View EHP-5393-UT31C-P01_4200738.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Technical Data Sheet
Features
Popular 10mm package. Typical color temperature 6500K View angle:25 . High light flux output Soldering methods: Dip soldering. Grouping parameter: total luminous flux, color coordinates. Optical efficiency: 30 lm/W Thermal resistance (junction to lead): 13K/W The product itself will remain within RoHS compliant version. ESD-withstand voltage: up to 4KV
Preliminary
EHP-5393/UT31C-P01
Descriptions
The series is specially designed for applications requiring higher brightness. EHP-5393 is a revolution, energy efficient and ultra compact new light source, combining the lifetime and reliability advantages of Light Emitting Diodes with the brightness of conventional lighting.
Applications
Flash Sunshine light. Advertising Signs. Back lighting.
Device Selection Guide
LED Part No. Chip Material InGaN Emitted Color White Lens Color Water Clear
EHP-5393/UT31C-P01
Everlight Electronics Co., Ltd. Device Number :
http\\:www.everlight.com Prepared date:1-15-2008
Rev:
Page: 1 of 12
Prepared by: Dante Chen
Technical Data Sheet
Package Dimensions
Preliminary
EHP-5393/UT31C-P01
Notes:
Other dimensions are in millimeters, tolerance is 0.25mm except being specified. Protruded resin under flange is 1.5mm Max LED. Bare copper alloy is exposed at tie-bar portion after cutting.
Everlight Electronics Co., Ltd. Device Number :
http\\:www.everlight.com Prepared date:1-15-2008
Rev:
Prepared by: Dante Chen
edohtaC 2
edonA 1
1 . 5 0 . 2
2.01
2 0 . 2
1
3.001
3.001
2.01
1 2 . 5 4 0 . 3 1 . 5 0 . 2 M i n . 1 . 0
2
M i n . 1 5
3 . 8 8 0 . 3
M i n . 3 1
Page: 2 of 12
Technical Data Sheet
Absolute Maximum Rating (Ta=25)
Parameter Forward Current Junction to heat-sink thermal resistance Operating Temperature Storage Temperature Electrostatic Discharge Soldering Temperature Power Dissipation Reverse Voltage Zener Reverse Current Notes: Soldering time5 seconds. Symbol IF Rth Topr Tstg ESD Tsol Pd VR Iz
Preliminary
EHP-5393/UT31C-P01
Absolute Maximum Rating 350 13 -40 ~ +85 -40 ~ +100 4K 260 1.4 5 100 Unit mA K/W V W V mA
Electro-Optical Characteristics (Ta=25)
Parameter Luminous Flux Viewing Angle Forward Voltage Reverse Current Zener Reverse Voltage Color Temperature Chromaticity Coordinates Symbol Flux 21/2 VF IR Vz CCT x y Min. 33 --3.0 --5.2 4500 ----Typ. --25 3.5 ----6500 0.29 0.28 Max. 52 --4.0 10 --10000 ----Unit lm deg V A V K --IF=350mA --VR=5V Iz=5mA IF=350mA IF=350mA Condition
Everlight Electronics Co., Ltd. Device Number :
http\\:www.everlight.com Prepared date:1-15-2008
Rev:
Page: 3 of 12
Prepared by: Dante Chen
Technical Data Sheet
Preliminary
EHP-5393/UT31C-P01
Rank Combination (IF=350mA)
Rank Luminous Flux J3 33~39 J4 39~45 J5 45~52 K1 52~60
Unit:mcd
*Measurement Uncertainty of Luminous Intensity: 15%
Forward Voltage Combination (V at 350mA)
Rank Forward Voltage 1 3.0~3.2 2 3.2~3.4 3 3.4~3.6 4 3.6~3.8 5 3.8~4.0
Unit:V
*Measurement Uncertainty of Forward Voltage: 0.1V
Everlight Electronics Co., Ltd. Device Number :
http\\:www.everlight.com Prepared date:1-15-2008
Rev:
Page: 4 of 12
Prepared by: Dante Chen
Technical Data Sheet
Color Combination ( at 350mA)
Y6-1 Y9-1 Y6-2
Preliminary
EHP-5393/UT31C-P01
Y9-2
X Y X Y 0.283 0.284 0.29 0.27 0.274 0.301 0.283 0.284 0.281 0.309 0.289 0.291 0.289 0.291 0.295 0.276 Reference CCT: 9000~10000K Y6-3 Y9-3 X Y X Y 0.308 0.311 0.311 0.293 0.297 0.3 0.302 0.283 0.29 0.318 0.297 0.3 0.303 0.333 0.308 0.311 Reference CCT: 7000~8000K
X Y X Y 0.289 0.291 0.295 0.276 0.281 0.309 0.289 0.291 0.29 0.318 0.297 0.3 0.297 0.3 0.302 0.283 Reference CCT: 8000~9000K
X4 X 0.301 0.314 0.315 0.303 Y 0.342 0.355 0.344 0.333 X 0.305 0.303 0.315 0.316
X5
X6 X 0.308 0.317 0.319 0.311
X7 Y 0.311 0.32 0.3 0.293
Y X Y 0.322 0.308 0.311 0.333 0.305 0.322 0.344 0.316 0.333 0.333 0.317 0.32 Reference CCT: 6300~7000K
W4 X 0.329 0.329 0.315 0.314 Y 0.369 0.357 0.344 0.355 X 0.329 0.316 0.315 0.329
W5
W6 Y X Y X 0.345 0.329 0.345 0.329 0.333 0.329 0.331 0.329 0.344 0.317 0.32 0.318 0.357 0.316 0.333 0.317 Reference CCT: 5650~6300K
W7 Y 0.331 0.32 0.31 0.32 X 0.329 0.329 0.319 0.318
W8 Y 0.321 0.31 0.3 0.31
Everlight Electronics Co., Ltd. Device Number :
http\\:www.everlight.com Prepared date:1-15-2008
Rev:
Page: 5 of 12
Prepared by: Dante Chen
Technical Data Sheet
Preliminary
EHP-5393/UT31C-P01
V4 X 0.329 0.329 0.348 0.347 Y 0.357 0.369 0.385 0.372 X 0.329 0.329 0.347 0.346
V5
V6 X 0.329 0.344 0.343 0.329
V7 Y 0.331 0.344 0.331 0.32
Y X Y 0.345 0.329 0.331 0.357 0.329 0.345 0.372 0.346 0.359 0.359 0.344 0.344 Reference CCT: 5000~5650K
U4 X 0.364 0.367 0.348 0.347 Y 0.383 0.4 0.385 0.372
U5 X Y 0.364 0.383 0.362 0.372 0.346 0.359 0.347 0.372 Reference CCT: 4500~5000K X 0.362 0.36 0.344 0.346
U6 Y 0.372 0.357 0.344 0.359
CIE Chromaticity Diagram
Everlight Electronics Co., Ltd. Device Number :
http\\:www.everlight.com Prepared date:1-15-2008
Rev:
Page: 6 of 12
Prepared by: Dante Chen
Technical Data Sheet
Typical Electro-Optical Characteristics Curves
Preliminary
EHP-5393/UT31C-P01
Everlight Electronics Co., Ltd. Device Number :
http\\:www.everlight.com Prepared date:1-15-2008
Rev:
Page: 7 of 12
Prepared by: Dante Chen
Technical Data Sheet
Packing Specification
Anti-electrostatic bag
Preliminary
EHP-5393/UT31C-P01
EVERLIGHT
Label
CPN: P/N:XXXXXXXXXX
RoHS
XXX/XXXX-XXXX QTYXXXX
Inner Carton
Outside Carton
Everlight Electronics Co., Ltd. Device Number :
http\\:www.everlight.com Prepared date:1-15-2008

CITE NGA NORTCELE C IT ATS ORTCE LE
SDLER EV ITCA OI DAR RO C ITEN GAM
057 rof c itats- itna
bP
CAT:XX HUE:XX REF:XX
LOT NO XXXXXXXX MADE IN TAIWAN

Label Form Specification CPN: Customer's Production Number P/N : Production Number QTY: Packing Quantity CAT: Ranks of Total Flux and Forward Voltage HUE: Color Rank REF: Reference LOT No: Lot Number MADE IN TAIWAN: Production Place Packing Quantity 1. 250 PCS/1 Bag5 Bags/1 Inner Carton 2. 10 Inner Cartons/1 Outside Carton
Rev:
Page: 8 of 12
Prepared by: Dante Chen
Technical Data Sheet
Notes
Preliminary
EHP-5393/UT31C-P01
1. Lead Forming During lead formation, the leads should be bent at a point at least 3mm from the base of the epoxy bulb. Lead forming should be done before soldering. Avoid stressing the LED package during leads forming. The stress to the base may damage the LED's characteristics or it may break the LEDs. Cut the LED leadframes at room temperature. Cutting the leadframes at high temperatures may cause failure of the LEDs. When mounting the LEDs onto a PCB, the PCB holes must be aligned exactly with the lead position of the LED. If the LEDs are mounted with stress at the leads, it causes deterioration of the epoxy resin and this will degrade the LEDs. 2. Storage The LEDs should be stored at 30C or less and 70%RH or less after being shipped from Everlight and the storage life limits are 3 months. If the LEDs are stored for 3 months or more, they can be stored for a year in a sealed container with a nitrogen atmosphere and moisture absorbent material. Please avoid rapid transitions in ambient temperature, especially, in high humidity environments where condensation can occur. 3. Soldering Careful attention should be paid during soldering. When soldering, leave more then 3mm from solder joint to epoxy bulb, and soldering beyond the base of the tie bar is recommended. Recommended soldering conditions: Hand Soldering Temp. at tip of iron Soldering time Distance 300 Max. (30W Max.) 3 sec Max. 3mm Min.(From solder joint to epoxy bulb) Preheat temp. DIP Soldering 100 Max. (60 sec Max.) 3mm Min. (From solder joint to epoxy bulb)
Rev: Page: 9 of 12
Bath temp. & time 260 Max., 5 sec Max Distance
Everlight Electronics Co., Ltd. Device Number :
http\\:www.everlight.com Prepared date:1-15-2008
Prepared by: Dante Chen
Technical Data Sheet
Preliminary
EHP-5393/UT31C-P01
Avoiding applying any stress to the lead frame while the LEDs are at high temperature particularly when soldering. Dip and hand soldering should not be done more than one time After soldering the LEDs, the epoxy bulb should be protected from mechanical shock or vibration until the LEDs return to room temperature. A rapid-rate process is not recommended for cooling the LEDs down from the peak temperature. Although the recommended soldering conditions are specified in the above table, dip or handsoldering at the lowest possible temperature is desirable for the LEDs. Wave soldering parameter must be set and maintain according to recommended temperature and dwell time in the solder wave. 4. Cleaning When necessary, cleaning should occur only with isopropyl alcohol at room temperature for a duration of no more than one minute. Dry at room temperature before use. Do not clean the LEDs by the ultrasonic. When it is absolutely necessary, the influence of ultrasonic cleaning on the LEDs depends on factors such as ultrasonic power and the assembled condition. Ultrasonic cleaning shall be pre-qualified to ensure this will not cause damage to the LED 5. Circuit Protection Below the zener reference voltage Vz, all the current flows through LED and as the voltage rises to Vz, the zener diode "breakdown." If the voltage tries to rise above Vz current flows through the zener branch to keep the voltage at exactly Vz. When the LED is connected using serial circuit, if either piece of LED is no light up but current can't flow through causing others to light down. In new design, the LED is parallel with zener diode. if either piece of LED is no light up but current can flow through causing others to light up.
Everlight Electronics Co., Ltd. Device Number :
http\\:www.everlight.com Prepared date:1-15-2008
Rev:
Page: 10 of 12
Prepared by: Dante Chen
Technical Data Sheet
Preliminary
EHP-5393/UT31C-P01
6. Heat Management Heat management of LEDs must be taken into consideration during the design stage of LED application. The current should be de-rated appropriately by referring to the de-rating curve found in each product specification. The temperature surrounding the LED in the application should be controlled. Please refer to the data sheet de-rating curve. If the emitter is operated, consider using metal heat sink with the lowest possible thermal resistance. For the thermal performance using a flat heat sink, allow an exposed surface area of about 25mm2 at least. 7. ESD (Electrostatic Discharge) Electrostatic discharge (ESD) or surge current (EOS) can damage LEDs. An ESD wrist strap, ESD shoe strap or antistatic gloves must be worn whenever handling LEDs. All devices, equipment and machinery must be properly grounded.
Use ion blower to neutralize the static charge which might have built up on surface of the
LEDs plastic lens as a result of friction between LEDs during storage and handing.
Everlight Electronics Co., Ltd. Device Number :
http\\:www.everlight.com Prepared date:1-15-2008
Rev:
Page: 11 of 12
Prepared by: Dante Chen
Technical Data Sheet
8. Other
Preliminary
EHP-5393/UT31C-P01
Above specification may be changed without notice. EVERLIGHT will reserve authority on material change for above specification. When using this product, please observe the absolute maximum ratings and the instructions for using outlined in these specification sheets. EVERLIGHT assumes no responsibility for any damage resulting from use of the product which does not comply with the absolute maximum ratings and the instructions included in these specification sheets. These specification sheets include materials protected under copyright of EVERLIGHT corporation. Please don't reproduce or cause anyone to reproduce them without EVERLIGHT's consent.
Everlight Electronics Co., Ltd. CO., LTD.http\\:www.everlight.com 886-2-2267-2000, 2267-9936 12 of 12 Rev: Page: EVERLIGHT ELECTRONICS Tel: Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Fax: 886-2267-6244, 2267-6189, 2267-6306 Device Number : Prepared date:1-15-2008 Prepared by: Dante Chen Tucheng, Taipei 236, Taiwan, R.O.C http:\\www.everlight.com

▲Up To Search▲

Price & Availability of EHP-5393-UT31C-P01

	To Download EHP-5393-UT31C-P01 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .