View NCP565D2T_756989.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

NCP565 1.5 A Low Dropout Linear Regulator
The NCP565 low dropout linear regulator will provide 1.5 A at a fixed output voltage or an adjustable voltage down to 0.9 V. The fast loop response and low dropout voltage make this regulator ideal for applications where low voltage and good load transient response are important. Device protection includes current limit, short circuit protection, and thermal shutdown. The NCP565 is packaged in a 5 pin D2PAK for adjustable voltage version and a 3 pin D2PAK for fixed voltage version.
Features http://onsemi.com MARKING DIAGRAMS
* * * * * * * * * * * * * *
Pb-Free Packages are Available Ultra Fast Transient Response (t1.0 ms) Low Ground Current (1.1 mA @ Iload = 1.5 A) Low Dropout Voltage (0.9 V @ Iload = 1.5 A) Low Noise (28 mVrms) 0.9 V Reference Voltage Adjustable Output Voltage from 7.7 V down to 0.9 V 1.2 V Fixed Output Version. Other Fixed Voltages Available on Request Current Limit Protection (3.5 A) Thermal Shutdown Protection (155C)
1 2 3
D2PAK CASE 936 FIXED Tab = Ground Pin 1. Vin 2. Ground 3. Vout
NC P565D2Txx AWLYWWG
1 5
D2PAK CASE 936A ADJUSTABLE Tab = Ground Pin 1. N.C. 2. Vin 3. Ground 4. Vout 5. Adj xx A WL Y WW G
NC P565D2Txx AWLYWWG
Typical Applications
Servers ASIC Power Supplies Post Regulation for Power Supplies Constant Current Source
= R4 or 12 = Assembly Location = Wafer Lot = Year = Work Week = Pb-Free
ORDERING INFORMATION
See detailed ordering and shipping information in the package dimensions section on page 3 of this data sheet.
(c) Semiconductor Components Industries, LLC, 2004
1
July, 2004 - Rev. 8
Publication Order Number: NCP565/D
NCP565
PIN DESCRIPTION
Pin No. Adjustable Version 1 2 Pin No. Fixed Version - 1 Symbol N.C. Vin - Description
AAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA AAAAAAAAAAAA A
Positive Power Supply Input Voltage Power Supply Ground 3, Tab 4 5 2, Tab 3 Ground Vout Adj Regulated Output Voltage - This pin is to be connected to the Rsense resistors on the output. The linear regulator will attempt to maintain 0.9 V between this pin and ground. Refer to Figure 1 for the equation.
MAXIMUM RATINGS
Rating Input Voltage (Note 1) Output Pin Voltage Adjust Pin Voltage Thermal Characteristics (Note 2) Case 936A Thermal Resistance, Junction-to-Air Thermal Resistance, Junction-to-Case Operating Junction Temperature Range Storage Temperature Range
Symbol Vin Vout Vadj
Value 9.0 -0.3 to Vin + 0.3 -0.3 to Vin + 0.3
Unit V V V C/W
RqJA RqJC TJ Tstg
45 5.0 -40 to 150 -55 to 150 C C
Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied, damage may occur and reliability may be affected. 1. This device series contains ESD protection and exceeds the following tests: Human Body Model JESD 22-A114-B Machine Model JESD 22-A115-A 2. The maximum package power dissipation is: TJ(max) * TA PD + RqJA
Vin
Vin
C1
Voltage Reference Block
C1 Vref = 0.9 V Output Stage Vout 5.6 pF ADJ GND R2
Voltage Reference Block
Vref = 0.9 V Output Stage R1 Vout
R1 C2
C2 R2
R1 + R2
Vout *1 Vref
GND
GND
Figure 1. Typical Schematic, Adjustable Output
Figure 2. Typical Schematic, Fixed Output
http://onsemi.com
2
NCP565
ELECTRICAL CHARACTERISTICS (Vin - Vout = 1.6 V, Vout = 0.9 V, TJ = 25C, Cin = Cout = 150 mF, values unless otherwise noted.)
Characteristic ADJUSTABLE OUTPUT VERSION Reference Voltage (10 mA < Iout < 1.5 A; 2.5 V < Vin < 9.0 V; TJ = -10 to 105C) Reference Voltage (10 mA < Iout < 1.5 A; 2.5 V < Vin < 9.0 V; TJ = -40 to 125C) ADJ Pin Current Line Regulation (Iout = 10 mA) Load Regulation (10 mA < Iout < 1.5 A) Dropout Voltage (Iout = 1.5 A) (Note 3) Current Limit Ripple Rejection (120 Hz; Iout = 1.5 A) Ripple Rejection (1 kHz; Iout = 1.5 A) Thermal Shutdown Ground Current (Iout = 1.5 A) Output Noise Voltage (f = 100 Hz to 100 kHz, Iout = 1.5 A) FIXED OUTPUT VOLTAGE Output Voltage (10 mA < Iout < 1.5 A; 2.5 V < Vin < 9.0 V; TJ = -10 to 105C) Output Voltage (10 mA < Iout < 1.5 A; 2.5 V < Vin < 9.0 V; TJ = -40 to 125C) Line Regulation (Iout = 10 mA) Load Regulation (10 mA < Iout < 1.5 A) Dropout Voltage (Iout = 1.5 A) (Note 3) Current Limit Ripple Rejection (120 Hz; Iout = 1.5 A) Ripple Rejection (1 kHz; Iout = 1.5 A) Thermal Shutdown Ground Current (Iout = 1.5 A) Output Noise Voltage (f = 100 Hz to 100 kHz, Iout = 1.5 A) 3. Dropout voltage is a measurement of the minimum input/output differential at full load. Iq Vn Vout Vout Regline Regload Vdo Ilim RR RR 1.176 (-2%) 1.164 (-3%) - - - 1.6 - - - - - 1.2 1.2 0.03 0.03 0.9 3.5 85 75 150 1.1 28 1.224 (+2%) 1.236 (+3%) - - 1.3 - - - - 3.0 - % % % % V A dB dB C mA mVrms Iq Vn Vref Vout IAdj Regline Regload Vdo Ilim RR RR 0.882 (-2%) 0.873 (-3%) - - - - 1.6 - - - - - 0.9 0.9 30 0.03 0.03 0.9 3.5 85 75 150 1.1 28 0.918 (+2%) 0.927 (+3%) - - - 1.3 - - - - 3.0 - V V nA % % V A dB dB C mA mVrms Symbol Min Typ Max Unit
ORDERING INFORMATION
Device NCP565D2T NCP565D2TR4 NCP565D2TR4G NCP565D2T12 NCP565D2T12R4 NCP565D2T12R4G Nominal Output Voltage* Adj Adj Adj Fixed Fixed Fixed Package D2PAK D2PAK D2PAK (Pb-Free) D2PAK D2PAK D2PAK (Pb-Free) Shipping 50 Tube 800 Tape & Reel 800 Tape & Reel 50 Tube 800 Tape & Reel 800 Tape & Reel
*For other fixed output versions, please contact the factory. For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D.
http://onsemi.com
3
NCP565
TYPICAL CHARACTERISTICS
ISC, SHORT CIRCUIT CURRENT LIMIT (A)
0.9005 Vref, REFERENCE VOLTAGE (V) 0.9000 0.8995 0.8990 0.8985 0.8980 0.8975 0.8970 -50 Vin = 2.5 V Vout = 0.9 V Cin = Cout = 150 mF -25 0 25 50 75 100 125 150
3.90 3.85 3.80 3.75 3.70 3.65 3.60 3.55 3.50 3.45 3.40 3.35 -50 -25 0 25 50 75 100 125 150 Vin = 2.5 V Vout = 0.9 V Cin = Cout = 150 mF
TJ, JUNCTION TEMPERATURE (C)
TJ, JUNCTION TEMPERATURE (C)
Figure 3. Output Voltage vs. Temperature
Figure 4. Short Circuit Current Limit vs. Temperature
1.16 IGND, GROUND CURRENT (mA) 1.14 1.12 1.10 1.08 1.06 1.04 1.02 1.00 0.98 0.96 -50 -25 0 25 50 75 100 125 150 Vin = 2.5 V Vout = 0.9 V Iout = 1.5 V Cin = Cout = 150 mF
1.2 Vin - Vout, DROPOUT VOLTAGE (V) 1.0 0.8 0.6 0.4 Cin = Cout = 150 mF 0.2 0 -50 Iout = 50 mA
Iout = 1.5 A
-25
0
25
50
75
100
125
150
TJ, JUNCTION TEMPERATURE (C)
TJ, JUNCTION TEMPERATURE (C)
Figure 5. Dropout Voltage vs. Temperature
1.28 IGND, GROUND CURRENT (mA) 1.26 RIPPLE REJECTION (dB) 1.24 1.22 1.2 1.18 1.16 1.14 1.12 0 300 600 900 1200 1500 Iout, OUTPUT CURRENT (mA) 100 90 80 70 60 50 40 30 20 10 0 10
Figure 6. Ground Current vs. Temperature
Iout = 1.5 A
100
1000
10000
100000 1000000
F, FREQUENCY (Hz)
Figure 7. Ground Current vs. Output Current
Figure 8. Ripple Rejection vs. Frequency
http://onsemi.com
4
NCP565
TYPICAL CHARACTERISTICS
OUTPUT VOLTAGE DEVIATION (mV) OUTPUT VOLTAGE DEVIATION (mV) 10 0 -10 -20 -30 -40 Vin = 4.59 V Vout = 0.9 V 10 0 -10 -20 -30 -40 Vin = 4.59 V Vout = 0.9 V
Iout, OUTPUT CURRENT (A)
1.50 1.00 0.50 0 0 50 100 150 200 250 300 350 400
Iout, OUTPUT CURRENT (A)
1.50 1.00 0.50 0 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0
TIME (nS)
TIME (ms)
Figure 9. Load Transient from 10 mA to 1.5 A
Figure 10. Load Transient from 10 mA to 1.5 A
OUTPUT VOLTAGE DEVIATION (mV)
40 30 20 10 0 1.50 1.00 0.50 0 -50 0 50 100 150 200 250 300 350 400 Vin = 4.59 V Vout = 0.9 V
OUTPUT VOLTAGE DEVIATION (mV)
50
50 40 30 20 10 0 Vin = 4.59 V Vout = 0.9 V
Iout, OUTPUT CURRENT (A)
Iout, OUTPUT CURRENT (A)
1.50 1.00 0.50 0 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6
TIME (nS)
TIME (ms)
Figure 11. Load Transient from 1.5 A to 10 mA
100 90 NOISE DENSITY (nVrms/ Hz) 80 70 60 50 40 30 20 10 0 Start 1.0 kHz FREQUENCY (kHz) Stop 100 kHz Vin = 3.0 V Vout = 0.9 V Iout = 10 mA NOISE DENSITY (nVrms/ Hz) 100 90 80 70 60 50 40 30 20 10
Figure 12. Load Transient from 1.5 A to 10 mA
Vin = 3.0 V Vout = 0.9 V Iout = 1.5 A
0 Start 1.0 kHz FREQUENCY (kHz)
Stop 100 kHz
Figure 13. Noise Density vs. Frequency
Figure 14. Noise Density vs. Frequency
http://onsemi.com
5
NCP565
APPLICATION INFORMATION The NCP565 low dropout linear regulator provides adjustable voltages at currents up to 1.5 A. It features ultra fast transient response and low dropout voltage. These devices contain output current limiting, short circuit protection and thermal shutdown protection.
Input, Output Capacitor and Stability Adjustable Operation
An input bypass capacitor is recommended to improve transient response or if the regulator is located more than a few inches from the power source. This will reduce the circuit's sensitivity to the input line impedance at high frequencies and significantly enhance the output transient response. Different types and different sizes of input capacitors can be chosen dependent on the quality of power supply. A 150 mF OSCON 16SA150M type from Sanyo should be adequate for most applications. The bypass capacitor should be mounted with shortest possible lead or track length directly across the regulator's input terminals. The output capacitor is required for stability. The NCP565 remains stable with ceramic, tantalum, and aluminum- electrolytic capacitors with a minimum value of 1.0 mF as long as the ESR remains between 50 mW and 2.5 W. The NCP565 is optimized for use with a 150 mF OSCON 16SA150M type in parallel with a 10 mF OSCON 10SL10M type from Sanyo. The 10 mF capacitor is used for best AC stability while 150 mF capacitor is used for achieving excellent output transient response. The output capacitors should be placed as close as possible to the output pin of the device. If not, the excellent load transient response of NCP565 will be degraded.
GEN
The typical application circuit for the adjustable output regulators is shown in Figure 1. The adjustable device develops and maintains the nominal 0.9 V reference voltage between Adj and ground pins. A resistor divider network R1 and R2 causes a fixed current to flow to ground. This current creates a voltage across R1 that adds to the 0.9 V across R2 and sets the overall output voltage. The output voltage is set according to the formula:
Vout + Vref R1 ) R2 * I Adj R2 R2
The adjust pin current, Iadj, is typically 30 nA and normally much lower than the current flowing through R1 and R2, thus it generates a small output voltage error that can usually be ignored.
Load Transient Measurement
Large load current changes are always presented in microprocessor applications. Therefore good load transient performance is required for the power stage. NCP565 has the feature of ultra fast transient response. Its load transient responses in Figures 9 through 12 are tested on evaluation board shown in Figure 15. On the evaluation board, it consists of NCP565 regulator circuit with decoupling and filter capacitors and the pulse controlled current sink to obtain load current transitions. The load current transitions are measured by current probe. Because the signal from current probe has some time delay, it causes un-synchronization between the load current transition and output voltage response, which is shown in Figures 9 through 12.
Vout -VCC Vin Pulse +
NCP565 Evaluation Board GND
V RL
+ GND Scope Voltage Probe
Figure 15. Schematic for Transient Response Measurement
http://onsemi.com
6
NCP565
PCB Layout Considerations
Good PCB layout plays an important role in achieving good load transient performance. Because it is very sensitive to its PCB layout, particular care has to be taken when tackling Printed Circuit Board (PCB) layout. The figures below give an example of a layout where parasitic elements are minimized. For microprocessor applications it is customary to use an output capacitor network consisting of
Vin 2 Vin
several capacitors in parallel. This reduces the overall ESR and reduces the instantaneous output voltage drop under transient load conditions. The output capacitor network should be as close as possible to the load for the best results. The schematic of NCP565 typical application circuit, which this PCB layout is base on, is shown in Figure 16. The output voltage is set to 3.3 V for this demonstration board according to the feedback resistors in the Table 1.
Vout 4 Vout
NCP565 C1 150 m C2 150 m 1 NC GND 3 GND GND R2 15.8 k R1 42.2 k C6 5.6 p Adj 5 C4 10 m C3 150 m C3 150 m
Figure 16. Schematic of NCP565 Typical Application Circuit
Figure 17. Top Layer
http://onsemi.com
7
NCP565
Figure 18. Bottom Layer
NCP565 ON Semiconductor www.onsemi.com D1 VIN R2
R1C6
C2
VOUT
C3 C4
C1 GND
C5 GND
July, 2003
Figure 19. Silkscreen Layer
Table 1. Bill of Materials for NCP565 Adj Demonstration Board
Item 1 2 3 4 5 6 Used # 4 1 1 1 1 1 Component Radial Lead Aluminum Capacitor 150 mF/16 V Radial Lead Aluminum Capacitor 10 mF/10 V SMT Chip Resistor (0805) 15.8 K 1% SMT Chip Resistor (0805) 42.2 K 1% SMT Ceramic Capacitor (0603) 5.6 pF 10% NCP565 Low Dropout Linear Regulator Designators C1, C2, C3, C5 C4 R2 R1 C6 U1 Suppliers Sanyo Oscon Sanyo Oscon Vishay Vishay Vishay ON Semiconductor Part Number 16SA150M 10SL10M CRCW08051582F CRCW08054222F VJ0603A5R6KXAA NCP565D2TR4
http://onsemi.com
8
NCP565
Protection Diodes Thermal Considerations
When large external capacitors are used with a linear regulator it is sometimes necessary to add protection diodes. If the input voltage of the regulator gets shorted, the output capacitor will discharge into the output of the regulator. The discharge current depends on the value of the capacitor, the output voltage and the rate at which Vin drops. In the NCP565 linear regulator, the discharge path is through a large junction and protection diodes are not usually needed. If the regulator is used with large values of output capacitance and the input voltage is instantaneously shorted to ground, damage can occur. In this case, a diode connected as shown in Figure 20 is recommended.
This series contains an internal thermal limiting circuit that is designed to protect the regulator in the event that the maximum junction temperature is exceeded. This feature provides protection from a catastrophic device failure due to accidental overheating. It is not intended to be used as a substitute for proper heat sinking. The maximum device power dissipation can be calculated by:
PD + TJ(max) * TA RqJA
1N4002 (Optional) Vin Vin C1 Vout CAdj R1 Vout
NCP565 GND Adj
C2
R2
The devices are available in surface mount D2PAK package. The package has an exposed metal tab that is specifically designed to reduce the junction to air thermal resistance, RqJA, by utilizing the printed circuit board copper as a heat dissipater. Figure 21 shows typical RqJA values that can be obtained from a square pattern using economical single sided 2.0 ounce copper board material. The final product thermal limits should be tested and quantified in order to insure acceptable performance and reliability. The actual RqJA can vary considerably from the graph shown. This will be due to any changes made in the copper aspect ratio of the final layout, adjacent heat sources, and air flow.
Figure 20. Protection Diode for Large Output Capacitors
PD, MAXIMUM POWER DISSIPATION (W) 80 R JA, THERMAL RESISTANCE PD(max) for TA = +50C 70 60 50 40 RqJA 30 0 5.0 10 15 20 L, LENGTH OF COPPER (mm) Free Air Mounted Vertically Minimum Size Pad 3.0 2.0 oz. Copper L 2.5 2.0 1.5 1.0 JUNCTION-TO-AIR ( C/W) 3.5
L
Figure 21. 3-Pin and 5-Pin D2PAK Thermal Resistance and Maximum Power Dissipation vs. P.C.B Length
http://onsemi.com
9
IIII IIII IIII IIII
25 30
NCP565
PACKAGE DIMENSIONS
D2PAK-3 D2T SUFFIX CASE 936-03 ISSUE B
-T- K A
OPTIONAL CHAMFER TERMINAL 4 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. TAB CONTOUR OPTIONAL WITHIN DIMENSIONS A AND K. 4. DIMENSIONS U AND V ESTABLISH A MINIMUM MOUNTING SURFACE FOR TERMINAL 4. 5. DIMENSIONS A AND B DO NOT INCLUDE MOLD FLASH OR GATE PROTRUSIONS. MOLD FLASH AND GATE PROTRUSIONS NOT TO EXCEED 0.025 (0.635) MAXIMUM. INCHES MIN MAX 0.386 0.403 0.356 0.368 0.170 0.180 0.026 0.036 0.045 0.055 0.051 REF 0.100 BSC 0.539 0.579 0.125 MAX 0.050 REF 0.000 0.010 0.088 0.102 0.018 0.026 0.058 0.078 5 _ REF 0.116 REF 0.200 MIN 0.250 MIN MILLIMETERS MIN MAX 9.804 10.236 9.042 9.347 4.318 4.572 0.660 0.914 1.143 1.397 1.295 REF 2.540 BSC 13.691 14.707 3.175 MAX 1.270 REF 0.000 0.254 2.235 2.591 0.457 0.660 1.473 1.981 5 _ REF 2.946 REF 5.080 MIN 6.350 MIN
E
U V
S B F
1 2 3
H M L P
J D 0.010 (0.254) M T
N G R
C
DIM A B C D E F G H J K L M N P R S U V
SOLDERING FOOTPRINT*
8.38 0.33
10.66 0.42
1.016 0.04
5.08 0.20
3.05 0.12 17.02 0.67
SCALE 3:1 mm inches
*For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D.
http://onsemi.com
10
NCP565
PACKAGE DIMENSIONS
D2PAK-5 D2T SUFFIX CASE 936A-02 ISSUE B
-T- A K B
12345 OPTIONAL CHAMFER
TERMINAL 6
E
U V
S H M L
NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. TAB CONTOUR OPTIONAL WITHIN DIMENSIONS A AND K. 4. DIMENSIONS U AND V ESTABLISH A MINIMUM MOUNTING SURFACE FOR TERMINAL 6. 5. DIMENSIONS A AND B DO NOT INCLUDE MOLD FLASH OR GATE PROTRUSIONS. MOLD FLASH AND GATE PROTRUSIONS NOT TO EXCEED 0.025 (0.635) MAXIMUM. INCHES MIN MAX 0.386 0.403 0.356 0.368 0.170 0.180 0.026 0.036 0.045 0.055 0.067 BSC 0.539 0.579 0.050 REF 0.000 0.010 0.088 0.102 0.018 0.026 0.058 0.078 5 _ REF 0.116 REF 0.200 MIN 0.250 MIN MILLIMETERS MIN MAX 9.804 10.236 9.042 9.347 4.318 4.572 0.660 0.914 1.143 1.397 1.702 BSC 13.691 14.707 1.270 REF 0.000 0.254 2.235 2.591 0.457 0.660 1.473 1.981 5 _ REF 2.946 REF 5.080 MIN 6.350 MIN
D 0.010 (0.254)
M
T
N G R
P
C
DIM A B C D E G H K L M N P R S U V
SOLDERING FOOTPRINT*
8.38 0.33
1.702 0.067 10.66 0.42 1.016 0.04
3.05 0.12 16.02 0.63
SCALE 3:1
mm inches
*For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D.
http://onsemi.com
11
NCP565
The product described herein (NCP565), may be covered by one or more of the following U.S. patents: 5,920,184; 5,834,926. There may be other patents pending.
ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 61312, Phoenix, Arizona 85082-1312 USA Phone: 480-829-7710 or 800-344-3860 Toll Free USA/Canada Fax: 480-829-7709 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Japan: ON Semiconductor, Japan Customer Focus Center 2-9-1 Kamimeguro, Meguro-ku, Tokyo, Japan 153-0051 Phone: 81-3-5773-3850 ON Semiconductor Website: http://onsemi.com Order Literature: http://www.onsemi.com/litorder For additional information, please contact your local Sales Representative.
http://onsemi.com
12
NCP565/D

▲Up To Search▲

Price & Availability of NCP565D2T

	To Download NCP565D2T Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .