View A84C1_973587.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

V23806-A84-C1
Single Mode 155 MBd ATM 2x9 Transceiver
Dimensions in (mm) inches
View Z (Lead cross section and standoff size) (0.730.1) .028.004 (1.50.1) .06.004
(40.2) .158.008
(11.5 max) .453 max. PC board thickness (2) .080 Optical Centerline (7 .42-0.15) .292-.006
PC board 2x 0.3 M A .012 M A
6.375 (0.750.1) .251 .030.004
(0.450.1) .0175.004 18x 0.3 M A .012 M A
20x
Z
0.2 M .008 M
(1.4-0.05) .055-.002 Top View
18 17 16 15 14 13 12 11 10
123456789
q q
q q
(25.40.1) 1.004 8x 2.54=20.32 8x .100 =.800
q q q q q q q
q q q q q q q
DUPLEX SC RECEPTACLE
12.7 .500
(20 -1) .787 -.040
A
2.54 .100
20.32 .800
7 .62 (15.880.5) .300 .625.020 (48.350.1) 1.9035.004
(12.60.3) .496.012
Absolute Maximum Ratings Exceeding any one of these values may destroy the device immediately. Package Power Dissipation(1) ........................................................ 1.5 W Supply Voltage (VCC-VEE).................................................................. 6 V Data Input Levels ........................................................VEE to VCC+0.5 V Differential Data Input Voltage......................................... -2.5 V to 2.5 V Operating Ambient Temperature .........................................0C to 70 C Storage Ambient Temperature......................................... -40C to 85 C Soldering Conditions Temp/Time (MIL -STD 883C, Method 2003) ......................................... 250 C/5.5s FEATURES * Compliant with existing standards * Compact integrated transceiver unit with - MQW laser diode transmitter - InGaAs PIN photodiode receiver - Duplex SC receptacle * Class 1 FDA laser safety compliant * FDA Accession No. 9520890 * IEC Class 3B laser safety compliant * May be upgraded to IEC Class 1 laser safety compliance with external laser shutdown * Single power supply (5V) * Loss of optical signal indicator * Integrated clock recovery module (PLL) * PECL differential inputs and outputs * Process plug included * Wave solderable and washable with process plug inserted
Semiconductor Group
Note 1. For VCC-VEE (min., max.). 50% duty cycle. The supply current does not include the load drive current of the receiver output. Add max. 45 mA for the three outputs. Load is 50 to VCC-2 V.
Pin Description
Pin# 1 2 3 4 5 6 7 Name Rx VEE Rx D Rx Dn SD Rx VCC Tx VCC Tx Dn Pin# 8 9 10 11 11 12 13 Name Tx D Tx VEE NC Tx Alm Tx Alm Tx En Bias Mon Pin# 14 15 16 17 18 S1, S2 Name Pwr Mon NC NC NC NC VEE (GND)
FEBRUARY 1998
DESCRIPTION This data sheet describes the Siemens single mode ATM transceiver, which complies with the ATM Forum's Network Compatible ATM for Local Network Applications document and ANSI's Broadband ISDN-- Customer Installation Interfaces, Physical Media Dependent Specification, T1.646-1995. ATM was developed to facilitate solutions in multimedia applications and real time transmission. The data rate is scalable, and the ATM protocol is the basis of the broadband public networks being standardized in the International Telecommunications Union (ITU), the former International Telegraph and Telephone Consultative Committee (CCITT). ATM can also be used in local private applications. This Siemens single mode ATM transceiver is a single unit comprised of a transmitter, a receiver, and an SC receptacle. This design frees the customer from many alignment and PC board layout concerns. The module is designed for low cost WAN applications. It can be used as the network end device interface in workstations, servers, and storage devices, and in a broad range of network devices such as bridges, routers, and intelligent hubs, and wide area ATM switches. The transceiver operates at 155.520 Mbits per second from a single power supply (+5 Volt). The full differential data inputs and data and clock outputs are PECL compatible. Functional Description of 2x9 Pin Row Transceiver This transceiver is designed to transmit serial data via single mode cable. Functional Diagram
TxEN BIAS MON TxD TxD Laser Coupling Unit
and aging. The power control uses the output of the monitor PIN diode (mechanically built into the laser coupling unit) as a controlling signal, to prevent the laser power from exceeding the operating limits. The laser can be switched on with a logical high signal on the Laser Enable pin (LEN). The PWRMON pin shows a voltage reflecting the optical power output. The bias current is monitored on the BIASMON pin. Both signals can be used to supervise the function of the module. The signal TXALM indicates an increase of the optical output power by more than 2dB. Aging control is possible using the bias monitor output (BIASMON). To build an IEC Class 1 laser system it is necessary to use an application circuit to switch off the laser if a fault occurs. TECHNICAL DATA The electro-optical characteristics described in the following tables are valid only for use under the recommended operating conditions. Recommended Operating Conditions
Parameter Ambient Temperature Power Supply Voltage Supply Current(1) Transmitter Data Input High Voltage Data Input Low Voltage VIH-VCC VIL-VCC -1165 -1810 0.4 2 0.8 0.8 -1 3.2 0.7 -3 3 25 1260 1360 mA nm mA V mA -880 -1475 1.3 ns V mV Symbol TAMB VCC-VEE ICC Min. 0 4.75 5.0 150 Typ. Max. 70 5.25 250 Units C V mA
Input Data Rise/Fall, 10%-90% tR, tF TxEN Input High Voltage VTIH TxEN Input Low Voltage TxEN Input High Current TxEN Input Low Current TxALM Output High Voltage TxALM Output Low Voltage TxALM Output High Current TxALM Output Low Current Receiver Output Current VTIL VTIH VTIL VTOH VTOL ITOH ITOL IO C
Laser Driver Power Control
Monitor
e/o
Laser
o/e Single Mode Fiber RX Coupling Unit o/e
TXALM PWRMON
Input Center Wavelength
RxD RxD SD
Receiver
Note 1. For VCC-VEE (min., max.). 50% duty cycle. The supply current does not include the load drive current of the receiver output. Add max. 45 mA for the three outputs. Load is 50 to VCC-2 V.
The receiver component converts the optical serial data into PECL compatible electrical data (RD and RDnot). The Signal Detect (SD, active high) shows whether an optical signal is present. If no optical input signal is present the receiver data outputs are switched to static low level (RD=low, RDnot=high). The transmitter converts electrical PECL compatible serial data (TD and TDnot) into optical serial data. It contains a laser driver circuit that drives the modulation and bias current of the laser diode. The currents are controlled by a power control circuit to guarantee constant output power of the laser over temperature
Transmitter Electro-Optical Characteristics
Transmitter Output Power (Average) Center Wavelength Spectral Width (FWHM) Output Rise Time Output Fall Time Extinction Ratio (Dynamic) Eye Diagram(1) Symbol PO C tR tF ER 8.2 Min. -15 1260 Typ. -11 Max. -8 1360 7.7 2.5 3 dB ns Units dBm nm
Note 1. Transmitter meets ANSI T1E1.2, SONET OC-3, and ITU G957 mask patterns.
Semiconductor Group
V23806-A84-C1, Single Mode 155 MBd ATM 2x9 Transceiver
2
Receiver Electro-Optical Characteristics
Receiver Sensitivity (Average Power)(1) Saturation (Average Power) Signal Detect Assert Level(2) Signal Detect Deassert Level(3) Signal Detect Hysteresis Signal Detect Assert Time(4) Signal Detect Deassert Time(5) Output Low Voltage(6) Output High Voltage(6) Output Data Rise /Fall Time, 10%-90% Output SD Rise/Fall Time(7) Symbol PIN PSAT PSDA PSDD PSDA- PSDD tASS tDAS VOL- VCC VOH- VCC tR, tF -1950 -1025 -42 -8 Min. Typ. -33 -7 -36 37.5 1.5 1 5 -1630 -735 1.3ns 40ns ns mV dB ms -33 Max. -29.0 Units dBm
Notes 1. Minimum average optical power at which the BER is less than 1x10E-10. Measured with a 223-1 NRZ PRBS as recommended by ANSI T1E1.2, SONET OC-3, and ITU G.957 . 2. An increase in optical power above the specified level will switch the SIGNAL DETECT from a Low state to a High state. 3. A decrease in optical signal below the specified level will switch the SIGNAL DETECT from a High state to a Low state. 4. Measured by switching the light from <-40 dBm to -25 dBm. 5. Measured by switching the light from -25 dBm to <-40 dBm. Switching from higher power levels increases this time. 6. PECL compatible. Load is 50 into VCC -2 V. Measured under DC conditions at 25C. For dynamic measurements a tolerance of 50 mV should be added, VCC=5 V. 7 PECL compatible. A high level on this output shows that an optical . signal is applied to the optical input.
Pin Description 2x9 Pin Row
Pin Name RxVEE RxD RxDn SD RxVCC TxVCC TxDn TxD TxVEE NC Tx Alm TxEn Bias Mon Tx+2dB Alarm Tx Enable Bias Monitor TTL Output active high TTL-Input active high Analog Voltage Tx Ground Power Supply RX Signal Detect PECL-Output active high Rx +5 V Tx +5 V Tx Input Data PECL Input Power Supply Rx Ground Rx Output Data Level Power Supply PECL Output Pin # 1 2 3 4 5 6 7 8 9 10 11 12 13 Inverted transmitter input data Transmitter input data Negative power supply, normally ground Pin not connected High level on this output indicates an increase of optical operating power output of+2 dB. High level on this input switches the laser on. High>2.0; Low<0.8 Shows an analog voltage that is proportional to the laser bias current. Use to check proper laser operation and for end of life indications. Limit: Bias Current IBIAS<60mA Output Voltage VO=VCC-IBIAS * 42 , Source Resistance RS=500 Ohm Shows an analog voltage that is proportional to the light output and can be used for laser safety functions. Output Voltage Vmon=2.0 0.2 V, Source Resistance RS=100 k Pins not connected Description Negative power supply, normally ground Receiver output data Inverted receiver output data High level on this output shows an optical signal is applied to the optical input. Positive power supply, +5 V
Pwr Mon(1)
Power Monitor
14
NC
15-18
Note 1. For laser fault supervision, check that this output meets the criteria 1.5 VSemiconductor Group
V23806-A84-C1, Single Mode 155 MBd ATM 2x9 Transceiver
3
LASER SAFETY This single mode ATM transceiver is an FDA Class 1 laser product. It complies with FDA 21 CFR 1040.10 and 1040.11. This transceiver is an IEC Class 3B laser product per IEC 825-1. It may be upgraded to an IEC Class 1 laser product when operated with external shutdown circuitry in accordance with the Application Note in this document. The transceiver must be operated under recommended operating conditions. Caution The use of optical instruments with this product will increase eye hazard! General Restrictions Classification is valid only if the module is operated within the specified temperature and voltage limits. The system using the module must provide power supply protection that guarantees that the system power source will cease to provide power if the maximum recommended operation limit or more is detected on the +5V at the power source. The operating temperature of the module must be in the temperature range given in the recommended operating limits. These limits guarantee the laser safety. Usage Restrictions The optical ports of the modules shall be terminated with an optical connector or with a dust plug.
Note Failure to adhere to the above restrictions could result in a modification that is considered an act of "manufacturing, and will require, " under law, recertification of the modified product with the U.S. Food and Drug Administration (ref. 21 CFR 1040.10 (i)).
Required Labels FDA
Complies with 21 CFR 1040.10 and 1040.11
IEC
Invisible Laser Radiation Avoid Exposure to Beam Class 3B Laser Product
Laser Emission
Indication of laser aperture and beam
Regulatory Compliance
Feature Standard Comments Class 1 (>1000 V) Electrostatic MIL-STD 883C Discharge (ESD) Method 3015.4 to the Electrical Pins Immunity: Electrostatic Discharge (ESD) to the Duplex SC Receptacle Immunity: Radio Frequency Electromagnetic Field EN 61000-4-2 IEC 1000-4-2
Discharges of 15kV with an air discharge probe on the receptacle cause no damage. With a field strength of 10 V/m rms, noise frequency ranges from 10 MHz to 1 GHz. No effect on transceiver performance between the specification limits.
EN 61000-4-3 IEC 1000-4-3
Laser Data
Wavelength Total output power (as defined by IEC: 50 mm aperture at 10 cm distance) 1300 nm 2 mW Emission: Electromagnetic Interference (EMI)
Maximum output power (as defined by IEC 825-1 30 mW under fault condition) Total output power (as defined by FDA: 7 mm aperture at 20 cm distance) Beam divergence 180 W 4
FCC Class B Noise frequency range: EN 55022 Class B 30 MHz to 1 GHz CISPR 22
Semiconductor Group
V23806-A84-C1, Single Mode 155 MBd ATM 2x9 Transceiver
4
APPLICATION NOTE FOR 2X9 PIN ROW TRANSCEIVER Proposal for Automatic Laser Shutdown
Backfacet-Monitor VCC VCC 500 VCC 500
2,5 k
1/2 LM
1k
&
&
&
1,5 k VCC L1 VCC-RX
1/2 LM 4,7 k
VCC
& C2 VCC-Tx
q q q q q q q q q 18 qqqqqqqqq
VCC
C1
TDIS TXAL I BIAS
GND L2
GND
VCC-TX
VCC 3 MAX 809 RESET 2 82 RESET TxD TxD not 130 see Notes
VCC-Tx
82 10 130
82
82 Rx D Rx D SD
GND
GND
C3
C4
RESET MAX 811
GND
GND
C1/3=4700 nF (optional) C2/4=4700 nF L1/2=15000 nH (L2 optional)(3)
GND GND Automatic Power RESET Test Transceiver
200 130 130 GND GND GND
DC coupling between ECL gates.
Notes 1. Minimum length of RESET pulse is 3 ms. 2. After switch on (VCC) manual RESET necessary or automatic RESET with IC (e. g. MAX 809). 3. Recommended choke is Siemens Matsushita B78108-S1153-K or B78148 S1153-K (Qmin=60, max. DC resistance=0.6 Ohm)
RESET low high
Function Norm Fail Norm Fail
C high low high low
Laser ON
TDIS high high*
The shutdown circuit checks the monitor voltage (PWRMON). A deviation of 0.5 V shuts down the laser in the circuit shown above. The transceiver can be reenabled using the reset circuit. The power supply filtering is required for good EMI performance. Use short tracks from the inductor L1/L2 to the module VCC-RX/VCC-TX. A GND plane under the module is required for good EMI and sensitivity performance. Studs must be connected to this GND plane.
OFF
low
Depends on previous flip-flop state.
Siemens Microelectronics, Inc. * Optoelectronics Division * 19000 Homestead Road * Cupertino, CA 95014 USA Siemens Semiconductor Group * Fiber Optics * Wernerwerkdamm 16 * Berlin D-13623, Germany www.smi.siemens.com/opto.html (USA) * www.siemens.de/Semiconductor/products/37/376.htm (Germany)

▲Up To Search▲

Price & Availability of A84C1

	To Download A84C1 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .