25 uS 120 mV 50 uS 120 mV 50 uS Max 2%Vo,set 3%Vo,set 10 A 30 A 2A s 50 mV 15 mV 8 mS 3%Vo,set 1000 uF 4700 uF di/dt=2.5A/uS; Vin=5V; and with 10uF/16V tantalum capacitor & 1uF/10V ceramic capacitor at the output di/dt=2.5A/uS; Vin=5V; and with two 150uF/10V tantalum capacitors & 1uF/10V ceramic capacitor at the output Tested with 0-20MHz, 10uF/16V tantalum capacitor & 1uF/10V TDK ceramic capacitor at the output 2 Notes Vin=5 V, lo=lomax full load Over all operating input voltages, resistive loads and temperature conditions Io=Io, min to Io, max Vin=Vin, min to Vin, max Tref=Ta, min to Ta, max All All Note: All specifications are typical at nominal input (Vin=5 V), full load at 25 C unless otherwise stated. Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 * Tel 201-432-0463 * Fax 201-432-9542 * www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 2.4 V - 5.5 V Input Parameter Efficiency Vo=3.3 V Vo=1.8 V Vo=0.75 V Switching Frequency Over Temperature Shutdown Output Trim Range (Wide Trim) Remote Sense Compensation MTBF Dimensions Inches (L x W x H) Millimeters (L x W x H) Weight 2.0 x 0.5 x 0.36 50.8 x 12.7 x 9.2 8.3g 91% 86% 77% 250 kHz 0.7525 V 94% 89% 80% 300 kHz 125 C 6,900,000 hours 350 kHz 3.63 V 10% Measured at Vin=5 V, full load (current source) 0.75 V - 3.63 V/10 A Output Min Typ Max Notes General Specifications Total adjustment of trim, setpoint and remote sense combined should not exceed 3.63 V. Vo=0.7525 V when trim pin open Calculated Per Bell Core SR-332 (IO = Nominal; Ta = 25C) Note: All specifications are typical at 25C unless otherwise stated. Control Specifications Parameter Signal Low (Unit Off) Signal High (Unit On) Signal Low (Unit On) Signal High (Unit Off) Sequencing Voltage Sequencing Slew Rate Capability Sequencing Delay Time Tracking Accuracy Power-Up Power-Down 100mV 200mV 200mV 400mV Min -0.3 V 1.5 V -0.3 V 1.5 V 0.05 V 10 mS Typ Max 0.3 V 5.8 V 0.3 V 5.8 V Vin 2 V/mS Delay from Vin, min to application of voltage on SEQ pin Notes VRBC-10F2A0; Remote On/Off pin open, Unit on. VRBC-10F2AL; Remote On/Off pin open, Unit on. Sequencing Voltage applied on SEQ should be higher than output voltage. Output Trim Equations Equation for calculating the trim resistor (in k) given the desired adjusted voltage (Vadj) is shown below. The Trim Up resistor should be connected between the Trim pin and Ground. Vout Rtrim = 21.07 - 5.11 Vadj - 0.7525 Module Trim GND Rtrim Equation for calculating the trim voltage (in V) given the desired adjusted voltage (Vadj) is shown below. The Trim Up voltage should be connected between the Trim pin and Ground. Vrim = 0.7 - 0.1698 x (Vadj - 0.7525) Vout Module Trim Vtrim GND Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 * Tel 201-432-0463 * Fax 201-432-9542 * www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 2.4 V - 5.5 V Input 0.75 V - 3.63 V/10 A Output Efficiency Data 98.0% 96.0% 94.0% 92.0% 90.0% 88.0% 86.0% 84.0% 82.0% 80.0% 1.0 4.5V 5.0V 5.5V 2.5 5.0 7.5 10.0 Vo=3.3 V 100.0% 95.0% 90.0% 85.0% 80.0% 3.0V 5.0V 5.5V 75.0% 70.0% 1.0 2.5 5.0 7.5 10.0 Vo=1.8 V 95.0% 90.0% 85.0% 80.0% 75.0% 70.0% 65.0% 60.0% 1 3 5 8 10 2.4V 5.0V 5.5V Vo=0.75 V Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 * Tel 201-432-0463 * Fax 201-432-9542 * www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 2.4 V - 5.5 V Input 0.75 V - 3.63 V/10 A Output Thermal Derating Curves Vin= 5.0 V, Vo= 3.3 V Vin= 5.0 V, Vo= 1.8 V Vin=5.0 V, Vo=0.75 V Vin=3.3 V, Vo=0.75 V/1.8 V/2.5 V Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 * Tel 201-432-0463 * Fax 201-432-9542 * www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 2.4 V - 5.5 V Input 0.75 V - 3.63 V/10 A Output Ripple and Noise Waveforms Vin=5 V, Vo=0.75 V Vin=5 V, Vo=1.8 V Vin=5 V, Vo=3.3 V Note: Ripple and noise tested at 0-20 MHz BW, 10 uF/16 V tantalum capacitor and 1 uF/10 V ceramic capacitor, full load, and Ta=25 deg C. Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 * Tel 201-432-0463 * Fax 201-432-9542 * www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 2.4 V - 5.5 V Input 0.75 V - 3.63 V/10 A Output Transient Response Waveforms 50% to 100% load step at Vin=5 V, Vo=0.75 V 100% to 50% load step at Vin=5 V, Vo=0.75 V 50% to 100% load step at Vin=5 V, Vo=1.8 V 100% to 50% load step at Vin=5 V, Vo=1.8 V 50% to 100% load step at Vin=5 V, Vo=3.3 V 100% to 50% load step at Vin=5 V, Vo=3.3 V Note: Transient response tested at di/dt=2.5 A/uS, with 10 uF/16 V Tantalum capacitor and 1 uF/10 V ceramic capacitor, and Ta=25 deg C. Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 * Tel 201-432-0463 * Fax 201-432-9542 * www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 2.4 V - 5.5 V Input 0.75 V - 3.63 V/10 A Output Mechanical Outline Pin Connections Pin 1 2 3 4 5 6 7 8 9 10 11 Function Vout Vout Remote Sense Vout Ground Ground Vin Vin SEQ Trim Remote On/Off RoHS Compliance Complies with the European Directive 2002/95/EC, calling for the elimination of lead and other hazardous substances from electronic products. (c)2006 Bel Fuse Inc. Specifications subject to change without notice. 031706 CORPORATE Bel Fuse Inc. 206 Van Vorst Street Jersey City, NJ 07302 Tel 201-432-0463 Fax 201-432-9542 www.belfuse.com FAR EAST Bel Fuse Ltd. 8F/ 8 Luk Hop Street San Po Kong Kowloon, Hong Kong Tel 852-2328-5515 Fax 852-2352-3706 www.belfuse.com EUROPE Bel Fuse Europe Ltd. Preston Technology Management Centre Marsh Lane, Suite G7, Preston Lancashire, PR1 8UD, U.K. Tel 44-1772-556601 Fax 44-1772-888366 www.belfuse.com |
Price & Availability of VRBC-10F2A0
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |