|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
PIC18F2420/2520/4420/4520 PIC18F2420/2520/4420/4520 Rev. A1 Silicon Errata Sheet The PIC18F2420/2520/4420/4520 Rev. A1 parts you have received conform functionally to the Device Data Sheet (DS39631), except for the anomalies described below. Any Data Sheet Clarification issues related to the PIC18F2420/2520/4420/4520 will be reported in a separate Data Sheet errata. Please check the Microchip web site for any existing issues. All the problems listed here will be addressed in future revisions of the PIC18F2420/2520/4420/4520 silicon. The following silicon errata apply only to PIC18F2420/2520/4420/4520 devices with these Device/Revision IDs: Part Number PIC18F2420 PIC18F2520 PIC18F4420 PIC18F4520 Device ID 01 0001 010 01 0001 000 01 0000 110 01 0000 100 Revision ID 00001 00001 00001 00001 1. Module: MSSP In its current implementation, the I2CTM Master mode operates as follows: a) The Baud Rate Generator for I2C in Master mode is slower than the rates specified in Table 17-3 of the Device Data Sheet. For this revision of silicon, use the values shown in Table 1 in place of those shown in Table 17-3 of the Device Data Sheet. The differences are shown in bold text. b) Use the following formula in place of the one shown in Register 17-4 (SSPCON1) of the Device Data Sheet for bit description SSPM3:SSPM0 = 1000. SSPADD = INT((FCY/FSCL) - (FCY/1.111 MHz)) - 1 Date Codes that pertain to this issue: All engineering and production devices. The Device IDs (DEVID1 and DEVID2) are located at addresses 3FFFFEh:3FFFFFh in the device's configuration space. They are shown in hexadecimal in the format "DEVID2 DEVID1". TABLE 1: FOSC 40 MHz 40 MHz 40 MHz 16 MHz 16 MHz 16 MHz 4 MHz 4 MHz 4 MHz Note 1: I2CTM CLOCK RATE w/BRG FCY 10 MHz 10 MHz 10 MHz 4 MHz 4 MHz 4 MHz 1 MHz 1 MHz 1 MHz FCY * 2 20 MHz 20 MHz 20 MHz 8 MHz 8 MHz 8 MHz 2 MHz 2 MHz 2 MHz BRG Value 0Eh 15h 59h 05h 08h 23h 01h 08h 00h FSCL (2 Rollovers of BRG) 400 kHz(1) 312.5 kHz 100 kHz 400 kHz(1) 308 kHz 100 kHz 333 kHz(1) 100 kHz 1 MHz(1) The I2CTM interface does not conform to the 400 kHz I2C specification (which applies to rates greater than 100 kHz) in all details, but may be used with care where higher rates are required by the application. (c) 2005 Microchip Technology Inc. DS80209D-page 1 PIC18F2420/2520/4420/4520 2. Module: MSSP When the MSSP is configured for SPITM Master mode, the SDO pin cannot be disabled by setting the TRISC<5> bit. The SDO pin always outputs the content of SSPBUF regardless of the state of the TRIS bit. In Slave mode with Slave Select enabled, SSPM3:SSPM0 = 0010 (SSPCON1<3:0>), the SDO pin can be disabled by placing a logic high level on the SS pin (RA5). Work around None. Date Codes that pertain to this issue: All engineering and production devices. 4. Module: MSSP In 10-bit Addressing mode, when a Repeated Start is issued, followed by the high address byte and a write command (R/W = 0), an ACK is not issued. Work around There are two work arounds available: 1. Single-Master Environment: In a single-master environment, the user must issue a Stop, then a Start, followed by a write to the address high, then the address low followed by the data. 2. Multi-Master Environment: In a multi-master environment, the user must issue a Repeated Start, send a dummy write command to a different address, issue another Repeated Start and then send a write to the original address. This procedure will help maintain control of the bus. Date Codes that pertain to this issue: All engineering and production devices. 3. Module: MSSP After an I2C transfer is initiated, the SSPBUF register may be written for up to 10 TCY before additional writes are blocked. The data transfer may be corrupted if SSPBUF is written during this time. The WCOL bit is set any time an SSPBUF write occurs during a transfer. Work around Avoid writing SSPBUF until the data transfer is complete, indicated by the setting of the SSPIF bit (PIR1<3>). Verify the WCOL bit (SSPCON1<7>) is clear after writing SSPBUF to ensure any potential transfer in progress is not corrupted. Date Codes that pertain to this issue: All engineering and production devices. 5. Module: MSSP I2C Receive mode should be enabled (i.e., RCEN bit should be set) only when the system is idle (i.e., when ACKEN, RCEN, PEN, RSEN and SEN all equal zero). It should not be possible to set the RCEN bit when the system is not idle, however, the RCEN bit can be set under this circumstance. Work around Wait for the system to become idle before setting the RCEN bit. This requires a check for the following bits to be clear: ACKEN, RCEN, PEN, RSEN and SEN. Date Codes that pertain to this issue: All engineering and production devices. DS80209D-page 2 (c) 2005 Microchip Technology Inc. PIC18F2420/2520/4420/4520 6. Module: ECCP When the ECCP1 auto-shutdown feature is configured for automatic restart by setting the PRSEN bit (PWM1CON<7>), the pulse terminates immediately in a shutdown event. In addition, the pulse may restart within the period if the shutdown condition expires. This may result in the generation of short pulses on the PWM output(s). Work around Configure the auto-shutdown for software restart by clearing the PRSEN bit (PWM1CON<7>). The PWM can be re-enabled by clearing the ECCPASE bit (ECCP1AS<7>) after the shutdown condition expires. Date Codes that pertain to this issue: All engineering and production devices. 9. Module: ECCP and CCP The CCP1 and CCP2 configured for PWM mode, with 1:1 Timer2 prescaler and duty cycle set to the period minus 1, may result in the PWM output(s) remaining at a logic low level. Clearing the PR2 register to select the fastest period may also result in the output(s) remaining at a logic low output level. Work around To ensure a reliable waveform, verify that the selected duty cycle does not equal the 10-bit period minus 1 prior to writing these locations, or use 1:4 or 1:16 Timer2 prescale. Also, verify the PR2 register is not written to 00h. All other duty cycle and period settings will function as described in the Device Data Sheet. The ECCP and CCP modules remain capable of 10-bit accuracy. Date Codes that pertain to this issue: All engineering and production devices. 7. Module: ECCP When monitoring a shutdown condition using a bit test on the ECCPASE bit (ECCP1AS<7>), or performing a bit operation on the ECCPASE bit, the device may produce unexpected results. Work around Before performing a bit test or bit operation on the ECCPASE bit, copy the ECCP1AS register to the working register and perform the operation there. By avoiding these operations on the ECCPASE bit in the ECCP1AS register, the module will operate normally. In Example 1, ECCPASE bit operations are performed on the W register. 10. Module: ECCP ECCP1 configured for auto-shutdown with Comparator 1 corrupts the PWM duty cycle pulse. In addition, it does not always synchronize the pulse to the beginning of the period and the end of the pulse can occur at any time within the period. Work around Use FLT0 for the auto-shutdown source. Applications which can tolerate a shutdown response time of several TCYs may use the comparator interrupt flag to detect a shutdown event and disable the PWM by clearing the EECPASE bit (ECCP1AS<7>). Date Codes that pertain to this issue: All engineering and production devices. EXAMPLE 1: MOVF BTFSC BRA ECCP1AS, W WREG, ECCPASE SHUTDOWN_ROUTINE Date Codes that pertain to this issue: All engineering and production devices. 11. Module: ECCP 8. Module: ECCP The auto-shutdown source, FLT0, has inverse polarity from the description in Section 16.4.7 "Enhanced PWM Auto-Shutdown" of the Device Data Sheet. A logic high-voltage level on FLT0 will generate a shutdown on ECCP1. Work around None. Date Codes that pertain to this issue: All engineering and production devices. When the shutdown state of the PWM pin(s) is configured to tri-state the outputs, the device may consume higher than expected current during the shutdown event. Work around Configure the PWM output for either a high or low logic state during the shutdown via the PSSAC1:PSSAC0 (ECCP1AS<3:2>) and PSSBD1: PSSBD0 (ECCP1AS<1:0>) bits. Clearing the autoshutdown event will return the device to normal current consumption levels. Date Codes that pertain to this issue: All engineering and production devices. (c) 2005 Microchip Technology Inc. DS80209D-page 3 PIC18F2420/2520/4420/4520 12. Module: ECCP The PWM pin(s) may change state if a breakpoint is encountered during emulation and an autoshutdown event occurs via FLT0. This affects the MPLAB(R) ICD 2 debugger and the ICE 2000 and ICE 4000 emulators. Work around During emulation, use the comparator for autoshutdown. Applications which can tolerate a shutdown response time of several TCYs may use the external interrupt flag, INT0IF, to detect a shutdown event and disable the PWM by clearing the ECCPASE bit (ECCP1AS<7>). Date Codes that pertain to this issue: All engineering and production devices. 14. Module: ECCP When a shutdown condition occurs, the output port is made inactive for the duration of the event. After the event that caused the shutdown ends, the ECCP module enables the PWM output right away instead of waiting until the beginning of the next PWM cycle. Work around Disable the auto-restart feature in software, polling the Timer2 Interrupt Flag (TMR2IF) and wait until it is set before clearing the ECCPASE bit. Date Codes that pertain to this issue: All engineering and production devices. 15. Module: ECCP When switching direction in Full-Bridge PWM mode, the modulated outputs will switch immediately instead of waiting for the next PWM cycle. This may generate unexpected short pulses on the modulated outputs. Work around Disable the PWM or set duty cycle to zero prior to switching directions. Date Codes that pertain to this issue: All engineering and production devices. 13. Module: ECCP and CCP When operating either Timer1 or Timer3 as a counter with a prescale value other than 1:1 and operating the ECCP in Compare mode with the Special Event Trigger (CCP1CON bits CCP1M3:CCP1M0 = 1011), the Special Event Trigger Reset of the timer occurs as soon as there is a match between TMRxH:TMRxL and CCPR1H:CCPR1L. This differs from the PIC18F452, where the Special Event Trigger Reset of the timer occurs on the next prescaler output pulse after the match between TMRxH:TMRxL and CCPR1H:CCPR1L. Work around To achieve the same timer Reset period on the PIC18F4520 family as the PIC18F452 family for a given clock source, add 1 to the value in CCPR1H:CCPR1L. In other words, if CCPR1H:CCPR1L = x for the PIC18F452, to achieve the same Reset period on the PIC18F4520 family, CCPR1H:CCPR1L = x + 1, where the prescale is 1, 2, 4 or 8 depending on the T1CKPS1:T1CKPS0 bit values. Date Codes that pertain to this issue: All engineering and production devices. DS80209D-page 4 (c) 2005 Microchip Technology Inc. PIC18F2420/2520/4420/4520 16. Module: A/D The A/D offset is greater than the specified limit in Table 26-24 of the Device Data Sheet. The additional Parameter A06A and updated conditions and limits are shown in bold text in Table 2. Work around Three work arounds exist. 1. Configure the A/D to use the VREF+ and VREFpins for the voltage references. This is done by setting the VCFG<1:0> bits (ADCON1<5:4>). 2. Perform a conversion on a known voltage reference voltage and adjust the A/D result in software. 3. Increase system clock speed to 40 MHz and adjust A/D settings accordingly. Higher system clock frequencies decrease offset error. TABLE 2: A/D CONVERTER CHARACTERISTICS: PIC18FX42X/X52X (INDUSTRIAL, EXTENDED) PIC18LFX42X/X52X (INDUSTRIAL) Characteristic Offset Error Offset Error Min -- -- Typ -- -- Max <1.5 <3.5 Units LSb LSb Conditions VREF = VREF+ and VREFVREF = VSS and VDD Param Symbol No. A06A A06 EOFF EOFF Date Codes that pertain to this issue: All engineering and production devices. 17. Module: BOD The BOD module may reset below the minimum operating voltage of the device when configured for BORV1:BORV0 = 11. The updated Reset voltage specifications are shown in bold in Table 3. 18. Module: EUSART When performing back-to-back transmission in 9-bit mode (TX9D bit in the TXSTA register is set), an ongoing transmission's timing can be corrupted if the TX9D bit (for the next transmission) is not written immediately following the setting of TXIF. This is because any write to the TXSTA register results in a reset of the baud rate timer which will effect any ongoing transmission. Work around V TABLE 3: Param Sym No. D005 BROWN-OUT RESET VOLTAGE Characteristic Min Typ Max Unit VBOR Brown-out Reset Voltage PIC18LF2420/2520/4420/4520 BORV1:BORV0 = 11 N/A 2.05 N/A Work around Use the next higher BOD voltage setting to ensure a low VDD is detected above 2.0V. Date Codes that pertain to this issue: All engineering and production devices. Load TX9D just after TXIF is set, either by polling TXIF or by writing TX9D at the beginning of the Interrupt Service Routine, or only write to TX9D when a transmission is not in progress (TRMT = 1). Date Codes that pertain to this issue: All engineering and production devices. (c) 2005 Microchip Technology Inc. DS80209D-page 5 PIC18F2420/2520/4420/4520 19. Module: EUSART When performing back-to-back transmission in 9-bit mode (TX9D bit in the TXSTA register is set), the second byte may be corrupted if it is written into TXREG immediately after the TMRT bit is set. Work around Execute a software delay, at least one-half the transmission's bit time, after TMRT is set and prior to writing subsequent bytes into TXREG. Date Codes that pertain to this issue: All engineering and production devices. 21. Module: Timer1/Timer3 When Timer1 or Timer3 is in External Clock Synchronized mode and the external clock period is between 1 and 2 TCY, interrupts will occasionally be skipped. Work around Avoid using an external clock with a period (1/ frequency) between 1 and 2 TCY. Date Codes that pertain to this issue: All engineering and production devices. 22. Module: Timer1/Timer3 20. Module: Timer1/Timer3 When Timer1 or Timer3 is configured for external clock source, and the CCPxCON register is configured with 0x0B (Compare mode, trigger special event), the timer is not reset on a Special Event Trigger. Work around Modify firmware to reset the Timer1/Timer3 registers upon detection of the compare match condition -- TMRxL and TMRxH. Date Codes that pertain to this issue: All engineering and production devices. When Timer1/Timer3 is operating in 16-bit mode and the prescale setting is not 1:1, a write to the TMR1H/TMR3H Buffer registers may lengthen the duration of the period between the increments of the timer for the period in which TMR1H/TMR3H was written. Work around Two work arounds are available: 1) Stop Timer1/ Timer3 before writing the TMR1H/TMR3H registers; 2) Write TMR1L/TMR3L immediately after writing TMR1H/TMR3H. Date Codes that pertain to this issue: All engineering and production devices. DS80209D-page 6 (c) 2005 Microchip Technology Inc. PIC18F2420/2520/4420/4520 23. Module: Interrupts If an interrupt occurs during a two-cycle instruction that modifies the STATUS, BSR or WREG register, the unmodified value of the register will be saved to the corresponding Fast Return (Shadow) register and upon a fast return from the interrupt, the unmodified value will be restored to the STATUS, BSR or WREG register. For example, if a high priority interrupt occurs during the instruction, MOVFF TEMP, WREG, the MOVFF instruction will be completed and WREG will be loaded with the value of TEMP before branching to ISR. However, the previous value of WREG will be saved to the Fast Return register during ISR branching. Upon return from the interrupt with a fast return, the previous value of WREG in the Fast Return register will be written to WREG. This results in WREG containing the value it had before execution of MOVFF TEMP, WREG. Affected instructions are: MOVFF Fs, Fd where Fd is WREG, BSR or STATUS; MOVSF Zs, Fd where Fd is WREG, BSR or STATUS; and MOVSS [Zs], [Zd] where the destination is WREG, BSR or STATUS. Work around 1. Assembly Language Programming: a) If any two-cycle instruction is used to modify the WREG, BSR or STATUS register, do not use the RETFIE FAST instruction to return from the interrupt. Instead, save/restore WREG, BSR and STATUS via software per Example 9-1 in the Device Data Sheet. Alternatively, in the case of MOVFF, use the MOVF instruction to write to WREG instead. For example, use: MOVF MOVWF TEMP, W BSR instead of: MOVFF TEMP, BSR. b) As another alternative, the following work around shown in Example 2 can be used. This example overwrites the Fast Return register by making a dummy call to Foo with the fast option in the high priority service routine. EXAMPLE 2: ISR @ 0x0008 CALL Foo, FAST Foo: POP : : RETFIE FAST ; store current value of WREG, BSR, STATUS for a second time ; clears return address of Foo call ; insert high priority ISR code here (c) 2005 Microchip Technology Inc. DS80209D-page 7 PIC18F2420/2520/4420/4520 2. C Language Programming: The exact work around depends on the compiler in use. Please refer to your C compiler documentation for details. If using the Microchip MPLAB(R) C18 C Compiler, define both high and low priority interrupt handler functions as "low priority" by using the pragma interruptlow directive. This directive instructs the compiler to not use the RETFIE FAST instruction. If the proper high priority interrupt bit is set in the IPRx register, then the interrupt is treated as high priority in spite of the pragma interruptlow directive. The code segment shown in Example 3 demonstrates the work around using the C18 compiler: EXAMPLE 3: #pragma interruptlow MyLowISR void MyLowISR(void) { // Handle low priority interrupts. } // Although MyHighISR is a high priority interrupt, use interruptlow pragma so that // the compiler will not use retfie FAST. #pragma interruptlow MyHighISR void MyHighISR(void) { // Handle high priority interrupts. } #pragma code highVector=0x08 void HighVector (void) { _asm goto MyHighISR _endasm } #pragma code /* return to default code section */ #pragma code lowVector=0x18 void LowVector (void) { _asm goto MyLowISR _endasm } #pragma code /* return to default code section */ Date Codes that pertain to this issue: All engineering and production devices. DS80209D-page 8 (c) 2005 Microchip Technology Inc. PIC18F2420/2520/4420/4520 24. Module: EUSART The EUSART auto-baud feature may periodically measure the incoming baud rate incorrectly. The rate of incorrect baud rate measurements will depend on the frequency of the incoming synchronization byte and the system clock frequency. Work around None. 28. Module: MSSP In I2C Master mode, the BRG value of `0' may not work correctly. Work around Use a BRG value greater than `0' by setting SSPADD 1. 29. Module: MSSP In I2C Master mode, the RCEN bit is set by software to begin data reception and cleared by the peripheral after a byte is received. After a byte is received, the device may take up to 80 TCY to clear RCEN and 800 TCY when using MPLAB(R) ICD 2 and MPLAB ICE emulators. Work around Single byte receptions are typically not affected, since the delay between byte receptions is typically long enough for the RCEN bit to clear. For multiple byte receptions, the software must wait until the bit is cleared by the peripheral before the next byte can be received. 25. Module: EUSART In Synchronous mode (SYNC = 1) with clock polarity high (SCKP = 1), the EUSART transmits a shorter than expected clock on the CK pin for bit 0. Work around None. 26. Module: EUSART In Synchronous mode, EUSART baud rates using SPBRG values of `0' and `1' may not function correctly. Work around Use another baud rate configuration to generate the desired baud rate. 30. Module: MSSP Setting the SEN bit initiates a Start sequence on the bus, after which, the SEN bit is cleared automatically by hardware. If the SEN bit is set again (without an address byte being transmitted), a Start sequence will not commence and the SEN bit will not be cleared. This condition causes the bus to remain in an active state. The system is Idle when ACKEN, RCEN, PEN, RSEN and SEN are clear. Work around Set the PEN or RSEN bit to transmit a Stop or Repeated Start sequence, although the SEN bit may still be set, indicating the bus is active. After the sequence has completed, the PEN, RSEN and SEN bit will be clear, indicating the bus is Idle. Clearing and setting the SSPEN bit will also reset the I2C peripheral and clear the PEN, RSEN and SEN status bits. 27. Module: MSSP In an I2CTM system with multiple slave nodes, an unaddressed slave may respond to bus activity when data on the bus matches its address. The first occurrence will set the BF bit. The second occurrence will set the BF and SSPOV bits. In both situations, the SSPIF bit is not set and an interrupt will not occur. The device will vector to the Interrupt Service Routine only if the interrupt is enabled and an address match occurs. Work around The I2C slave must clear the SSPOV bit after each I2C address match to maintain normal operation. (c) 2005 Microchip Technology Inc. DS80209D-page 9 PIC18F2420/2520/4420/4520 31. Module: MSSP In SPI mode, the Buffer Full flag (BF bit in the SSPSTAT register), the Write Collision Detect bit (WCOL bit in SSPCON1) and the Receive Overflow Indicator bit (SSPOV in SSPCON1) are not reset upon disabling the SPI module (by clearing the SSPEN bit in the SSPCON1 register). For example, if SSPBUF is full (BF bit is set) and the MSSP module is disabled and re-enabled, the BF bit will remain set. In SPI Slave mode, a subsequent write to SSPBUF will result in a write collision. Also, if a new byte is received, a receive overflow will occur. Work around Ensure that if the buffer is full, SSPBUF is read (thus clearing the BF flag) and WCOL is clear before disabling the MSSP module. If the module is configured in SPI Slave mode, ensure that the SSPOV bit is clear before disabling the module. SDO 32. Module: MSSP (SPI Mode) When the SPI is using Timer2/2 as the clock source, a shorter than expected SCK pulse may occur on the first bit of the transmitted/received data (Figure 1). FIGURE 1: SCK PULSE VARIATION USING TIMER2/2 Write SSPBUF bit 0 = 1 bit 1 = 0 bit 2 = 1 . . . . SCK Work around To avoid producing the short pulse, turn off Timer2 and clear the TMR2 register, load the SSPBUF with the data to transmit and then turn Timer2 back on. Refer to Example 4 for sample code. EXAMPLE 4: AVOIDING THE INITIAL SHORT SCK PULSE ;Data received? ;(Xmit complete?) ;No ;W = SSPBUF ;Save in user RAM ;W = TXDATA ;Timer2 off ;Clear Timer2 ;Xmit New data ;Timer2 on LOOP BTFSS SSPSTAT, BF BRA MOVF MOVWF MOVF BCF CLRF MOVWF BSF LOOP SSPBUF, W RXDATA TXDATA, W T2CON, TMR2ON TMR2 SSPBUF T2CON, TMR2ON DS80209D-page 10 (c) 2005 Microchip Technology Inc. PIC18F2420/2520/4420/4520 33. Module: Timer1 (Asynchronous Counter) When writing to the TMR1H register, under specific conditions, it is possible that the TMR1L register will miss a count while connected to the external oscillator via the T1OSO and T1OSI pins. When Timer1 is started, the circuitry looks for a falling edge before a rising edge can increment the counter. Writing to the TMR1H register is similar to starting Timer1; therefore, the former logic stated applies any time the TMR1H register is written. If the TMR1H register is not completely written to during the high pulse of the external clock, then the TMR1L register will miss a count due to the circuit operation stated previously. The high pulse of a 32.768 kHz external clock crystal yields a 15.25 s window for the write to TMR1H to occur. The amount of instructions that can be executed within this window is frequency dependent, as shown in Table 4 below. Work around Operating Conditions: FOSC 4 MHz, no wake-ups from Sleep, Timer1 interrupt enabled, global interrupts enabled. The code excerpts in Example 5 and Example 6 show how the TMR1H register can be updated while the external clock (32.768 kHz) is still on its high pulse. The importance of the code examples is that the bold instructions are executed within the first 15.25 s high pulse on the external clock after the Timer1 overflow occurs. This will allow the TMR1L register to increment correctly. TABLE 4: FREQUENCY DEPENDENT INSTRUCTION EXECUTION AMOUNTS FOSC 1 MHz 2 MHz 4 MHz 8 MHz 16 MHz 20 MHz 40 MHz TCY (s) 4 2 1 0.5 0.25 0.2 0.1 TCY within 15.25 s 3.81 7.63 15.25 30.5 61 76.25 152.5 EXAMPLE 5: ISR @ 0x0008 BRA HIGHINT BTFSC BSF PIC18 HIGH PRIORITY INTERRUPT SERVICE ROUTINE ; (3-4Tcy), fixed interrupt latency ; (2Tcy), go to high priority interrupt routine HIGHINT PIR1, TMR1IF TMR1H, 7 ; (1Tcy), did a Timer1 overflow occur? ; (1Tcy) Yes, reload for a 1 second overflow RETFIE FAST Total = 7-8 TCY (if Timer1 overflow occurred) (c) 2005 Microchip Technology Inc. DS80209D-page 11 PIC18F2420/2520/4420/4520 EXAMPLE 6: ISR @ 0x0018 MOVFF MOVFF MOVFF BTFSS BRA BSF STATUS, STATUS_TEMP WREG, WREG_TEMP BSR, BSR_TEMP PIR1, TMR1IF EXIT TMR1H, 7 PIC18 LOW PRIORITY INTERRUPT SERVICE ROUTINE ; (3-4Tcy), fixed interrupt latency ; (2Tcy), save STATUS register ; (2Tcy), save working register, refer to note 1 ; (2Tcy), save BSR register, refer to note 1 ; (2Tcy), did a Timer1 overflow occur? ; No ; (1Tcy) Yes, reload for a 1 second overflow EXIT MOVFF BSR_TEMP, BSR MOVFF WREG_TEMP, WREG MOVFF STATUS_TEMP, STATUS RETFIE ;restore BSR register, refer to note 1 ;restore working register, refer to note 1 ;restore STATUS register Total = 12-13 TCY (if Timer1 overflow occurred) Note: These instructions are required based on the function of the ISR. If the only code in the ISR is to reload Timer1, then they are not required, but may be required if additional code is added. DS80209D-page 12 (c) 2005 Microchip Technology Inc. PIC18F2420/2520/4420/4520 REVISION HISTORY Rev A Document (9/2004) First revision of this document which includes silicon issues 1-6 (ECCP), 7-11 (MSSP), 12 (ECCP and CCP), 13 (A/D), 14-15 (Timer1/Timer3) and 16 (BOD/HLVD). Rev B Document (11/2004) Changes made to silicon issue 7 (MSSP), 9 (MSSP) and 10 (MSSP). Added silicon issue 17 (EUSART), 18 (Interrupts), 19 (ECCP) and 20 (Timer1/Timer3). Rev C Document (2/2005) Added Date Code information to all issues, updated text and reordered issues for clarity. Issues in this revision are: 1-5 (MSSP), 6-8, 10-12, 14-15 (ECCP), 9, 13 (ECCP and CCP), 16 (A/D), 17 (BOD), 18-19 (EUSART), 20-22 (Timer1/Timer3) and 23 (Interrupts). Rev D Document (12/2005) Updated issues 4 (MSSP), 9 (ECCP and CCP) and 23 (Interrupts). Added issues 24-26 (EUSART), 27-31 (MSSP), 32 (MSSP - SPI Mode) and 33 (Timer1 - Asynchronous Counter). (c) 2005 Microchip Technology Inc. DS80209D-page 13 PIC18F2420/2520/4420/4520 NOTES: DS80209D-page 14 (c) 2005 Microchip Technology Inc. Note the following details of the code protection feature on Microchip devices: * * Microchip products meet the specification contained in their particular Microchip Data Sheet. Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip's Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property. Microchip is willing to work with the customer who is concerned about the integrity of their code. Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as "unbreakable." * * * Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break Microchip's code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE. Microchip disclaims all liability arising from this information and its use. Use of Microchip's products as critical components in life support systems is not authorized except with express written approval by Microchip. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights. Trademarks The Microchip name and logo, the Microchip logo, Accuron, dsPIC, KEELOQ, microID, MPLAB, PIC, PICmicro, PICSTART, PRO MATE, PowerSmart, rfPIC, and SmartShunt are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. AmpLab, FilterLab, Migratable Memory, MXDEV, MXLAB, PICMASTER, SEEVAL, SmartSensor and The Embedded Control Solutions Company are registered trademarks of Microchip Technology Incorporated in the U.S.A. Analog-for-the-Digital Age, Application Maestro, dsPICDEM, dsPICDEM.net, dsPICworks, ECAN, ECONOMONITOR, FanSense, FlexROM, fuzzyLAB, In-Circuit Serial Programming, ICSP, ICEPIC, Linear Active Thermistor, MPASM, MPLIB, MPLINK, MPSIM, PICkit, PICDEM, PICDEM.net, PICLAB, PICtail, PowerCal, PowerInfo, PowerMate, PowerTool, Real ICE, rfLAB, rfPICDEM, Select Mode, Smart Serial, SmartTel, Total Endurance, UNI/O, WiperLock and Zena are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. (c) 2005, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. Microchip received ISO/TS-16949:2002 quality system certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona and Mountain View, California in October 2003. The Company's quality system processes and procedures are for its PICmicro(R) 8-bit MCUs, KEELOQ(R) code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip's quality system for the design and manufacture of development systems is ISO 9001:2000 certified. (c) 2005 Microchip Technology Inc. DS80209D-page 15 WORLDWIDE SALES AND SERVICE AMERICAS Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: http://support.microchip.com Web Address: www.microchip.com Atlanta Alpharetta, GA Tel: 770-640-0034 Fax: 770-640-0307 Boston Westborough, MA Tel: 774-760-0087 Fax: 774-760-0088 Chicago Itasca, IL Tel: 630-285-0071 Fax: 630-285-0075 Dallas Addison, TX Tel: 972-818-7423 Fax: 972-818-2924 Detroit Farmington Hills, MI Tel: 248-538-2250 Fax: 248-538-2260 Kokomo Kokomo, IN Tel: 765-864-8360 Fax: 765-864-8387 Los Angeles Mission Viejo, CA Tel: 949-462-9523 Fax: 949-462-9608 San Jose Mountain View, CA Tel: 650-215-1444 Fax: 650-961-0286 Toronto Mississauga, Ontario, Canada Tel: 905-673-0699 Fax: 905-673-6509 ASIA/PACIFIC Australia - Sydney Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 China - Beijing Tel: 86-10-8528-2100 Fax: 86-10-8528-2104 China - Chengdu Tel: 86-28-8676-6200 Fax: 86-28-8676-6599 China - Fuzhou Tel: 86-591-8750-3506 Fax: 86-591-8750-3521 China - Hong Kong SAR Tel: 852-2401-1200 Fax: 852-2401-3431 China - Qingdao Tel: 86-532-8502-7355 Fax: 86-532-8502-7205 China - Shanghai Tel: 86-21-5407-5533 Fax: 86-21-5407-5066 China - Shenyang Tel: 86-24-2334-2829 Fax: 86-24-2334-2393 China - Shenzhen Tel: 86-755-8203-2660 Fax: 86-755-8203-1760 China - Shunde Tel: 86-757-2839-5507 Fax: 86-757-2839-5571 China - Wuhan Tel: 86-27-5980-5300 Fax: 86-27-5980-5118 China - Xian Tel: 86-29-8833-7250 Fax: 86-29-8833-7256 ASIA/PACIFIC India - Bangalore Tel: 91-80-2229-0061 Fax: 91-80-2229-0062 India - New Delhi Tel: 91-11-5160-8631 Fax: 91-11-5160-8632 India - Pune Tel: 91-20-2566-1512 Fax: 91-20-2566-1513 Japan - Yokohama Tel: 81-45-471- 6166 Fax: 81-45-471-6122 Korea - Gumi Tel: 82-54-473-4301 Fax: 82-54-473-4302 Korea - Seoul Tel: 82-2-554-7200 Fax: 82-2-558-5932 or 82-2-558-5934 Malaysia - Penang Tel: 60-4-646-8870 Fax: 60-4-646-5086 Philippines - Manila Tel: 63-2-634-9065 Fax: 63-2-634-9069 Singapore Tel: 65-6334-8870 Fax: 65-6334-8850 Taiwan - Hsin Chu Tel: 886-3-572-9526 Fax: 886-3-572-6459 Taiwan - Kaohsiung Tel: 886-7-536-4818 Fax: 886-7-536-4803 Taiwan - Taipei Tel: 886-2-2500-6610 Fax: 886-2-2508-0102 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 EUROPE Austria - Wels Tel: 43-7242-2244-399 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 France - Paris Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Germany - Munich Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781 Netherlands - Drunen Tel: 31-416-690399 Fax: 31-416-690340 Spain - Madrid Tel: 34-91-708-08-90 Fax: 34-91-708-08-91 UK - Wokingham Tel: 44-118-921-5869 Fax: 44-118-921-5820 10/31/05 DS80209D-page 16 (c) 2005 Microchip Technology Inc. |
Price & Availability of PIC18F4520 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |