View AAT4651_973657.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

5V/3V PC Card Power Switch General Description
The AAT4651 SmartSwitchTM is a single channel PC Card (PCMCIA) power switch. It is used to select between two different voltage inputs, each between 2.7V and 5.5V. An internal switch powers the circuitry from whichever input voltage is higher. The device's output, VCC, is slew rate controlled and current limited, in compliance with PC Card specifications. The current limit response time to a short circuit is typically 1s. The internal P-Channel MOSFET switches are configured to break before make, that is, both switches cannot be closed at the same time. Controlled by a 2 bit parallel interface, the three states for VCC are VCC5, VCC3, or Ground. When in the ground state, VCC is pulled to ground by an 200 resistor. An open drain FAULT output is asserted during over-current conditions. During power up slewing, FAULT also signals that VCC is out of tolerance. An internal over temperature sensor forces VCC to a high impedance state when an over-temperature condition exists. Quiescent current is typically a low 15A, as long as ICC is less than approximately 500mA. Above this load current, the quiescent current increases to 200A. The AAT4651 is available in 8-pin SOP and TSSOP packages specified over -40 to 85C.
AAT4651
Features
* * * * * * * * *
SmartSwitchTM
2.7V to 5.5V Input voltage range 80m (5V) typical RDS(ON) Low quiescent current 15A (typ) Reverse-blocking switches Short-circuit protection Over-temperature protection FAULT flag output Temp range -40 to 85C 8 pin SOP or TSSOP package
Applications
* * * Notebook Computer PDA, Subnotebook Power Supply Multiplexer Circuit
Typical Application
VCC5 VCC3 VCCD1 VCCD0 FAULT
CIN5 1F CIN3 1F
8 5 2 3 4 1
VCC5 VCC3 VCCD1 VCCD0 FAULT GND
AAT4651
VCC
6,7
VCC
COUT 0.1F
GND
GND
4651.2004.04.1.0
1
5V/3V PC Card Power Switch Pin Descriptions
Pin #
1 2 3 4 5 6 7 8
AAT4651
Symbol
GND VCCD1 VCCD0 FAULT VCC3 VCC VCC VCC5
Function
Ground connection Control input (see Control Logic Table below) Control input (see Control Logic Table below) Open drain output signals over-current condition 3V supply Output (see Control Logic Table below) Output (see Control Logic Table below) 5V supply
Pin Configuration
SO-8 / TSSOP-8 (Top View)
GND VCCD1 VCCD0 FAULT
1 2
8 7
3 4
6 5
VCC5 VCC VCC VCC3
1 2
Control Logic Table
VCCD1
0 0 1 1
VCCD0
0 1 0 1
Function
OFF 3.3V 5V OFF
Result
80 VCC to GND VCC=VCC3 VCC=VCC5 80 VCC to GND
2
4651.2004.04.1.0
5V/3V PC Card Power Switch Absolute Maximum Ratings
Symbol
VCC3, VCC5 VCC IMAX TJ VESD
AAT4651
(TA=25C unless otherwise noted) Value
-0.3 to 6 -0.3 to 6 Current Limited -40 to 150 4000
Description
IN to GND OUT to GND Maximum Continuous Switch Current Operating Junction Temperature Range ESD Rating1 -- HBM
Units
V V A C V
Note: Stresses above those listed in Absolute Maximum Ratings may cause permanent damage to the device. Functional operation at conditions other than the operating conditions specified is not implied. Only one Absolute Maximum rating should be applied at any one time. Note 1: Human body model is a 100pF capacitor discharged through a 1.5k resistor into each pin.
Thermal Characteristics
Symbol
JA JA PD PD
Description
Thermal Resistance (SOP-8) Thermal Resistance (TSSOP-8)2 Power Dissipation (SOP-8)2 Power Dissipation (TSSOP-8)2
2
Value
120 150 1.0 833
Units
C/W C/W W mW
Note 2: Mounted on an FR4 board.
Electrical Characteristics
Symbol Description
VCC Output Iccsc Short Circuit Current Limit
(VCC5 = 5.0V, VCC3 = 3.3V, TA = -40 to 85C unless otherwise noted. Typical values are at TA=25C; bold values designate full temperature range) Conditions Min Typ Max Units
2.5 A
RDS(ON) On-Resistance RCLAMP Clamp Resistance Tcrds Switch Resistance Tempco VCC Switching Time (Refer to Figure 1) t1 Output Turn-On Delay Time t2 Output Turn-On Delay Time t3 Output Rise Time t4 Output Rise Time t5 Output Turn-Off Delay Time t6 Output Turn-Off Delay Time t7 Output Fall Time to OFF State t8 Output Fall Time to OFF State
VCC=VCCIN -0.5V, ON mode VCC3 1.0 or VCC5 selected, TA=25C VCC=3.0v, TA=25C VCC=5.0v, TA=25C VCC = clamped to GND, ICCOUT =10mA sinking
85 110 m 80 100 m 80 200 2800 ppm/C 2000 1500 3000 3000 400 400 200 200 s s s s s s s s
VCC=0v to 10% of 3.3V, ROUT=10 VCC=0v to 10% of 5.0V, ROUT=10 VCC=10% to 90% of 3.3V, RLOAD=10 VCC=10% to 90% of 5.0V, RLOAD=10 VCC=3.3 to 90% of 3.3V, RLOAD=10 VCC=5.0 to 90% of 5.0V, RLOAD=10 VCC=90% to 10% of 3.3V, RLOAD=10 VCC=90% to 10% of 5.0V, RLOAD=10
500 500 300 1000 300 1000
4651.2004.04.1.0
3
5V/3V PC Card Power Switch
Symbol Description Conditions Min
2.7 2.7 VCC=5V or OFF, VCC3VCC3, ICC Out=0 VCC=3.3v, VCC5>VCC3 ,ICC Out=0 VCC=5v, VCC5>VCC3, ICC Out=0 VCC3 or VCC5=3.0 to 5.5V VCC3 or VCC5=2.7 to 3.6V VCC3 or VCC5=4.5 to 5.5V VCTL = 5.5V ISINK=1mA VFAULT= 5.5V
3
AAT4651
Typ
Max Units
5.5 5.5 1 V V A A A A A V V V A V A
Power Supply VCC3 VCC3 Operation Voltage VCC5 VCC5 Operation Voltage ICC3 VCC3 Supply Current
5 10 15
ICC5
VCC5 Supply Current
20 1 40 40 0.8
Parallel Interface VCCD LOW VCCD Input Low Voltage VCCD HI VCCD Input High Voltage ISINK VCCD VFAULTLOW ISINKFAULT Other OTMP VCCD Input leakage FAULT Logic Output Low Voltage FAULT Logic Output High Leakage Current Over Temperature Shutdown
2.0 2.4 0.01 1 0.4 1
0.05
125
degC
Note 3: For VCCD outside this range consult Typical VCCD Threshold curve.
Timing Diagram
5 0 5
VCCD0,1
0
Vcc t1, t2 t3, t4 t5, t6 t7, t8
Figure 1: VCC Switching Time Diagram Refer to VCC Switching Time specifications under the Electrical Characteristics section for definitions of t1 to t8.
4
4651.2004.04.1.0
5V/3V PC Card Power Switch Typical Characteristics
(Unless otherwise noted, TA = 25C)
Quiescent Current vs. Temperature (ICC5)
2
AAT4651
Current Limit VCC=VCC3
Quiescent Current (A)
30 25 20 15 10 5 0 -40 -20 0 20 40 60 80 100 120
0 0 0.5
VCC3=3V VCC5=5V
VCCD1=5V VCCD0=0V
1.5
Ta=25C
1
0.5
1
1.5
2
2.5
3
Temperature (C)
Vout
Current Limit VCC=VCC5
Off-Switch Current (A)
2
Off-Switch Current vs. Temperature (ICC3)
1.0000 0.1000 0.0100 0.0010 0.0001 0.0000 -40 -20 0 20 40 60 80 100 120
Ta=25C
1.5
VCC3=3V VCC5=5V
VCCD1=0V VCCD0=0V
1
0.5
0 0 1 2 3 4 5 6
Vout
Temperature (C)
Off-Switch Current vs. Temperature ICC5
Off-Switch Current (A)
1.0000 0.1000 0.0100 90.0 0.0010 0.0001 0.0000 -40 -20 0 20 40 60 80 100 120 80.0 70.0 60.0 -40 120.0
Rdson vs. Temperature
VCC5=5V VCC3=3V
VCCD1=0V VCCD0=0V
110.0 100.0
VCC=VCC3=3.0V VCC=VCC5=5.0V
-20 0 20 40 60 80 100 120
Temperature (C)
Temperature (C)
4651.2004.04.1.0
5
5V/3V PC Card Power Switch
(Unless otherwise noted, TA = 25C)
AAT4651
Turn-ON/OFF Response with 10, 1F load (VCCD1 = 0V)
Turn-ON/OFF Response with 15, 1F load (VCCD0 = 0V)
VCCD0(5V/div)
FAULT (5V/div)
VCCD1(5V/div) FAULT (5V/div) VCC (2V/div) IVCC5 (200mA/div)
500s/div
VCC (2V/div) IVCC3 (200mA/div)
500s/div
Thermal Shutdown Response (VCCD0 = 0V)
8
Short Circuit Through 0.3 Ohm
11
Input and Output (V)
VCCD1 (5V/div) FAULT (5V/ div)
4
5
VCC (1V/ div)
Output Current
2 2
Output Voltage
0 -2 0 2 4 6 8 10 -1
IVCC5 (500mA/ div)
100ms / div
Time (s)
Short Circuit Through 0.6 Ohm
8 9
VCCD Threshold vs. VCC
VCCD Threshold Voltage (V)
2.5 2.3 2.1 1.9 1.7 1.5 1.3 1.1 0.9 0.7 0.5 2.5 3.0 3.5 4.0 4.5 5.0 5.5
Input and Output (V)
4
Output Current Output Voltage
Output (A)
6
Input Voltage
6
3
VCCDH VCCDL
2
0
0 -2 0 2 4 6 8 10
-3
Time (s)
VCC (V)
6
4651.2004.04.1.0
Output (A)
6
Input Voltage
8
5V/3V PC Card Power Switch Functional Block Diagram
VCC 3 VCC 5
AAT4651
Body Ctl VCC
Over Current
Over Current
Over Temperature
Slew Rate
Slew Rate
80 FAULT
VCCD1 VCCD0
Control Logic
GND
Functional Description
The AAT4651 is a single channel power switch that can be used in any application where dual power supply multiplexing is required. Typical applications for this include PC card applications not requiring a 12 volt power supply, or applications where power is switched, for example, between 5 volts for operation and 3.3 volts for standby mode. The AAT4651 operates with input voltages ranging from 2.7 to 5.5 volts in any combination and automatically powers its internal circuitry off of whichever input voltage is higher. Two identical low RDS P-channel MOSFETS serve as the power multiplexing circuit with a common drain as the Vcc output and independent sources as the two Vcc3 and Vcc5 inputs. A two bit parallel interface determines the state of the multiplexer: Vcc=Vcc3, Vcc=Vcc5, or Vcc with resistive pull down to ground. When the state is set to either of the two inputs, the multiplexing circuit will slowly
slew the VCC output to the new voltage level which protects the upstream power supply from sudden load transients. When the resistive pull down is chosen for VCC, the VCC output is quickly discharged by the resistive pull down. The AAT4651 always serves as an electronic fuse by limiting the load current if it exceeds the current limit threshold. During power up into a short, the current will gradually increase until the current limit is reached. During a sudden short circuit on the output, the current limit will respond in 1 s to isolate and protect the upstream power supply from the load short circuit. In most applications, because the response time is so fast, a short circuit to VCC will not affect the upstream supply, so system functionality will not be affected. In the case of an over current condition, an open drain FAULT flag output will signal the event. The FAULT output is also active during output voltage slew, and becomes inactive once the output is within regulation.
4651.2004.04.1.0
7
5V/3V PC Card Power Switch Applications Information
Input Capacitor
Typically a 1F or larger capacitor is recommended for CIN. A CIN capacitor is not required for basic operation, however, it is useful in preventing load transients from affecting up stream circuits. CIN should be located as close to the device VIN pin as practically possible. Ceramic, tantalum or aluminum electrolytic capacitors may be selected for CIN. There is no specific capacitor ESR requirement for CIN. However, for higher current operation, ceramic capacitors are recommended for CIN due to their inherent capability over tantalum capacitors to withstand input current surges from low impedance sources such as batteries in portable devices. AAT4651 is dominated by voltage regulation rather than by thermal considerations, and is set by either the current limit or the maximum RDS of the P-channel MOSFET. The maximum RDS at 85C is calculated by applying the RDS Tempco to the maximum room temperature RDS: RDS(MAX) = RDS25 x (1 + (TC x T)), or RDS(MAX) = 100m x (1 + (0.0028 x 60)) = 116.8m The maximum current is equal to the 2% tolerance of the 5 volt supply (100mV) across the AAT4651 divided by RDS(MAX). Or IMAX5 = 100mV / 116.8m = 856.2mA For the 3.3 volt supply in the PC card application, the conditions are a bit relaxed, with the allowable voltage regulation drop equal to 300mV. With a 2% supply, and 1% PCB trace regulation, the PC card switch can have a 200mV drop. So IMAX3 = 200mV / 134m = 1.5A Since 1.5A is the nominal current limit value, the AAT4651 will current limit before IMAX3 is reached.. Thermal issues are not a problem in the SO-8 package since JA, the package thermal resistance, is only 120C/W. At any given ambient temperature (TA) the maximum package power dissipation can be determined by the following equation: PD(MAX) = [TJ(MAX) - TA] / JA Constants for the AAT4651 are maximum junction temperature, TJ(MAX) = 125C, and package thermal resistance, JA = 120C/W. Worst case conditions are calculated at the maximum operating temperature where TA = 85C. Typical conditions are calculated under normal ambient conditions where TA = 25C. At TA = 85C, PD(MAX) = 333mW. At TA = 25C, PD(MAX) = 833mW. Maximum current is given by the following equation: IOUT(MAX) = (PD(MAX) / Rds)1/2 For the AAT4651 at 85C, IOUT(MAX) = 1.65A, a value greater than the internal minimumcurrent limit specification.
AAT4651
Output Capacitor
A 0.1F or greater capacitor is generally required between Vcc and GND. Likewise, with the output capacitor, there is no specific capacitor ESR requirement. If desired, COUT may be increased to accommodate any load transient condition.
Parallel Interface / Break Before Make
A two bit parallel interface determines the state of the Vcc output. The logic levels are compatible with CMOS or TTL logic. A logic low value must be less than 0.8 volts, and a logic high value must be greater than 2.4 volts. In cases where the interface pins rapidly change state directly from 3v to 5v (or vice versa), internal break before make circuitry prevents any back flow of current from one input power supply to the other. In addition, the body connections of the internal P-channel MOSFET switches are always set to the highest potential of Vcc3, Vcc5, or Vcc, which prevents any body diode conduction, power supply backflow, or possible device damage.
FAULT Output
The FAULT output is pulled to ground by an open drain N-channel MOSFET during an over current or output slew condition. It should be pulled up to the reference power supply of the controller IC via a nominal 100K resistor.
Voltage Regulation
The PC Card Specification calls for a regulated 5 volt supply tolerance of +/-5%. Of this, a typical power supply will drop less than 2%, and the PCB traces will drop another 1%. This leaves 2% for the AAT4651 as the PC card switch. In the PC card application, the maximum allowable current for the 8
Overcurrent and Overtemperature Protection
Because many AAT4651 applications provide power to external devices, it is designed to protect its host device from malfunctions in those peripherals
4651.2004.04.1.0
5V/3V PC Card Power Switch
through slew rate control, current limiting, and thermal limiting. The AAT4651 current limit and thermal limit serve as an immediate and reliable electronic fuse without any increase in RDS for this function. Other solutions such as a poly fuse do not protect the host power supply and system from mishandling, or short circuited peripherals, they will only prevent a fire. The AAT4651 high speed current limit and thermal limit not only prevent fires, they also isolate the power supply and entire system from any activity at the external port, and report a mishap by means of a FAULT signal. Overcurrent and overtemperature go hand in hand. Once an overcurrent condition exists, the current supplied to the load by the AAT4651 is limited to the overcurrent threshold. This results in a voltage drop across the AAT4651 which causes excess power dissipation and a package temperature increase. As the die begins to heat up, the overtemperature circuit is activated. If the temperature reaches the maximum level, the AAT4651 automatically switches off the P-channel MOSFETs. While they are off, the overtemperature circuit remains active. Once the temperature has cooled by approximately 10C, the P-channel MOSFETs are switched back on. In this manner, the AAT4651 is thermally cycled on and off until the short circuit is removed. Once the short is removed, normal operation automatically resumes. To save power, the full high speed overcurrent circuit is not activated until a lower threshold of current (approximately 500mA) is exceeded in the power device. When the load current exceeds this crude threshold, the AAT4651 quiescent current increases from 15A to 200A. The high speed overcurrent circuit works by linearly limiting the current when the current limit is reached. As the voltage begins to drop on Vcc due to current limiting, the current limit magnitude varies, and generally decreases as the Vcc voltage drops to 0 volts.
AAT4651
Switching Vcc Voltage
The AAT4651 meets PC card standards for switching the Vcc output by providing a ground path for Vcc as well as "off" state. The PC card protocol for determining low voltage operations is to first power the peripheral with 5 volts and poll for 3.3 volt operation. When transitioning from 5 volts to 3.3 volts, Vcc must be discharged to less than 0.8 volts to provide a hard reset. The resistive ground state (VCCD0=VCCD1) will accommodate this. The ground state will also guarantee the Vcc voltage to be discharged within the specified 100ms amount of time.
Printed Circuit Board Layout Recommendations
For proper thermal management, to minimize PCB trace resistance, and to take advantage of the low RDS(ON) of the AAT4651, a few circuit board layout rules should be followed: Vcc3, Vcc5, and Vcc should be routed using wider than normal traces, the two Vcc pins (6 and 7) should be connected to the same wide PCB trace, and GND should be connected to a ground plane. For best performance, CIN and COUT should be placed close to the package pins.
Typical PC Card Application Circuit
Power 5V Supply 3.3V
CIN5 1F
100K
8 5 2
PC Card Controller
VCC
CIN3 1F
3 4 1
VCC5 VCC3 VCCD1 VCCD0 FAULT GND
AAT4651
VCC
6,7
PC Card Slot
VCC COUT 0.1F
FAULT VCC_EN1 VCC_EN0
4651.2004.04.1.0
9
5V/3V PC Card Power Switch Evaluation Board Layout
The AAT4651 evaluation layout follows the printed circuit board layout recommendations, and can be used for good applications layout. Note: Board layout shown is not to scale.
AAT4651
Figure 2: Evaluation board top side silk screen layout / assembly drawing
Figure 3: Evaluation board component side layout
Figure 4: Evaluation board solder side layout
10
4651.2004.04.1.0
5V/3V PC Card Power Switch Ordering Information
Package SOP-8 TSSOP-8 Marking 4651 4651 Part Number (Tape and Reel) AAT4651IAS-T1 AAT4651IHS-T1
AAT4651
Note: Sample stock is generally held on all part numbers listed in BOLD.
Package Information
SOP-8
3.90 0.10 4.90 0.10
6.00 0.20
0.375 0.125 1.55 0.20
45
0.175 0.075
4 4
0.235 0.045 0.825 0.445
0.42 0.09 x 8
1.27 BSC
All dimensions in millimeters.
4651.2004.04.1.0
11
5V/3V PC Card Power Switch
TSSOP-8
AAT4651
4.40 0.10
6.40 0.20
3.00 0.10 0.65 BSC
12 REF x 4
1.05 MAX
1.20 MAX
0.145 0.055 4 4
0.245 0.055 x 8
0.10 0.05 12
0.60 0.15 1.00 REF
DETAIL A
All dimensions in millimeters.
AnalogicTech cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in an AnalogicTech product. No circuit patent licenses, copyrights, mask work rights, or other intellectual property rights are implied. AnalogicTech reserves the right to make changes to their products or specifications or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability. AnalogicTech warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with AnalogicTech's standard warranty. Testing and other quality control techniques are utilized to the extent AnalogicTech deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed.
Advanced Analogic Technologies, Inc.
830 E. Arques Avenue, Sunnyvale, CA 94085 Phone (408) 737-4600 Fax (408) 737-4611 12
4651.2004.04.1.0

▲Up To Search▲

Price & Availability of AAT4651

	To Download AAT4651 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .