View SDC1204-221MF_4496266.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

SMD POWER INDUCTORS
1. PART NO. EXPRESSION :
SDC1204 SERIES
SDC1204-3R9YF
(a) (b) (c) (d)(e)
(a) Series code (b) Dimension code (c) Inductance code : 3R9 = 3.9uH
(d) Tolerance code : M = 20%, Y = 30% (e) F : Lead Free
2. CONFIGURATION & DIMENSIONS :
Clip Termination A C D
L G
220
B
E
PCB Pattern Unit:m/m A 12.00.3 B 12.00.3 C 5.0 Max. D 5.00.2 E 7.60.2 G 7.0 Ref. H 5.4 Ref. L 12.6 Ref.
3. SCHEMATIC :
4. GENERAL SPECIFICATION : a) Temp. rise : 40C Max. b) Ambient temp. : 25C c) Rated current : Base on temp. rise & L/L0A = 30% Max. d) Operating temp. : -25C to +85C e) Storage temp. : -25C to +85C
NOTE : Specifications subject to change without notice. Please check our website for latest information.
H
12.05.2008
SUPERWORLD ELECTRONICS (S) PTE LTD
PG. 1
SMD POWER INDUCTORS
5. ELECTRICAL CHARACTERISTICS : Part No. SDC1204-3R9YF SDC1204-4R7YF SDC1204-6R8YF SDC1204-8R2YF SDC1204-100MF SDC1204-120MF SDC1204-150MF SDC1204-180MF SDC1204-220MF SDC1204-270MF SDC1204-330MF SDC1204-390MF SDC1204-470MF SDC1204-560MF SDC1204-680MF SDC1204-820MF SDC1204-101MF SDC1204-121MF SDC1204-151MF SDC1204-181MF SDC1204-221MF SDC1204-271MF SDC1204-331MF Inductance ( H ) 3.9 30% 4.7 30% 6.8 30% 8.2 30% 10 20% 12 20% 15 20% 18 20% 22 20% 27 20% 33 20% 39 20% 47 20% 56 20% 68 20% 82 20% 100 20% 120 20% 150 20% 180 20% 220 20% 270 20% 330 20% Test Frequency ( Hz ) 1V / 100K 1V / 100K 1V / 100K 1V / 100K 1V / 100K 1V / 100K 1V / 100K 1V / 100K 1V / 100K 1V / 100K 1V / 100K 1V / 100K 1V / 100K 1V / 100K 1V / 100K 1V / 100K 1V / 100K 1V / 100K 1V / 100K 1V / 100K 1V / 100K 1V / 100K 1V / 100K
SDC1204 SERIES
DCR () Max. 0.015 0.018 0.023 0.026 0.028 0.038 0.050 0.057 0.066 0.080 0.097 0.132 0.160 0.190 0.220 0.260 0.308 0.380 0.530 0.620 0.700 0.870 0.990
IDC (A) Max. 6.50 5.70 4.90 4.60 4.50 4.00 3.20 3.10 2.90 2.80 2.70 2.10 1.90 1.80 1.50 1.30 1.20 1.10 0.95 0.85 0.80 0.60 0.50
NOTE : Specifications subject to change without notice. Please check our website for latest information.
12.05.2008
SUPERWORLD ELECTRONICS (S) PTE LTD
PG. 2
SMD POWER INDUCTORS
6. RELIABILITY AND TEST CONDITIONS :
SDC1204 SERIES
ITEM
Electrical Characteristics Test Inductance DCR Heat Rated Current (Irms)
PERFORMANCE
Refer to standard electrical characteristics list
TEST CONDITION
HP4284A, CH11025, CH3302, CH1320, CH1320S LCR meter. CH16502, Agilent33420A Micro-Ohm Meter. Irms(A) will cause the coil temperature rise approximately T=40C without core loss 1. Applied the allowed DC current 2. Temperature measured by digital surface thermometer Isat(A) will cause Lo to drop approximately 20% max.
Saturation Current (Isat) Mechanical Performance Test Solderability Test More than 90% of the terminal electrode should be covered with solder.
Preheating Dipping 230C Natural cooling
Preheat : 150C, 60sec. Solder : Sn-Ag3.0-Cu0.5 Solder Temperature : 2305C Flux for lead free : rosin Dip Time : 41sec.
150C
60 seconds
41 seconds
Solder Heat Resistance
1. Appearance : No significant abnormality 2. Inductance change : Within 20%
Preheating 260C Dipping
Natural
cooling
Preheat : 150C, 60sec. Solder : Sn-Ag3.0-Cu0.5 Solder Temperature : 2605C Flux for lead free : rosin Dip Time : 100.5sec.
150C
60 seconds
100.5 seconds
Reliability Test High Temperature Life Test Low Temperature Life Test Thermal Shock Temperature : 855C Time : 50012 hours Measure at room temperature after placing for 2 to 3 hrs. 1. Appearance : No damage 2. Inductance : Within 20% of initial value. No disconnection or short circuit. Temperature : -255C Time : 50012 hours Measure at room temperature after placing for 2 to 3 hrs. Conditions of 1 cycle.
Step 1 2 3 4 Temperature (C) -253 Room Temperature +853 Room Temperature Times (min.) 303 Within 3 303 Within 3
Total : 5 cycles Measure at room temperature after placing for 2 to 3 hrs. Humidity Resistance 1. Appearance : No damage 2. Inductance : Within 20% of initial value. No disconnection or short circuit. Temperature : 405C Humidity : 90% to 95% Applied Current : Rated Curent Time : 50012 hours Measure at room temperature after placing for 2 to 3 hrs.
NOTE : Specifications subject to change without notice. Please check our website for latest information.
12.05.2008
SUPERWORLD ELECTRONICS (S) PTE LTD
PG. 3
SMD POWER INDUCTORS
7. SOLDERIND AND MOUNTING : 7-1. Recommended PC Board Pattern
12.6 7.0
SDC1204 SERIES
7-2. Soldering Mildly activated rosin fluxes are preferred. The minimum amount of solder can lead to damage from the stresses caused by the difference in coefficients of expansion between solder, chip and substrate. Our terminations are suitable for all wave and re-flow soldering systems. If hand soldering cannot be avoided, the preferred technique is the utilization of hot air soldering tools. 7-2.1 Solder Re-flow : Recommended temperature profiles for re-flow soldering in Figure 1. 7-2.2 Soldering Iron (Figure 2) : Products attachment with soldering iron is discouraged due to the inherent process control limitations. In the event that a soldering iron must be employed the following precautions are recommended. Note : a) Preheat circuit and products to 150C. b) 280C tip temperature (max) c) Never contact the ceramic with the iron tip d) 1.0mm tip diameter (max) e) Use a 20 watt soldering iron with tip diameter of 1.0mm f) Limit soldering time to 3 secs.
Preheating TEMPERATURE C
250~260 230 180 150 60~120s
Soldering
5.4
TEMPERATURE C
10s max.
Natural cooling
Preheating
280 260 150
Soldering
Natural cooling
30~60s
Over 1min.
Gradual Cooling Within 3secs.
Figure 1. Re-flow Soldering
Figure 2. Iron Soldering
NOTE : Specifications subject to change without notice. Please check our website for latest information.
12.05.2008
SUPERWORLD ELECTRONICS (S) PTE LTD
PG. 4
SMD POWER INDUCTORS
8. PACKAGING INFORMATION : 8-1. Tape and Reel Dimension
SDC1204 SERIES
COVER TAPE
2.00.5 D B OC A
EMBOSSED CARRIER
220
220
220
220
220
Type 13" x 24mm
A(mm) 24.00.1
B(mm) 1001
C(mm) 130.5
D(mm) 330
8-3. Packaging Quantity
Size Chip / Reel Reel Style
SDC1204 750 13" x 24mm
NOTE : Specifications subject to change without notice. Please check our website for latest information.
12.05.2008
SUPERWORLD ELECTRONICS (S) PTE LTD
PG. 5

▲Up To Search▲

Price & Availability of SDC1204-221MF

	To Download SDC1204-221MF Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .