View NSC05334_994304.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MICROCIRCUIT DATA SHEET MJLM111-X REV 0C1
VOLTAGE COMPARATOR
General Description
The LM111, is a voltage comparator that has input currents nearly a thousand times lower than devices such as the LM106 and LM710. It is also designed to operate over a wider range of supply voltages: from standard +15V op amp supplies down to the single 5V supply used for IC logic. Its output is compatible with RTL, DTL and TTL as well as MOS circuits. Further, it can drive lamps or relays, switching voltages up to 50V at currents as high as 50mA. Both the inputs and the outputs of the LM111, can be isolated from system ground, and the output can drive loads referred to ground, the positive supply or the negative supply. Offset balancing and strobe capability are provided and outputs can be wire OR'ed. Although slower than the LM106 and LM710 (200 ns response time vs 40ns) the devices are also much less prone to spurious oscillations. The LM111 has the same pin configuration as the LM106 and LM710. Original Creation Date: 08/18/95 Last Update Date: 08/24/98 Last Major Revision Date: 09/05/96
Industry Part Number
LM111
NS Part Numbers
JL111BCA JL111BGA JL111BHA JL111BPA JL111SGA JL111SHA JL111SPA
Prime Die
LM111
Controlling Document
38510/10304, AMEND.1 REV E
Processing
MIL-STD-883, Method 5004
Subgrp Description
1 2 3 4 5 6 7 8A 8B 9 10 11 Static tests at Static tests at Static tests at Dynamic tests at Dynamic tests at Dynamic tests at Functional tests at Functional tests at Functional tests at Switching tests at Switching tests at Switching tests at
Temp ( oC)
+25 +125 -55 +25 +125 -55 +25 +125 -55 +25 +125 -55
Quality Conformance Inspection
MIL-STD-883, Method 5005
1
MJLM111-X REV 0C1
MICROCIRCUIT DATA SHEET
Features
Low Input Bias Current. Low Input Offset Current. Wide Differential Input Voltage. Power Supply Voltage, Single 5V to +15V. Offset Voltage Null Capability. Strobe Capability.
2
MJLM111-X REV 0C1
MICROCIRCUIT DATA SHEET
(Absolute Maximum Ratings)
(Note 1) Positive Supply Voltage +30.0V Negative Supply Voltage -30.0V Total Supply Voltage 36V Output to Negative Supply Voltage 50V GND to Negative Supply Voltage 30V Differential Input Voltage +30V Sink Current 50mA Input Voltage (Note 2) +15V Power Dissipation (Note 3) 14 Ld DIP-Package 8 Ld Metal Can-Package 10 Ld Flatpack-Package 8 Ld DIP-Package Output Short Circuit Duration Maximum Strobe Current 10mA Operating Temperature Range -55 C to 125 C Thermal Resistance ThetaJA 14 Ld DIP 8 Ld Metal Can Pkg 10 Ld Flatpack 8 Ld DIP ThetaJC 14 Ld DIP 8 Ld Metal Can Pkg 10 Ld Flatpack 8 Ld DIP Storage Temperature Range Maximum Junction Temperature 175 C Lead Temperature (Soldering, 60 seconds) Voltage at Strobe Pin ESD Rating (Note 4) 300V 300 C V+ -5V
400mW 330mW 330mW 400mW
at at at at
25 25 25 25
C C C C
10 sec.
(Still Air (500LF/Min (Still Air (500LF/Min (Still Air (500LF/Min (Still Air (500LF/Min
@ 0.5W) Air flow @ 0.5W) Air flow @ 0.5W) Air flow @ 0.5W) Air flow
@ 0.5W) @ 0.5W) @ 0.5W) @ 0.5W)
TBD TBD 162 92 231 153 TBD TBD
C/W C/W C/W C/W
TBD 50 C/W 24 C/W TBD -65 C to 150 C
3
MJLM111-X REV 0C1
MICROCIRCUIT DATA SHEET
Note 1:
Note 2: Note 3:
Note 4:
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test conditions. This rating applies for +15V supplies. The positive input voltage limits is 30V above the negative supply. The negative input voltage limits is equal to the negative supply voltage or 30V below the positive supply, whichever is less. The maximum power dissipation must be derated at elevated temperatures and is dictated by Tjmax (maximum junction temperature), ThetaJA (package junction to ambient thermal resistance), and TA (ambient temperature). The maximum allowable power dissipation at any temperature is Pdmax = (Tjmax - TA)/ThetaJA or the number given in the Absolute Maximum Ratings, whichever is lower. Human body model, 1.5k Ohms in series with 100pF.
Recommended Operating Conditions
Supply Voltage Vcc = +15Vdc Amp Operating Temperature Range -55 C to +125 C
4
MJLM111-X REV 0C1
MICROCIRCUIT DATA SHEET
Electrical Characteristics
DC PARAMETERS
(The following conditions apply to all the following parameters, unless otherwise specified.) DC: +Vcc = +15V, Vcm = 0V SYMBOL Vio PARAMETER Input Offset Voltage CONDITIONS Vin = 0V, Rs = 50 Ohms NOTES PINNAME MIN -3 -4 +Vcc = 29.5V, -Vcc = -0.5V, Vin = 0V, Vcm = -14.5V, Rs = 50 Ohms +Vcc = 2V, -Vcc = -28V, Vin = 0V, Vcm = +13V, Rs = 50 Ohms +Vcc = +2.5V, -Vcc = -2.5V, Vin = 0V, Rs = 50 Ohms Vio(R) Raised Input Offset Voltage Vin = 0V, Rs = 50 Ohms -3 -4 -3 -4 -3 -4 -3 -4.5 +Vcc = 29.5V, -Vcc = -0.5V, Vin = 0V, Vcm = -14.5V, Rs = 50 Ohms +Vcc = 2V, -Vcc = -28V, Vin = 0V, Vcm = +13V, Rs = 50 Ohms Iio Input Offset Current Vin = 0V, Rs = 50K Ohms -3 -4.5 -3 -4.5 -10 -20 +Vcc = 29.5V, -Vcc = -0.5V, Vin = 0V, Vcm = -14.5V, Rs = 50K Ohms +Vcc = 2V, -Vcc = -28V, Vin = 0V, Vcm = +13V, Rs = 50K Ohms Iio(R) Raised Input Offset Current Input Bias Current Vin = 0V, Rs = 50K Ohms -10 -20 -10 -20 -25 -50 Iib+ Vin = 0V, Rs = 50K Ohms -100 -150 +Vcc = 29.5V, -Vcc = -0.5V, Vin = 0V, Vcm = -14.5V, Rs = 50K Ohms +Vcc = 2V, -Vcc = -28V, Vin = 0V, Vcm = +13V, Rs = 50K Ohms -150 -200 -150 -200 MAX +3 +4 +3 +4 +3 +4 +3 +4 +3 +4.5 +3 +4.5 +3 +4.5 +10 +20 +10 +20 +10 +20 +25 +50 0.1 0.1 0.1 0.1 0.1 0.1 UNIT mV mV mV mV mV mV mV mV mV mV mV mV mV mV nA nA nA nA nA nA nA nA nA nA nA nA nA nA SUBGROUPS 1 2, 3 1 2, 3 1 2, 3 1 2, 3 1 2, 3 1 2, 3 1 2, 3 1, 2 3 1, 2 3 1, 2 3 1, 2 3 1, 2 3 1, 2 3 1, 2 3
5
MJLM111-X REV 0C1
MICROCIRCUIT DATA SHEET
Electrical Characteristics
DC PARAMETERS(Continued)
(The following conditions apply to all the following parameters, unless otherwise specified.) DC: +Vcc = +15V, Vcm = 0V SYMBOL IibPARAMETER Input Bias Current CONDITIONS Vin = 0V, Rs = 50K Ohms NOTES PINNAME MIN -100 -150 +Vcc = 29.5V, -Vcc = -0.5V, Vin = 0V, Vcm = -14.5V, Rs = 50K Ohms +Vcc = 2V, -Vcc = -28V, Vin = 0V, Vcm = +13V, Rs = 50K Ohms Vo(STB) CMR Collector Output Voltage (ST) Common Mode Rejection Low Level Output Voltage Vin+ = Gnd, Vin- = 15V, Istb = -3mA, Rs = 50 Ohms -28V<-Vcc<-0.5V, Rs=50 Ohms, 2V<+Vcc<29.5V, Rs=50 Ohms, -14.5VVol
0.4 0.4 1.5 1.5 10 500 500 500 6 7
V V V V nA nA nA nA mA mA mA mA
Icc-
uV/ C 2 uV/ C 3 pA/ C 2 pA/ C 3
6
MJLM111-X REV 0C1
MICROCIRCUIT DATA SHEET
Electrical Characteristics
DC PARAMETERS(Continued)
(The following conditions apply to all the following parameters, unless otherwise specified.) DC: +Vcc = +15V, Vcm = 0V SYMBOL Ios PARAMETER Short Circuit Current CONDITIONS Vout = 5V, t < 10mS, Vin- = 0.1V, Vin+ = 0V Vout = 5V, t < 10mS, Vin- = 0.1V, Vin+ = 0V Vout = 5V, t < 10mS, Vin- = 0.1V, Vin+ = 0V Vio(adj)+ Input Offset Voltage (Adjustment) Input Offset Voltage (Adjustment) Voltage Gain (Emitter) Voltage Gain (Emitter) Vout = 0V, Vin = 0V, Rs = 50 Ohms NOTES 3, 5 3, 5 3, 5 3 5 PINNAME MIN MAX 200 150 250 UNIT mA mA mA mV SUBGROUPS 1 2 3 1
Vio(adj)-
Vout = 0V, Vin = 0V, Rs = 50 Ohms
3
-5
mV
1
Ave+
Rl = 600 Ohms
3, 6 3, 6
10 8 10 8
V/mV 4 V/mV 5, 6 V/mV 4 V/mV 5, 6
Ave-
Rl = 600 Ohms
3, 6 3, 6
AC PARAMETERS
(The following conditions apply to all the following parameters, unless otherwise specified.) AC: +Vcc = +15V, Vcm = 0 trLHC Response Time (Collector Output) Response Time (Collector Output) Vod(Overdrive) = -5mV, Cl = 50pF, Vin = -100mV Vod(Overdrive) = 5mV, Cl = 50pF, Vin = 100mV 4 4 4 4 300 640 300 500 nS nS nS nS 7, 8B 8A 7, 8B 8A
trHLC
7
MJLM111-X REV 0C1
MICROCIRCUIT DATA SHEET
Electrical Characteristics
DC PARAMETERS: DRIFT VALUES
(The following conditions apply to all the following parameters, unless otherwise specified.) DC: +Vcc = +15V, Vcm = 0V. "Delta calculations performed on JAN S and QMLV devices at group B, subgroup 5 only". SYMBOL Vio PARAMETER Input Offset Voltage CONDITIONS Vin = 0V, Rs = 50 Ohms +Vcc = 29.5V, -Vcc = -0.5V, Vin = 0V, Vcm = -14.5V, Rs = 50 Ohms +Vcc = 2V, -Vcc = -28V, Vin = 0V, Vcm = +13V, Rs = 50 Ohms Iib+ Input Bias Current Vin = 0V, Rs = 50K Ohms +Vcc = 29.5V, -Vcc = -0.5V, Vin = 0V, Vcm = -14.5V, Rs = 50K Ohms +Vcc = 2V, -Vcc = -28V, Vin = 0V, Vcm = +13V, Rs = 50K Ohms IibInput Bias Current Vin = 0V, Rs = 50K Ohms +Vcc = 29.5V, -Vcc = -0.5V, Vin = 0V, Vcm = -14.5V, Rs = 50K Ohms +Vcc = 2V, -Vcc = -28V, Vin = 0V, Vcm = +13V, Rs = 50K Ohms Icex Output Leakage Current Note 1: Note 2: Note 3: Note Note Note Note 4: 5: 6: 7: +Vcc = 18V, -Vcc = -18V, Vout = 32V NOTES PINNAME MIN -0.5 -0.5 -0.5 -12.5 -12.5 -12.5 -12.5 -12.5 -12.5 -5 MAX 0.5 0.5 0.5 12.5 12.5 12.5 12.5 12.5 12.5 5 UNIT mV mV mV nA nA nA nA nA nA nA SUBGROUPS 1 1 1 1 1 1 1 1 1 1
Istb = -2mA at -55 C. Calculated parameter. Use DC tape for Ios and Vio(adj), Ave+ and Ave- as indicated in TAPE NAME section of this JRETS. Uses AC tape and hardware. Actual min. limit used is 5mA due to test setup. Datalog reading in K = V/mV. Vid is voltage difference between inputs.
8
MJLM111-X REV 0C1
MICROCIRCUIT DATA SHEET
Graphics and Diagrams
GRAPHICS# 05172HRB2 05174HRC2 05284HRC2 05349HRE2 05445HRC 05652HRA2 09569HRC2 09570HRC2 H08CRF J08ARL J14ARH P000151A P000152A P000153A P000387A W10ARG DESCRIPTION METAL CAN (H), TO-99, 8LD .200 DIA P.C. (B/I CKT) CERPACK (W), 10 LEAD (B/I CKT) METAL CAN (H), TO-39, 3LD .200 DIA P.C. (B/I CKT) CERDIP (J), 14 LEAD (B/I CKT) CERDIP (J), 8 LEAD (B/I CKT) CERDIP (J), 8 LEAD (B/I CKT) CERPACK (W), 10 LEAD (B/I CKT) CERDIP (J), 14 LEAD (B/I CKT) METAL CAN (H), TO-99, 8LD, .200 DIA P.C. (P/P DWG) CERDIP (J), 8 LEAD (P/P DWG) CERDIP (J), 14 LEAD (P/P DWG) METAL CAN (H), TO-99, 8LD .200 DIA P.C.(PIN OUT) CERPACK (W), 10 LEAD (PIN OUT) CERDIP (J), 8 LEAD (PIN OUT) CERDIP (J), 14 LEAD (PINOUT) CERPACK (W), 10 LEAD (P/P DWG)
See attached graphics following this page.
9
V+
8
GROUND
1
7
OUTPUT
IN+
2
6
BALANCE/ STROBE
IN-
3 4
5
BALANCE
V-
JL111H 8 - PIN METAL CAN CONNECTION DIAGRAM TOP VIEW P000151A
MIL/AEROSPACE OPERATIONS 2900 SEMICONDUCTOR DRIVE SANTA CLARA, CA 95050
N
GND IN+ INN/C V-
1 2 3 4 5
10 9 8 7 6
V+ OUTPUT N/C BALANCE STROBE BALANCE
JL111W 10 - LEAD CERPACK CONNECTION DIAGRAM TOP VIEW P000152A
MIL/AEROSPACE OPERATIONS 2900 SEMICONDUCTOR DRIVE SANTA CLARA, CA 95050
N
GROUND IN+ INV-
1 2 3 4
8 7 6 5
V+ OUTPUT BALANCE/ STROBE BALANCE
JL111J-8 8 - LEAD DIP CONNECTION DIAGRAM TOP VIEW P000153A
MIL/AEROSPACE OPERATIONS 2900 SEMICONDUCTOR DRIVE SANTA CLARA, CA 95050
N
N/C GND IN+ INN/C VBALANCE
1 2 3 4 5 6 7
14 13 12 11 10 9 8
N/C N/C N/C V+ N/C OUTPUT BALANCE/ STROBE
JL111J 14 - LEAD DIP CONNECTION DIAGRAM TOP VIEW P000387A
N
MIL/AEROSPACE OPERATIONS 2900 SEMICONDUCTOR DRIVE SANTA CLARA, CA 95050
MJLM111-X REV 0C1
MICROCIRCUIT DATA SHEET
Revision History
Rev
0C1
ECN #
Rel Date
Originator
Rose Malone
Changes
Update MDS: MJLM111-X Rev. 0B0 to MJLM111-X Rev. 0C1. Updated Power Dissipation Condition, Added Thermal Data and Burn-In Ckts for all packages. Changed Pinout P000150A to P000387A to match Data Base.
M0003013 08/24/98
10

▲Up To Search▲

Price & Availability of NSC05334

	To Download NSC05334 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .