|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
HDSP-815E/816E/815G/816G 20 mm (0.8 inch) General Purpose Seven Segment Displays Data Sheet Description These 20 mm (0.8 inch) displays use industry standard size and pin-out. The devices are available as either common anode or common cathode. Available in either red or green colors, these gray-faced displays are suitable for indoor use. No color binning is offered for these parts. These parts are subjected to Outgoing Quality Assurance (OQA) inspection with AQL of 0.065% for functional and visual/cosmetic rejects. Devices HER HDSP815E 816E Features * Industry standard size * Industry standard pin-out 15.24 mm (0.6 in.) DIP leads on 2.54 mm (0.1 in.) centers * Choice of colors Red, Green * Mitered font Mitered corners on segments * Gray face paint Gray package gives optimum contrast * 50 Viewing angle * Design flexibility Common anode or common cathode * Categorized for luminous intensity Applications * Suitable for indoor use * Not recommended for industrial applications, i.e., operating temperature requirements exceeding 85C or below -25C[1] * Extreme temperature cycling not recommended[2] Green HDSP815G 816G Description Common Anode Right Hand Decimal Common Cathode Right Hand Decimal Notes: 1. For industrial applications, it is recommended to use HDSP-3901/ 3903/8601/8603. 2. For details, please contact your local Avago Technologies sales office or an authorized distributor. Part Numbering System 5082 -X X X X-X X X X X HDSP-X X X X-X X X X X Mechanical Options[1] 00: No Mechanical Option Color Bin Options[1,2] 0: No Color Bin Limitation Maximum Intensity Bin[1,2] 0: No Maximum Intensity Bin Limitation Minimum Intensity Bin[1,2] 0: No Minimum Intensity Bin Limitation Device Configuration/Color[1] E: High Efficiency Red G: Green Device Specific Configuration[1] Refer to Respective Datasheet Package[1] Refer to Respective Datasheet Notes: 1. For codes not listed in the figure above, please refer to the respective datasheet or contact your nearest Avago representative for details. 2. Bin options refer to shippable bins for a part number. Color and Intensity Bins are typically restricted to 1 bin per tube (exceptions may apply). Please refer to respective datasheet for specific bin limit information. 2 Package Dimensions 11.07 (0.436) 8 LUMINOUS INTENSITY CATEGORY 1 16 13.08 (0.514) 4.60 (0.181) 20.32 (0.800) HDSP-XXXX XYY Z XXXX 1.70 (0.067) 27.69 0.25 (1.090 0.010) DIA. 0.50 (0.020) 2.54 x 7 = 17.78 (0.100 x 7 = 0.700) 6 9 UNUSED DP 1.25 (0.049) 8.20 (0.323) C L C L CHARACTER PACKAGE RHDP DATE CODE COUNTRY OF ORIGIN SIDE VIEW FRONT VIEW NOTES: 1. DIMENSIONS IN MILLIMETERS AND (INCHES). 2. TOLERANCE IS 0.25 mm (0.010 INCH) UNLESS OTHERWISE STATED. 19.96 (0.786) 8.38 (0.330) 4.8 0.50 (0.189 0.020) 15.24 (0.600) END VIEW 3 Internal Circuit Diagram COMMON ANODE PIN 1 1 2 3 4 5 6 7 8 d DP e c f b g a 16 15 14 13 12 11 10 9 1 2 3 4 5 6 7 8 d DP e c f b g a 2 16 15 14 13 12 11 10 9 3 4 5 6 7 8 9 10 11 12 13 14 15 16 FUNCTION CATHODE A CATHODE F COMMON ANODE CATHODE E COMMON ANODE NO CONNECTION NO PIN NO PIN CATHODE RHDP CATHODE D COMMON ANODE CATHODE C CATHODE G CATHODE B NO PIN COMMON ANODE PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 COMMON CATHODE FUNCTION ANODE A ANODE F COMMON CATHODE ANODE E COMMON CATHODE NO CONNECTION NO PIN NO PIN ANODE RHDP ANODE D COMMON CATHODE ANODE C ANODE G ANODE B NO PIN COMMON CATHODE COMMON ANODE COMMON CATHODE 4 Absolute Maximum Ratings at TA=25C High Efficiency Red HDSP-815E HDSP-816E 62.5 100 25 3 -25 to +85 -25 to +85 250 Green HDSP-815G HDSP-816G 65 90 25 3 -25 to +85 -25 to +85 250 Parameter Average Power per Segment or DP Peak Forward Current per Segment or DP (1/10 Duty Cycle, 0.1 ms Pulse Width) DC Forward Current per Segment or DP[1] Reverse Voltage per Segment or DP Operating Temperature Storage Temperature Wave Soldering Temperature for 3 Seconds[2] (1.6 mm [0.063 in.] below Body) Units MW mA mA V C C C Notes: 1. Derate above 25C at 0.33 mA/C. 2. Not recommended to be soldered more than 2 times. Minimum interval between solderings is 15 minutes. Total soldering time not to exceed 5 seconds. Optical/Electrical Characteristics at TA=25C High Efficiency Red Devices HDSPParameter Luminous Intensity/Segment (Segment Average)[1,2] Forward Voltage/Segment or DP Peak Wavelength Dominant Wavelength[3] Reverse Voltage/Segment or DP[4] Temperature Coefficient of VF/Segment or DP Symbol Iv VF PEAK d Min. 2.3 Typ. 4.8 2.1 635 626 25 -2 Max. Units mcd V nm nm V mV/C Test Conditions IF = 20 mA IF = 20 mA 3.0 815E 816E VR VF/C 3.0 IR = 100 A Green Devices HDSPParameter Luminous Intensity/Segment (Segment Average)[1,2] Forward Voltage/Segment or DP Peak Wavelength Dominant Wavelength[3] Reverse Voltage/Segment or DP[4] Temperature Coefficient of VF/Segment or DP Symbol Iv VF PEAK d Min. 1.5 Typ. 3.3 2.1 566 571 50 -2 Max. Units mcd V nm nm V mV/C Test Conditions IF = 20 mA IF = 20 mA 2.6 815G 816G VR VF/C 3.0 IR = 100 A Notes: 1. Case temperature of the device immediately prior to the intensity measurement is 25C. 2. The digits are categorized for luminous intensity. The intensity category is designated by a letter on the side of the package. 3. The dominant wavelength, d, is derived from the CIE chromaticity diagram and represents the single wavelength which defines the color of the device. 4. Typical specification for reference only. Do not exceed absolute maximum ratings. 5 DC MAX - MAXIMUM DC CURRENT PER SEGMENT - mA 40 35 RJA = 525C/W IF - FORWARD CURRENT PER SEGMENT - mA 100 30 25 20 GREEN, HER 80 60 15 10 5 0 10 20 30 40 50 60 70 80 90 100 TA - AMBIENT TEMPERATURE - C 40 GREEN HER 0 0 1 2 3 4 5 20 VF - FORWARD VOLTAGE Figure 1. Maximum allowable DC current vs. ambient temperature. Figure 2. Forward current vs. forward voltage. 2.00 RELATIVE LUMINOUS INTENSITY (NORMALIZED TO 1 AT 20 mA) 1.75 1.50 1.25 1.00 0.75 HER 0.50 0.25 0 0 10 20 30 40 GREEN Intensity Bin Limits (mcd at 20 mA) HER/Green Green Bin Name N P Q R Min.[1] NA 7.57 10.78 15.10 Max.[1] NA 10.78 15.10 21.58 Min.[1] 5.31 7.57 10.78 NA HER Max.[1] 7.57 10.78 15.10 NA IF - FORWARD CURRENT PER SEGMENT - mA Color Categories Figure 3. Relative luminous intensity vs. DC forward current. Dominant Wavelength (nm) Color Green Bin 1 2 Min. 569.00 572.00 Max. 572.00 575.00 Note: 1. All categories are established for classification of products. Products may not be available in all categories. Please contact your Avago representative for further clarification/information. 6 Contrast Enhancement For information on contrast enhancement, please see Application Note 1015. Soldering/Cleaning Cleaning agents from the ketone family (acetone, methyl ethyl ketone, etc.) and from the chlorinated hydrocarbon family (methylene chloride, trichloroethylene, carbon tetrachloride, etc.) are not recommended for cleaning LED parts. All of these various solvents attack or dissolve the encapsulating epoxies used to form the package of plastic LED parts. For information on soldering LEDs please refer to Application Note 1027. Device Reliability For reliability information, please see the reliability data sheet 20 mm (0.8 inch) General Purpose Seven Segment Display. 7 For product information and a complete list of distributors, please go to our website: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies, Pte. in the United States and other countries. Data subject to change. Copyright (c) 2006 Avago Technologies Pte. All rights reserved. Obsoletes 5988-4353EN 5988-7999EN April 17, 2006 |
Price & Availability of HDSP-815E |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |