 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| MOSEL VITELIC INC. Preliminary MSS0271 2.7" VOICE ROM May 1997 Features Single power can operate at 2.4 V through 6 V. Current output can directly drive either buzzer or speaker without a transistor. Built-in Oscillating Resistor. Single section, 2.79 seconds (4380h). Speech with mute (behind) is up to 21.1 seconds (20000h). Repeat function that can repeat up to 8 times. To turn on LED in sink connection. Automatic power down. CDS interface is provided. Mask options Either level or edge trigger type at pin TG. Either LED flasher or BUSY output at pin LED/BZ. Either 6200Hz or 8400Hz S.R. for built-in Rosc. Either holdable output or not. Either retriggerable output or not. Either fixed or dynamic type on LED flasher. Either 3Hz or 6Hz LED fixed flasher, (S.R. dependent). Either Fast or Slow debounce time. General Description The MSS0271 is a single-chip CMOS LSI demands minimal external components and memorizes voice up to 2.88 seconds (at 6 KHz S.R.) using the MOSEL qualified coding method (MPCM-4). The chip contains most of the necessary circuit like oscillator, PLA, D/A converter, buzzer buffer, control and timing logic. Therefore, it can apply to various voice systems with minimum external parts. Customer speech data will be edited and programmed into PLA by changing one mask during the device fabrication. Block Diagram Vdd OSCILLATOR VSS ADDRESS GENERATOR PLA D/A SP1 SP2 IN1 IN0 TG CONTROL LOGIC LB Specifications subject to change without notice, contact your sales representatives for the most recent information. 1/12 PID257*** 05/97 MOSEL VITELIC INC. Preliminary MSS0271 Pad Description P20 COB pin # 1 3 5 7 14 15 16 17 18 P28 COB pin # 1 3 7 11 19 21 23 24 26 Pad# 1 2 3 4 5 6 7 8 9 Symbol TG LB IN0 IN1 NC SP2 Vss SP1 Vdd o o Active high i/o i o i i/o Names trigger to play sound, internal pull low LED flasher output or high true Busy signal output input control 0 input control 1 no connection speaker drive 2 ground speaker drive 1 positive power supply Absolute Maximum Rating Symbol VDD ~ VSS VIN (TG) VOUT (STP) T (Operating) T (Storage) FOSC Characteristics Unit V V V C C 8000 Max 6000 Min 4000 2000 Hz 2.0 3.0 Mask = 6200Hz Min. -10 2.4 typ. Max 60 6.0 Unit C V Hz Remarks 4.0 5.0 6.0 Vdd 5500 6700 Rating -0.5 ~ +7.0 VSS -0.3 < V IN < VDD+0.3 VSS Operating Conditions Symbol TA VCC SR Description Ambient temperature under bias supply voltage sample rate 6200 or 8400 AC Characteristics at 4.5 V, 6200 Hz SR Symbol T T1 T T2 T T T T T T T T T T T T T T T PUD THLO THZH THAS TLLF TLZL THAE AELF AEZL IWR1 IWR2 LED3 LED6 P R Parameter trigger pulse width trigger pulse width power up delay trigger high to LED on trigger high to busy high trigger high to audio start trigger low to LED off trigger low to busy low trigger low to audio end audio end to LED off audio end to busy low interval when repeat interval when repeat LED on time at 3 Hz LED on time at 6 Hz power rise up time power ripple width Valid TG TG Vdd, TG TG, LED TG, BUSY TG, SPs TG, LED TG, BUSY TG, SPs TG, LED TG, BUSY SPs SPs LED LED Vdd Vdd Min. typ. 5 1 0 Max Unit mS uS uS uS uS uS uS uS uS uS uS uS uS mS mS mS mS Remarks slow debounce time, SRD fast debounce time, SRD mask = edge, SRD mask = edge, SRD mask = edge, SRD mask = level, SRD mask = level, SRD mask = level, SRD holdable output, SRD holdable output, SRD inside sentence between sentences, SRD SRD SRD 0 0 0 0 0 0 322 161 81 1 1 Specifications subject to change without notice, contact your sales representatives for the most recent information. 2/12 PID257*** 05/97 MOSEL VITELIC INC. Preliminary MSS0271 DC Characteristics at 4.5 V Symbol Parameter I SB I OP I IH I IL I LED I OH I OL I OHS I OLS I LEDT R TG d F/F d F/F standby I operation I input high I input low I output low I output high I output low I output high drive I output low sink I threshold sound to furn LED on pull low R frequency stability frequency variation Valid Vdd Vdd TG TG LED BUSY BUSY SPs SPs TG 23 5 10 9 -8 8 -90 200 75 10 Min. typ. Max 1 200 20 2 Unit uA uA uA uA mA mA mA mA mA % of IOHS Kohm % [F(4.5V) - F(4V)] / F(4.5V) % conditions Note:A bulk capacitor 0.1uF across the Vdd to Vss is demanded. DC Characteristics at 3.0 V Symbol I SB I OP I IH I IL I LED I OH I OL I OHS I OLS I LEDT R TG d F/F d F/F Parameter standby I operation I input high I input low I output low I output high I output low I output high drive I output low sink I threshold sound to furn LED on pull low R frequency stability frequency variation Valid Vdd Vdd TG TG LED BUSY BUSY SPs SPs TG Min. typ. Max 1 150 15 2 Unit conditions uA uA uA uA mA mA mA mA mA % of IOHS Kohm % [F(3V) - F(2.7V)] / F(3V) % 5 1 8 -3 3 -45 100 75 20 5 10 Specifications subject to change without notice, contact your sales representatives for the most recent information. 3/12 PID257*** 05/97 MOSEL VITELIC INC. Preliminary MSS0271 Signals SP+ and SPThey are tristate during standby. They are not at standby current when the data is in the middle. These two pins can drive buzzer or speaker, 8 ohm or 16 ohm, directly. The speaker used should have its band width (BW) at the center of your sound frequency domain or you are unable to play your sound good by this speaker. For instance, you have your sound spans over frequency from 100 Hz through 10 KHz. A speaker with BW meets requirement will play this sound good. A speaker with BW narrower than requirement (either has higher low-cut or lower high-cutoff) will distort the sound very much because that most of the energy of the playback sound is unable to be played by this speaker. This pair has zero output when sound data is zero. This pair has full output when sound data is the highest. This pair has half of full output when sound is silence at middle data value. This pair has half of full output when playing sound at appended memory-less mute. The output depends on Vdd bias very much. Herein zero output does not mean zero potential, neither ground. It is recommended to select voltage source carefully and do not supply this chip with a voltage potential source in poor flatness or in poor drive capability. What the poor source means either its potential drops as the load varies or its potential drops as its capacity exhausted. The speaker characeristics and housing impacts the loudness very much. TG This is a high true activating signal input pin. internal pull low R TG is built in. There is no schmit trigger circuit implemented. An Ramp up and Ramp down See the explanation of Audio. Sample Rate All the AC parameters depend on sample rate except three - t PUD, t P and t R. The numbers mentioned in this data sheet are based on 6 KHz sample rate if not specified. Higher SR has quicker LED flasher, quicker response. Lower SR has slower LED flasher, slower response. Retriggerable TG Retriggerable TG means the sound played could be terminated immediately while further TG activated and play the sound from the very beginning. Holdable and retriggerable This combination allows user controlling both the output and the input. Its output is holdable and the input could retrigger the former. This is an exquisite feature. It is not provided on this single trigger voice chip. Fix flash LED Fix 3 Hz flash means this pin turns LED lamp on for T LED3 and then turns it off for T LED3 alternately. Fix 6 Hz flash means quicker, it turns on T LED6 and then turns off T LED6. The 3 Hz as well as 6 Hz is sample rate dependent. When repeatedly playing a word, interesting LED flash may happen in concatenation. The word length may not be the multiples of T LED3 (or T LED6), a new flash cycle will start before the last flash cycle terminates. Dymanic Flash LED The LED turns on whenever the sound amplitude (the current from SPs) is over a certain threshold potential (I LEDT). The sound potential could be measured in data value as an alternative. Debounce time Either Fast or Slow debounce are provided by mask options. The Fast debounce acknowledges very short trigger. So, the sound will play "sensitively". User should be very carefully to choose trigger switch while "Fast debounce" is specified. IN0 and IN1 They should be bonded to ground both regularly. While abnormal lot (pitch shifted) is encountered, special bonding could be done herein. LB This pin could be optionally masked as either high true Busy signal or LED flasher which is turned on in sink way by I LED. Refers to paragrahps "Mask option" and "terms". Up to 3 types of LED flasher could be chosen. Application Notes Speaker The typical application speaker is 8 ohm, 1/4 watt. Refers to above paragraph SP+ and SP- for more description on required speaker. Buzzer The recommended resonant frequency should be 1 KHz to get the best sound response. The response BW also should be fit to the required sound band width. Refer to above paragraph SP+ and SP- for more description. PID257*** 05/97 Terms Audio Audio means the signal from the pin pair SP+ and SP-. Due to a sophisticated architecture, there demands no ramp up (or ramp down) to eliminate the pop noise at the sound starting and ending. Specifications subject to change without notice, contact your sales representatives for the most recent information. 4/12 MOSEL VITELIC INC. Preliminary MSS0271 Choice of sample rate The sample rate should be chosen before chip manufactured. Two sample rates are provided on S0271 - either 6200 KHz or 8400 KHz. User is able to select them on the attached PRF (product request form). Rosc No external Rosc is required. Audio band amplifier transistor No amplifier transistor is demanded. PCB layout To minimize the interference, the route from trigger switch to chip should be as short as possible. The route of trigger signal is recommended to as far away as possible to speaker output. CDS as trigger to be defined. Power On play This chip provides power on play function. User should be noted that the time parameter T PUD is zero. To connect the trigger to Vdd, the sound will be played whenever power is turned on. Cascading Cascading chips to have longer duration is possible by special wiring but not recommended. Paralleling Paralleling chips to have more triggers is possible by special wiring but not recommended. Bulk Capacitor A bulk capacitor 0.1uF across the Vdd to Vss is demanded when using 4.5V (or higher) working voltage. At every working voltage, the value of bulk capacitor should be less than or equal to 0.47uF. Bonding change while Rosc shifts MVI S0271 provides reliable built-in Rosc by advance technology. In case Rosc is shilfted (pitch shifted), the bonding change is able to bias Rosc into nominal value. The bonding changes are described on page 11/12. While the pitch shift encountered even it is rarely, the part number will have a postfix letter-capital "Z" while the lot number will have the two letter extension simultaneously. The two-letter extension could be "LH", "HL" or "HH". This two-letter extension tells how the bonding should be done which are described on page 11/12. Standard Code Line Up Times to Times to 1 2 3 4 5 6 Code# 002 010 017 018 020 021 Title Ho,Ho,Ho, Merry X'mas!! Happy Hollween!! Barking Dog Screaming Girl Croaking Frog Sound of Cow Repeat 0 1 2 0 2 1 Play 1 2 3 1 3 2 Trigger Edge Edge Edge Edge Edge Level Unhold Unhold Unhold Unhold Unhold Unhold Irret. Irret. Irret. Irret. Irret. Irret. LB Busy Busy Busy 6 Hz LED 3 Hz LED 3 Hz LED Deb. Fast Fast Fast SR (Hz) 6.2 K 6.2 K 8.4 K Remarks Fast 8.4 K Slow 6.2 K Slow 6.2 K Specifications subject to change without notice, contact your sales representatives for the most recent information. 5/12 PID257*** 05/97 MOSEL VITELIC INC. Preliminary MSS0271 TG COB Information Model Number : M9220 (P20) [for codes 050 and later 0 1 2 cm LB Vdd SP1 IN0 Vss SP2 IN1 NC Model Number : M9228 (P28) [for codes 001~049] 0 1 2 cm TG LB VDD SP1 VSS IN0 SP2 NC IN1 - Specifications subject to change without notice, contact your sales representatives for the most recent information. 6/12 PID257*** 05/97 MOSEL VITELIC INC. Preliminary MSS0271 Timing Critical Acceptable Power on Signal & Ripple tP 90% VDD VSS=0.0V 10% VDD tR 90% VDD Power Up Delay power TG t PUD To play TG t THAS t TLAE Audio LED t THLO t TLLF BUSY t THZH t TLZL t AELF t AEZL To play repeatedly TG t THAS t TLAE Audio LED t THLO BUSY t THZH t IWR2 t TLLF t TLZL Specifications subject to change without notice, contact your sales representatives for the most recent information. 7/12 PID257*** 05/97 MOSEL VITELIC INC. Preliminary MSS0271 Timing Diagram I. Edge Trigger Mask I.1. Unholdable output with BUSY a. When trigger is shorter than output TG AUDIO BUSY b. When trigger is longer than output I.2. Unholdable output with Fixed-Type LED Flasher a. When trigger is shorter than output TG AUDIO LED b. When trigger is longer than output I.3. Unholdable output with Dynamic-Type LED Flasher a. When trigger is shorter than output TG AUDIO LED b. When trigger is longer than output I.4. Holdable output with BUSY a. When trigger is shorter than a whole section output TG AUDIO BUSY b. When trigger is longer than a whole section output I.5. Holdable output with Fixed-Type LED Flasher a. When trigger is shorter than a whole section output TG AUDIO LED b. When trigger is longer than a whole section output I.6. Holdable output with Dynamic-Type LED Flasher a. When trigger is shorter than a whole section output TG AUDIO LED b. When trigger is longer than a whole section output I.7. Unholdable output with Retrigger a. When trigger is shorter than a whole section output TG AUDIO b. When trigger is longer than a whole section output Specifications subject to change without notice, contact your sales representatives for the most recent information. 8/12 PID257*** 05/97 MOSEL VITELIC INC. Preliminary MSS0271 II. Level Trigger Mask II.1. Unholdable output with BUSY output a. When trigger is shorter than a whole section output TG AUDIO BUSY b. When trigger is longer than a whole section output II.2. Unholdable output with Fixed-Type LED Flasher a. When trigger is shorter than a whole section output TG AUDIO LED b. When trigger is longer than a whole section output II.3. Unholdable output with Dynamic-Type LED Flasher a. When trigger is shorter than a whole section output TG AUDIO LED b. When trigger is longer than a whole section output II.4. Holdable output with BUSY output a. When trigger is shorter than a whole section output TG AUDIO BUSY b. When trigger is longer than a whole section output II.5. Holdable output with Fixed-Type LED Flasher a. When trigger is shorter than a whole section output TG AUDIO LED b. When trigger is longer than a whole section output II.6. Holdable output with Dynamic-Type LED Flasher a. When trigger is shorter than a whole section output TG AUDIO LED b. When trigger is longer than a whole section output II.7. Unholdable output with Retrigger TG AUDIO Specifications subject to change without notice, contact your sales representatives for the most recent information. 9/12 PID257*** 05/97 MOSEL VITELIC INC. Preliminary MSS0271 I. Typical Application Circuit I, Rosc less, LED output TG LED SP1 IN0 IN1 MSS0271 SP2 Speaker 8 ohm or 16 ohm TG LED SP1 IN0 IN1 MSS0271 SP2 Buzzer II. Typical Application Circuit II, Rosc less, Busy output TG BUSY SP1 IN0 IN1 MSS0271 SP2 Speaker 8 ohm or 16 ohm TG BUSY SP1 IN0 IN1 MSS0271 SP2 Buzzer 2 1 9 Pad Information Pad# 1 2 3 4 5 6 7 8 9 Signal TG LB IN0 IN1 NC SP2 Vss SP1 Vdd X -669 -663 67 656 570 195 -63 -322 -681 Y -170 -409 -409 -409 390 390 390 390 390 MSS0271 1660 X 1140 um Substrate is Vdd Pad size is 90 X 90 um 8 7 6 3 4 5 Specifications subject to change without notice, contact your sales representatives for the most recent information. 10/12 PID257*** 05/97 MOSEL VITELIC INC. Preliminary MSS0271 Bonding to Offset the Shifted Pitch Below three special bonding means are used to offset the shifted pitch (frequency) and let it perform normally. This happens only for those chip lots have their part number with postfix letter "Z". To not use these special bonding means on normal part is strongly recommended. Of course, the copper route may have different layout on PCB (printed circuit board). It should be decided by user himself. Below shows only what we recommended, not restricted. I. Type LH Bonding For lot number with extension letters "LH" II. Type HL Bonding For lot number with extension letters "HL" LB IN1 IN0 TG IN1 IN0 LB TG S0271 Substrate is Vdd Vss Vdd S0271 Substrate is Vdd Vss Vdd SP2 SP1 to positive power to negative power SP2 SP1 to positive power to negative power III. Type HH Bonding For lot number with extension letters "HH" LB IN1 IN0 TG S0271 Substrate is Vdd Vss Vdd Revision history: pid 257* 12/96 pid 257** 02/97 pid 257*** 05/97 SP2 SP1 to positive power to negative power Taiwan #1 Creation Road I, Science - based Industrial Park, Hsinchu, 30077 Taiwan, ROC "audio_reply@mosel.com.tw" TEL: 886-3-5770055 FAX: 886-3-5772788 FAX: 886-3-5784732 Mdm: 886-3-578-0493 http:\\www.moselvitelic.com Taipei 7F, #102 Section 3, Ming Chung E. Road, Taipei, 105 Taiwan, ROC TEL: 886-2-5451213 FAX: 886-2-5451214 Mdm: 886-2-545-1464 China (Vitelic HKG ShenZhen) Room #209, #19 ZhenHua road, ShenZhen, China TEL: 86-755-334-5766 FAX: 86-755-332-3995 Mdm: 86-755-332-3995 Hongkong #19 Dai Fu Street, Taipo Industrial Estate, Taipo, N.T. Hongkong TEL: 852-2388-8277 (MKO) TEL: 852-2665-4883 FAX: 852-2664-2406 FAX: 852-2770-8011 (MKO) Mdm: 852-2388-0244 (MKO) U.S.A. #3910 North First Street, San Jose, CA. 65134-1501 U.S.A. TEL: 1-408-433-6000 FAX: 1-408-433-0952 Japan Rm. 302, Annex-G, 1-31-10 Higashi-Nakano Nakano-Ku, Tokyo 164 Japan TEL:81-3-3365-2851 FAX:81-3-3365-2836 Specifications subject to change without notice, contact your sales representatives for the most recent information. 11/12 PID257*** 05/97 MOSEL VITELIC INC. Preliminary MSS0271 To: Attn : Mosel Vitelic Inc. 886-3-578-4732 (fax) Sales & Marketing Department Product Request Form I hereby request MVI to start preparing produce MSS0271 which is specified as below description. Its voice storage limitation is 4380h. General Descriptions Customer Cannot proceed when empty Agent Sales Repr'tives Providing to MVI Who is MVI sales you contact ? 8-bit PCM sound files .WAV sound files DAT or equivalent application is special, see our written memo Others EPROMs with data inside Service Required from MVI files to be programmed into EPROM emulation board & Eprom Confirm table Others Holdable & Irretriggerable Unholdable & Irretriggerable Unholdable & Retriggerable No use & don't care LB = Busy output LB = dynamic LED flasher LB = 3Hz LED flasher LB = 6Hz LED falsher No use and don't care Power Source Title: Edge Level Output Device Chip descriptions Buzzer (F fr =1KHz) Speaker (0.25W, 16 ohm, 1" diam.) Speaker (0.25W, 8 ohm, 1" diam.) Other: Working Voltage 2.5 V 3.0 V 3.5 V 4.0 V I already read this data sheet PID257 *** and understand MSS0271 completely and know how to specify to fit my requirement. Built-in Rosc at 6200 Hz Built-in Rosc at 8400 Hz Debounce = Slow, T T1 Debounce = Fast, T T2 4.5 V w/Bulk Cap. 5.0 V w/Bulk Cap. 5.5 V w/Bulk Cap. 6.0 V w/Bulk Cap. Battery size "D" Battery size "AA" Battery size "AAA" other size = Mains Other Voice content Voice Length S <2.79 s Mute length (behind) S 00h Total Length 00h <20000h 0< repeat times total play times 00h <4380h <7 1< <8 Company Name : Signature : Department/Section : Specifications subject to change without notice, contact your sales representatives for the most recent information. Fax number : Date : Position Title : 12/12 PID257*** 05/97 |
Price & Availability of MSS0271
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |