Part Number Hot Search : 
FFV36AK 20N36 RF2105 RAPH2SG 08100 FCX61903 6EJMS1 60040215
Product Description
Full Text Search
 

To Download TB62726AFG Datasheet File

  If you can't view the Datasheet, Please click here to try to view without PDF Reader .  
 
 


  Datasheet File OCR Text:
 TB62726ANG/AFG
TOSHIBA Bi-CMOS Integrated Circuit Silicon Monolithic
TB62726ANG,TB62726AFG
16-bit Constant-Current LED Driver with Operating Voltage of 3.3-V and 5-V
The TB62726A series are comprised of constant-current drivers designed for LEDs and LED displays. The output current value can be set using an external resistor. As a result, all outputs will have virtually the same current levels. This driver incorporates 16-bit constant-current outputs, a 16-bit shift register, a 16-bit latch and a 16-bit AND-gate circuit. These drivers have been designed using the Bi-CMOS process. The suffix (G) appended to the part number represents a Lead(Pb)-Free product.
TB62726ANG
TB62726AFG
Features
* * * * * * * * * * * Output current capability and number of outputs: 90 mA x 16 outputs Constant current range: 2 to 90 mA Application output voltage: 0.7 V (output current 2 to 80 mA) 0.4 V (output current 2 to 40 mA) For anode-common LEDs Input signal voltage level: 3.3-V and 5-V CMOS level (Schmitt trigger input) Power supply voltage range VDD = 3.0 to 5.5 V Maximum output terminal voltage: 17 V Serial and parallel data transfer rate: 20 MHz (max, cascade connection) Operating temperature range Topr = -40 to 85C Package: Type ANG: SDIP24-P-300-1.78 Type AFG: SSOP24-P-300-1.00B Current accuracy (All output ON)
Output Voltage > 0.4 V = > 0.7 V = Current Accuracy Between Bits 4% Between ICs 15% 12% 2 to 5 mA 5 to 80 mA Output Current
Weight SDIP24-P-300-1.78: 1.22 g (typ.) SSOP24-P-300-1.00B: 0.32 g (typ.)
1
2006-06-14
TB62726ANG/AFG
Pin Assignment (top view)
GND SERIAL-IN CLOCK LATCH OUT0 OUT1 OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 VDD R-EXT SERIAL-OUT ENABLE OUT15 OUT14 OUT13 OUT12 OUT11 OUT10 OUT9 OUT8
Warnings: Short-circuiting an output terminal to GND or to the power supply terminal may broken the device. Please take care when wiring the output terminals, the power supply terminal and the GND terminals.
Block Diagram
OUT0
OUT1 OUT15
R-EXT
I-REG
ENABLE Q ST LATCH D ST Q D ST Q D
SERIAL-IN
D CK
Q
D CK
Q
D CK
Q
SERIAL-OUT
CLOCK
Truth Table
CLOCK
LATCH
ENABLE
SERIAL-IN
OUT0 ... OUT7 ... OUT15 Dn ... Dn - 7 ... Dn - 15 No change Dn + 2 ... Dn - 5 ... Dn - 13 Dn + 2 ... Dn - 5 ... Dn - 13 OFF
SERIAL-OUT Dn - 15 Dn - 14 Dn - 13 Dn - 13 Dn - 13
H L H X X
L L L L H
Dn Dn + 1 Dn + 2 Dn + 3 Dn + 3
Note 1:
OUT0 to OUT15 = On when Dn = H; OUT0 to OUT15 = Off when Dn = L. In order to ensure that the level of the power supply voltage is correct, an external resistor must be connected between R-EXT and GND.
2
2006-06-14
TB62726ANG/AFG
Timing Diagram
n=0 CLOCK 0V 3.3 V/5 V SERIAL-IN 0V 3.3 V/5 V LATCH 0V 3.3 V/5 V 0V On 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 3.3 V/5 V
ENABLE
OUT0
Off On
OUT1
Off On
OUT3
Off
On OUT15 Off 3.3 V/5 V SERIAL-OUT 0V
Warning: Latch circuit is leveled-latch circuit. Be careful because it is not triggered-latch circuit. Note 2: The latches circuit holds data by pulling the LATCH terminal Low. And, when LATCH terminal is a High level, latch circuit doesn't hold data, and it passes from the input to the output. When ENABLE terminal is a Low level, output terminal OUT0 to OUT15 respond to the data, and on and off does. And, when ENABLE terminal is a High level, it offs with the output terminal regardless of the data.
3
2006-06-14
TB62726ANG/AFG
Terminal Description
Pin No. 1 2 3 4 5 to 20 Pin Name GND SERIAL-IN CLOCK LATCH GND terminal for control logic Input terminal for serial data for data shift register Input terminal for clock for data shift on rising edge Input terminal for data strobe When the LATCH input is driven High, data is not latched. When it is pulled Low, data is latched. Function
OUT0 to OUT15 Constant-current output terminals Input terminal for output enable.
21
ENABLE
All outputs ( OUT0 to OUT15 ) are turned off, when the ENABLE terminal is driven High. And are turned on, when the terminal is driven Low.
22 23 24
SERIAL-OUT R-EXT VDD
Output terminal for serial data input on SERIAL-IN terminal Input terminal used to connect an external resistor. This regulated the output current. 3.3-V/5-V supply voltage terminal
Equivalent Circuits for Inputs and Outputs
1. ENABLE terminal
R (UP) VDD
2. LATCH terminal
VDD
LATCH ENABLE
GND GND R (DOWN)
3. CLOCK, SERIAL-IN terminal
VDD
4. SERIAL-OUT terminal
VDD
CLOCK, SERIAL-IN
SERIAL-OUT Internal data
GND
GND
5. OUT0 to OUT15 terminals
OUT0 to OUT15
Parasitic Diode GND
4
2006-06-14
TB62726ANG/AFG
Absolute Maximum Ratings (Topr = 25C)
Characteristics Supply voltage Input voltage Output current Output voltage ANG-type (when not mounted) Power dissipation ANG-type (on PCB) (Note 3) AFG-type (when not mounted) AFG-type (on PCB) ANG-type (when not mounted) Thermal resistance ANG-type (on PCB) (Note 3) AFG-type (when not mounted) AFG-type (on PCB) Operating temperature Storage temperature Topr Tstg Symbol VDD VIN IOUT VOUT Pd1 1.78 W 0.83 Pd2 1.00 104 Rth (j-a) 1 70 C/W 140 Rth (j-a) 2 120 Rating 6 Unit V V mA/ch V
-0.2 to VDD + 0.2 +90 -0.2 to 17
1.25
-40 to 85 -55 to 150
C C
Note 3: ANG-Type: Powers dissipation is derated by 14.28 mW/C if device is mounted on PCB and ambient temperature is above 25C. AFG-Type: Powers dissipation is derated by 6.67 mW/C if device is mounted on PCB and ambient temperature is above 25C. With device mounted on glass-epoxy PCB of less than 40% Cu and of dimensions 50 mm x 50 mm x 1.6 mm.
Recommended Operating Conditions (Topr = -40C to 85C unless otherwise specified)
Characteristics Supply voltage Output voltage Symbol VDD VOUT IOUT Output current IOH IOL VIH Input voltage VIL Clock frequency LATCH pulse width CLOCK pulse width ENABLE pulse width (Note 4) Set-up time for CLOCK terminal Hold time for CLOCK terminal Set-up time for LATCH terminal fCLK twLAT twCLK twENA tSETUP1 tHOLD tSETUP2 Cascade connected Each DC 1 circuit SERIAL-OUT SERIAL-OUT Conditions Min 3 Typ. Max 5.5 4 80 Unit V V mA/ch mA

0.7
2


0.7 x VDD
-1
1 VDD + 0.15 0.3 x VDD 20
V
-0.15
50
MHz ns ns ns ns ns ns

Upper IOUT = 20 mA Lower IOUT = 20 mA
25 2000 3000 10
10 50
Note 4: When the pulse of the Low level is inputted to the ENABLE terminal held in the High level.
5
2006-06-14
TB62726ANG/AFG
Electrical Characteristics (Topr = 25C, VDD = 3.0 V to 5.5 V unless otherwise specified)
Characteristics Supply voltage Symbol VDD IOUT1 IOUT2 Output current IOUT3 IOUT4 Conditions Normal operation VOUT = 0.4 V, VDD = 3.3 V VOUT = 0.4 V, VDD = 5 V VOUT = 0.7 V, VDD = 3.3 V VOUT = 0.7 V, VDD = 5 V VOUT 0.4 V, All outputs ON VOUT 0.4 V, All outputs ON VOUT = 15.0 V Min 3.0 31.96 REXT = 490 31. 59 63.63 REXT = 250 62.75 REXT = 490 71.30 79.95 35.90 72.30 40.20 mA 80.97 Typ. Max 5.5 40.54 Unit V
36.20
IOUT1
Output current error between bits
REXT = 250
1
4
%
IOUT2
Output leakage current input voltage IOZ

0.7 VDD GND
-1
1 VDD
A
Input voltage
VIN
V 0.3 VDD 0.3 0.3 V
IOL = 1.0 mA, VDD = 3.3 V IOL = 1.0 mA, VDD = 5 V IOH = - 1.0 mA, VDD = 3.3 V IOH = 1.0 mA, VDD = 5 V When VDD is changed 3 V to 5.5 V ENABLE terminal
VOL SOUT terminal voltage VOH Output current Supply voltage Regulation Pull-up resistor Pull-down resistor

3 4.7
-5
%/VDD R (Up) R (Down) IDD (OFF) 1 IDD (OFF) 2 IDD (OFF) 3
%
115 LATCH terminal VOUT = 15.0 V VOUT = 15.0 V, All outputs OFF VOUT = 15.0 V, All outputs OFF VOUT = 0.7 V, All outputs ON REXT = OPEN REXT = 490 REXT = 250 REXT = 490
230 0.1 3.5 6 9
460 0.5 5 9 15 20 25 40
k
1 4
Supply current IDD (ON) 1

mA
Same as the above, Topr = -40C IDD (ON) 2 VOUT = 0.7 V, All outputs ON REXT = 250
18
Same as the above, Topr = -40C
6
2006-06-14
TB62726ANG/AFG
Switching Characteristics (Topr = 25C unless otherwise specifed)
Characteristics Symbol tpLH1 Conditions CLK- OUTn , LATCH = "H", Min Typ. Max Unit
ENABLE = "L" LATCH - OUTn , ENABLE = "L" ENABLE - OUTn , LATCH = "H" CLK-SERIAL OUT CLK- OUTn , LATCH = "H", ENABLE = "L" LATCH - OUTn , ENABLE = "L" ENABLE - OUTn , LATCH = "H" CLK-SERIAL OUT 10 to 90% of voltage waveform 90 to 10% of voltage waveform When not on PCB (Note 5)

3
150
300
tpLH2 tpLH3 tpLH tpHL1 tpHL2 tpHL3 tpLH Output rise time Output fall time Maximum CLOCK rise time Maximum CLOCK fall time tor tof tr tf
140
300
140 6 170
300
Propagation delay
340
ns

4 40 40
170
340
170 7 85 70
340
150 150 5 5 ns ns


s s
Conditions: (Refer to test circuit.) Topr = 25C, VDD = VIH = 3.3 V and 5 V, VOUT = 0.7 V, VIL = 0 V, REXT = 490 , VL = 3.0 V, RL = 60 , CL = 10.5 pF Note 5: If the device is connected in a cascade and tr/tf for the waveform is large, it may not be possible to achieve the timing required for data transfer. Please consider the timings carefully.
Test Circuit
IDD
VIH, VIL
ENABLE CLOCK
VDD
RL OUT0 CL
Function generator
IOL LATCH SERIAL-IN SERIAL-OUT R-EXT GND CL Iref VL OUT15
Logic input waveform
VDD = VIH = 3.3 V VIL = 0 V tr = tf = 10 ns (10% to 90%)
7
2006-06-14
TB62726ANG/AFG
Timing Waveforms
1. CLOCK, SERIAL-IN, SERIAL-OUT
twCLK CLOCK 50% tSETUP1 SERIAL-IN 50% tHOLD SERIAL-OUT 50% tpLH/tpHL 50% 50%
2. CLOCK, SERIAL-IN, LATCH , ENABLE , OUTn
CLOCK
50%
SERIAL-IN tSETUP2 LATCH 50% twLAT ENABLE tSETUP3 50% 50% twENA 50%
OUTn tpHL1/LH1 tpHL2/LH2
50%
tpHL3/LH3
3. OUTn
90% OUTn 10% tof 10% tor ON 90% OFF
8
2006-06-14
TB62726ANG/AFG
Output Current - Duty (LEDS turn-on rate)
IOUT - DUTY On PCB
100 100
IOUT - DUTY On PCB
80
80
(mA)
60
(mA) IOUT
Topr = 25C VDD = 3.3 V to 5.0 V VCE = 1.0 V Tj = 120C (max)
60
IOUT
40
40 Topr = 55C VDD = 3.3 V to 5.0 V VCE = 1.0 V Tj = 120C (max) 0 0 20 40 60
20
20 TB62726AFG TB62726ANG
TB62726AFG TB62726ANG 80 100
0 0
20
40
60
80
100
DUTY - Turn On Rate
(%)
DUTY - Turn On Rate
(%)
IOUT - DUTY On PCB
100 2.0 1.8 NG (On PCB)
Pd - Topr
(W/IC) PD
80
1.6 1.4 1.2 FG (On PCB) 1.0 0.8 0.6 0.4 0.2
(mA)
60
40 Topr = 85C VDD = 3.3 V to 5.0 V VCE = 1.0 V Tj = 120C (max) 0 0 20 40 60
20
TB62726AFG TB62726ANG 80 100 0 0 20 40 60 80 100
Power dissipation
IOUT
DUTY - Turn On Rate
(%)
Ambient temperature
Ta
(C)
Output Current - REXT Resistor
IOUT - REXT
90 Theoretical value: 80 70 60 IOUT = (1.15 (V) / R-EXT ()) x 14.9
(mA) IOUT
50 40 Topr = 25C 30 20 10 VCE = 0.7 V 0 100 500 1000 5000 10000
REXT ()
9
2006-06-14
TB62726ANG/AFG
Application Circuit (example 1): The general composition in static lighting of LED.
More than VLED (V) Vf (total max) + 0.7 is recommended with the following application circuit with the LED power supply VLED.
r1: The setup resistance for the setup of output current of every IC. r2: The variable resistance for the brightness control of every LED module.
Example) TD62M8600F: 8-bit multi-chip PNP transistor array, which is not used in static lighting system.
VLED
SCAN
O0
SERIAL-IN C.U. ENABLE LATCH CLOCK
O1
O2
O13
O14
O15 SERIAL-IN SERIAL-OUT ENABLE LATCH
O0
O1
O2
O13 O14 O15 SERIAL-OUT
16-bit SIPO, Latches and Constant-sink-current drivers
16-bit SIPO, Latches and Constant-sink-current drivers
TB62726ANG/AFG
CLOCK
TB62726ANG/AFG
r1 = 100 (min) r2 r1 = 100 (min)
10
2006-06-14
TB62726ANG/AFG
Application Circuit (example 2): When the condition of VLED is VLED > 17 V
The unnecessary voltage is one effective technique as to making the voltage descend with the zenor diode.
Example) TD62M8600F: 8-bit multi-chip PNP transistor array, which is not used in static lighting system.
VLED > 17 V
SCAN O0 SERIAL-IN C.U. ENABLE LATCH CLOCK TB62726ANG/AFG 16-bit SIPO, Latches and Constant-sink-current drivers O1
O2
O13
O14
O15 SERIAL-IN SERIAL-OUT ENABLE LATCH CLOCK
O0
O1
O2
O13 O14 O15 SERIAL-OUT
16-bit SIPO, Latches and Constant-sink-current drivers
TB62726ANG/AFG
r1 = 100 (min) r2 r1 = 100 (min)
11
2006-06-14
TB62726ANG/AFG
Application Circuit (example 3): When the condition of VLED is Vf +0.7 < VLED < 17 V
VOUT = VLED-Vf = 0.7 to 1.0 V is the most suitable for VOUT. Surplus VOUT causes an IC fever and the useless consumption electric power. It is the one way of being effective to build in the r3 in this problem. r3 can make a calculation to the formula r3 = surplus VOUT/IOUT. Though the resistance parts increase, the fixed constant current performance is kept
Example) TD62M8600F: 8-bit multi-chip PNP transistor array, which is not used in static lighting system.
r3
r3
VLED = 15 V
SCAN
O0
SERIAL-IN C.U. ENABLE LATCH CLOCK
O1
O2
O13
O14
O15 SERIAL-IN SERIAL-OUT LATCH
O0
O1
O2
O13 O14 O15 SERIAL-OUT
16-bit SIPO, Latches and Constant-sink-current drivers
16-bit SIPO, Latches and Constant-sink-current drivers
TB62726ANG/AFG
CLOCK
TB62726ANG/AFG
r1 = 100 (min) r2 r1 = 100 (min)
12
2006-06-14
TB62726ANG/AFG
Notes
* Operation may become unstable due to the electromagnetic interference caused by the wiring and other phenomena. To counter this, it is recommended that the IC be situated as close as possible to the LED module. If overvoltage is caused by inductance between the LED and the output terminals, both the LED and the terminals may suffer damage as a result. There is only one GND terminal on this device when the inductance in the GND line and the resistor are large, the device may malfunction due to the GND noise when output switchings by the circuit board pattern and wiring. To achieve stable operation, it is necessary to connect a resistor between the REXT terminal and the GND line. Fluctuation in the output waveform is likely to occur when the GND line is unstable or when a capacitor (of more than 50 pF) is used. Therefore, take care when designing the circuit board pattern layout and the wiring from the controller. This application circuit is a reference example and is not guaranteed to work in all conditions. Be sure to check the operation of your circuits. This device does not include protection circuits for overvoltage, overcurrent or overtemperature. If protection is necessary, it must be incorporated into the control circuitry. The device is likely to be destroyed if a short-circuit occurs between either of the power supply pins and any of the output terminals when designing circuits, pay special attention to the positions of the output terminals and the power supply terminals (VDD and VLED), and to the design of the GND line.
*
*
*
*
13
2006-06-14
TB62726ANG/AFG
Package Dimensions
Weight: 1.22 g (typ.)
14
2006-06-14
TB62726ANG/AFG
Package Dimensions
Weight: 0.32 g (typ.)
15
2006-06-14
TB62726ANG/AFG
Notes on Contents
1. Block Diagrams
Some of the functional blocks, circuits, or constants in the block diagram may be omitted or simplified for explanatory purposes.
2. Equivalent Circuits
The equivalent circuit diagrams may be simplified or some parts of them may be omitted for explanatory purposes.
3. Timing Charts
Timing charts may be simplified for explanatory purposes.
4. Application Circuits
The application circuits shown in this document are provided for reference purposes only. Thorough evaluation is required, especially at the mass production design stage. Toshiba does not grant any license to any industrial property rights by providing these examples of application circuits.
5. Test Circuits
Components in the test circuits are used only to obtain and confirm the device characteristics. These components and circuits are not guaranteed to prevent malfunction or failure from occurring in the application equipment.
IC Usage Considerations
Notes on Handling of ICs
(1) The absolute maximum ratings of a semiconductor device are a set of ratings that must not be exceeded, even for a moment. Do not exceed any of these ratings. Exceeding the rating(s) may cause the device breakdown, damage or deterioration, and may result injury by explosion or combustion. Use an appropriate power supply fuse to ensure that a large current does not continuously flow in case of over current and/or IC failure. The IC will fully break down when used under conditions that exceed its absolute maximum ratings, when the wiring is routed improperly or when an abnormal pulse noise occurs from the wiring or load, causing a large current to continuously flow and the breakdown can lead smoke or ignition. To minimize the effects of the flow of a large current in case of breakdown, appropriate settings, such as fuse capacity, fusing time and insertion circuit location, are required. If your design includes an inductive load such as a motor coil, incorporate a protection circuit into the design to prevent device malfunction or breakdown caused by the current resulting from the inrush current at power ON or the negative current resulting from the back electromotive force at power OFF. IC breakdown may cause injury, smoke or ignition. Use a stable power supply with ICs with built-in protection functions. If the power supply is unstable, the protection function may not operate, causing IC breakdown. IC breakdown may cause injury, smoke or ignition. Do not insert devices in the wrong orientation or incorrectly. Make sure that the positive and negative terminals of power supplies are connected properly. Otherwise, the current or power consumption may exceed the absolute maximum rating, and exceeding the rating(s) may cause the device breakdown, damage or deterioration, and may result injury by explosion or combustion. In addition, do not use any device that is applied the current with inserting in the wrong orientation or incorrectly even just one time.
(2)
(3)
(4)
16
2006-06-14
TB62726ANG/AFG
(5) Carefully select external components (such as inputs and negative feedback capacitors) and load components (such as speakers), for example, power amp and regulator. If there is a large amount of leakage current such as input or negative feedback condenser, the IC output DC voltage will increase. If this output voltage is connected to a speaker with low input withstand voltage, overcurrent or IC failure can cause smoke or ignition. (The over current can cause smoke or ignition from the IC itself.) In particular, please pay attention when using a Bridge Tied Load (BTL) connection type IC that inputs output DC voltage to a speaker directly.
17
2006-06-14
TB62726ANG/AFG
Points to Remember on Handling of ICs
(1) Heat Radiation Design In using an IC with large current flow such as power amp, regulator or driver, please design the device so that heat is appropriately radiated, not to exceed the specified junction temperature (Tj) at any time and condition. These ICs generate heat even during normal use. An inadequate IC heat radiation design can lead to decrease in IC life, deterioration of IC characteristics or IC breakdown. In addition, please design the device taking into considerate the effect of IC heat radiation with peripheral components. Back-EMF When a motor rotates in the reverse direction, stops or slows down abruptly, a current flow back to the motor's power supply due to the effect of back-EMF. If the current sink capability of the power supply is small, the device's motor power supply and output pins might be exposed to conditions beyond absolute maximum ratings. To avoid this problem, take the effect of back-EMF into consideration in system design.
(2)
18
2006-06-14
TB62726ANG/AFG
About solderability, following conditions were confirmed
* Solderability
(1) Use of Sn-37Pb solder Bath * solder bath temperature = 230C * dipping time = 5 seconds * the number of times = once * use of R-type flux (2) Use of Sn-3.0Ag-0.5Cu solder Bath * solder bath temperature = 245C * dipping time = 5 seconds * the number of times = once * use of R-type flux
RESTRICTIONS ON PRODUCT USE
* The information contained herein is subject to change without notice. 021023_D
060116EBA
* TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the "Handling Guide for Semiconductor Devices," or "TOSHIBA Semiconductor Reliability Handbook" etc. 021023_A * The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.). These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury ("Unintended Usage"). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc. Unintended Usage of TOSHIBA products listed in this document shall be made at the customer's own risk. 021023_B * The products described in this document shall not be used or embedded to any downstream products of which manufacture, use and/or sale are prohibited under any applicable laws and regulations. 060106_Q * The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of TOSHIBA or others.
021023_C
* The products described in this document are subject to the foreign exchange and foreign trade laws. 021023_E
19
2006-06-14


▲Up To Search▲   

 
Price & Availability of TB62726AFG

All Rights Reserved © IC-ON-LINE 2003 - 2022  

[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy]
Mirror Sites :  [www.datasheet.hk]   [www.maxim4u.com]  [www.ic-on-line.cn] [www.ic-on-line.com] [www.ic-on-line.net] [www.alldatasheet.com.cn] [www.gdcy.com]  [www.gdcy.net]


 . . . . .
  We use cookies to deliver the best possible web experience and assist with our advertising efforts. By continuing to use this site, you consent to the use of cookies. For more information on cookies, please take a look at our Privacy Policy. X