View CXM3519ER_4669068.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

SP9T/10T Antenna Switch Module for GSM and UMTS/CDMA Dual Mode Handset
CXM3519ER
Description
The CXM3519ER is a SP9T/SP10T antenna switch module for GSM and UMTS/CDMA dual-mode handset. This IC has a built-in dual low pass filter and a +1.8V CMOS compatible decoder. The Sony GaAs junction gate pHEMT (JPHEMT) MMIC process is used for low insertion loss and high linearity. The device has low BOM and small mount Area with no DC blocking capacitor.
Features
Low insertion loss (SP10T): 0.85dB (Typ.) Tx1 (GSM Low Band Tx) 0.88dB (Typ.) Tx2 (GSM High Band Tx) 0.50dB (Typ.) TRx1 (UMTS Band I) Low insertion loss (SP9T): 0.85dB (Typ.) Tx1 (GSM Low Band Tx) 0.85dB (Typ.) Tx2 (GSM High Band Tx) 0.47dB (Typ.) TRx1 (UMTS Band I) High attenuation: 35dB (Typ.) On Tx1 path @1648 - 1830MHz 33dB (Typ.) On Tx2 path @3420 - 3820MHz Low voltage operation: VDD = +2.5V No DC blocking capacitors Small package: VQFN-26P (3.0mm x 3.8mm x 0.8mm Typ.) Lead-Free and RoHS compliant
Structure
GaAs Junction-gate PHEMT MMIC Switch, CMOS Decoder and Dual-LPF.
Note on Handling - GaAs MMIC's are ESD sensitive devices. Special handling precautions are required.
Sony reserves the right to change products and specifications without prior notice. This information does not convey any license by any implication or otherwise under any patents or other right. Application circuits shown, if any, are typical examples illustrating the operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits.
-1-
E07Y05C86
CXM3519ER
Block Diagram (SP9T/SP10T)
TRx1 TRx2 TRx3 Ant
LPF1
TRx4/GND Tx1
Decoder Logic
LPF2
Tx2 Rx1 Rx2 Rx3 Rx4
Pin Configuration
GND GND GND 9 8 7 6 VQFN-26P PKG (3.0mm x 3.8mm x 0.8mm Typ.) Top View 5 4 3 2 1 22 VDD 23 CTLD 24 CTLC 25 CTLB 26 CTLA GND Ant GND TRx4/GND TRx3 GND TRx2 GND
13 GND GND Rx4 Rx3 Rx2 Rx1 TRx1 GND 14 15 16 17 18 19 20 21
Tx1
12
11
10
Pin 5 SP9T : Connect to GND directly SP10T : TRx4
-2-
Tx2
CXM3519ER
Pin Description
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 GND TRx2 GND TRx3 TRx4/GND GND Ant GND GND Tx2 (DCS/PCS) GND GND Tx1 (GSM850/900M) Symbol Pin No. 14 15 16 17 18 19 20 21 22 23 24 25 26 GND GND Rx4 Rx3 Rx2 Rx1 TRx1 GND VDD CTLD CTLC CTLB CTLA Symbol
-3-
CXM3519ER
RF Switch (SP9T/SP10T)
Ant
F1 F8
F2 F9 F3
F14
F7
F16
F18
F20
F4 F11
F5 F12 F13
F6 F15 F17 F19 F21
LPF1
LPF2
F10
Tx1
Tx2
Rx1
Rx2
Rx3
Rx4
TRx1
TRx2
TRx3
TRx4/GND
Truth Table
Active path Tx1 Tx2 Rx1*1 Rx2*1 Rx3*1 Rx4*1 TRx1 TRx2 TRx3 TRx4 Vctl state A H H L L L L H H H H B H L L L H H L H L H C L L L H H L H H H H D L L L L L L L L H H F1 H L L L L L L L L L F2 L H L L L L L L L L F3 L L H L L L L L L L F4 L L L H L L L L L L F5 L L L L H L L L L L F6 L L L L L H L L L L F7 L L L L L L H L L L F8 L H H H H H H H H H Switch state*2 F9 F10 F11 F12 F13 F14 F15 F16 F17 F18 F19 F20 F21 H L H H H H H H H H H H L H H H H H H H H H H L H H H H H H H H H H L H H H H H H H H H H L H H H H L L H H H H L L L L H H H H H H L H H H L L L L L L L H L L H H H H H H H L H H L L L L L L L L H L H H H H H H H H L H L L L L L L L L L H H H H H H H H H H L
State 1 2 3 4 5 6 7 8 9 10
*1
*2
Each Rx path can be used from 869MHz to 1990MHz frequency, user can select these Rx paths changeably. State "L" means a switch "OFF", state "H" means a switch "ON".
-4-
CXM3519ER
Electrical Characteristics
Supply Voltage
(Ta = 25C) Item Bias voltage (VDD) Min. 2.5 Typ. 2.65 Max. 3.3 Unit V
Logic Value
(Ta = 25C) Item Control voltage (CTL-A/B/C/D) State High Low Min. 1.5 0 Typ. 1.80 -- Max. 3.3 0.3 Unit V
Absolute Maximum Ratings
Item Bias voltage (VDD) Control voltage (CTL-A/B/C/D) Maximum input power (Tx1) Maximum input power (Tx2) Maximum input power (TRx1, 2, 3, 4) Maximum input power (Rx1, 2, 3, 4) Operating temperature Storage temperature Ratings 4V (Ta: +25C) 4V (Ta: +25C) +36dBm (Duty cycle = 12.5%) (Ta: +25C) +34dBm (Duty cycle = 12.5%) (Ta: +25C) +32dBm (Ta: +25C) +13dBm (Ta: +25C) -20 to +90C -65 to +150C
-5-
CXM3519ER
Recommended Circuit 1 (SP9T) Ex.) GSM (4 bands) / UMTS (3 bands)
GND
GND
13 GND GND Rx4 Rx3 Rx2 Rx1 TRx1 GND
12
11
10
9 GND ANT GND GND TRx3 GND TRx2 GND L1 C1
GND 8 7 6 5 4 3 2 1 26 CTLA
14 15 16 17 18 19 20 21 VQFN-26P PKG (3.0mm x 3.8mm x 0.8mm Typ.) Top View
22 VDD
Tx1
23 CTLD
24 CTLC
25 CTLB
C2
Note) 1. No DC blocking capacitors are required on all RF ports. 2. The DC levels of all RF ports are GND. 3. L1 inductor (22nH) and C1 capacitor (22pF) are recommended on Ant port for ESD protection. 4. C2 capacitor (100pF) is recommended. 5. Connect Pin 5 to GND directly.
-6-
Tx2
CXM3519ER
Electrical Characteristics (Recommended Circuit 1 (SP9T))
(VDD = 2.65V, Vctl = 1.80V, Ta = 25C)
Item Symbol Ant-Tx1 Ant-Tx2 Ant-TRx1 (Tx) Ant-TRx1 (Rx) Ant-TRx2 (Tx) Ant-TRx2 (Rx) Ant-TRx3 (Tx) Insertion loss I.L Ant-TRx3 (Rx) Ant-Rx1 Ant-Rx2 Ant-Rx3 Ant-Rx4 Path
*1 *2 *3 *4 *5 *6 *5 *6 *7 *8 *7 *8 *7 *8 *7 *8
Conditions
Min. -- -- -- -- -- -- -- -- -- -- -- --
Typ. 0.85 0.85 0.47 0.48 0.51 0.57 0.48 0.56 0.66 1.02 0.65 1.01 0.65 0.98 0.65 0.94
Max. 1.00 1.05 0.62 0.63 0.61 0.72 0.58 0.71 0.76 1.17 0.75 1.16 0.75 1.13 0.75 1.09
Unit
dB
Electrical characteristics are measured with all RF ports terminated in 50 and recommended circuit 1 (SP9T).
*1 *2 *3 *4 *5 *6 *7 *8
Frequency = 824 to 915MHz, Frequency = 1710 to 1910MHz, Frequency = 1920 to 1980MHz, Frequency = 2110 to 2170MHz, Frequency = 824 to 894MHz, Frequency = 1710 to 1990MHz, Frequency = 869 to 960MHz, Frequency = 1805 to 1990MHz,
Item Symbol Tx1-Rx1 Tx1-Rx2 Tx1-Rx3 Tx1-Rx4 Tx1-TRx1 Tx1-TRx2 Tx1-TRx3 Tx1-Tx2 Path
Pin on Tx1: +34dBm C.W. Pin on Tx2: +32dBm C.W. Pin on TRx1: +26dBm C.W. Pin on TRx1: +26dBm C.W. Pin on TRx2 or 3: +26dBm C.W. Pin on TRx2 or 3: +26dBm C.W. Pin on Ant: +10dBm C.W. Pin on Ant: +10dBm C.W.
Conditions Min. 35 35 35 824 to 915MHz 35 35 45 45 20 1648 to 1830MHz 20 25 32 32 32 1710 to 1910MHz 32 30 40 40 20 Typ. 42 42 42 42 39 54 57 23 22 28 37 37 37 38 33 49 44 26 Max. -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- dB Unit
Active path: Tx1-Ant (State1)
Isolation
ISO.
Tx2-Ant Tx2-Rx1 Tx2-Rx2 Tx2-Rx3 Tx2-Rx4 Tx2-TRx1 Tx2-TRx2 Tx2-TRx3 Tx2-Tx1
Active path: Tx2-Ant (State2)
-7-
CXM3519ER
Electrical Characteristics (Recommended Circuit 1 (SP9T))
(VDD = 2.65V, Vctl = 1.80V, Ta = 25C)
Item Symbol Path Active path: TRx1-Ant (State7) TRx1-Rx1 TRx1-Rx2 TRx1-Rx3 TRx1-Rx4 TRx1-Tx1 TRx1-Tx2 TRx1-TRx2 TRx1-TRx3 Active path: TRx2-Ant (State8) TRx2-Rx1 TRx2-Rx2 TRx2-Rx3 TRx2-Rx4 TRx2-Tx1 TRx2-Tx2 TRx2-TRx1 TRx2-TRx3 TRx2-Rx1 TRx2-Rx2 TRx2-Rx3 Isolation ISO. TRx2-Rx4 TRx2-Tx1 TRx2-Tx2 TRx2-TRx1 TRx2-TRx3 Active path: TRx3-Ant (State9) TRx3-Rx1 TRx3-Rx2 TRx3-Rx3 TRx3-Rx4 TRx3-Tx1 TRx3-Tx2 TRx3-TRx1 TRx3-TRx2 TRx3-Rx1 TRx3-Rx2 TRx3-Rx3 TRx3-Rx4 TRx3-Tx1 TRx3-Tx2 TRx3-TRx1 TRx3-TRx2 1710 to 1910MHz 824 to 849MHz 35 35 35 40 35 40 30 30 25 25 30 30 45 25 25 25 41 42 43 46 40 43 37 37 33 33 35 38 52 33 30 30 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 1710 to 1910MHz 824 to 849MHz 35 35 35 40 35 35 30 30 25 25 30 30 45 25 25 25 40 41 43 45 40 42 37 36 32 33 35 38 56 32 29 31 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- dB 1920 to 1980MHz 17 20 30 35 35 25 40 35 19 27 34 41 42 30 45 42 -- -- -- -- -- -- -- -- Conditions Min. Typ. Max. Unit
-8-
CXM3519ER
Electrical Characteristics (Recommended Circuit 1 (SP9T))
(VDD = 2.65V, Vctl = 1.80V, Ta = 25C)
Item Symbol Path TRx: 835MHz State7 TRx1-Ant TRx: 1880MHz State7 TRx: 1950MHz State7 TRx: 835MHz State8 IMD2 TRx2-Ant TRx: 1880MHz State8 TRx: 1950MHz State8 TRx: 835MHz State9 TRx3-Ant TRx: 1880MHz State9 TRx: 1950MHz State9 TRx: 835MHz State7 TRx1-Ant TRx: 1880MHz State7 TRx: 1950MHz State7 TRx: 835MHz State8 IMD3 TRx2-Ant TRx: 1880MHz State8 TRx: 1950MHz State8 TRx: 835MHz State9 TRx3-Ant TRx: 1880MHz State9 TRx: 1950MHz State9 Conditions Ant: 45MHz *1 Ant: 1715MHz *2 Ant: 80MHz *3 Ant: 3840MHz *4 Ant: 190MHz *5 Ant: 4090MHz *6 Ant: 45MHz *1 Ant: 1715MHz *2 Ant: 80MHz *3 Ant: 3840MHz *4 Ant: 190MHz *5 Ant: 4090MHz *6 Ant: 45MHz *1 Ant: 1715MHz *2 Ant: 80MHz *3 Ant: 3840MHz *4 Ant: 190MHz *5 Ant: 4090MHz *6 Ant: 790MHz *7 Ant: 2550MHz *8 Ant: 1800MHz *9 Ant: 5720MHz *10 Ant: 1760MHz *11 Ant: 6040MHz *12 Ant: 790MHz *7 Ant: 2550MHz *8 Ant: 1800MHz *9 Ant: 5720MHz *10 Ant: 1760MHz *11 Ant: 6040MHz *12 Ant: 790MHz *7 Ant: 2550MHz *8 Ant: 1800MHz *9 Ant: 5720MHz *10 Ant: 1760MHz *11 Ant: 6040MHz *12 Min. -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- Typ. -119 -118 -108 -110 -108 -117 -119 -117 -107 -107 -109 -116 -118 -117 -106 -110 -107 -118 -108 -110 -107 -112 -107 -115 -106 -110 -105 -110 -105 -112 -108 -110 -105 -106 -105 -110 Max. -105 -105 -103 -105 -103 -105 -105 -105 -102 -102 -104 -105 -105 -105 -101 -105 -102 -105 -103 -105 -102 -105 -102 -105 -101 -105 -100 -105 -100 -105 -103 -105 -100 -101 -100 -105 dBm Unit
Intermodulation distortion level in Rx band
Electrical characteristics are measured with all RF ports terminated in 50 and recommended circuit 1 (SP9T).
*1 *2 *3 *4 *5 *6 *7 *8 *9 *10 *11 *12
TRx port: +20dBm, 835MHz, TRx port: +20dBm, 835MHz, TRx port: +20dBm, 1880MHz, TRx port: +20dBm, 1880MHz, TRx port: +20dBm, 1950MHz, TRx port: +20dBm, 1950MHz, TRx port: +20dBm, 835MHz, TRx port: +20dBm, 835MHz, TRx port: +20dBm, 1880MHz, TRx port: +20dBm, 1880MHz, TRx port: +20dBm, 1950MHz, TRx port: +20dBm, 1950MHz,
Ant port: -15dBm, 45MHz Ant port: -15dBm, 1715MHz Ant port: -15dBm, 80MHz Ant port: -15dBm, 3840MHz Ant port: -15dBm, 190MHz Ant port: -15dBm, 4090MHz Ant port: -15dBm, 790MHz Ant port: -15dBm, 2550MHz Ant port: -15dBm, 1800MHz Ant port: -15dBm, 5720MHz Ant port: -15dBm, 1760MHz Ant port: -15dBm, 6040MHz
-9-
CXM3519ER
Electrical Characteristics (Recommended Circuit 1 (SP9T))
(VDD = 2.65V, Vctl = 1.80V, Ta = 25C)
Item Symbol Path 2nd harmonic 3rd harmonic 2nd harmonic 3rd harmonic 2nd harmonic 3rd harmonic 2nd harmonic 3rd harmonic 2nd harmonic 3rd harmonic Conditions 1648 to 1698MHz 1780 to 1830MHz 2472 to 2547MHz 2670 to 2745MHz 3420 to 3570MHz 3700 to 3820MHz 5130 to 5355MHz 5550 to 5730MHz 3840 to 3960MHz 5760 to 5940MHz 3840 to 3960MHz 5760 to 5940MHz 3840 to 3960MHz 5760 to 5940MHz C.W. Pin = +34dBm Min. -- -- -- -- -- -- -- -- -- -- Typ. -49 -44 -53 -45 -65 -63 -63 -61 -65 -58 Max. -36 -36 -36 -36 -36 dBm -36 -36 -36 -36 -36 Unit
Tx1-Ant *1
Tx2-Ant *2
C.W. Pin = +32dBm
Harmonics
Harm
TRx1-Ant *3
C.W. Pin = +26dBm
TRx2-Ant *3
C.W. Pin = +26dBm
TRx3-Ant *3
C.W. Pin = +26dBm
Electrical characteristics are measured with all RF ports terminated in 50 and recommended circuit 1 (SP9T).
*1 *2 *3
Frequency = 824 to 915MHz, Pin on Tx1: +34dBm C.W. Frequency = 1710 to 1910MHz, Pin on Tx2: +32dBm C.W. Frequency = 1920 to 1980MHz, Pin on TRx1 or TRx2 or TRx3: +26dBm C.W.
Item Symbol Path Conditions 1648 to 1830MHz Tx1-Ant 2472 to 2745MHz 3296 to 3660MHz Tx2-Ant 3420 to 3820MHz 5130 to 5730MHz 2fo 3fo 4fo 2fo 3fo Min. 25 25 20 25 25 Typ. 35 35 24 33 32 Max. -- -- -- -- -- dB Unit
Attenuation
ATT
Item Switching time Control current Supply current V.S.W.R.
Symbol Ts Ictl IDD V.S.W.R.
Path
Conditions 90% OFF to 90% ON
Min.
Typ. 2 --
Max. 5 10 0.4
Unit s A mA --
Active mode All ports in active paths 824 to 2170MHz
0.22 1.2
- 10 -
CXM3519ER
Recommended Circuit 2 (SP10T) Ex.) GSM (4 bands) / UMTS (4 bands)
GND
GND
13 GND GND Rx4 Rx3 Rx2 Rx1 TRx1 GND
12
11
10
9 GND ANT GND L1 C1
GND 8 7 6
14 15 16 17 18 19 20 21 VQFN-26P PKG (3.0mm x 3.8mm x 0.8mm Typ.) Top View
Tx1
Tx2
5 4 3 2 1
TRx4 TRx3 GND TRx2 GND
22 VDD
23 CTLD
24 CTLC
25 CTLB
26 CTLA
C2
Note) 1. No DC blocking capacitors are required on all RF ports. 2. DC levels of all RF ports are GND. 3. L1 inductor (22nH) and C1 capacitor (22pF) are recommended on Ant port for ESD protection. 4. C2 capacitor (100pF) is recommended.
- 11 -
CXM3519ER
Electrical Characteristics (Recommended Circuit 2 (SP10T))
(VDD = 2.65V, Vctl = 1.80V, Ta = 25C)
Item Symbol Ant-Tx1 Ant-Tx2 Ant-TRx1 (Tx) Ant-TRx1 (Rx) Ant-TRx2 (Tx) Ant-TRx2 (Rx) Ant-TRx3 (Tx) Ant-TRx3 (Rx) Insertion loss I.L Ant-TRx4 (Tx) Ant-TRx4 (Rx) Ant-Rx1 Ant-Rx2 Ant-Rx3 Ant-Rx4 Path
*1 *2 *3 *4 *5 *6 *5 *6 *7 *8
*9 *10 *9 *10 *9 *10 *9 *10
Conditions
Min. -- -- -- -- -- -- -- -- -- -- -- -- -- --
Typ. 0.85 0.88 0.50 0.52 0.53 0.59 0.49 0.61 0.40 0.40 0.67 1.04 0.64 1.03 0.65 0.98 0.65 0.95
Max. 1.00 1.08 0.65 0.67 0.63 0.74 0.59 0.76 0.50 0.50 0.77 1.19 0.74 1.18 0.75 1.13 0.75 1.10
Unit
dB
Electrical characteristics are measured with all RF ports terminated in 50 and recommended circuit 2 (SP10T).
*1 *2 *3 *4 *5 *6 *7 *8 *9 *10
Frequency = 824 to 915MHz, Frequency = 1710 to 1910MHz, Frequency = 1920 to 1980MHz, Frequency = 2110 to 2170MHz, Frequency = 824 to 894MHz, Frequency = 1710 to 1990MHz, Frequency = 824 to 849MHz, Frequency = 869 to 894MHz, Frequency = 869 to 960MHz, Frequency = 1805 to 1990MHz,
Item Symbol Tx1-Rx1 Tx1-Rx2 Tx1-Rx3 Tx1-Rx4 Tx1-TRx1 Tx1-TRx2 Tx1-TRx3 Tx1-TRx4 Tx1-Tx2 Path
Pin on Tx1: +34dBm C.W. Pin on Tx2: +32dBm C.W. Pin on TRx1: +26dBm C.W. Pin on TRx1: +26dBm C.W. Pin on TRx2 or 3: +26dBm C.W. Pin on TRx2 or 3: +26dBm C.W. Pin on TRx4: +26dBm C.W. Pin on TRx4: +26dBm C.W. Pin on Ant: +10dBm C.W. Pin on Ant: +10dBm C.W.
Conditions Min. 35 35 35 35 824 to 915MHz 35 45 45 30 20 1648 to 1830MHz 20 25 32 32 32 32 1710 to 1910MHz 30 40 40 20 20 Typ. 42 42 42 42 39 54 57 36 23 23 28 37 37 37 38 33 49 44 26 26 Max. -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- dB Unit
Active path: Tx1-Ant (State1)
Isolation
ISO.
Tx2-Ant Tx2-Rx1 Tx2-Rx2 Tx2-Rx3 Tx2-Rx4 Tx2-TRx1 Tx2-TRx2 Tx2-TRx3 Tx2-TRx4 Tx2-Tx1
Active path: Tx2-Ant (State2)
- 12 -
CXM3519ER
Electrical Characteristics (Recommended Circuit 2 (SP10T))
(VDD = 2.65V, Vctl = 1.80V, Ta = 25C)
Item Symbol Path Conditions Active path: TRx1-Ant (State7) TRx1-Rx1 TRx1-Rx2 TRx1-Rx3 TRx1-Rx4 TRx1-Tx1 1920 to 1980MHz TRx1-Tx2 TRx1-TRx2 TRx1-TRx3 TRx1-TRx4 Active path: TRx2-Ant (State8) TRx2-Rx1 TRx2-Rx2 TRx2-Rx3 TRx2-Rx4 TRx2-Tx1 824 to 849MHz TRx2-Tx2 TRx2-TRx1 TRx2-TRx3 TRx2-TRx4 TRx2-Rx1 TRx2-Rx2 TRx2-Rx3 TRx2-Rx4 TRx2-Tx1 1710 to 1910MHz TRx2-Tx2 TRx2-TRx1 TRx2-TRx3 TRx2-TRx4 Active path: TRx3-Ant (State9) TRx3-Rx1 TRx3-Rx2 TRx3-Rx3 TRx3-Rx4 824 to 849MHz TRx3-Tx1 TRx3-Tx2 TRx3-TRx1 TRx3-TRx2 TRx3-TRx4 TRx3-Rx1 TRx3-Rx2 TRx3-Rx3 TRx3-Rx4 1710 to 1910MHz TRx3-Tx1 TRx3-Tx2 TRx3-TRx1 TRx3-TRx2 TRx3-TRx4 Active path: TRx4-Ant (State10) TRx4-Rx1 TRx4-Rx2 TRx4-Rx3 TRx4-Rx4 TRx4-Tx1 824 to 849MHz TRx4-Tx2 TRx4-TRx1 TRx4-TRx2 TRx4-TRx3 Min. 17 20 30 35 35 25 40 35 20 35 35 35 40 35 35 30 30 30 25 25 30 30 45 25 25 25 20 35 35 35 40 35 40 30 30 30 25 25 30 30 45 25 25 25 17 35 35 35 40 35 40 30 40 30 Typ. 19 27 34 41 42 30 45 42 25 41 41 43 45 40 42 37 36 36 32 33 35 38 56 32 29 31 25 41 42 43 46 40 44 37 37 34 33 33 35 38 52 34 30 30 21 41 42 43 46 40 44 37 47 34 Max. -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- Unit
ISO.
dB
Isolation
ISO.
dB
- 13 -
CXM3519ER
Electrical Characteristics (Recommended Circuit 2 (SP10T))
(VDD = 2.65V, Vctl = 1.80V, Ta = 25C)
Item Symbol Path TRx: 835MHz State7 TRx: 1880MHz State7 TRx: 1950MHz State7 TRx: 835MHz State8 TRx: 1880MHz State8 TRx: 1950MHz State8 TRx: 835MHz State9 TRx: 1880MHz State9 TRx: 1950MHz State9 TRx: 835MHz State10 TRx: 1880MHz State10 TRx: 1950MHz State10 TRx: 835MHz State7 TRx: 1880MHz State7 TRx: 1950MHz State7 TRx: 835MHz State8 TRx: 1880MHz State8 TRx: 1950MHz State8 TRx: 835MHz State9 TRx: 1880MHz State9 TRx: 1950MHz State9 TRx: 835MHz State10 TRx: 1880MHz State10 TRx: 1950MHz State10 Conditions Ant: 45MHz *1 Ant: 1715MHz *2 Ant: 80MHz *3 Ant: 3840MHz *4 Ant: 190MHz *5 Ant: 4090MHz *6 Ant: 45MHz *1 Ant: 1715MHz *2 Ant: 80MHz *3 Ant: 3840MHz *4 Ant: 190MHz *5 Ant: 4090MHz *6 Ant: 45MHz *1 Ant: 1715MHz *2 Ant: 80MHz *3 Ant: 3840MHz *4 Ant: 190MHz *5 Ant: 4090MHz *6 Ant: 45MHz *1 Ant: 1715MHz *2 Ant: 80MHz *3 Ant: 3840MHz *4 Ant: 190MHz *5 Ant: 4090MHz *6 Ant: 790MHz *7 Ant: 2550MHz *8 Ant: 1800MHz *9 Ant: 5720MHz *10 Ant: 1760MHz *11 Ant: 6040MHz *12 Ant: 790MHz *7 Ant: 2550MHz *8 Ant: 1800MHz *9 Ant: 5720MHz *10 Ant: 1760MHz *11 Ant: 6040MHz *12 Ant: 790MHz *7 Ant: 2550MHz *8 Ant: 1800MHz *9 Ant: 5720MHz *10 Ant: 1760MHz *11 Ant: 6040MHz *12 Ant: 790MHz *7 Ant: 2550MHz *8 Ant: 1800MHz *9 Ant: 5720MHz *10 Ant: 1760MHz *11 Ant: 6040MHz *12 Min. -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- Typ. -119 -118 -108 -110 -108 -117 -119 -117 -107 -107 -109 -116 -118 -117 -106 -110 -107 -118 -117 -116 -105 -110 -106 -118 -108 -110 -107 -112 -107 -115 -106 -110 -105 -110 -105 -112 -108 -110 -105 -106 -105 -110 -108 -110 -105 -105 -105 -110 Max. -105 -105 -103 -105 -103 -105 -105 -105 -102 -102 -104 -105 -105 -105 -101 -105 -102 -105 -105 -105 -100 -105 -101 -105 -103 -105 -102 -105 -102 -105 -101 -105 -100 -105 -100 -105 -103 -105 -100 -101 -100 -105 -103 -105 -100 -100 -100 -105 Unit
TRx1-Ant
TRx2-Ant
IMD2
dBm
TRx3-Ant
TRx4-Ant Intermodulation distortion level in Rx band TRx1-Ant
TRx2-Ant
IMD3
dBm
TRx3-Ant
TRx4-Ant
Electrical characteristics are measured with all RF ports terminated in 50 and recommended circuit 2 (SP10T).
*1 *2 *3 *4 *5 *6 *7 *8 *9 *10 *11 *12
TRx port: +20dBm, 835MHz, TRx port: +20dBm, 835MHz, TRx port: +20dBm, 1880MHz, TRx port: +20dBm, 1880MHz, TRx port: +20dBm, 1950MHz, TRx port: +20dBm, 1950MHz, TRx port: +20dBm, 835MHz, TRx port: +20dBm, 835MHz, TRx port: +20dBm, 1880MHz, TRx port: +20dBm, 1880MHz, TRx port: +20dBm, 1950MHz, TRx port: +20dBm, 1950MHz,
Ant port: -15dBm, 45MHz Ant port: -15dBm, 1715MHz Ant port: -15dBm, 80MHz Ant port: -15dBm, 3840MHz Ant port: -15dBm, 190MHz Ant port: -15dBm, 4090MHz Ant port: -15dBm, 790MHz Ant port: -15dBm, 2550MHz Ant port: -15dBm, 1800MHz Ant port: -15dBm, 5720MHz Ant port: -15dBm, 1760MHz Ant port: -15dBm, 6040MHz
- 14 -
CXM3519ER
Electrical Characteristics (Recommended Circuit 2 (SP10T))
(VDD = 2.65V, Vctl = 1.80V, Ta = 25C)
Item Symbol Path 2nd harmonic 3rd harmonic 2nd harmonic 3rd harmonic 2nd harmonic 3rd harmonic 2nd harmonic 3rd harmonic 2nd harmonic 3rd harmonic 2nd harmonic 3rd harmonic Conditions 1648 to 1698MHz 1780 to 1830MHz 2472 to 2547MHz 2670 to 2745MHz 3420 to 3570MHz 3700 to 3820MHz 5130 to 5355MHz 5550 to 5730MHz 3840 to 3960MHz 5760 to 5940MHz 3840 to 3960MHz 5760 to 5940MHz 3840 to 3960MHz 5760 to 5940MHz 1648 to 1698MHz 2472 to 2547MHz C.W. Pin = +34dBm Min. -- -- -- -- -- -- -- -- -- -- -- -- Typ. -49 -44 -53 -45 -65 -63 -65 -62 -65 -60 -65 -65 Max -36 -36 -36 -36 -36 -36 dBm C.W. Pin = +26dBm -36 -36 -36 -36 -36 -36 Unit
Tx1-Ant *1
Tx2-Ant *2
C.W. Pin = +32dBm
TRx1-Ant *3 Harmonics Harm TRx2-Ant *3
C.W. Pin = +26dBm
TRx3-Ant *3
C.W. Pin = +26dBm
TRx4-Ant *4
C.W. Pin = +26dBm
Electrical characteristics are measured with all RF ports terminated in 50 and recommended circuit 2 (SP10T).
*1 *2 *3 *4
Frequency = 824 to 915MHz, Frequency = 1710 to 1910MHz, Frequency = 1920 to 1980MHz, Frequency = 824 to 849MHz,
Item Symbol
Pin on Tx1: +34dBm C.W. Pin on Tx2: +32dBm C.W. Pin on TRx1 or TRx2 or TRx3: +26dBm C.W. Pin on TRx4: +26dBm C.W.
Path Conditions 1648 to 1830MHz 2fo 3fo 4fo 2fo 3fo Min. 25 25 20 25 25 Typ. 35 35 24 33 32 Max. -- -- -- -- -- dB Unit
Tx1-Ant Attenuation ATT Tx2-Ant
2472 to 2745MHz 3296 to 3660MHz 3420 to 3820MHz 5130 to 5730MHz
Item Switching time Control current Supply current V.S.W.R.
Symbol Ts Ictl IDD V.S.W.R.
Path
Conditions 90% OFF to 90% ON
Min.
Typ. 2 --
Max. 5 10 0.4
Unit s A mA --
Active mode All ports in active paths 824 to 2170MHz
0.22 1.2
- 15 -
CXM3519ER
PCB Layout Template
VQFN-26P-01 Macro (Reference)
* PKG size : 3.8mm x 3.0mm * Pin pitch : 0.4mm
: Land : Mask (Open area) : Resist (Open area)
Metal mask thickness: 110m
4.2 3.8 (PKG line) 0.62 0.52 0.31 R0.2 0.72 0.62 0.37 R0.2 0.05 0.3 0.2 R0.05 C0.1 [Detailed view A] PKG line 0.21 0.26
3.0 (PKG line)
1.04
0.99 1.5 1.8 1.9
3.4
0.5
0.3
0.1 R0.2 R0.2 0.15 0.4
Mask corner R = 0.05mm A
- 16 -
CXM3519ER
Recommended PCB Design 1 (SP9T)
Ex.) GSM (4 bands) / UMTS (3 bands)
The positions of the light blue via holes and relative GND patterns are strongly recommended for getting stable attenuation.
0.78 1.20 1.67
1.72
(Unit: mm)
IC (VQFN-26P package) PCB metal pattern GND via hole for LPF (Light blue) GND via hole for switch
0.71 0.28
Independent GND with via hole
The positions of these via holes are recommended for stable attenuation.
- 17 -
CXM3519ER
Recommended PCB Design 2 (SP10T)
Ex.) GSM (4 bands) / UMTS (4 bands)
The positions of the light blue via holes and relative GND patterns are strongly recommended for getting stable attenuation.
0.78
1.20
1.67
1.72
(Unit: mm)
IC (VQFN-26P package) PCB metal pattern GND via hole for LPF (Light blue) GND via hole for switch
0.71 0.28
Independent GND with via hole
The positions of these via holes are recommended for stable attenuation.
- 18 -
CXM3519ER
Package Outline
(Unit: mm)
LEAD PLATING SPECIFICATIONS ITEM LEAD MATERIAL SOLDER COMPOSITION PLATING THICKNESS SPEC. COPPER ALLOY Sn-Bi Bi:1-4wt% 5-18m
- 19 -
Sony Corporation

▲Up To Search▲

Price & Availability of CXM3519ER

	To Download CXM3519ER Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .