 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| MC54/74F125 MC54/74F126 3-STATE QUAD BUFFERS * High Impedance NPN Base Inputs for Reduced Loading QUAD BUFFERS, 3-STATE MC54/74F125 VCC 14 4C 13 4A 12 4Y 11 3C 10 3A 9 3Y 8 FASTTM SHOTTKY TTL J SUFFIX CERAMIC CASE 632-08 14 1 1C 2 1A 3 1Y 4 2C 5 2A 6 2Y 7 GND 1 MC54/74F126 VCC 14 4C 13 4A 12 4Y 11 3C 10 3A 9 3Y 8 14 1 N SUFFIX PLASTIC CASE 646-06 14 1 D SUFFIX SOIC CASE 751A-02 1 1C 2 1A 3 1Y 4 2C 5 2A 6 2Y 7 GND ORDERING INFORMATION MC54FXXXJ MC74FXXXN MC74FXXXD Ceramic Plastic SOIC GUARANTEED OPERATING RANGES Symbol VCC TA Supply Voltage Operating Ambient Temperature Range Parameter 54, 74 54 74 IOH IOL Output Current -- High 54 74 Output Current -- Low 54 74 Min 4.5 -55 0 Typ 5.0 25 25 Max 5.5 125 70 -12 -15 48 64 mA mA Unit V C FAST AND LS TTL DATA 4-83 MC54/74F125 * MC54/74F126 Function Table MC54/74F125 Inputs C L L H A L H X Output Y L H Z Function Table MC54/74F126 Inputs C H H L A L H X Output Y L H Z L = LOW Voltage Level H = HIGH Voltage Level X = Don't Care Z = High Impedance (off) DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified) Limits Symbol VIH VIL VIK Parameter Input HIGH Voltage Input LOW Voltage Input Clamp Diode Voltage 54,74 74 VOH Output HIGH Voltage 54 74 54 VOL IOZH IOZL IIH Output LOW Voltage 74 Output Off Current HIGH Output Off Current LOW Input HIGH Current 0.55 50 -50 20 100 IIL IOS Input LOW Current Output Short Ciru`cuit Current Note 2 ICCH F125 ICCL ICCZ ICC F126 ICCH ICCL ICCZ -100 -20 -225 24 40 35 mA 30 48 39 VCC = MAX A A mA V A A 2.0 2.0 0.55 V V V 2.4 2.7 3.4 3.4 Min 2.0 0.8 -1.2 Typ Max Unit V V V V V Test Conditions Guaranteed Input HIGH Voltage Guaranteed Input LOW Voltage IIN = -18 mA IOH = -3.0 mA IOH = -3.0 mA IOH = -12 mA IOH = -15 mA IOL = 48 mA IOL = 64 mA VOUT = 2.7 V VOUT = 0.5 V VIN = 2.7 V VIN = 7.0 V VIN = 0.5 V VOUT = GND VCC = MAX VCC = MAX VCC = MAX VCC = 0 V VCC = MAX VCC = MAX VCC = MAX VCC = MIN VCC = 4.50 V VCC = 4.75 V VCC = 4.50 V NOTES: 1. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions for the applicable device type. 2. Not more than one output should be shorted at a time, nor for more than 1 second. FAST AND LS TTL DATA 4-84 MC54/74F125 * MC54/74F126 AC ELECTRICAL CHARACTERISTICS 54/74F TA = +25 C VCC = +5.0 V CL = 50 pF Symbol tPLH tPHL tPZH tPZL tPHZ tPLZ tPLH tPHL tPZH tPZL tPHZ tPLZ Parameter Propagation Delay, nA to nY Output Enable Time to HIGH and LOW level Output Disable Time from HIGH and LOW level Propagation Delay, nA to nY Output Enable Time to HIGH and LOW level Output Disable Time from HIGH and LOW level F126 F125 Min 1.5 3.0 3.0 3.0 1.5 1.5 1.5 3.0 3.0 3.0 2.0 3.0 Typ 4.0 5.5 5.5 6.0 3.5 3.5 4.0 5.5 6.0 6.0 4.5 5.5 Max 6.0 7.5 7.5 8.0 5.0 5.5 6.5 8.0 7.5 8.0 6.5 7.5 54F TA = 0C to 70C VCC = 5.0 V 10% CL = 50 pF Min 1.5 3.0 3.0 3.0 1.5 1.5 1.5 3.0 3.0 3.0 2.0 3.0 Max 7.5 9.0 9.5 10 7.0 7.0 8.0 9.5 9.5 9.5 8.5 9.0 74F TA = 0C to + 70C VCC = 5.0 V 10% CL = 50 pF Min 1.5 3.0 3.0 3.0 1.5 1.5 1.5 3.0 3.0 3.0 2.0 3.0 Max 6.5 8.0 8.5 9.0 6.0 6.0 7.0 8.5 8.5 8.5 7.5 8.0 ns ns ns ns ns Unit ns FAST AND LS TTL DATA 4-85 Case 751A-02 D Suffix 14-Pin Plastic SO-14 -A14 8 NOTES: 1. DIMENSIONS A" AND B" ARE DATUMS AND T" IS A DATUM SURFACE. 2. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 3. 4. CONTROLLING DIMENSION: MILLIMETER. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. 5. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 6. 751A 01 IS OBSOLETE, NEW STANDARD 751A 02. -B1 7 P 7 PL 0.25 (0.010) M B M G C SEATING PLANE R X 45 D 14 PL 0.25 (0.010) M K T B S M F J A S DIM A B C D F G J K M P R MILLIMETERS MIN MAX 8.55 3.80 1.35 0.35 0.40 8.75 4.00 1.75 0.49 1.25 INCHES MIN MAX 0.337 0.150 0.054 0.014 0.016 0.344 0.157 0.068 0.019 0.049 1.27 BSC 0.19 0.10 0 5.80 0.25 0.25 0.25 7 6.20 0.50 0.050 BSC 0.008 0.004 0 0.229 0.010 0.009 0.009 7 0.244 0.019 Case 632-08 J Suffix 14-Pin Ceramic Dual In-Line -A14 8 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. -B1 7 3. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. 4. DIM F MAY NARROW TO 0.76 (0.030) WHERE THE LEAD ENTERS THE CERAMIC BODY. 5. 632 01 THRU 07 OBSOLETE, NEW STANDARD C L 632 08. -TSEATING PLANE K F D 14 PL 0.25 (0.010) M G T A S N J 14 PL M 0.25 (0.010) M T B S DIM A B C D F G J K L M N MILLIMETERS MIN MAX 19.05 6.23 3.94 0.39 1.40 19.94 7.11 5.08 0.50 1.65 INCHES MIN MAX 0.750 0.245 0.155 0.015 0.055 0.785 0.280 0.200 0.020 0.065 2.54 BSC 0.21 3.18 0.38 4.31 0.100 BSC 0.008 0.125 0.015 0.170 7.62 BSC 0 0.51 15 1.01 0.300 BSC 0 0.020 15 0.040 Case 646-06 N Suffix 14-Pin Plastic NOTES: 1. LEADS WITHIN 0.13 mm (0.005) RADIUS OF TRUE POSITION AT SEATING PLANE AT MAXIMUM MATERIAL CONDITION. 14 8 B 1 7 2. DIMENSION L" TO CENTER OF LEADS WHEN FORMED PARALLEL. 3. DIMENSION B" DOES NOT INCLUDE MOLD FLASH. 4. 5. ROUNDED CORNERS OPTIONAL. 646 05 OBSOLETE, NEW STANDARD 646 06. A F C N H G D SEATING PLANE NOTE 4 L J K M DIM A B C D F G H J K L M N MILLIMETERS MIN MAX 18.16 6.10 3.69 0.38 1.02 19.56 6.60 4.69 0.53 1.78 INCHES MIN MAX 0.715 0.240 0.145 0.015 0.040 0.770 0.260 0.185 0.021 0.070 2.54 BSC 1.32 0.20 2.92 2.41 0.38 3.43 0.100 BSC 0.052 0.008 0.115 0.095 0.015 0.135 7.62 BSC 0 0.39 10 1.01 0.300 BSC 0 0.015 10 0.039 FAST AND LS TTL DATA 4-86 Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters can and do vary in different applications. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. Literature Distribution Centers: USA: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. EUROPE: Motorola Ltd.; European Literature Centre; 88 Tanners Drive, Blakelands, Milton Keynes, MK14 5BP, England. JAPAN: Nippon Motorola Ltd.; 4-32-1, Nishi-Gotanda, Shinagawa-ku, Tokyo 141, Japan. ASIA PACIFIC: Motorola Semiconductors H.K. Ltd.; Silicon Harbour Center, No. 2 Dai King Street, Tai Po Industrial Estate, Tai Po, N.T., Hong Kong. FAST AND LS TTL DATA 4-87 |
Price & Availability of MC54F125
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |