![]() |
|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
HMC890LP5E v00.1209 FILTER - TUNABLE, BAND PASS SMT 1 - 2 GHz 3 FILTERS - TUNABLE - SMT Typical Applications The HMC890LP5E is ideal for: * Test & Measurement Equipment * Military, RADAR & EW * SATCOM & Space * R&D Laboratories Features Fast Tuning Response Excellent Wideband Rejection Single Chip Replacement for Mechanically Tuned Designs 32 Lead 5x5 mm SMT Package: 25 mm2 Functional Diagram General Description The HMC890LP5E is a MMIC band pass filter which features a user selectable passband frequency. The 3 dB filter bandwidth is approximately 11%. The 20 dB filter bandwidth is approximately 33%. The center frequency can be varied between 1 and 2 GHz by applying an analog tune voltage between 0 and 14V. This tunable filter can be used as a much smaller alternative to physically large switched filter banks and cavity tuned filters. The HMC890LP5E has excellent microphonics due to the monolithic design, and provides a dynamically adjustable solution in advanced communications applications. Electrical Specifi cations, TA = +25C, Vfctl = Vbwctl Unless Otherwise Stated Parameter Fcenter Tuning Range 3 dB Bandwidth Low Side Rejection Frequency (Rejection >20 dB) High Side Rejection Frequency (Rejection >20 dB) Re-entry Frequency (Rejection <30 dB) 3 dB Bandwidth Control (Vbwctl) Insertion Loss Return Loss Maximum Input Power for Linear Operation Frequency Control Voltage (Vfctl) Source/Sink Current (Ifctl) Bandwidth Control Voltage (Vbwctl) Source/Sink Current (Ibwctl) Residual Phase Noise [1] (1 MHz Offset) Fcenter Drift Rate Tuning Characteristics [2] tFULLBAND (0% Vfctl to 90% RF) -155 -0.3 200 0 0 Min. 1 11 0.86*Fcenter 1.19*Fcenter 9 3 9 10 10 14 1 14 1 Typ. Max. 2 Units GHz % GHz GHz GHz % dB dB dBm V mA V mA dBc/Hz MHz/C ns [1] Optimum residual phase noise performance requires the use of a low noise driver circuit. [2] Tuning speed is dependent on driver circuit. Data measured with a high speed op-amp driver and includes driver slew rate delay. 3 - 14 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC890LP5E v00.1209 FILTER - TUNABLE, BAND PASS SMT 1 - 2 GHz Broadband Insertion Loss vs. Control Voltages, Vfctl = Vbwctl 0 -10 Broadband Return Loss vs. Control Voltages, Vfctl = Vbwctl 0 -5 3 S11 S22 14V 14V -10 -15 -20 -30 -40 -50 -60 -70 0 5 10 15 20 25 30 0V -20 -25 -30 -35 -40 0 5 10 15 20 7V 25 30 FREQUENCY (GHz) FREQUENCY (GHz) Insertion Loss vs. Control Voltages, Vfctl = Vbwctl 0 -2 Return Loss vs. Control Voltages, Vfctl = Vbwctl 0 -5 INSERTION LOSS (dB) RETURN LOSS (dB) -4 -6 -8 -10 0V -10 7V 14V 7V -15 -20 -25 -30 -35 S11 S22 14V 0V -12 -14 -16 -18 0 0.5 1 1.5 2 2.5 3 0 0.5 1 1.5 2 2.5 3 FREQUENCY (GHz) FREQUENCY (GHz) Insertion Loss vs. Temperature, Vfctl = Vbwctl = 7V 0 -2 +25C +85C -40C Return Loss vs. Temperature, Vfctl = Vbwctl = 7V 0 -5 INSERTION LOSS (dB) -6 -8 -10 -12 -14 -16 -18 0 0.5 1 1.5 RETURN LOSS (dB) -4 -10 -15 -20 -25 -30 -35 -40 -45 S11 S22 7V +25C +85C -40C 2 2.5 3 0 0.5 1 1.5 2 2.5 3 FREQUENCY (GHz) FREQUENCY (GHz) For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 3 - 15 FILTERS - TUNABLE - SMT 0V 7V INSERTION LOSS (dB) RETURN LOSS (dB) HMC890LP5E v00.1209 FILTER - TUNABLE, BAND PASS SMT 1 - 2 GHz 3 FILTERS - TUNABLE - SMT Broadband Insertion Loss vs. Vbwctl, Vfctl = 7V 0 -10 Broadband Return Loss vs. Vbwctl, Vfctl = 7V 0 -5 Vbwctl=4V RETURN LOSS (dB) Vbwctl=7V Vbwctl=10V Vbwctl=4V INSERTION LOSS (dB) -20 -30 -40 -50 -60 -70 -80 0 -10 -15 Vbwctl=10V -20 -25 -30 -35 S11 S22 Vbwctl=7V 5 10 15 20 25 30 0 5 10 15 20 25 30 FREQUENCY (GHz) FREQUENCY (GHz) Insertion Loss vs. Vbwctl, Vfctl = 7V 0 -2 Return Loss vs. Vbwctl, Vfctl = 7V 0 -5 INSERTION LOSS (dB) RETURN LOSS (dB) -4 -6 -8 Vbwctl=4V -10 Vbwctl=10V -15 S11 S22 Vbwctl=4V Vbwctl=7V -20 -10 Vbwctl=7V -25 Vbwctl=10V -12 -14 -16 0 0.5 1 1.5 2 2.5 3 -30 -35 0 0.5 1 1.5 2 2.5 3 3.5 4 FREQUENCY (GHz) FREQUENCY (GHz) Center Frequency vs. Temperature, Vfctl = Vbwctl 4 Insertion Loss vs. Temperature, Vfctl = Vbwctl 0 +25C +85C -40C CENTER FREQUENCY (GHz) 3 INSERTION LOSS (dB) 8 10 12 14 +25C +85C -40C -4 -8 2 -12 1 -16 0 0 2 4 6 -20 0 2 4 6 8 10 12 14 Vfctl (V) Vfctl (V) 3 - 16 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC890LP5E v00.1209 FILTER - TUNABLE, BAND PASS SMT 1 - 2 GHz 3 dB Bandwidth vs. Temperature, Vfctl = Vbwctl 20 +25C +85C -40C Maximum Return Loss in a 2 dB Bandwidth vs. Temperature, Vfctl = Vbwctl 0 -2 3 FILTERS - TUNABLE - SMT 3 - 17 16 -4 RETURN LOSS (dB) BANDWIDTH (%) -6 -8 -10 -12 -14 -16 -18 +25C +85C -40C 12 8 4 0 0 2 4 6 8 10 12 14 -20 0 2 4 6 8 10 12 14 Vfctl (V) Vfctl (V) Low Side Rejection Ratio vs. Temperature, Vfctl = Vbwctl [1] 1 High Side Rejection Ratio vs. Temperature, Vfctl = Vbwctl [1] 1.5 +25C +85C -40C F20dB TO Fcenter RATIO 0.9 F20dB To Fcenter RATIO 10 12 14 1.4 0.8 +25C +85C -40C 1.3 0.7 1.2 0.6 1.1 0.5 0 2 4 6 8 1 0 2 4 6 8 10 12 14 Vfctl (V) Vfctl (V) Tuning Sensitivity vs. Temperature, Vfctl = Vbwctl 160 140 Group Delay 8 7 GROUP DELAY (ns) 6 5 7V 4 3 2 1 14V 0V SENSITIVITY (MHz/V) 120 100 80 60 40 20 0 0 2 4 6 8 10 12 14 +25C +85C -40C 0 0.5 1 Vfctl (V) 1.5 FREQUENCY (GHz) 2 2.5 [1] Rejection ratio is defined as the ratio of the frequency at which the relative insertion loss is 20 dB to center For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC890LP5E v00.1209 FILTER - TUNABLE, BAND PASS SMT 1 - 2 GHz 3 FILTERS - TUNABLE - SMT 3 dB Bandwidth vs. Bandwidth Control 20 Insertion Loss vs. Bandwidth Control 0 Vbwctl=Vfctl-3V INSERTION LOSS (dB) 16 -5 Vbwctl=Vfctl-3V Vfctl=Vbwctl BANDWIDTH (%) Vfctl=Vbwctl 12 -10 8 -15 4 Vbwctl=Vfctl+3V Vbwctl=Vfctl+3V -20 0 0 2 4 6 8 10 12 14 -25 0 2 4 6 8 10 12 14 Vfctl (V) Vfctl (V) Low Side Rejection Ratio vs. Bandwidth Control [1] 1 High Side Rejection Ratio vs. Bandwidth Control [1] 1.5 Vbwctl=Vfctl+3V F20dB TO Fcenter RATIO 0.9 F20dB TO Fcenter RATIO 1.4 0.8 1.3 Vbwctl=Vfctl-3V Vfctl=Vbwctl Vfctl=Vbwctl 0.7 Vbwctl=Vfctl-3V 1.2 0.6 1.1 Vbwctl=Vfctl+3V 0.5 0 2 4 6 8 10 12 14 1 0 2 4 6 8 10 12 14 Vfctl (V) Vfctl (V) Maximum Return Loss in a 2 dB Bandwidth vs. Bandwidth Control 0 -5 Vfctl=Vbwctl Vbwctl=Vfctl-3V RETURN LOSS (dB) -10 -15 Vbwctl=Vfctl+3V -20 -25 0 2 4 6 8 10 12 14 Vfctl (V) [1] Rejection ratio is defined as the ratio of the frequency at which the relative insertion loss is 20 dB to center 3 - 18 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC890LP5E v00.1209 FILTER - TUNABLE, BAND PASS SMT 1 - 2 GHz Absolute Maximum Ratings Frequency Control Voltage (Vfctl) Bandwidth Control Voltage (Vbwctl) RF Power Input Storage Temperature ESD Rating (HBM) -0.5 to +15V -0.5 to +15V 27 dBm -65 to +150 C Class 1B Reliability Information Junction Temperature to Maintain 1 Million Hour MTTF Nominal Junction Temperature (T= 85 C and Pin = 10 dBm) Operating Temperature 150 C 90 C -40 to +85 C 3 FILTERS - TUNABLE - SMT 3 - 19 ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS Outline Drawing NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS] 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE. 4. Pin BURR LENGTH SHALL BE 0.15mm MAXIMUM. Pin BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED LAND PATTERN. Package Information Part Number HMC890LP5E Package Body Material RoHS-compliant Low Stress Injection Molded Plastic Lead Finish 100% matte Sn MSL Rating MSL1 [2] Package Marking [1] H890 XXXX [1] 4-Digit lot number XXXX [2] Max peak reflow temperature of 260 C For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC890LP5E v00.1209 FILTER - TUNABLE, BAND PASS SMT 1 - 2 GHz 3 FILTERS - TUNABLE - SMT Pin Descriptions Pin Number 1 - 4, 7 - 11, 13 15 - 18, 21 - 32 Function N/C Description The pins are not connected internally; however, all data shown herein was measured with these pins connected to RF/DC ground externally. These pins and exposed paddle must be connected to RF/DC ground. Interface Schematic 5, 20 GND 6 RFIN This pin is DC coupled and matched to 50 Ohms. External voltage must not be applied to this pin. 12 Vfctl Center frequency control voltage. 14 Vbwctl Bandwidth control voltage. 19 RFOUT This pin is DC coupled and matched to 50 Ohms. External voltage must not be applied to this pin. Application Circuit 3 - 20 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC890LP5E v00.1209 FILTER - TUNABLE, BAND PASS SMT 1 - 2 GHz Evaluation PCB 3 FILTERS - TUNABLE - SMT List of Materials for Evaluation PCB 128531 [1] Item J1 - J4 C1, C2 U1 PCB [2] Description SMA - SRI 100 pF Capacitor, 0402 Pkg. HMC890LP5E Filter 127338 Evaluation PCB [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Arlon 25FR or Rogers 25FR The circuit board used in the application should use RF circuit design techniques. Signal lines should have 50 Ohms impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 3 - 21 |
Price & Availability of HMC890LP5E
![]() |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |