 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| TPA4861 Audio Power Amplifier Evaluation Module DATA MANUAL: SLOU004 Date: July 1997 IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE ("CRITICAL APPLICATIONS"). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER'S RISK. In order to minimize risks associated with the customer's applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TI's publication of information regarding any third party's products or services does not constitute TI's approval, warranty or endorsement thereof. Copyright (c) 1999, Texas Instruments Incorporated TRADEMARKS TI is a trademark of Texas Instruments Incorporated. Other brands and names are the property of their respective owners. Contents Abstract ......................................................................................................................... 7 I Quick Start Guide ...................................................................................................... 8 1. Layout Definition ...................................................................................................... 9 2. Operation................................................................................................................. 12 3. Input/Output Connections...................................................................................... 13 4. Specifications ......................................................................................................... 15 5. Layout...................................................................................................................... 16 6. Bill of Materials ....................................................................................................... 18 Figures Figure 1. Figure 2. Figure 3. Figure 4. TPA4861 Audio Amplifier EVM Circuit Component Placement........................... 9 TPA4861 EVM Schematic................................................................................ 13 Input/Output Connections................................................................................. 14 TPA4861 Circuit Application Hookup Diagram, SE Drive ................................. 15 If You Need Assistance If You need Assistance... If You Want to... Do This... Request more information about Call the PIC| hotline: Texas instruments Mixed Signal (972) 644-5580 Products or send a fax to the PIC: (972) 480-7800 or write to: Texas Instruments Incorporated Product Information Center, MS 3123 P.O. Box 660246 Dallas, Texas 75266 Order Texas Instruments documentation Ask questions about product operation or report suspected problems Report mistakes in this Marketing document or any other TI Correction: Mixed Signal Products documentation Call the PIC| hotline: (972) 644-5580 Call the PIC| hotline: (972) 644-5580 Send a fax to MSP Documentation (214) 480-3160 or send your comments to: Texas Instruments Incorporated MSP Marketing Documentation Correction, MS 8710 P.O. Box 660199 Dallas, Texas 75266-0199 | Texas Instruments Product Information Center TPA4861 Audio Power Amplifier Evaluation Module Abstract The Texas Instruments (TITM) TPA4861 audio power amplifier sample evaluation module (EVM) (SLOP099) incorporates the circuitry required for designers of notebook, cellular, and other hand-held audio systems to evaluate the performance of the TPA4861 audio power amplifier without investing in a PC board layout and assembly (see the application note in the TPA4861 data sheet (SLOS163) for a description of the circuit configuration and selection of components). The TPA4861 EVM plugs into TI's Plug-N-Play Audio Amplifier Evaluation Platform (SLOP097). The platform is a convenient evaluation vehicle incorporating the required circuitry to power and test all of its compatible audio power amplifier EVMs and thus eliminate the need for external implementation. The TPA4861 EVM can be used with the TPA4860 EVM (SLOP098) to derive various drive configurations. Operating the TPA4861 Audio Power Amplifier Sample EVM (SLOP099) 7 I. Quick Start for P-N-P Kit Included below is a quick checklist of setup steps to get the TPA4861 up and running fast. 1. Set S1 to the "off" position. 2. Align the TPA4861 with either socket U3 or U4, such that the side with 4 pins is adjacent to the speaker connections, and firmly connect it to the P-n-P board. 3. Check the power supply jumper setting on the P-n-P board. To use battery power select JP3, to select wall mount AC/DC power select JP2, or to use a bench type DC power supply select JP1 Note: be sure only one of these three jumpers is connected by a shorting block. 4. Check the mode/mute jumper circuitry (JP6, JP7, JP8). To begin with, set JP7 to Lo, JP8 to Hi, and JP6 to Mode. This arrangement causes the TPA4861 to be active when no headphones are present. In the future refer to Table 1 in the P-n-P board Application Report (SLOU001) to adjust these settings. 5. Check the Audio Input Path Selection Circuitry, if there is no EVM present in U1, then set S2 to the "off" position 6. Set S3 to the "U5" position. (only if headphone EVM is connected to U5) 7. Connect a mono audio source to either J3 or J5 (or both), or connect a stereo audio source to J4. 8. Connect a 8 ohm speaker(s) to either (or both of) the RCA jacks at J7 (U3) and J9 (U4) or to the wire clips at J8. 9. Connect your power supply to the P-n-P board. 10. Push S1 to the "on" position. Activate the audio source. Step 10 will activate the EVMs present on the P-n-P. If you do not hear sound, please consult the troubleshooting section of the P-n-P Board application report (SLOU001). To use power from J1, J2, or B1 a DC/DC converter must be used at U6. If no converter is present, use DC power at J6. 8 SLOU004 1. Layout Definition The TPA4861 is a CMOS device designed primarily for bridge tied load (BTL) operation (please consult the TPA4861 data sheet, SLOS163) in notebook, cellular, and other hand-held audio systems. The typical supply current of 3.5 mA at 5 V makes the TPA4861 an ideal upgrade for battery powered applications. Figure 1 shows The TPA4861 audio amplifier EVM layout. Figure 1. TPA4861 Audio Amplifier EVM Circuit Component Placement Shutdown S1 R1 +5V GND R5 + C6 C3 C5 DL OUT- 4861 C2 R2 C1 IN+ GND U1 C4 R3 GND OUT+ R4 TPA4861 Sample EVM Operating the TPA4861 Audio Power Amplifier Sample EVM (SLOP097) 9 4861 U1 - TPA4861D, Mono 1 W Audio Amplifier C1 - Capacitor, 1.0 F Ceramic C2, C3 - Capacitor, 2.2 F Ceramic C4 - Capacitor, 5 pF Ceramic C5 - Capacitor, 0.1 F Ceramic C6 - Capacitor, 10 F Electrolytic R1, R2, R3 - Resistor, 20 k Carbon R4 - Potentiometer, 200 k 3/4 Turn R5 - Resistor, 51 Carbon S1, - Switch, Normally Open, Momentary The TPA4861 sample EVM offers the following key features: u Mono Bridge Tied Load (BTL) drive for 8 ohm speakers and above Shutdown input Controlled from an external TTL source or a switch to mute the speakers and place the IC in an ultra-low current mode. u u Gain Control Pot R4 Lower gains produce better distortion performance (see the TPA4861 data sheet for more information). Gain vs total harmonic distortion (THD) should be considered in each application. The gain adjustment range on the EVM is 2 to 22. NOTE: Most speakers have significantly worse distortion than the TPA4861 at high gain settings. The connection pins of the TPA4861 EVM are on a 0.1" grid for easy interface to standard plugboard-based prototype systems. For higher temperature applications, the TPA4861 sample EVM is packaged in an 8-pin ssmall-outline integrated circuit (SOIC) that provides a thermal connection to the PC copper area for better heat dissipation. The TPA4861 offers an 8-pin SOIC package that is adequate for most room-temperature applications. 10 SLOU004 The thermal layout of the EVM is important because linear audio power amplifiers dissipate large amounts of heat during operation (see the TPA4861 data sheet (SLOS163) for details on heat dissipation for 5 V and 3.3 V applications). All GND pins must be connected to as much copper area as possible on the surface of the PC board. These copper areas should then be connected with vias to ground plane layers inside the PC board. These connections become even more important in high ambient temperature applications. Operating the TPA4861 Audio Power Amplifier Sample EVM (SLOP097) 11 2. Operation The TPA4861 EVM is compatible with the TI Plug-N-Play Audio Amplifier Evaluation Platform slots U3 and U4. No soldering is required for use in the plug-and-play (PnP) system. The evaluation platform includes standard speaker jacks, RCA jacks, and 1/8" stereo input jacks for quick and easy evaluation of all TI TPA series audio power amplifiers. The TPA302 EVM (SLOP100) is recommended for use as the headphone drive. For standalone use, connections diagrams are shown in figures 3 and 4. 12 SLOU004 3. Input/Output Connections Figure 2. TPA4861 EVM Schematic Vdd 2.7 to 5.5 V GND S1 Shutdown (+ VDD to Mute) no 1 Shutdown Vo - 8 C6 R5 10 uF 50 C5 0.1 uF Dummy Load (SE) OUT - R1 20 k C1 1 uF Audio Input + Audio Input - C2 1 uF 2 Bypass GND 7 3 IN + VDD 6 C3 1 uF GND OUT + 4 IN - Vo + 5 R2 20 k R3 20 k R4 200 k C4 5 pF Figure 3 shows the TPA4861 connections diagram for the BTL drive configuration. The BTL configuration eliminates the large output coupling capacitors and quadruples the available output power when compared to single-ended (SE) solutions. As a result, the total PC board space required is much smaller than SE configurations of the same output power. Figure 3. TPA4861 EVM Input/Output Connections - BTL Drive Operating the TPA4861 Audio Power Amplifier Sample EVM (SLOP097) 13 Figure 4 shows two TPA4861 EVMs configured to drive stereo speakers. A standard 1/8" stereo input jack provides a convenient connection to CD players and other commercial sources of audio signals. TPA4861 Sample EVM Circuit Application Hookup Diagram, BTL Drive 3.3 V to 5.0 V DC 03/10/97 + Power Supply C1 10 uF Shutdown S1 R1 +5V GND R5 - + C6 C3 C5 DL OUTGND OUT+ 4861 C2 R2 C1 IN+ GND U1 C4 R3 R4 TPA4861 Sample EVM EVM1 Shutdown S1 R1 4861 +5V GND R5 W1 + C6 C3 C5 DL OUTGND OUT+ Audio Input C2 R2 C1 IN+ GND U1 C4 R3 R4 TPA4861 Sample EVM Standard 1/8" Stereo Jack EVM2 Figure 3. TPA4861 Circuit Applications Connections Diagram - BTL Drive The stereo SE drive configuration requires the output from Out- to be connected to the Dummy Load (DL) input to prevent the unused output from becoming unstable and possibly oscillating during operation. Oscillations cause unwanted noise that can couple into other circuits (see the TPA460 data sheet for details). Output power using stereo SE drive is reduced by a factor of four (see the TPA4861 data sheet for details of the tradeoffs between BTL and SE operation). To prevent DC currents from flowing into the speakers, output coupling caps are required in SE mode. 14 SLOU004 Figure 4. TPA4861 Circuit Application Connections Diagram, SE Drive TPA4861 Sample EVM Circuit Application Hookup Diagram, SE Drive 3.3 V to 5.0 V DC 03/10/97 + Power Supply C1 10 uF Shutdown S1 R1 +5V GND R5 - + C6 C3 C5 DL OUTGND OUT+ 4861 C2 R2 C1 IN+ GND U1 C4 R3 R4 TPA4861 Sample EVM EVM1 Shutdown S1 R1 4861 +5V GND R5 W1 + C6 C3 C5 DL OUTGND OUT+ Audio Input C2 R2 C1 IN+ GND U1 C4 R3 R4 TPA4861 Sample EVM Standard 1/8" Stereo Jack EVM2 4. Specifications Power 2.7 to 5.5 Vdc, 500 mA max. Audio Input Mono, Cap Coupled (1.0 F), 4 Vpp Max @ G = 1 Speaker Outputs BTL 8 ohm drive, 1 W rms continuous SE 8 ohm drive, 250 mW rms continuous SE 32 ohm drive, 70 mW rms continuous Dummy Load Input (DL) Recommended tie to Out- when operating in SE mode Shutdown Input/Switch High places amplifier in ultra-low current state. Outputs are muted. Switch is a momentary action push button. Press to mute. R4 Gain Control Pot 3/4 turn adjusts amplifier gain from 2 to 20 BTL, 1 to 10 SE. Clockwise increases gain. Operating the TPA4861 Audio Power Amplifier Sample EVM (SLOP097) 15 5. Layout NOTE: Layouts are not to scale. 16 SLOU004 \ NOTE: Layouts are not to scale. Operating the TPA4861 Audio Power Amplifier Sample EVM (SLOP097) 17 6. Bill of Materials Description Pot., 200 K Ohm Cermet ST SL, Thru Hole Cap., 10 F/6.3 V, SMD, Size "A" Cap., 1.0 F, +80/-20%, NonPolarized, SMD Size 1206 Cap., 2.2 F,20%, Non-Polarized, SMD Size 1206 Cap., .1 F/16 V, SMD, Size 1206 Cap, 5.0 pF, SMD, Size 0805 Res., 20 K Ohm, 1/8 W, 5%, SMD, Size 1206 Res., 510 Ohm, 1/8 W, SMD, Size 1206 Switch, Momentary, SMD IC., TPA4861, Audio Amplifier, 1 W, Mono,SMD, SOIC-8 PCB, TPA4681 Sample EVM Ref R4 C6 C1 C2,C3 C5 C4 R1, R2, R3 R5 S1 U1 PCB1 PCBA Manufacturer Qty Part Number 1 Bourns 3323P-1-204 1 Panasonic ECS-TOJY106R 1 Murata GRM42-6Y5V105Z16BL 2 TDK C3216X5R1A225 1 Panasonic ECS-H1CY105R 1 Panasonic ECU-V1H050CCN 3 Panasonic ERJ-8GEYJ203 1 Panasonic ERJ-8GEYJ511 1 Panasonic P8048SCT-ND 1 TI TPA4860 1 Compuroute Tool Digi-Key Part Number Digi-Key 3323P-204-ND Digi-Key PCS1106CT-ND Newark 93F2254 Digi-Key PCT104BCT-ND Digi-Key PCC050CNCT-ND Digi-Key P20KECT-ND Digi-Key P510ECT-ND Digi-Key P8048SCT-ND 18 SLOU004 |
Price & Availability of SLOU004
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |