View FAN5665_4111826.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

FAN5665 -- High-Efficiency, Adaptive Charge Pump 5V Boost
October 2007
FAN5665 High-Efficiency, Adaptive Charge Pump 5V Boost
Features
5V Fixed Output Voltage 30mA Maximum Output Current Built-in Charge Pump with Three Modes of Operation: 1x, 1.5x, and 2x Minimum External Components Flying Capacitors Only 0.22F Low-noise, Constant-frequency Operation (1.2MHz) at Heavy Loads High-efficiency, Low-frequency Operation at Light Loads Low Quiescent Current Up to 92% Efficiency 2.9V to 5.5V Input Voltage Range Soft-start for Limiting Inrush Current Input Under-Voltage Lockout Protection (UVLO) Short-Circuit Protection (SCP) Thermal Shutdown Protection (TSD) 8-bump 1.21 x 1.21mm, 0.4mm Pitch WLCSP
+5V C OUT 2.2F C2 0.22F VOUT C2+ C2C1C1 0.22F C1+ VIN C IN 2.2F GND EN +2.9 to 5.5V
Description
The FAN5665 is a 5V switched capacitor step-up DC/DC converter with an input voltage range from 2.9V to 5.5V. Switch reconfiguration and fractional switching techniques are utilized to achieve high efficiency over the entire input voltage range. The FAN5665 includes built-in under-voltage lockout, short circuit, and thermal protection circuitry. The FAN5665 is available in an 8-bump 0.4mm pitch WLCSP package.
Applications
USB I/O Supply Regulators Cell Phones, Smart-Phones Pocket PCs PDA, DSC, PMP, and MP3 Players Figure 1. Typical Application
Ordering Information
Part Number
FAN5665UCX
Operating Temperature Range
-40C to +85C
Package
8-Lead Wafer-Level Chip-Scale Package (WLCSP), 1.21x1.21mm
Packing Method
Tape and Reel
All packages are lead free per JEDEC: J-STD-020B standard.
(c) 2007 Fairchild Semiconductor Corporation FAN5665 * Rev. 1.0.0
www.fairchildsemi.com
FAN5665 -- High-Efficiency, Adaptive Charge Pump 5V Boost
Pin Configuration
Figure 2. Pin Configuration
Pin Definitions
Pin #
A1 A2 A3 B1 B3 C1 C2 C3
Name
C1GND EN C1+ VIN VOUT C2+ C2-
Description
Bucket capacitor 1. Connect this pin to the negative terminal of the bucket (flying) capacitor. Ground. Enable. Enables the IC when high. Disables the IC when low and enters shutdown mode. No internal pull-up or pull-down; this pin should not be left floating. Bucket capacitor 1. Connect this pin to the positive terminal of the bucket (flying) capacitor. Power input. Regulated 5V output. Bucket capacitor 2. Connect this pin to the positive terminal of the bucket (flying) capacitor. Bucket capacitor 2. Connect this pin to the negative terminal of the bucket (flying) capacitor.
(c) 2007 Fairchild Semiconductor Corporation FAN5665 * Rev. 1.0.0
www.fairchildsemi.com 2
FAN5665 -- High-Efficiency, Adaptive Charge Pump 5V Boost
Absolute Maximum Ratings
Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be operable above the recommended operating conditions and stressing the parts to these levels is not recommended. In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability. The absolute maximum ratings are stress ratings only.
Symbol
VIN TJ TSTG TL ESD VIN Pin
Parameter
EN, VOUT, C1+, C1-, C2+, C2- Pins Junction Temperature Storage Temperature Lead Soldering Temperature, 10 Seconds Human Body Model, JESD22-A114 Charged Device Model, JESD22-C101
Min.
-0.3 -0.3 -40 -65 3.5 2
Max.
+6.0 +6.0 +150 +150 +260
Unit
V V C C C kV
Recommended Operating Conditions
The Recommended Operating Conditions table defines the conditions for actual device operation. Recommended operating conditions are specified to ensure optimal performance to the datasheet specifications. Fairchild does not recommend exceeding them or designing to Absolute Maximum Ratings.
Symbol
VIN IOUT TA TJ CIN, COUT C1, C2 Output Current
Parameter
Power Supply Range Operating Ambient Temperature Range Operating Junction Temperature Range Input, output capacitor Bucket capacitor
Min.
2.9 0 -40 -40
Typ.
Max.
5.5 30 +85 +125
Unit
V mA C C F F
2.2 0.22
Thermal Properties
Symbol
JA
Parameter
Junction-to-Ambient Thermal Resistance
Min.
Typ.
170
(1)
Max.
Units
C/W
Note: 1. Junction-to-ambient thermal resistance is a function of application and board layout. This data is measured with four-layer boards in accordance with JESD51- JEDEC standard. Special attention must be paid not to exceed maximum junction temperature (TJ) at a given ambient temperate (TA).
(c) 2007 Fairchild Semiconductor Corporation FAN5665 * Rev. 1.0.0
www.fairchildsemi.com 3
FAN5665 -- High-Efficiency, Adaptive Charge Pump 5V Boost
Electrical Characteristics
Unless otherwise noted, VIN = 2.9V to 5.5V, C1 = C2 = 0.22F, CIN = 2.2F, COUT = 2.2F, TA = -40C to +85C, and test circuit is Figure 1. Typical values are at TA = 25C, VIN = 3.6V.
Symbol
Power Supplies ISD IDD VIH VIL IIH VHUVLO VLUVLO Regulation VOUT
Parameter
Shutdown Current Quiescent Current Enable High-level Input Voltage Enable Low-level Input Voltage Enable Pin Input Current Under-voltage Lockout High Threshold Under-voltage Lockout Low Threshold UVLO Hysteresis Voltage Accuracy
Conditions
VIN = 3.6V VIN = 3.6V, IOUT = 0mA VIN = 5.5V, IOUT = 0mA
Min.
Typ.
0.1 190 108
Max.
1.0 300 200 0.4
Units
A A V V A V V mV
1.1
EN = 1.8V VIN Rising VIN Falling 2.65 2.35
0.01
1.00 2.80 2.60
250 4.85 VIN = 3.6V, IOUT = 2mA VIN = 3.6V, IOUT = 30mA VOUT < 150mV Rising Temperature Hysteresis VIN = 3.6V, IOUT = 20mA VIN = 3.6V, IOUT = 2mA EN = 0 to 1 0.9 40 45 5.00 25 15 55 150 20 1.2 49 570 1.5 65 950
(2)
5.15
V mVpp
VOUT_RIPPLE Output Voltage Ripple ISC TSD Timing fOSC tss Internal Oscillator Frequency Soft-start Short-Circuit Current Limit Thermal Shutdown
80
mA C
MHz kHz s
Note: 2. Guaranteed by design.
(c) 2007 Fairchild Semiconductor Corporation FAN5665 * Rev. 1.0.0
www.fairchildsemi.com 4
FAN5665 -- High-Efficiency, Adaptive Charge Pump 5V Boost
Typical Performance Characteristics
Unless otherwise noted, CIN = 2.2F, COUT = 2.2F, C1 = C2 = 0.22F, TA = 25C.
50.5 Switching Frequency (kHz) 50.0 49.5 49.0 48.5 48.0 47.5 2.9 3.4 3.9 4.4 4.9 Input Voltage (V)
IOUT=2mA
1.2163 Switching Frequency (MHz)
1.2042
IOUT=20mA
1.1921
1.1800 2.9 3.4 3.9 4.4 4.9 Input Voltage (V)
Figure 3. Light-Load Switching Frequency vs. Input Voltage
Figure 4. Heavy-Load Switching Frequency vs. Input Voltage
80 Switching Frequecy (kHz)
Switching Frequecy (MHz)
1.34
70 60 50 40 30 20 10 0 -40
VIN=3.6V, IOUT=2mA
1.32 1.30 1.28 1.26 1.24 1.22 1.20 1.18 1.16 1.14 -40
VIN=3.6V, IOUT=20mA
-15
10
35
60
85
-15
10
35
60
85
Temperature (C)
Temperature (C)
Figure 5. Light-Load Switching Frequency vs. Temperature
Figure 6. Heavy-Load Switching Frequency vs. Temperature
250 Quiescent Current ( A) 200 150 100 50 0 2.9 3.4 3.9 4.4
Quiescent Current (A)
IOUT=0mA
300 250 200 150 100 50 0
VIN =5.5V
IOUT= 0mA
VIN =3.6V
4.9
5.4
-40
-15
10
35
60
85
Input Voltage (V)
Temperature (C)
Figure 7. Quiescent Current vs. Input Voltage
Figure 8. Quiescent Current vs. Temperature
(c) 2007 Fairchild Semiconductor Corporation FAN5665 * Rev. 1.0.0
www.fairchildsemi.com 5
FAN5665 -- High-Efficiency, Adaptive Charge Pump 5V Boost
Typical Performance Characteristics (Continued)
Unless otherwise noted, CIN = 2.2F, COUT = 2.2F, C1 = C2 = 0.22F, TA = 25C.
2.80 2.75 UVLO Threshold (V) 2.65 2.60 2.55 2.50 2.45 2.40 2.35 -40 -15 10 35 60 85 Temperature (C)
UVLO Rising UVLO Falling
5.06 5.04 Output Voltage (V) 5.02 5.00 4.98 4.96 4.94 4.92 4.90 0 5 10 15 20 25 30 Output Current (mA) VIN=2.9V VIN=4.2V VIN=5.5V
2.70
Figure 9. UVLO Threshold vs. Temperature
5.04 5.02 Output Voltage (V) 5.00 4.98 4.96 4.94 4.92 4.90 4.88 4.86 -40 -15 10 35 60 85 Temperature (C)
IOUT =20mA IOUT =30mA
Figure 10. Load Regulation
5.08 5.06 Output Voltage (V) 5.04 5.02 5.00 4.98 4.96 4.94 4.92 -40 -15 10 35 60 85 Temperature (C) IOUT=30mA IOUT=20mA V IN=4V
VIN=2.9V
IOUT =1mA
IOUT=1mA
Figure 11.
5.12 5.10 Output Voltage (V) 5.08 5.06 5.04 5.02 5.00 4.98 4.96 -40
Output Voltage vs. Temperature
Figure 12.
5.06 5.04 Output Voltage (V)
Output Voltage vs. Temperature
IOUT =0mA IOUT =20mA
VIN=5.5V
IOUT =1mA IOUT =20mA
5.02 5.00 4.98 4.96 4.94 4.92 4.90
IOUT =30mA
IOUT =30mA
-15
10
35
60
85
2.9
3.2
3.5
3.8
4.1
4.4
4.7
5
5.3
Temperature (C)
Input Voltage (V)
Figure 13. Output Voltage vs. Temperature
Iout = 1mA
Figure 14. Line Regulation
95 90 Efficiency (%) 85 80 75 70 65
VIN =2.9V VIN=4.3V VIN =5.5V
95 90 85 80 75 70 65 60 55 2.9 3.4 3.9 4.4 Input Voltage (V)
Iout = 5mA Iout = 10mA Iout = 20mA Iout = 30mA
Efficiency (%)
4.9
5.4
0
10
20
30
Output Current (mA)
Figure 15. Efficiency vs. Input Voltage
(c) 2007 Fairchild Semiconductor Corporation FAN5665 * Rev. 1.0.0
Figure 16. Efficiency vs. Output Current
www.fairchildsemi.com 6
FAN5665 -- High-Efficiency, Adaptive Charge Pump 5V Boost
Typical Performance Characteristics (Continued)
Unless otherwise noted, CIN = 2.2F, COUT = 2.2F, C1 = C2 = 0.22F, TA = 25C.
Figure 17. Load Transient from 0 to 30mA in 1x Mode
Figure 18. Load Transient from 30 to 0mA in 1x Mode
Figure 19. Load Transient from 0 to 30mA in 1.5x Mode
Figure 20. Load Transient from 30 to 0mA in 1.5x Mode
Figure 21. Load Transient from 0 to 20mA in 2x Mode
(c) 2007 Fairchild Semiconductor Corporation FAN5665 * Rev. 1.0.0 7
Figure 22. Load Transient from 20 to 0mA in 2x Mode
www.fairchildsemi.com
FAN5665 -- High-Efficiency, Adaptive Charge Pump 5V Boost
Typical Performance Characteristics (Continued)
Unless otherwise noted, CIN = 2.2F, COUT = 2.2F, C1 = C2 = 0.22F, TA = 25C.
Figure 23. Load Transient from 4 to 8mA in 2x Mode
Figure 24. Load Transient from 8 to 4mA in 2x Mode
Figure 25. Start-up at IOUT = 30mA in 1x Mode
Figure 26. Turn-off at IOUT = 30mA in 1x Mode
Figure 27. Start-up at IOUT = 30mA in 1.5x Mode
Figure 28. Turn-off at IOUT = 30mA in 1.5x Mode
(c) 2007 Fairchild Semiconductor Corporation FAN5665 * Rev. 1.0.0
www.fairchildsemi.com 8
FAN5665 -- High-Efficiency, Adaptive Charge Pump 5V Boost
Typical Performance Characteristics (Continued)
Unless otherwise noted, CIN = 2.2F, COUT = 2.2F, C1 = C2 = 0.22F, TA = 25C.
Figure 29. Start-up at IOUT = 30mA in 2x Mode
Figure 30. Turn-off at IOUT = 30mA in 2x Mode
Figure 31. Input and Output Ripple at IOUT = 30mA in 1.5x Mode
Figure 32. Input and Output Ripple at IOUT = 20mA in 1.5x Mode
Figure 33. Input and Output Ripple at IOUT = 30mA in 2x Mode
(c) 2007 Fairchild Semiconductor Corporation FAN5665 * Rev. 1.0.0 9
Figure 34. Input and Output Ripple at IOUT = 20mA in 2x Mode
www.fairchildsemi.com
FAN5665 -- High-Efficiency, Adaptive Charge Pump 5V Boost
Typical Performance Characteristics (Continued)
Unless otherwise noted, CIN = 2.2F, COUT = 2.2F, C1 = C2 = 0.22F, TA = 25C.
Figure 35. Input and Output Ripple at IOUT = 2mA in 1.5x Mode
Figure 36. Input and Output Ripple at IOUT = 2mA in 2x Mode
Figure 37. Line Transient 600mV Rising
Figure 38. Line Transient 600mV Falling
(c) 2007 Fairchild Semiconductor Corporation FAN5665 * Rev. 1.0.0
www.fairchildsemi.com 10
FAN5665 -- High-Efficiency, Adaptive Charge Pump 5V Boost
Block Diagram
Figure 39. Block Diagram
Functional Description
Overview
FAN5665 is a 5V switched capacitor regulator with very low output ripple and high efficiency. The maximum output current is 30mA.
Light / Heavy Load Monitor
In 1.5x / 2x mode, there is a current sense to detect the output current. If a light-load condition is detected, the device switches to a lower switching frequency around 50kHz. This frequency is a good compromise between achieving high light-load efficiency and not causing audible noise generation. If the load is heavy (typically more than 5mA), the device switches at 1.2MHz to decrease the output voltage ripple.
Linear Regulation Loop
The linear regulation loop (consisting of the power transistors, output feedback, and error amplifier), is used to regulate the output voltage and reduce current spikes at mode change.
Protection
FAN5665 has thermal shutdown protection when the die temperature is more than 150C. It turns back off when the temperature falls by about 10C. Short-circuit protection helps avoid damage to the device when the output is shorted to ground. Whenever output voltage is pulled below 150mV, short-circuit protection is triggered and limits the input current. If VOUT>150mV, protection is in the form of thermal shutdown if die temperature exceeds 150C.
www.fairchildsemi.com 11
Soft-start
At power-up, the device has 0.5ms soft-start to control the inrush current and make the output ramp up slowly.
Modes of Operation
FAN5665 has 1x, 1.5x, and 2x modes. Input voltage is compared with reference to determine mode.
(c) 2007 Fairchild Semiconductor Corporation FAN5665 * Rev. 1.0.0
FAN5665 -- High-Efficiency, Adaptive Charge Pump 5V Boost
Applications Information
The high switching frequency of 1.2MHz allows the use of small capacitors, but the material of the capacitor affects the input and output ripple, so the low-ESR capacitors are desirable. Another parameter affected by ESR is the efficiency. For proper operation, two ceramic bucket capacitors, along with one ceramic input capacitor and one ceramic output capacitor, are recommended (as shown in Figure 1).
Bucket Capacitor Selection
The bucket (flying) capacitor is usually the smallest capacitor in a charge pump circuit, but its ESR can play a significant role in determining the output voltage tolerance. Only ceramic capacitors are recommended in this position. The flying capacitance is determined by the switching frequency. At 1.2MHz, 0.22F flying capacitors are suitable for most applications, but can be increased to improve the output tolerance. Depending on the material of the multilayer ceramic capacitor, a substantial amount of capacitance may be lost over a wide temperature range. At least X5R and X7R capacitors are recommended for their relatively stable temperature characteristics. Z5U- or Y5V-type capacitors are not recommended. The following table shows a typical recommended bucket capacitor.
Input Capacitor Selection
In general, the ripple on the input power rail also affects the output ripple. The lower the ESR of the input capacitor, the lower the input and output ripple. The input capacitor may need to be adjusted, both in its value and in its physical placement on the PCB, depending upon the characteristics of the voltage source proving the input power. In general, a 1 to 2F ceramic capacitor placed close to the FAN5665 suffices. X5R and X7R capacitors provide adequate performance over -40C to +85C. The following table represents typical recommended input capacitors.
Description
Part Number
Vendor
Murata
Description
Capacitor 2.2F, 10%, 6.3V, X5R, 0603 Capacitor 2.2F, 20%, 6.3V, X5R, 0402
Part Number
GRM188R60J225KE19D
Vendor
Murata
Capacitor 0.22F, 10%, GRM155R60J224KE01D 6.3V, X5R, 0402
Increasing Output Current Capability
Two parallel FAN5665s increase the output current. In such a configuration, the VIN, VOUT, GND, and EN pins of each IC should be connected together, but the respective C1 and C2 pins must be kept separate. Separate local input and output bypassing / decoupling may be required to reduce output noise and ripple.
EN VOUT C1+ C1VIN GND C2C2+ C2
0.22F
GRM155R60J225ME15D
Murata
Output Capacitor Selection
In general, multilayer ceramic capacitors are recommended for low ESR. The value of the output bulk capacitance in relation to the switching frequency of the converter also determines the overall output voltage ripple. A higher value of output capacitance reduces the voltage droop during load transients. Typically, the output capacitor can be 5 to 50 times larger than the bucket capacitor(s), depending on the desired output ripple tolerance. Both X5R- and X7R-rated capacitors provide adequate performance over a -40C to +85C temperature range. The following table contains typical recommended output capacitors.
COUT
2.2F
CIN
2.2F
2.9 to5.5V V BAT
C1
0.22F
EN +5V COUT
2.2F
EN VOUT C1+ C1-
VIN GND C2C2+
CIN
2.2F
C1
0.22F
C2
0.22F
Description
Capacitor 2.2F, 10%, 6.3V, X5R, 0603 Capacitor 2.2F, 20%, 6.3V, X5R, 0402
Part Number
GRM188R60J225KE19D
Vendor
Figure 40. Two FAN5665s in Parallel Murata
GRM155R60J225ME15D
Murata
(c) 2007 Fairchild Semiconductor Corporation FAN5665 * Rev. 1.0.0
www.fairchildsemi.com 12
FAN5665 -- High-Efficiency, Adaptive Charge Pump 5V Boost
Applications Information (Continued)
LED Driver
The FAN5665 can be configured as an LED driver, as shown in Figure 41. The constant current is generated by putting a resistor in series with the LED. The value of series resistor is dictated by the current through the LED. The maximum current that the FAN5665 can deliver is 30mA. The number of parallel branches and current through LEDs should be chosen according to the maximum output current.
VIN C IN 2.2F GND C2C2+ VOUT C1+ C1C OUT 2.2F C1 0.22F RS EN Enable VOUT=5V
PCB Layout
The PCB layout should be designed carefully due to the high switching frequency and corresponding transient currents. All the external capacitors should be connected very close to the pins of the IC. A clean board layout with a good ground plane ensures proper operation of the device. A PCB recommendation for a two-layer board is shown in Figure 42. Note that the bottom layer is a dedicated ground plane.
ILED=10mA
ILED=10mA
RS
C2 0.22F
Figure 41. LED Driver Example Circuit
Figure 42. PCB Layout
(c) 2007 Fairchild Semiconductor Corporation FAN5665 * Rev. 1.0.0
www.fairchildsemi.com 13
FAN5665 -- High-Efficiency, Adaptive Charge Pump 5V Boost
Physical Dimensions
Product
FAN5665UC5X
D
1.210 +/- 0.030mm
E
1.210 +/- 0.030mm
X
0.205mm
Y
0.205mm
Figure 43. 8-Lead Wafer-Level Chip-Scale Package (WLCSP), 1.21x1.21mm
(c) 2007 Fairchild Semiconductor Corporation FAN5665 * Rev. 1.0.0
www.fairchildsemi.com 14
FAN5665 -- High-Efficiency, Adaptive Charge Pump 5V Boost
TRADEMARKS The following are registered and unregistered trademarks and service marks Fairchild Semiconductor owns or is authorized to use and is not intended to be an exhaustive list of all such trademarks. ACEx(R) Build it NowTM CorePLUSTM CROSSVOLTTM CTLTM Current Transfer LogicTM EcoSPARK(R)
(R)
Fairchild(R) Fairchild Semiconductor(R) FACT Quiet SeriesTM FACT(R) FAST(R) FastvCoreTM FPSTM FRFET(R) Global Power ResourceSM
Green FPSTM Green FPSTM e-SeriesTM GTOTM i-LoTM IntelliMAXTM ISOPLANARTM MegaBuckTM MICROCOUPLERTM MicroFETTM MicroPakTM MillerDriveTM Motion-SPMTM OPTOLOGIC(R) OPTOPLANAR(R)
(R)
PDP-SPMTM Power220(R)
Power247(R) POWEREDGE(R) Power-SPMTM PowerTrench(R) Programmable Active DroopTM QFET(R) QSTM QT OptoelectronicsTM Quiet SeriesTM RapidConfigureTM SMART STARTTM SPM(R) STEALTHTM SuperFETTM SuperSOTTM-3 SuperSOTTM-6
SuperSOTTM-8 SyncFETTM The Power Franchise(R) TinyBoostTM TinyBuckTM TinyLogic(R) TINYOPTOTM TinyPowerTM TinyPWMTM TinyWireTM SerDesTM UHC(R) UniFETTM VCXTM
DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION, OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. THESE SPECIFICATIONS DO NOT EXPAND THE TERMS OF FAIRCHILD'S WORLDWIDE TERMS AND CONDITIONS, SPECIFICALLY THE WARRANTY THEREIN, WHICH COVERS THESE PRODUCTS.
LIFE SUPPORT POLICY FAIRCHILD'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user. PRODUCT STATUS DEFINITIONS Definition of Terms Datasheet Identification Advance Information Preliminary Product Status Formative or In Design First Production Definition This datasheet contains the design specifications for product development. Specifications may change in any manner without notice. This datasheet contains preliminary data; supplementary data will be published at a later date. Fairchild Semiconductor reserves the right to make changes at any time without notice to improve design. This datasheet contains final specifications. Fairchild Semiconductor reserves the right to make changes at any time without notice to improve design. This datasheet contains specifications on a product that has been discontinued by Fairchild Semiconductor. The datasheet is printed for reference information only.
Rev. I31
2. A critical component in any component of a life support, device, or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness.
No Identification Needed
Full Production
Obsolete
Not In Production
(c) 2007 Fairchild Semiconductor Corporation FAN5665 * Rev. 1.0.0
www.fairchildsemi.com 15

▲Up To Search▲

Price & Availability of FAN5665

	To Download FAN5665 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .