View A84C3_973590.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

V23806-A84-C3
Single Mode 155 MBd ATM 1x9 Transceiver Extended Temperature Range (-40C to 85C)
Dimensions in (mm) inches
View Z (Lead cross section and standoff size) (0.730.1) .028.004 (1.50.1) .06.004
(40.2) .158.008 (a)
(11.5 max) .453 max. (2) .080 Optical Centerline (0.750.1) .030.004
(7 .42-0.15) .292-.006 (9.6+0.1) .378+.004 6.375 .251
9x (0.8) min. .032 min. 11x 0.1 M .004 M
PC board 2x
PC board thickness 11x (0.5) typ. .020 typ. (0.25) typ. .010 typ. (25.40.1) 9x 1.004 0.3 M A 8x 2.54=20.32 .012 M A 8x .100 =.800
Z
q q q q q q q q q
0.1 M .004 M
0.3 M A .012 M A
q q q
(1.4-0.05) .055-.002 (b) Top View Rx DUPLEX SC RECEPTACLE Tx 12.7 .500
q q
8x 2.54=20.32 8x .100 =.800 (20 -1) .787 -.040
q q
123456789
q q
(2.54) .100 (2.54) .100
20.32 .800
(1.90.1) 2x .075.004
A
20.32 .800 (38.620.1) 1.52.004
(15.880.5) .625.020
(12.60.3) .496.012
a. Different length of pins available. maximum: (7 .295 .5) b. Isolated posts on request
Absolute Maximum Ratings Exceeding any one of these values may destroy the device immediately. Package Power Dissipation(1) ........................................................ 1.5 W Supply Voltage (VCC-VEE).................................................................. 6 V Data Input Levels (GND) ........................................................VCC+0.5 V Differential Data Input Voltage........................................................ 2.5 V Operating Ambient Temperature ..................................... -40C to 85C Storage Ambient Temperature......................................... -40C to 85C Soldering Conditions, Temp/Time (MIL -STD 883C, Method 2003) ......................................... 250C/5.5s
Note 1. For VCC-VEE (min., max.). 50% duty cycle. The supply current does not include the load drive current of the receiver output. Add max. 45 mA for the three outputs. Load is 50 to VCC-2 V.
FEATURES * Compliant with existing standards * Compact integrated transceiver unit with - MQW laser diode transmitter - InGaAs PIN photodiode receiver - Duplex SC receptacle * Class 1 FDA and IEC laser safety compliant * Single power supply (5 V) * Loss of optical signal indicator * PECL differential inputs and outputs * Process plug included * Wave solderable and washable with process plug inserted
DESCRIPTION This data sheet describes the Siemens single mode ATM transceiver, which complies with the ATM Forum's Network Compatible ATM for Local Network Applications document and ANSI's Broadband ISDN Customer Installation Interfaces, Physical Media Dependent Specification, T1E1.2. ATM was developed to facilitate solutions in multimedia applications and real time transmission. The data rate is scalable, and the ATM protocol is the basis of the broadband public networks being standardized in the International Telecommunications Union (ITU), the former International Telegraph and Telephone Consultative Committee (CCITT). ATM can also be used in local private applications.
FEBRUARY 1998
Semiconductor Group
The Siemens single mode ATM transceiver is a single unit comprised of a transmitter, receiver and an SC receptacle. This design frees the customer from many alignment and PC board layout concerns. The module is designed for low cost LAN and WAN applications. It can be used as the network end device interface in workstations, servers, and storage devices, and in a broad range of network devices such as bridges, routers, and intelligent hubs, as well as local and wide area ATM switches. This transceiver operates at 155.520 Mbits per second from a single power supply (+5 Volt). The full differential data inputs and outputs are PECL compatible. Functional Description of 1x9 Pin Row Transceiver This transceiver is designed to transmit serial data via single mode cable. Functional Diagram
Automatic Shut-Down
LEN TD TD Laser Coupling Unit e/o
TECHNICAL DATA The electro-optical characteristics described in the following tables are valid only for use under the recommended operating conditions. Recommended Operating Conditions
Parameter Ambient Temperature Power Supply Voltage Supply Current (1) Transmitter Data Input High Voltage VIH-VCC Data Input Low Voltage Input Data Rise/Fall Time, 10%-90% Receiver Output Current Input Center Wavelength IO C 1260 25 1360 mA nm VIL-VCC tR, tF -1165 -1810 0.4 -880 -1475 1.3 ns mV Symbol TAMB ICC Min. -40 5.0 150 Typ. Max. 85 5.25 270 Units C V mA
VCC-VEE 4.75
Laser Driver Power Control
Monitor
Laser
o/e Single Mode Fiber RX Coupling Unit o/e
Note 1. For VCC-VEE (min., max.). 50% duty cycle. The supply current does not include the load drive current of the receiver output. Add max. 45 mA for the three outputs. Load is 50 to VCC-2 V.
Transmitter Electro-Optical Characteristics
Transmitter Output Power (Average) Center Wavelength Spectral Width (FWHM) Output Rise Time Output Fall Time Extinction Ratio (Dynamic), at -40C Reset Threshold for TXVCC(1) Eye Diagram(2)
Notes 1. Laser power is shut down if power supply is below VTH and switched on if power supply is above VTH after tRES. 2. Transmitter meets ANSI T1E1.2, SONET OC-3, and ITU G.957 mask patterns.
Symbol PO C tR tF ER VTH
Min. Typ. -15 1260 0.6 8.2 4.25 140 4.38 240 -11
Max. Units -8 7.7 2.5 3 dB 4.5 560 V ms ns dBm 1360 nm
RD RD SD
Receiver
The receiver component converts the optical serial data into PECL compatible electrical data (RD and RDnot). The Signal Detect (SD, active high) shows whether an optical signal is present. The transmitter converts electrical PECL compatible serial data (TD and TDnot) into optical serial data. It contains a laser driver circuit that drives the modulation and bias current of the laser diode. The currents are controlled by a power control circuit to guarantee constant output power of the laser over temperature and aging. The power control uses the output of the monitor PIN diode (mechanically built into the laser coupling unit) as a controlling signal, to prevent the laser power from exceeding the operating limits. This module is a Class 1 laser product, due to an integrated automatic shutdown circuit that disables the laser when it detects transmitter failures. The transceiver contains a supervisory circuit to monitor the power supply. This circuit makes an internal reset signal whenever the supply voltage drops below the reset threshold. It keeps the reset signal active for at least 140 milliseconds after the voltage has risen above the reset threshold. During this time the laser is inactive.
Reset Active Time Out(1) TRES
Semiconductor Group
V23806-A84-C3, Single Mode 155 MBd ATM 1x9 Transceiver, Ext. Temp. Range
2
Receiver Electro-Optical Characteristics
Receiver Sensitivity (Average Power)(1) Saturation (Average Power) Signal Detect Assert Level(2) Signal Detect Deassert Level(3) Signal Detect Hysteresis Signal Detect Assert Time(4) Signal Detect Deassert Time(5) Symbol PIN PSAT PSDA PSDD PSDA- PSDD TASS TDAS -8 -43 -44.5 1 10 30 -1950 -1.13 -36 37.5 1.5 30 150 -33.5 Min. Typ. -33 Max. -29 Units dBm
Pin Description 1x9 Pin Row
Pin Name RxVEE RD RDn Rx SD -35 3 100 350 TD -1630 -735 1.3 40 ns mV TxVEE Tx Ground Power Supply Ground dB RxVCC Rx +5 V s TxVCC TDn Tx +5 V Tx Input Data Level Pin # Description 1 2 3 4 Negative power supply, normally ground Receiver output data Inverted receiver output data A high level on this output shows that an optical signal is applied to the optical input. Positive power supply, +5 V Inverted transmitter input data Transmitter input data Negative power supply, normally ground VEE/GND Support Stud (GND) connect to VEENB Rx Ground Power Supply Rx Output Data RX Signal Detect PECL Output PECL Output active high Power Supply PECL Input
5 6 7 8 9 S1/2
Output Low Voltage(6) VOL-VCC Output High Voltage(6) VOH-VCC Output Data Rise/Fall Time, 10%-90% Output SD Rise/Fall Time(7) t ,t
RF
Regulatory Compliance
Feature Standard Comments Class 1 (>1000 V) Electrostatic MIL-STD 883C Discharge (ESD) Method 3015.4 to the Electrical Pins Immunity: Electrostatic Discharge (ESD) to the Duplex SC Receptacle Immunity: Radio Frequency Electromagnetic Field EN 61000-4-2 IEC 1000-4-2
Notes 1. Minimum average optical power at which the BER is less than 1 x 10E-10. Measured with a 223-1 NRZ PRBS as recommended by ANSI T1E1.2, SONET OC-3, and ITU G.957 . 2. An increase in optical power above the specified level will cause the SIGNAL DETECT to switch from a Low state to a High state. 3. A decrease in optical power below the specified level will cause the SIGNAL DETECT to switch from a High state to a Low state. 4. Measured by switching the light from <-40 dBm to -25 dBm. 5. Measured by switching the light from -25 dBm to <-40 dBm. Switching from higher power levels increases this time. 6. PECL compatible. Load is 50 into VCC-2 V. Measured under DC conditions at 25C. For dynamic measurements a tolerance of 50 mV should be added, VCC=5 V. 7 PECL compatible. A high level on this output shows that an optical . signal is applied to the optical input.
Discharges of 15kV with an air discharge probe on the receptacle cause no damage. With a field strength of 10 V/m rms, noise frequency ranges from 10 MHz to 1 GHz. No effect on transceiver performance between the specification limits. Noise frequency range: 30 MHz to 1 GHz
EN 61000-4-3 IEC 1000-4-3
Emission: Electromagnetic Interference (EMI)
FCC Class B EN 55022 Class B CISPR 22
Semiconductor Group
V23806-A84-C3, Single Mode 155 MBd ATM 1x9 Transceiver, Ext. Temp. Range
3
LASER SAFETY This single mode ATM transceiver is a Class 1 laser product. It complies with IEC 825-1 and FDA 21 CFR 1040.10 and 1040.11. The transceiver must be operated under recommended operating conditions. Caution The use of optical instruments with this product will increase eye hazard! General Restrictions Classification is valid only if the module is operated within the specified temperature and voltage limits. The system using the module must provide power supply protection that guarantees that the system power source will cease to provide power if the maximum recommended operation limit or more is detected on the +5 V at the power source. The operating temperature of the module must be in the temperature range given in the recommended operating limits. These limits guarantee the laser safety. Usage Restrictions The optical ports of the modules shall be terminated with an optical connector or with a dust plug.
Note Failure to adhere to the above restrictions could result in a modification that is considered an act of "manufacturing, and will require, " under law, recertification of the modified product with the U.S. Food and Drug Administration (ref. 21 CFR 1040.10 (i)).
Laser Data
Wavelength Total output power (as defined by IEC: 50 mm aperture at 10 cm distance) Total output power (as defined by FDA: 7 mm aperture at 20 cm distance) Beam divergence 1300 nm 2 mW 180 W 4
Required Labels
FDA
Complies with 21 CFR 1040.10 and 1040.11
IEC
Class 1 Laser Product
Laser Emission
Indication of laser aperture and beam
APPLICATION NOTE FOR 1X9 PIN ROW TRANSCEIVER
VCC L1 VCC-RX VCC-TX C2 82R 82R VCC-TX 9 1 82R VCC-RX
VCC
C1
GND L2
GND
R1
R3
R5
82R
GND
GND
R7
TXD
C3 C4
TXDN
VCC-TX 130R 200R 130R 130R 130R
RD RDN SD
R2 R4
VCC-RX GND GNDGND GND
R9
R8
GND
GND
C1/3=4700 nF (optional) R1/3/5/7=82 Ohm C2/4=4700 nF R2/4/6/8=130 Ohm L1/2=1500 nH (L2 optional)* R9=200 Ohm
R6 GND GNDGND
Transceiver
DC coupling between ECL gates.
* Recommended choke is Siemens Matsushita B78108-S1153-K or B78148-S1153-K (Qmin=60, max. DC resistance=0.6 Ohm).
The power supply filtering is required for good EMI performance. Use short tracks from the inductor L1/L2 to the module VCC-RX/ VCC-TX. A GND plane under the module is required for good EMI and sensitivity performance. Studs must be
connected to this GND plane. The transceiver contains an automatic shutdown circuit. Reset is only possible if the power is turned off, and then on again. VCCTX switched below VTH.
Siemens Microelectronics, Inc. * Optoelectronics Division * 19000 Homestead Road * Cupertino, CA 95014 USA Siemens Semiconductor Group * Fiber Optics * Wernerwerkdamm 16 * Berlin D-13623, Germany www.smi.siemens.com/opto.html (USA) * www.siemens.de/Semiconductor/products/37/376.htm (Germany)

▲Up To Search▲

Price & Availability of A84C3

	To Download A84C3 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .