View 4065_967686.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

TS339C,I,M
MICROPOWER QUAD CMOS VOLTAGE COMPARATORS
s EXTREMELY LOW SUPPLY CURRENT : 9A
typ / comparator
s WIDE SINGLE SUPPLY RANGE: 2.7 TO 16V
OR DUAL SUPPLIES (1.35V TO 8V)
s EXTREMELY LOW INPUT BIAS CURRENT :
1pA typ
s EXTREMELY LOW INPUT OFFSET CURRENT : 1pA typ
N DIP14 (Plastic Package)
s INPUT COMMON-MODE VOLTAGE RANGE
INCLUDES GND
s HIGH INPUT IMPEDANCE : 1012 typ s FAST RESPONSE TIME : 1.5s typ for 5mV
overdrive
s PIN-TO-PIN AND FUNCTIONALLY COMPATIBLE WITH BIPOLAR LM339 DESCRIPTION The TS339 is a micropower CMOS quad voltage comparator with extremely low consumption of 9A typ / comparator (20 times less than bipolar LM339). Similar performances are offered by the quad micropower comparator TS3704 with a push-pull CMOS output. Thus response times remain similar to the LM339. ORDER CODE
Output 2
D SO14 (Plastic Micropackage)
P TSSOP14 (Thin Shrink Small Outline Package)
PIN CONNECTIONS (top view)
1
14 13 12 + + + + 11 10 9 8
Output 3 Output 4 V CC Non-inverting Input 4 Inverting Input 4 Non-inverting Input 3 Inverting Input 3
Part Number TS339C TS339I TS339M
Temperature Range 0C, +70C -40C, +125C -55C, +125C
Package N * * * D * * * P * * *
Output 1 2 VCC + 3
Inverting Input 1 4 Non-inverting Input 1 5 Inverting Input 2 Non-inverting Input 2 6 7
N = Dual in Line Package (DIP) D = Small Outline Package (SO) - also available in Tape & Reel (DT) P = Thin Shrink Small Outline Package (TSSOP) - only available in Tape & Reel (PT)
January 2003
1/7
TS339C,I,M
SCHEMATIC DIAGRAM (for 1/4 TS339)
VCC +
T 10 T1 T2 T9 T17
R1 Input T3 T4
T 11
T12 Input +
T 18
Output T 20 T 13 T8 T 19
T5 T6
T7
T14
T 15
T16
VCC -
ABSOLUTE MAXIMUM RATINGS
Symbol VCC+ Vid Vi Vo Io IF pd Tstg
1. 2. 3. 4. 5.
Parameter Supply Voltage 1) Differential Input Voltage Input Voltage
3) 2)
Value 18 18 18 18 20
4)
Unit V V V V mA mA mW C
Output Voltage Output Current Forward Current in ESD Protection Diodes on Inputs Power Dissipation 5) DIP14 SO14 TSSOP14
50 1500 830 710 -65 to +150
Storage Temperature Range
All voltage values, except differential voltage, are with respect to network ground terminal. Differential voltages are the non-inverting input terminal with respect to the inverting input terminal. The magnitude of the input and the output voltages must never exceed the magnitude of the possitive supply voltage. Guaranteed by design. Pd is calculated with T amb = +25C, Tj = +150C and R thja = 80 C/W for DIP14 package = 150 C/W for SO14 package = 175C/W for TSSOP14 package
OPERATING CONDITIONS
Symbol VCC+ Vicm Toper Supply Voltage Common Mode Input Voltage Range Operating Free-Air Temperature range TS339C TS339I TS339M Parameter TS339C,I TS339M Value 2.7 to 16 4 to 16 0 to VCC+ -1.5 0 to +70 -40 to +125 -55 to +125 Unit V V C
2/7
TS339C,I,M
ELECTRICAL CHARACTERISTICS VCC+ = 3V, V cc- = 0V, Tamb = 25C (unless otherwise specified)
Symbol Vio Input Offset Voltage Vic = 1.5V Tmin . Tamb Tmax. Input Offset Current 2) Vic = 1.5V Tmin . Tamb Tmax. Input Bias Current 2) Vic = 1.5V Tmin . Tamb Tmax. Input Common Mode Voltage Range Tmin . Tamb Tmax Common-mode Rejection Ratio Vic = Vicm min. Supply Voltage Rejection Ratio VCC+ = 3V to 5V High Level Output Current Vid = +1V, VOH = 3V Tmin . Tamb Tmax. Low Level Output Voltage Vid = -1V, IOL = +6mA Tmin . Tamb Tmax. Supply Current (each comparator) No load - Outputs low Tmin . Tamb Tmax. Response Time Low to High Vic = 0V, f = 10kHz, RL = 5.1k, CL = 50pF, Overdrive = 5mV TTL Input Response Time High to Low Vic = 0V, f = 10kHz, RL = 5.1k, CL = 50pF, Overdrive = 5mV TTL Input 0 0 70 70 2 40 1000 550 800 20 25 1 300 1 600 VCC+-1.2 VCC+ -1.5 V pA
1)
Parameter
Min.
Typ.
Max. 5 6.5
Unit mV
Iio
pA
Iib
Vicm CMR SVR IOH
dB dB nA
VOL
400
mV
ICC
9
A
tPLH
1.5 0.7 2.5 0.08
s
tPHL
s
1. The specified offset voltage is the maximun value required to drive the output up to 2.5V or down to 0.3V. 2. Maximum values including unavoidable inaccuracies of the industrial test.
3/7
TS339C,I,M
ELECTRICAL CHARACTERISTICS VCC+ = 5V, V CC- = 0V, Tamb = 25C (unless otherwise specified)
Symbol
1)
Parameter Input Offset Voltage Vic = 2.5V, Vcc+ = 5V to 10V Tmin. Tamb Tmax. Input Offset Current 2) Vic = 2.5V Tmin. Tamb Tmax. Input Bias Current 2) Vic = 2.5V Tmin. Tamb Tmax. Input Common Mode Voltage Range Tmin. Tamb Tmax Common-mode Rejection Ratio Vic = 0V Supply Voltage Rejection Ratio VCC+ = +5V to +10V High Level Output Voltage Vid = 1V, VOH = +5V Tmin. Tamb Tmax. Low Level Output Voltage Vid = -1V, IOL = 6mA Tmin. Tamb Tmax. Supply Current (each comparator) No load - Outputs low Tmin. Tamb Tmax. Response Time Low to High Vic = 0V, f = 10kHz, RL = 5.1k, CL = 15pF, Overdrive = 5mV Overdrive = 10mV Overdrive = 20mV Overdrive = 40mV TTL Input Response Time High to Low Vic = 0V, f = 10kHz, RL = 5.1k, CL = 15pF, Overdrive = 5mV Overdrive = 10mV Overdrive = 20mV Overdrive = 40mV TTL Input Fall time f = 10kHz, CL = 15pF, RL = 5.1k, Overdrive 50mV
Min.
Typ. 1.4
Max. 5 6.5
Unit mV
Vio
Iio
1 300 1 600 0 0 75 85 2 40 1000 400 650 20 25 VCC+-1.2 VCC+ -1.5
pA
Iib
pA
Vicm CMR SVR
V dB dB
IOH
nA
VOL
260
mV
ICC
10
A
tPLH
1.5 1.2 1.1 0.9 0.8 2.5 1.9 1.2 0.8 0.08 25
s
tPHL
s
tf
1. 2.
ns
The specified offset voltage is the maximun value required to drive the output up to 4.5V or down to 0.3V. Maximum values including unavoidable inaccuracies of the industrial test.
4/7
TS339C,I,M
PACKAGE MECHANICAL DATA 14 PINS - PLASTIC DIP
Millimeters Dimensions Min. a1 B b b1 D E e e3 F i L Z 0.51 1.39 0.5 0.25 20 8.5 2.54 15.24 7.1 5.1 3.3 1.27 2.54 0.050 Typ. Max. 1.65 Min. 0.020 0.055
Inches Typ. Max. 0.065 0.020 0.010 0.787 0.335 0.100 0.600 0.280 0.201 0.130 0.100
5/7
TS339C,I,M
PACKAGE MECHANICAL DATA 14 PINS - PLASTIC MICROPACKAGE (SO)
L C
G c1
a2 b e3 D M e
A
s E
14 1
8 7 F
Millimeters Dimensions Min. A a1 a2 b b1 C c1 D (1) E e e3 F (1) G L M S 0.1 0.35 0.19 0.5 45 (typ.) 8.55 5.8 1.27 7.62 3.8 4.6 0.5 4.0 5.3 1.27 0.68 8 (max.) 0.150 0.181 0.020 8.75 6.2 0.336 0.228 Typ. Max. 1.75 0.2 1.6 0.46 0.25 Min. 0.004 0.014 0.007
a1
Inches Typ. Max. 0.069 0.008 0.063 0.018 0.010 0.020 0.344 0.244 0.050 0.300 0.157 0.208 0.050 0.027
Note : (1) D and F do not include mold flash or protrusions - Mold flash or protrusions shall not exceed 0.15mm (.066 inc) ONLY FOR DATA BOOK.
6/7
b1
TS339C,I,M
PACKAGE MECHANICAL DATA 14 PINS - THIN SHRINK SMALL OUTLINE PACKAGE (TSSOP)
c
k
0,25 mm .010 inch GAGE PLANE L L1
E1
SEATING PLANE A A2 A1 b
C E
8
7
D
aaa
C
14
1
PIN 1 IDENTIFICATION
Millimeters Dimensions Min. A A1 A2 b c D E E1 e k L L1 aaa 0.05 0.80 0.19 0.09 4.90 4.30 0 0.450 Typ. Max. 1.20 0.15 1.05 0.30 0.20 5.10 4.50 8 0.750 0.100 Min. 0.01 0.031 0.007 0.003 0.192 0.169 0 0.018
e
Inches Typ. Max. 0.05 0.006 0.041 0.15 0.012 0.20 0.177 8 0.030 0.004
1.00
0.039
5.00 6.40 4.40 0.65 0.600 1.00
0.196 0.252 0.173 0.025 0.024 0.039
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. (c) The ST logo is a registered trademark of STMicroelectronics (c) 2003 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States (c) http://www.st.com
7/7

▲Up To Search▲

Price & Availability of 4065

	To Download 4065 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .