View 6818_969932.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

6818
DABiC-IV, 32-BIT SERIAL-INPUT, LATCHED SOURCE DRIVER
A6818xA
LOAD SUPPLY SERIAL DATA OUT OUT 32 OUT 31 OUT 30 OUT 29 OUT 28 OUT 27 OUT 26 OUT 25 OUT 24 OUT 23 OUT 22 OUT 21 OUT 20 OUT 19 OUT 18 OUT 17 BLANKING GROUND 1 2 3 4 5 6 7 8 9 VBB VDD 40 39 38 37 36 35 34 33 32 LOGIC SUPPLY SERIAL DATA IN OUT 1 OUT 2 OUT 3 OUT 4 OUT 5 OUT 6 OUT 7 OUT 8 OUT 9 OUT 10 OUT 11 OUT 12 OUT 13 OUT 14 OUT 15 OUT 16 STROBE CLOCK
Data Sheet 26182.128
The A6818- devices combine a 32-bit CMOS shift register, accompanying data latches and control circuitry with bipolar sourcing outputs and pnp active pull downs. Designed primarily to drive vacuumfluorescent displays, the 60 V and -40 mA output ratings also allow these devices to be used in many other peripheral power driver applications. The A6818- features an increased data input rate (compared with the older UCN/UCQ5818-F) and a controlled output slew rate. The CMOS shift register and latches allow direct interfacing with microprocessor-based systems. With a 3.3 V or 5 V logic supply, typical serial-data input rates are up to 33 MHz. A CMOS serial data output permits cascade connections in applications requiring additional drive lines. Similar devices are available as the A6809- and A6810- (10 bits), A6811- (12 bits), and A6812- (20 bits). The A6818- output source drivers are npn Darlingtons, capable of sourcing up to 40 mA. The controlled output slew rate reduces electromagnetic noise, which is an important consideration in systems that include telecommunications and/or microprocessors and to meet government emissions regulations. For inter-digit blanking, all output drivers can be disabled and all sink drivers turned on with a BLANKING input high. The pnp active pull-downs will sink at least 2.5 mA. Three temperature ranges are available for optimum performance in commercial (suffix S-), industrial (suffix E-), or automotive (suffix K-) applications. Package styles are provided for through-hole DIP (suffix -A) or minimum-area surface-mount PLCC (suffix -EP). Copper lead frames, low logic-power dissipation, and low output-saturation voltages allow these devices to drive most multiplexed vacuum-fluorescent displays over the maximum operating temperature range.
REGISTER
REGISTER
LATCHES
LATCHES
10 11 12 13 14 15 16 17 18 19 20 BLNK
31 30 29 28 27 26 25 24 23 ST CLK 22 21
Dwg. PP-029-4
ABSOLUTE MAXIMUM RATINGS
at TA = 25C
Logic Supply Voltage, VDD ................... 7.0 V Driver Supply Voltage, VBB ................... 60 V Continuous Output Current Range, IOUT ......................... -40 mA to +15 mA Input Voltage Range, VIN ....................... -0.3 V to VDD + 0.3 V Package Power Dissipation, PD ........................................ See Graph Operating Temperature Range, TA (Suffix `E-') .................. -40C to +85C (Suffix `K-') ................ -40C to +125C (Suffix `S-') .................. -20C to +85C Storage Temperature Range, TS ............................... -55C to +125C
Caution: These CMOS devices have input static protection (Class 2) but are still susceptible to damage if exposed to extremely high static electrical charges.
FEATURES
s Controlled Output Slew Rate s Low Output-Saturation Voltages s High-Speed Data Storage s Low-Power CMOS Logic s 60 V Minimum and Latches Output Breakdown s Improved Replacements s High Data Input Rate for SN75518N, SN75518NF, s PNP Active Pull-Downs UCN5818-, and UCQ5818- Complete part number includes a suffix to identify operating temperature range (E-, K-, or S-) and package type (-A or -EP). Always order by complete part number, e.g., A6818SEP .
6818 32-BIT SERIAL-INPUT, LATCHED SOURCE DRIVER
TYPICAL INPUT CIRCUIT
OUT30 OUT31
A6818xEP
SERIAL DATA OUT LOAD SUPPLY LOGIC SUPPLY SERIAL DATA IN OUT32 OUT 1
44
43
OUT 2 41
NC
OUT29
7 8 9 10
V DD
VBB
42
40
6
3
5
4
2
1
OUT3
VDD
2
39 38 37 36
OUT 4
IN
REGISTER
REGISTER
LATCHES
LATCHES
11 12 13 14 15 16 OUT19 17
35 34 33 19 32 31 30 29 OUT13 NC
Dwg. EP-010-5
OUT 8
BLNK
CLK
20
ST
27 OUT14
18
23
19
24
25
21
22
OUT17
BLANKING
GROUND
STROBE
OUT15
NC
OUT18
OUT 16
26
CLOCK
NC
28
Dwg. PP-059-2
TYPICAL OUTPUT DRIVER
V BB
3.0
ALLOWABLE PACKAGE POWER DISSIPATION IN WATTS
2.5
SUFFIX 'A', R JA = 36C/W
OUTN
2.0
1.5
SUFFIX 'EP', RJA = 46C/W
Dwg. EP-021-19
1.0
0.5
0 25 50 75 100 125 AMBIENT TEMPERATURE IN C 150
Dwg. GP-025A
115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 Copyright (c) 1998, Allegro MicroSystems, Inc.
6818 32-BIT SERIAL-INPUT, LATCHED SOURCE DRIVER
FUNCTIONAL BLOCK DIAGRAM
CLOCK SERIAL DATA IN STROBE V DD LOGIC SUPPLY SERIAL DATA OUT
SERIAL-PARALLEL SHIFT REGISTER
LATCHES
BLANKING MOS BIPOLAR LOAD SUPPLY
VBB
GROUND
OUT 1 OUT 2 OUT 3
OUT N
Dwg. FP-013-1
TRUTH TABLE
Serial Shift Register Contents Data Clock Input Input I1 I2 I3 ... IN-1 IN H L X H L R1 R2 ... R1 R2 ... RN-2 RN-1 RN-2 RN-1 RN-1 RN X X Serial Data Strobe Output Input RN-1 RN-1 RN X PN L H R1 R2 R3 ... P1 P2 P3 ... X
L = Low Logic Level H = High Logic Level X = Irrelevant
Latch Contents I1 I2 I3 ... IN-1 IN Blanklng
Output Contents I1 I2 I3 ... IN-1 I N
R1 R2 R3 ... X X X ...
RN-1 RN PN-1 PN X X L H P1 P2 P3 ... PN-1 PN L L L ... L L
P1 P2 P3 ...
PN-1 PN
X
X
...
P = Present State
R = Previous State
6818 32-BIT SERIAL-INPUT, LATCHED SOURCE DRIVER
ELECTRICAL CHARACTERISTICS at TA = +25C (A6818S-) or over operating temperature range (A6818E- and A6818K-), VBB = 60 V unless otherwise noted.
Limits @ VDD = 3.3 V Characteristic Output Leakage Current Output Voltage Symbol I CEX VOUT(1) VOUT(0) Output Pull-Down Current Input Voltage IOUT(0) VIN(1) VIN(0) Input Current IIN(1) IIN(0) Input Clamp Voltage Serial Data Output Voltage VIK VOUT(1) VOUT(0) Maximum Clock Frequency Logic Supply Current fc IDD(1) IDD(0) Load Supply Current IBB(1) IBB(0) Blanking-to-Output Delay tdis(BQ) t en(BQ) Strobe-to-Output Delay tp(STH-QL) tp(STH-QH) Output Fall Time Output Rise Time Output Slew Rate tf tr dV/dt All Outputs High All Outputs Low All Outputs High, No Load All Outputs Low CL = 30 pF, 50% to 50% CL = 30 pF, 50% to 50% RL = 2.3 k, C L 30 pF RL = 2.3 k, C L 30 pF RL = 2.3 k, C L 30 pF RL = 2.3 k, C L 30 pF RL = 2.3 k, C L 30 pF IOUT = 200 A VIN = VDD VIN = 0.8 V IIN = -200 A IOUT = -200 A IOUT = 200 A Test Conditions VOUT = 0 V IOUT = -25 mA IOUT = 1 mA VOUT = 5 V to VBB Mln. -- 57.5 -- 2.5 2.2 -- -- -- -- 2.8 -- 10 -- -- -- -- -- -- -- -- 2.4 2.4 4.0 -- Typ. <-0.1 58.3 1.0 5.0 -- -- <0.01 <-0.01 -0.8 3.05 0.15 33 0.25 0.25 4.5 0.2 0.7 1.8 0.7 1.8 -- -- -- 50 Max. -15 -- 1.5 -- -- 1.1 1.0 -1.0 -1.5 -- 0.3 -- 0.75 0.75 9.0 20 2.0 3.0 2.0 3.0 12 12 20 -- Limits @ VDD = 5 V Min. -- 57.5 -- 2.5 3.3 -- -- -- -- 4.5 -- 10 -- -- -- -- -- -- -- -- 2.4 2.4 4.0 -- Typ. <-0.1 58.3 1.0 5.0 -- -- <0.01 Max. -15 -- 1.5 -- -- 1.7 1.0 Units A V V mA V V A A V V V MHz mA mA mA A s s s s s s V/s ns
<-0.01 -1.0 -0.8 4.75 0.15 33 0.3 0.3 4.5 0.2 0.7 1.8 0.7 1.8 -- -- -- 50 -1.5 -- 0.3 -- 1.0 1.0 9.0 20 2.0 3.0 2.0 3.0 12 12 20 --
Clock-to-Serial Data Out Delay tp(CH-SQX)
Negative current is defined as coming out of (sourcing) the specified device terminal. Typical data is is for design information only and is at TA = +25C.
115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000
6818 32-BIT SERIAL-INPUT, LATCHED SOURCE DRIVER
TIMING REQUIREMENTS and SPECIFICATIONS
(Logic Levels are VDD and Ground)
C CLOCK A SERIAL DATA IN DATA
50%
B
50%
t p(CH-SQX) SERIAL DATA OUT D STROBE
50% 50%
DATA E
BLANKING
LOW = ALL OUTPUTS ENABLED t p(STH-QH) t p(STH-QL)
90%
OUT N
DATA
10%
Dwg. WP-029
HIGH = ALL OUTPUTS BLANKED (DISABLED) BLANKING
50%
t dis(BQ) t en(BQ) OUT N tr
90% 10%
tf
DATA
A. Data Active Time Before Clock Pulse (Data Set-Up Time), tsu(D) ......................................... 25 ns B. Data Active Time After Clock Pulse (Data Hold Time), th(D) ............................................... 25 ns C. Clock Pulse Width, tw(CH) ............................................... 50 ns D. Time Between Clock Activation and Strobe, t su(C) ....... 100 ns E. Strobe Pulse Width, tw(STH) ............................................. 50 ns NOTE - Timing is representative of a 10 MHz clock. Significantly higher speeds are attainable.
Dwg. WP-030
Information present at any register is transferred to the respective latch when the STROBE is high (serial-toparallel conversion). The latches will continue to accept new data as long as the STROBE is held high. Applications where the latches are bypassed (STROBE tied high) will require that the BLANKING input be high during serial data entry. When the BLANKING input is high, the output source drivers are disabled (OFF); the pnp active pull-down sink drivers are ON. The information stored in the latches is not affected by the BLANKING input. With the BLANKING input low, the outputs are controlled by the state of their respective latches.
Serial Data present at the input is transferred to the shift register on the logic "0" to logic "1" transition of the CLOCK input pulse. On succeeding CLOCK pulses, the registers shift data information towards the SERIAL DATA OUTPUT. The SERIAL DATA must appear at the input prior to the rising edge of the CLOCK input waveform.
6818 32-BIT SERIAL-INPUT, LATCHED SOURCE DRIVER
A6818EA, A6811KA, & A6811SA
Dimensions in Inches (controlling dimensions)
40 0.015 0.008 21
0.700
MAX
0.580 0.485
0.600
BSC
1
2 0.070 0.030
3
4 2.095 1.980
20 0.100
BSC
0.005
MIN
0.250
MAX
0.015
MIN
0.200 0.115 0.022 0.014
Dwg. MA-003-40 in
Dimensions in Millimeters (for reference only)
40 0.381 0.204 21
17.78 14.73 12.32
MAX
15.24
BSC
1
2 1.77 0.77
3
4 53.2 50.3
2.54
BSC
20
0.13
MIN
6.35
MAX
0.39
MIN
5.08 2.93 0.558 0.356
Dwg. MA-003-40 mm
NOTES: 1. Exact body and lead configuration at vendor's option within limits shown. 2. Lead spacing tolerance is non-cumulative. 3. Lead thickness is measured at seating plane or below.
115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000
6818 32-BIT SERIAL-INPUT, LATCHED SOURCE DRIVER
A6818EEP, A6818KEP, & A6818SEP
Dimensions in Inches (controlling dimensions)
28 18
29 0.319 0.291 0.021 0.013 0.695 0.685 0.656 0.650 0.319 0.291 0.050
BSC INDEX AREA
17
0.032 0.026
39
7
40 0.020
MIN
44
1
2
6
0.656 0.650 0.695 0.685
Dwg. MA-005-44A in
0.180 0.165
Dimensions in Millimeters (for reference only)
28 18
29 8.10 7.39 0.533 0.331 17.65 17.40 16.662 16.510
INDEX AREA
17
0.812 0.661
8.10 7.39 1.27
BSC
39
7
40 0.51
MIN
44 16.662 16.510
1
2
6
4.57 4.20
17.65 17.40
Dwg. MA-005-44A mm
NOTES: 1. Exact body and lead configuration at vendor's option within limits shown. 2. Lead spacing tolerance is non-cumulative.
6818 32-BIT SERIAL-INPUT, LATCHED SOURCE DRIVER
BiMOS II (Series 5800) & DABiC IV (Series 6800) INTELLIGENT POWER INTERFACE DRIVERS SELECTION GUIDE
Function
8-Bit (saturated drivers) 8-Bit 8-Bit 8-Bit 8-Bit 8-Bit (constant-current LED driver) 9-Bit 10-Bit (active pull-downs) 12-Bit (active pull-downs) 16-Bit (constant-current LED driver) 20-Bit (active pull-downs) 32-Bit (active pull-downs) 32-Bit 32-Bit (saturated drivers)
Output Ratings *
SERIAL-INPUT LATCHED DRIVERS -120 mA 350 mA 350 mA 350 mA 350 mA 75 mA 1.6 A -25 mA -25 mA 75 mA -25 mA -25 mA 100 mA 100 mA 50 V 50 V 80 V 50 V 80 V 17 V 50 V 60 V 60 V 17 V 60 V 60 V 30 V 40 V
Part Number
5895 5821 5822 5841 5842 6275 5829 5810-F and 6809/10 5811 and 6811 6276 5812-F and 6812 5818-F and 6818 5833 5832
PARALLEL-INPUT LATCHED DRIVERS 4-Bit 8-Bit 8-Bit 350 mA -25 mA 350 mA 50 V 60 V 50 V 5800 5815 5801
SPECIAL-PURPOSE FUNCTIONS Unipolar Stepper Motor Translator/Driver Addressable 28-Line Decoder/Driver 1.25 A 450 mA 50 V 30 V 5804 6817
* Current is maximum specified test condition, voltage is maximum rating. See specification for sustaining voltage limits. Negative current is defined as coming out of (sourcing) the output. Complete part number includes additional characters to indicate operating temperature range and package style. Internal transient-suppression diodes included for inductive-load protection.
Allegro MicroSystems, Inc. reserves the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the design of its products. The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, Inc. assumes no responsibility for its use; nor for any infringements of patents or other rights of third parties which may result from its use.
115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000

▲Up To Search▲

Price & Availability of 6818

	To Download 6818 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .