 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Preliminary PLL103-06 DDR SDRAM Buffer with 2 DDR or 3 SDRAM DIMMS FEATURES * * * * * * * * * Generates 12-output buffers from one input. Supports up to 2 DDR DIMMS or 3 SDRAM DIMMS. Supports 266MHz DDR SDRAM. One additional output for feedback. Less than 5ns delay. Skew between any outputs is less than 100 ps. 2.5V or 3.3V Supply range. Enhanced DDR and SDRAM Output Drive selected by I2C. Available in 28 pin SSOP. PIN CONFIGURATION FBOUT PD# DDR0T_SDRAM0 DDR0C_SDRAM1 VDD3.3_2.5 GND DDR1T_SDRAM2 DDR1C_SDRAM3 VDD3.3_2.5 BUF_IN GND DDR2T_SDRAM4 DDR2C_SDRAM5 VDD3.3_2.5 DDR0T_SDRAM0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 28 27 26 25 24 23 22 21 20 19 18 17 16 15 SEL_DDR DDR5T_SDRAM10 DDR5C_SDRAM11 VDD3.3_2.5 GND DDR4T_SDRAM8 DDR4C_SDRAM9 VDD3.3_2.5 GND DDR3T_SDRAM6 DDR3C_SDRAM7 GND SCLK SDATA PLL103-06 BLOCK DIAGRAM Note: #: Active Low SDATA SCLK PD# I2C Control DDR0C_SDRAM1 DDR1T_SDRAM2 DDR1C_SDRAM3 DDR2T_SDRAM4 DDR2C_SDRAM5 DESCRIPTIONS The PLL103-06 is designed as a 3.3V/2.5V buffer to distribute high-speed clocks in PC applications. The device has 12 outputs. These outputs can be configured to support 3 unbuffered standard SDR (Single Data Rate) DIMMS and 2 DDR DIMMS. The PLL103-06 can be used in conjunction with the PLL202-04 or similar clock synthesizer for the VIA Pro 266 chipset. The PLL103-06 also has an I2C interface, which can enable or disable each output clock. When power up, all output clocks are enabled (has internal pull up). BUF_IN DDR3T_SDRAM6 DDR3C_SDRAM7 DDR4T_SDRAM8 DDR4C_SDRAM9 DDR5T_SDRAM10 DDR5C_SDRAM11 FBOUT SEL_DDR 47745 Fremont Blvd., Fremont, California 94538 TEL (510) 492-0990 FAX (510) 492-0991 Rev 12/20/00 Page 1 Preliminary PLL103-06 DDR SDRAM Buffer with 2 DDR or 3 SDRAM DIMMS PIN DESCRIPTIONS Name FBOUT BUF_IN PD Number 1 10 2 Type O I I Description Feedback clock for chipset. Output voltage depends on VDD3.3_2.5V. Reference input from chipset. 3.3V input for STANDARD SDRAM mode; 2.5V input for DDR-ONLY mode. Power Down Control input. When low, it will tri-state all outputs. SEL_DDR 28 I Input configure for DDR-ONLY mode or STANDARD SDR mode. 1 = DDR-ONLY mode (when VDD3.3_2.5 select 2.5V); 0 = SDR mode (when VDD3.3_2.5 select 3.3V). In DDR-ONLY mode, all outputs will be configured as DDR outputs. In STANDARD SDR mode, all outputs will be configured as SDRAM outputs. When SEL_DDR=1, these outputs provide DDR mode outputs; when SEL_DDR=0, these outputs provide standard SDRAM mode outputs. Voltage swing depends on VDD3.3_2.5. When SEL_DDR=1, these outputs provide complementary copies of BUF_IN; when SEL_DDR=0, these outputs provide standard SDRAM mode outputs. Voltage swing depends on VDD3.3_2.5. When VDD=2.5V, SEL_DDR=1. DDR-ONLY mode is selected; when VDD=3.3V, SEL_DDR=0. STANDARD SDRAM mode is selected. Ground. DDR[0:5]T_SDRAM [0,2,4,6,8,10] DDR[0:5]C_SDRAM [1,3,5,7,9,11] VDD3.3_2.5 GND 3,7,12,19, 23,27 4,8,13,18, 22,26 5,9,14,21,25 6,11,17, 20,24 O O P P 47745 Fremont Blvd., Fremont, California 94538 TEL (510) 492-0990 FAX (510) 492-0991 Rev 12/20/00 Page 2 Preliminary PLL103-06 DDR SDRAM Buffer with 2 DDR or 3 SDRAM DIMMS I2C BUS CONFIGURATION SETTING Address Assignment Slave Receiver/Transmitter Data Transfer Rate A6 1 A5 1 A4 0 A3 1 A2 0 A1 0 A0 1 R/W _ Provides both slave write and readback functionality Standard mode at 100kbits/s This serial protocol is designed to allow both blocks write and read from the controller. The bytes must be accessed in sequential order from lowest to highest byte. Each byte transferred must be followed by 1 acknowledge bit. A byte transferred without acknowledged bit will terminate the transfer. The write or read block both begins with the master sending a slave address and a write condition (0xD2) or a read condition (0xD3). Following the acknowledge of this address byte, in Write Mode: the Command Byte and Byte Count Byte must be sent by the master but ignored by the slave, in Read Mode: the Byte Count Byte will be read by the master then all other Data Byte. Byte Count Byte default at power-up is = (0x09). Data Protocol I2C CONTROL REGISTERS 1. BYTE 6: Outputs Register (1=Enable, 0=Disable) Bit Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Pin# 28 1 27, 26 23, 22 - Default 1 0 0 1 1 1 1 1 Description SEL_DDR ( I2C is ready only, value is set through pin28 ) Reserved Reserved FBOUT DDR5T_SDRAM10, DDR5C_SDRAM11 Reserved DDR4T_SDRAM8, DDR4C_SDRAM9 Reserved 47745 Fremont Blvd., Fremont, California 94538 TEL (510) 492-0990 FAX (510) 492-0991 Rev 12/20/00 Page 3 Preliminary PLL103-06 DDR SDRAM Buffer with 2 DDR or 3 SDRAM DIMMS 2. BYTE 7: Outputs Register (1=Enable, 0=Disable) Bit Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Pin# 19, 18 12, 13 7, 8 3, 4 Default 1 1 1 1 1 1 1 1 Description Reserved DDR3T_SDRAM6, DDR3C_SDRAM7 DDR2T_SDRAM4, DDR2C_SDRAM5 Reserved Reserved DDR1T_SDRAM2, DDR1C_SDRAM3 Reserved DDR0T_SDRAM0, DDR0C_SDRAM1 47745 Fremont Blvd., Fremont, California 94538 TEL (510) 492-0990 FAX (510) 492-0991 Rev 12/20/00 Page 4 Preliminary PLL103-06 DDR SDRAM Buffer with 2 DDR or 3 SDRAM DIMMS ELECTRICAL SPECIFICATIONS 1. Absolute Maximum Ratings PARAMETERS Supply Voltage Input Voltage, dc Output Voltage, dc Storage Temperature Ambient Operating Temperature ESD Voltage SYMBOL V DD VI VO TS TA MIN. V SS -0.5 V SS -0.5 V SS -0.5 -65 0 MAX. 7.0 V DD +0.5 V DD +0.5 150 70 2 UNITS V V V C C KV Exposure of the device under conditions beyond the limits specified by Maximum Ratings for extended periods may cause permanent damage to the device and affect product reliability. These conditions represent a stress rating only, and functional operations of the device at these or any other conditions above the operational limits noted in this specification is not implied. 2. Operating Conditions PARAMETERS Supply Voltage Supply Voltage Input Capacitance Output Capacitance SYMBOL V DD3.3 V DD2.5 CIN COUT MIN. 3.135 2.375 MAX. 3.465 2.625 5 6 UNITS V V pF pF 3. Electrical Specifications PARAMETERS Input High Voltage Input Low Voltage Input High Current Input Low Current Output High Voltage Output Low Voltage Output High Current Output Low Current Note: TBM: To be measured SYMBOL V IH V IL I IH I IL V OH V OL I OH I OL CONDITIONS All Inputs except I2C All inputs except I2C V IN = V DD V IN = 0 IOL = -12mA, IOL = 12mA, VDD = 2.375V VDD = 2.375V MIN. 2.0 VSS-0.3 TYP. MAX. VDD+0.3 0.8 TBM TBM UNITS V V uA uA V 1.7 0.6 -18 26 -32 35 V mA mA VDD = 2.375V, VOUT=1V VDD = 2.375V, VOUT=1.2V 47745 Fremont Blvd., Fremont, California 94538 TEL (510) 492-0990 FAX (510) 492-0991 Rev 12/20/00 Page 5 Preliminary PLL103-06 DDR SDRAM Buffer with 2 DDR or 3 SDRAM DIMMS 3. Electrical Specifications (Continued) PARAMETERS Supply Current (DDR-only mode) Supply Current (SDRAM mode) Supply Current Output Crossing Voltage Output Voltage Swing Duty Cycle Max. Operating Frequency Rising Edge Rate Falling Edge Rate DDR Rising Edge Rate DDR Falling Edge Rate Clock Skew(pin to pin) Stabilization Time Note: TBM: To be measured SYMBOL IDD IDD IDDS VOC VOUT DT CONDITIONS Unloaded outputs, 133MHz Unloaded outputs, 133MHz PD = 0 MIN. TYP. MAX. TBM TBM TBM UNITS mA mA mA V V % MHz V/ns V/ns V/ns V/ns ps ms (VDD/2) -0.1 0.7 Measured @ 1.5V 45 66 VDD/2 (VDD/2)+ 0.1 VDD-0.4 55 170 50 TOR TOF TOR TOF TSKEW TST Measured @ Measured @ 0.4V ~ 2.4V 2.4V ~ 0.4V 1.0 1.0 0.25 0.25 1.5 1.5 0.6 0.6 2.0 2.0 1.0 1.0 100 0.1 Measured between 20% to 80% of output Measured between 20% to 80% of output All outputs equally loaded 47745 Fremont Blvd., Fremont, California 94538 TEL (510) 492-0990 FAX (510) 492-0991 Rev 12/20/00 Page 6 Preliminary PLL103-06 DDR SDRAM Buffer with 2 DDR or 3 SDRAM DIMMS PACKAGE INFORMATION 0.301 - 0.311 7.645 - 7.899 0.205- 0.212 5.207 - 5.385 0.010 - 0.015 0.254 - 0.381 0.015 (0.381) 0.005 - 0.008 (0.127 - 0.203) 45 0 0.396 - 0.407 (10.06 - 10.33) 0.0256 0.6502 0.066 - 0.070 (1.676 - 1.778) 0.068 - 0.078 (1.727 - 1.981) 00-8 0 0.022 - 0.037 (0.55 - 0.95) 0.002 - 0.008 (0.0508- 0.2032) 28 PIN SSOP ORDERING INFORMATION For part ordering, please contact our Sales Department: 47745 Fremont Blvd., Fremont, CA 94538, USA Tel: (510) 492-0990 Fax: (510) 492-0991 The order number for this device is a combination of the following: Device number, Package type and Operating temperature range PART NUMBER PLL103-06 X C PART NUMBER TEMPERATURATURE C=COMMERCIAL M=MILITARY I=INDUSTRAL PACKAGE TYPE X=SSOP PhaseLink Corporation, reserves the right to make changes in its products or specifications, or both at any time without notice. The information furnished by PhaseLink is believed to be accurate and reliable. However, PhaseLink makes no guarantee or warranty concerning the accuracy of said information and shall not be responsible for any loss or damage of whatever nature resulting from the use of, or reliance upon this product. LIFE SUPPORT POLICY: PhaseLink's products are not authorized for use as critical components in life support devices or systems without the express written approval of the President of PhaseLink Corporation. 47745 Fremont Blvd., Fremont, California 94538 TEL (510) 492-0990 FAX (510) 492-0991 Rev 12/20/00 Page 7 |
Price & Availability of PLL103-06
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |