Part Number Hot Search : 
A1201 XSD403 SB10100 5KP60A 8FU60 BAR5006S WA302 MCJ40
Product Description
Full Text Search
 

To Download MC74LVXT805105 Datasheet File

  If you can't view the Datasheet, Please click here to try to view without PDF Reader .  
 
 


  Datasheet File OCR Text:
 MC74LVXT8051 Analog Multiplexer / Demultiplexer
High-Performance Silicon-Gate CMOS
The MC74LVXT8051 utilizes silicon-gate CMOS technology to achieve fast propagation delays, low ON resistances, and low OFF leakage currents. This analog multiplexer/demultiplexer controls analog voltages that may vary across the complete power supply range (from VCC to GND). The LVXT8051 is similar in pinout to the high-speed HC4051A and the metal-gate MC14051B. The Channel-Select inputs determine which one of the Analog Inputs/Outputs is to be connected by means of an analog switch to the Common Output/Input. When the Enable pin is HIGH, all analog switches are turned off. The Channel-Select and Enable inputs are compatible with TTL-type input thresholds. The input protection circuitry on this device allows overvoltage tolerance on the input, allowing the device to be used as a logic-level translator from 3.0 V CMOS logic to 5.0V CMOS Logic or from 1.8V CMOS logic to 3.0 V CMOS Logic while operating at the higher-voltage power supply. The MC74LVXT8051 input structure provides protection when voltages up to 7.0 V are applied, regardless of the supply voltage. This allows the MC74LVXT8051 to be used to interface 5.0 V circuits to 3.0 V circuits. This device has been designed so that the ON resistance (Ron) is more linear over input voltage than Ron of metal-gate CMOS analog switches.
Features http://onsemi.com MARKING DIAGRAMS
16 SOIC-16 D SUFFIX CASE 751B 1 LVXT8051 AWLYWW
16 TSSOP-16 DT SUFFIX CASE 948F 1 LVXT 8051 ALYW
16 SOEIAJ-16 M SUFFIX CASE 966 1 LVXT8051 ALYW
* * * * * * * * *
Fast Switching and Propagation Speeds Low Crosstalk Between Switches Diode Protection on All Inputs/Outputs Analog Power Supply Range (VCC - GND) = 2.0 to 6.0 V Digital (Control) Power Supply Range (VCC - GND) = 2.0 to 6.0 V Improved Linearity and Lower ON Resistance Than Metal-Gate Counterparts Low Noise In Compliance With the Requirements of JEDEC Standard No. 7A Pb-Free Packages are Available*
A WL or L Y WW or W
= = = =
Assembly Location Wafer Lot Year Work Week
ORDERING INFORMATION
See detailed ordering and shipping information in the package dimensions section on page 2 of this data sheet.
*For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D.
(c) Semiconductor Components Industries, LLC, 2005
1
March, 2005 - Rev. 3
Publication Order Number: MC74LVXT8051/D
MC74LVXT8051
FUNCTION TABLE - MC74LVXT8051
Control Inputs VCC 16 X2 15 X1 14 X0 13 X3 12 A 11 B 10 C 9 Enable L L L L L L L L H C L L L L H H H H X Select B A L L H H L L H H X L H L H L H L H X ON Channels X0 X1 X2 X3 X4 X5 X6 X7 NONE
1 X4
2 X6
3 X
4 X7
5 X5
6
7
8 GND
Enable NC
PIN CONNECTION AND MARKING DIAGRAM (Top View)
X = Don't Care
X0 14 X1 15 X2 ANALOG 12 INPUTS/ X3 OUTPUTS X4 1 5 X5 2 X6 4 X7 11 A CHANNEL 10 B SELECT 9 INPUTS C 6 ENABLE
13
3
MULTIPLEXER/ DEMULTIPLEXER
X
COMMON OUTPUT/ INPUT
PIN 16 = VCC PIN 8 = GND
Figure 1. LOGIC DIAGRAM Single-Pole, 8-Position Plus Common Off
ORDERING INFORMATION
Device MC74LVXT8051D MC74LVXT8051DG MC74LVXT8051DR2 MC74LVXT8051DR2G MC74LVXT8051DTR2 MC74LVXT8051M MC74LVXT8051MG MC74LVXT8051MEL MC74LVXT8051MELG Package SOIC-16 SOIC-16 (Pb-Free) SOIC-16 SOIC-16 (Pb-Free) TSSOP-16* SOEIAJ-16 SOEIAJ-16 (Pb-Free) SOEIAJ-16 SOEIAJ-16 (Pb-Free) Shipping 48 Units / Rail 48 Units / Rail 2500 Tape & Reel 2500 Tape & Reel 2500 Tape & Reel 50 Units / Rail 50 Units / Rail 2000 Tape & Reel 2000 Tape & Reel
For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. *This package is inherently Pb-Free.
http://onsemi.com
2
MC74LVXT8051
IIIIIIIIIIIIIIIIIIII I I I IIIIIIIIIIIIIIIIIIIIIII IIII IIIIIIII I I I III I I I I I I IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIII I I IIIIIIIIIIIIIIII III I I I IIIIIIIIIIIIIIIIIIIIIII I I III I I I IIIIIIIIIIIIIIIIIIIIIII I I I IIIIIIIIIIIIIIIIIIIIIII I I I IIIIIIIIIIIIIIIIIIIIIII I I I IIIIIIIIIIIIIIIIIIIIIII I I I IIIIIIIIIIIIIIIIIIIIIII I I I IIIIIIIIIIIIIIIIIIIIIII I I I IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIII I IIII IIIIIIIIIIIIIIIIIIIIIII IIIIII I I IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIII I IIIIIIIIIIIIIIIIIIIIIII
MAXIMUM RATINGS
SymbolIIIIIIIIIIIII Parameter VCC VIS Vin I Positive DC Supply Voltage Analog Input Voltage (Referenced to GND) Value Unit V V V - 0.5 to + 7.0 - 0.5 to VCC + 0.5 - 0.5 to VCC + 0.5 -20 500 450 Digital Input Voltage (Referenced to GND) DC Current, Into or Out of Any Pin Power Dissipation in Still Air, Storage Temperature Range mA PD SOIC Package TSSOP Package mW _C _C Tstg TL - 65 to + 150 260 Lead Temperature, 1 mm from Case for 10 Seconds Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied, damage may occur and reliability may be affected. Derating - SOIC Package: - 7 mW/_C from 65_ to 125_C TSSOP Package: - 6.1 mW/_C from 65_ to 125_C
This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this high-impedance circuit. For proper operation, Vin and Vout should be constrained to the range GND v (Vin or Vout) v VCC. Unused inputs must always be tied to an appropriate logic voltage level (e.g., either GND or V CC ). Unused outputs must be left open.
RECOMMENDED OPERATING CONDITIONS
III I I I I I IIIIIIIIIIIIIIIIIIIII I III IIIIIIIIIIIIIIIIIIIIIII II I I IIIIIIIIIIIIIIIIIIIIIII II I I III I I II I I IIIIIIIIIIIIIIIIIIIIIII II I I IIIIIIIIIIIIIIIIIIIIIII II I IIIIIIIIIIIIIIIIIIIIIII II I I IIIIIIIIIIIIIIIIIIIII II I IIIIIIIIIIIIIIIIIIIIIII II I I IIIIIIIIIIIIIIIIIIIIIII II I I IIIIIIIIIIIIIIIIIIIIIII II I I IIIIIIIIIIIIIIIIIIIIIII II I I IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIII II IIII IIIIIIIIIIIIIIIIIIIII II I IIIIIIIIIIIIIIIIIIIIIII IIIIII II
SymbolIIIIIIIIIIIII Parameter VCC VIS Vin Positive DC Supply Voltage Analog Input Voltage (Referenced to GND) Min 2.0 0.0 Max Unit 6.0III V V V VCC VCC Digital Input Voltage (Referenced to GND) Static or Dynamic Voltage Across Switch GND VIO* TA 1.2III V _C Operating Temperature Range, All Package Types - 55 + 85 tr, tf Input Rise/Fall Time (Channel Select or Enable Inputs) VCC = 3.3 V 0.3 V VCC = 5.0 V 0.5 V ns/V 0 0 100 20 *For voltage drops across switch greater than 1.2 V (switch on), excessive VCC current may be drawn; i.e., the current out of the switch may contain both VCC and switch input components. The reliability of the device will be unaffected unless the Maximum Ratings are exceeded.
DC CHARACTERISTICS - Digital Section (Voltages Referenced to GND)
VCC V 3.0 4.5 5.5 3.0 4.5 5.5 5.5 5.5 Guaranteed Limit -55 to 25C 1.2 2.0 2.0 0.53 0.8 0.8 0.1 4 85C 1.2 2.0 2.0 0.53 0.8 0.8 1.0 40 125C 1.2 2.0 2.0 0.53 0.8 0.8 1.0 160 Unit V
Symbol VIH
Parameter Minimum High-Level Input Voltage, Channel-Select or Enable Inputs Maximum Low-Level Input Voltage, Channel-Select or Enable Inputs Maximum Input Leakage Current, Channel-Select or Enable Inputs Maximum Quiescent Supply Current (per Package)
Condition Ron = Per Spec
VIL
Ron = Per Spec
V
Iin ICC
Vin = VCC or GND Channel Select, Enable and VIS = VCC or GND; VIO = 0 V
mA mA
http://onsemi.com
3
MC74LVXT8051
DC ELECTRICAL CHARACTERISTICS Analog Section
IIIIIIIIIIIIIIIIIIIII II I II I I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIII III I I I I II I II I I I I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIII I II III I II II I II I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII I IIIIIIIIIIIIIIIIIIIII II I II II I II I I I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII II I I I I I I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII II I II III I I I I II I II I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIII II I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIII II I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII II I II I I
Guaranteed Limit v 85_C 45 32 28 35 28 25 20 12 12 Symbol Ron Parameter Test Conditions VCC V 3.0 4.5 5.5 3.0 4.5 5.5 3.0 4.5 5.5 5.5 -55 to 25C 40 30 25 30 25 20 v 125_C 50 37 30 40 35 30 25 15 15 Unit W Maximum "ON" Resistance Vin = VIL or VIH VIS = VCC to GND |IS| v 10.0 mA (Figures 1, 2) Vin = VIL or VIH VIS = VCC or GND (Endpoints) |IS| v 10.0 mA (Figures 1, 2) DRon Maximum Difference in "ON" Resistance Between Any Two Channels in the Same Package Vin = VIL or VIH VIS = 1/2 (VCC - GND) |IS| v 10.0 mA 15 8.0 8.0 W Ioff Maximum Off-Channel Leakage Current, Any One Channel Maximum Off-Channel Leakage Current, Common Channel Maximum On-Channel Leakage Current, Channel-to-Channel Vin = VIL or VIH; VIO = VCC or GND; Switch Off (Figure 3) Vin = VIL or VIH; VIO = VCC or GND; Switch Off (Figure 4) 0.1 0.5 1.0 mA 5.5 0.2 2.0 4.0 Ion Vin = VIL or VIH; Switch-to-Switch = VCC or GND; (Figure 5) 5.5 0.2 2.0 4.0 mA
AC CHARACTERISTICS (CL = 50 pF, Input tr = tf = 3 ns)
Symbol tPLH, tPHL Parameter Maximum Propagation Delay, Channel-Select to Analog Output (Figure 9) VCC V 2.0 3.0 4.5 5.5 2.0 3.0 4.5 5.5 2.0 3.0 4.5 5.5 2.0 3.0 4.5 5.5 Guaranteed Limit -55 to 25C 30 20 15 15 4.0 3.0 1.0 1.0 30 20 15 15 20 12 8.0 8.0 10 35 130 1.0 85C 35 25 18 18 6.0 5.0 2.0 2.0 35 25 18 18 25 14 10 10 10 35 130 1.0 125C 40 30 22 20 8.0 6.0 2.0 2.0 40 30 22 20 30 15 12 12 10 35 130 1.0 Unit ns
tPLH, tPHL
Maximum Propagation Delay, Analog Input to Analog Output (Figure 10)
ns
tPLZ, tPHZ
Maximum Propagation Delay, Enable to Analog Output (Figure 11)
ns
tPZL, tPZH
Maximum Propagation Delay, Enable to Analog Output (Figure 11)
ns
Cin CI/O
Maximum Input Capacitance, Channel-Select or Enable Inputs Maximum Capacitance (All Switches Off) Analog I/O Common O/I Feedthrough
pF pF
Typical @ 25C, VCC = 5.0 V CPD Power Dissipation Capacitance (Figure 13)*
2f
45 + ICC VCC .
pF
* Used to determine the no-load dynamic power consumption: P D = CPD VCC
http://onsemi.com
4
MC74LVXT8051
ADDITIONAL APPLICATION CHARACTERISTICS (GND = 0 V)
VCC V Limit* 25C Unit MHz 3.0 4.5 5.5 3.0 4.5 5.5 3.0 4.5 5.5 3.0 4.5 5.5 3.0 4.5 5.5 3.0 4.5 5.5 3.0 4.5 5.5 80 80 80 -50 -50 -50 -37 -37 -37 25 105 135 35 145 190 -50 -50 -50 -60 -60 -60 % 3.0 4.5 5.5 0.10 0.08 0.05 dB mVPP dB
Symbol BW
Parameter Maximum On-Channel Bandwidth or Minimum F Mi i Frequency R Response (Figure 6)
Condition fin = 1MHz Sine Wave; Adjust fin Voltage to Obtain 0dBm t 0dB at VOS; I Increase fin Frequency Until dB Meter F U til Mt Reads -3dB; RL = 50W, CL = 10pF fin = Sine Wave; Adjust fin Voltage to Obtain 0dBm at VIS fin = 10kHz, RL = 600W, CL = 50pF
-
Off-Channel Feedthrough Isolation (Figure 7)
fin = 1.0MHz, RL = 50W, CL = 10pF - Feedthrough Noise. Channel-Select Input to Common I/O (Figure 8) Vin 1MHz Square Wave (tr = tf = 3ns); Adjust RL at Setup so that IS = 0A; Enable = GND RL = 600W, CL = 50pF
RL = 10kW, CL = 10pF - Crosstalk Between Any Two Switches (Figure 12) fin = Sine Wave; Adjust fin Voltage to Obtain 0dBm at VIS fin = 10kHz, RL = 600W, CL = 50pF
fin = 1.0MHz, RL = 50W, CL = 10pF THD Total Harmonic Distortion (Figure 14) fin = 1kHz, RL = 10kW, CL = 50pF THD = THDmeasured - THDsource VIS = 2.0VPP sine wave VIS = 4.0VPP sine wave VIS = 5.0VPP sine wave
*Limits not tested. Determined by design and verified by qualification.
http://onsemi.com
5
MC74LVXT8051
40 Ron , ON RESISTANCE (OHMS) 35 30 25 20 15 10 5 00 1.0 2.0 VIN, INPUT VOLTAGE (VOLTS) 3.0 4.0 125C 85C 25C -55 C
Figure 1a. Typical On Resistance, VCC = 3.0 V
30 Ron , ON RESISTANCE (OHMS) Ron , ON RESISTANCE (OHMS) 25 20 15 10 5 0 125C 85C 25C -55 C
25 125C 85C 25C -55 C
20
15
10
5 0
0
1.0
2.0
3.0
4.0
5.0
0
1.0
2.0
3.0
4.0
5.0
6.0
VIN, INPUT VOLTAGE (VOLTS)
VIN, INPUT VOLTAGE (VOLTS)
Figure 1b. Typical On Resistance, VCC = 4.5 V
Figure 1c. Typical On Resistance, VCC = 5.5 V
PLOTTER
PROGRAMMABLE POWER SUPPLY - +
MINI COMPUTER
DC ANALYZER
VCC DEVICE UNDER TEST
ANALOG IN
COMMON OUT
GND
GND
Figure 2. On Resistance Test Set-Up
http://onsemi.com
6
MC74LVXT8051
VCC VCC
GND OFF VCC A NC OFF
16
VCC
GND VCC
ANALOG I/O
16 OFF OFF
VCC
COMMON O/I
COMMON O/I
VIH
6 8
VIH
6 8
Figure 3. Maximum Off Channel Leakage Current, Any One Channel, Test Set-Up
Figure 4. Maximum Off Channel Leakage Current, Common Channel, Test Set-Up
VCC A ON GND VCC ANALOG I/O VIL 6 8 OFF
16
VCC fin COMMON O/I N/C
VCC 0.1mF ON 16
VOS dB METER CL* RL
6 8 *Includes all probe and jig capacitance
Figure 5. Maximum On Channel Leakage Current, Channel to Channel, Test Set-Up
Figure 6. Maximum On Channel Bandwidth, Test Set-Up
VIS 0.1mF fin RL OFF
VCC 16
VOS dB METER CL* RL RL ON/OFF ANALOG I/O OFF/ON RL
VCC 16 COMMON O/I RL CL* TEST POINT
6 8 VIL or VIH CHANNEL SELECT *Includes all probe and jig capacitance VIH VIL Vin 1 MHz tr = tf = 3 ns
6 8 11
VCC
CHANNEL SELECT *Includes all probe and jig capacitance
Figure 7. Off Channel Feedthrough Isolation, Test Set-Up
Figure 8. Feedthrough Noise, Channel Select to Common Out, Test Set-Up
http://onsemi.com
7
MC74LVXT8051
VCC VCC CHANNEL SELECT tPLH ANALOG OUT 50% 50% GND tPHL 6 8 CHANNEL SELECT *Includes all probe and jig capacitance ANALOG I/O OFF/ON CL* ON/OFF VCC 16 COMMON O/I TEST POINT
Figure 9a. Propagation Delays, Channel Select to Analog Out
Figure 9b. Propagation Delay, Test Set-Up Channel Select to Analog Out
VCC 16 ANALOG IN tPLH ANALOG OUT 50% VCC 50% GND tPHL 6 8 ANALOG I/O ON CL* COMMON O/I TEST POINT
*Includes all probe and jig capacitance
Figure 10a. Propagation Delays, Analog In to Analog Out
Figure 10b. Propagation Delay, Test Set-Up Analog In to Analog Out
tf ENABLE tPZL ANALOG OUT 50%
tr 90% 50% 10% tPLZ VCC GND HIGH IMPEDANCE 10% tPZH tPHZ 90% 50% HIGH IMPEDANCE VOH VOL VIH VIL VCC 1 2 1 2
POSITION 1 WHEN TESTING tPHZ AND tPZH POSITION 2 WHEN TESTING tPLZ AND tPZL VCC 16 ANALOG I/O ON/OFF CL* ENABLE
1kW TEST POINT
6 8
ANALOG OUT
Figure 11a. Propagation Delays, Enable to Analog Out
Figure 11b. Propagation Delay, Test Set-Up Enable to Analog Out
http://onsemi.com
8
MC74LVXT8051
VCC VIS VCC fin 0.1mF OFF RL 6 8 *Includes all probe and jig capacitance RL CL* RL CL* 6 8 11 VCC RL ON 16 VOS ANALOG I/O OFF/ON ON/OFF 16 COMMON O/I NC A
CHANNEL SELECT
Figure 12. Crosstalk Between Any Two Switches, Test Set-Up
0 VCC 16 ON RL CL* VOS TO DISTORTION METER dB -10 -20 -30 -40 -50 -60 6 8 *Includes all probe and jig capacitance -70 -80 -90 - 100
Figure 13. Power Dissipation Capacitance, Test Set-Up
VIS 0.1mF fin
FUNDAMENTAL FREQUENCY
DEVICE SOURCE
1.0
2.0 FREQUENCY (kHz)
3.125
Figure 14a. Total Harmonic Distortion, Test Set-Up
Figure 14b. Plot, Harmonic Distortion
APPLICATIONS INFORMATION The Channel Select and Enable control pins should be at VCC or GND logic levels. VCC being recognized as a logic high and GND being recognized as a logic low. In this example: VCC = +5V = logic high GND = 0V = logic low The maximum analog voltage swing is determined by the supply voltage VCC. The positive peak analog voltage should not exceed VCC. Similarly, the negative peak analog voltage should not go below GND. In this example, the difference between VCC and GND is five volts. Therefore, using the configuration of Figure 15, a maximum analog signal of five volts peak-to-peak can be controlled. Unused analog inputs/outputs may be left floating (i.e., not connected). However, tying unused analog inputs and outputs to VCC or GND through a low value resistor helps minimize crosstalk and feedthrough noise that may be picked up by an unused switch. Although used here, balanced supplies are not a requirement. The only constraints on the power supplies are that: VCC - GND = 2 to 6 volts When voltage transients above VCC and/or below GND are anticipated on the analog channels, external Germanium or Schottky diodes (Dx) are recommended as shown in Figure 16. These diodes should be able to absorb the maximum anticipated current surges during clipping.
http://onsemi.com
9
MC74LVXT8051
+5V +5V 0V ANALOG SIGNAL 16 ON ANALOG SIGNAL +5V 0V VCC Dx Dx GND 6 8 11 10 9 TO EXTERNAL LSTTL COMPATIBLE CIRCUITRY 0 to VIH DIGITAL SIGNALS VCC 16 ON/OFF Dx GND VCC Dx
8
Figure 15. Application Example
Figure 16. External Germanium or Schottky Clipping Diodes
+3V +3V GND ANALOG SIGNAL 16 ON/OFF ANALOG SIGNAL +3V GND +5V GND ANALOG SIGNAL 16 ON/OFF
+5V ANALOG SIGNAL +5V GND +5V
6 8
11 10 9
1.8V - 2.5V CIRCUITRY
6 8
11 10 9
1.8V - 2.5V CIRCUITRY
MC74VHCT1GT50 BUFFERS VCC = 3.0V
a. Low Voltage Logic Level Shifting Control
b. 2-Stage Logic Level Shifting Control
Figure 17. Interfacing to Low Voltage CMOS Outputs
A
11
LEVEL SHIFTER
13
X0
14
X1
B
10
LEVEL SHIFTER
15
X2
12
X3
C
9
LEVEL SHIFTER
1
X4
5
X5
ENABLE
6
LEVEL SHIFTER
2
X6
4
X7
Figure 18. Function Diagram, LVXT8051 http://onsemi.com
10
3
X
MC74LVXT8051
PACKAGE DIMENSIONS
SOIC-16 D SUFFIX CASE 751B-05 ISSUE J
-A-
16 9 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. DIM A B C D F G J K M P R MILLIMETERS MIN MAX 9.80 10.00 3.80 4.00 1.35 1.75 0.35 0.49 0.40 1.25 1.27 BSC 0.19 0.25 0.10 0.25 0_ 7_ 5.80 6.20 0.25 0.50 INCHES MIN MAX 0.386 0.393 0.150 0.157 0.054 0.068 0.014 0.019 0.016 0.049 0.050 BSC 0.008 0.009 0.004 0.009 0_ 7_ 0.229 0.244 0.010 0.019
-B-
1 8
P
8 PL
0.25 (0.010)
M
B
S
G F
K C -T-
SEATING PLANE
R
X 45 _
M D
16 PL M
J
0.25 (0.010)
TB
S
A
S
TSSOP-16 DT SUFFIX CASE 948F-01 ISSUE A
16X K REF NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A DOES NOT INCLUDE MOLD FLASH. PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 5. DIMENSION K DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE K DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 7. DIMENSION A AND B ARE TO BE DETERMINED AT DATUM PLANE -W-. MILLIMETERS MIN MAX 4.90 5.10 4.30 4.50 --- 1.20 0.05 0.15 0.50 0.75 0.65 BSC 0.18 0.28 0.09 0.20 0.09 0.16 0.19 0.30 0.19 0.25 6.40 BSC 0_ 8_ INCHES MIN MAX 0.193 0.200 0.169 0.177 --- 0.047 0.002 0.006 0.020 0.030 0.026 BSC 0.007 0.011 0.004 0.008 0.004 0.006 0.007 0.012 0.007 0.010 0.252 BSC 0_ 8_
0.10 (0.004) 0.15 (0.006) T U
S
M
TU
S
V
S
K K1
16
2X
L/2
9
J1 B -U-
L
PIN 1 IDENT. 1 8
J
N 0.25 (0.010) 0.15 (0.006) T U
S
A -V- N F DETAIL E
C 0.10 (0.004) -T- SEATING
PLANE
H D G
DETAIL E
http://onsemi.com
11
EEE CCC EEE CCC
M
SECTION N-N
-W-
DIM A B C D F G H J J1 K K1 L M
MC74LVXT8051
SOEIAJ-16 M SUFFIX CASE 966-01 ISSUE O
16
9
LE Q1 E HE M_ L DETAIL P
1
8
Z D e A VIEW P
c
NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS D AND E DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS AND ARE MEASURED AT THE PARTING LINE. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 5. THE LEAD WIDTH DIMENSION (b) DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE LEAD WIDTH DIMENSION AT MAXIMUM MATERIAL CONDITION. DAMBAR CANNOT BE LOCATED ON THE LOWER RADIUS OR THE FOOT. MINIMUM SPACE BETWEEN PROTRUSIONS AND ADJACENT LEAD TO BE 0.46 ( 0.018). DIM A A1 b c D E e HE L LE M Q1 Z MILLIMETERS MIN MAX --- 2.05 0.05 0.20 0.35 0.50 0.18 0.27 9.90 10.50 5.10 5.45 1.27 BSC 7.40 8.20 0.50 0.85 1.10 1.50 10 _ 0_ 0.70 0.90 --- 0.78 INCHES MIN MAX --- 0.081 0.002 0.008 0.014 0.020 0.007 0.011 0.390 0.413 0.201 0.215 0.050 BSC 0.291 0.323 0.020 0.033 0.043 0.059 10 _ 0_ 0.028 0.035 --- 0.031
b 0.13 (0.005)
M
A1 0.10 (0.004)
ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 61312, Phoenix, Arizona 85082-1312 USA Phone: 480-829-7710 or 800-344-3860 Toll Free USA/Canada Fax: 480-829-7709 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Japan: ON Semiconductor, Japan Customer Focus Center 2-9-1 Kamimeguro, Meguro-ku, Tokyo, Japan 153-0051 Phone: 81-3-5773-3850 ON Semiconductor Website: http://onsemi.com Order Literature: http://www.onsemi.com/litorder For additional information, please contact your local Sales Representative.
http://onsemi.com
12
MC74LVXT8051/D


▲Up To Search▲   

 
Price & Availability of MC74LVXT805105

All Rights Reserved © IC-ON-LINE 2003 - 2022  

[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy]
Mirror Sites :  [www.datasheet.hk]   [www.maxim4u.com]  [www.ic-on-line.cn] [www.ic-on-line.com] [www.ic-on-line.net] [www.alldatasheet.com.cn] [www.gdcy.com]  [www.gdcy.net]


 . . . . .
  We use cookies to deliver the best possible web experience and assist with our advertising efforts. By continuing to use this site, you consent to the use of cookies. For more information on cookies, please take a look at our Privacy Policy. X