![]() |
|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
EMP214-Q5 UPDATED 04/24/2008 12.50 - 15.50 GHz Surface-Mounted PA FEATURES * * * * * * 12.5 - 15.5 GHz Operating Frequency Range 29.5dBm Output Power at 1dB Compression 14.0 dB Typical Small Signal Gain -41dBc OIMD3 @Each Tone Pout 18.5dBm Point-to-point and point-to-multipoint radio Military Radar Systems APPLICATIONS Caution! ESD sensitive device. ELECTRICAL CHARACTERISTICS (Ta = 25 C, 50 ohm, VDD=7V, IDQ=750mA) SYMBOL F P1dB Gss OIMD3 Input RL Output RL Idss VDD Rth Tb PARAMETER/TEST CONDITIONS EMP214 - Q5 Operating Frequency Range EMP214H - Q5 EMP214L - Q5 Output Power at 1dB Gain Compression Small Signal Gain Output 3rd Order Intermodulation Distortion @f=10MHz, Each Tone Pout 18.5dBm Ids=60%10%Idss Input Return Loss Output Return Loss Saturate Drain Current VDS =3V, VGS =0V Power Supply Voltage Thermal Resistance 1 MIN 12.5 13.5 12.5 28.5 12.0 TYP MAX 15.5 15.5 14.5 UNITS GHz dBm dB 29.5 14.0 -41 -13 -13 -38 -10 -10 1380 dBc dB dB mA V o 920 1150 7 12 C/W C Operating Base Plate Temperature -35 +75 MAXIMUM RATINGS AT 25C2,3 SYMBOL VDS VGS IDD IGSF PIN TCH TSTG PT CHARACTERISTIC Drain to Source Voltage Gate to Source Voltage Drain Current Forward Gate Current Input Power Channel Temperature Storage Temperature Total Power Dissipation ABSOLUTE 12 V -8 V Idss 114mA 27dBm 175C -65/175C 12.4W CONTINUOUS 8V -4 V 1300mA 19mA @ 3dB compression 150C -65/150C 10.4W 1. Measured result when used with Excelics recommended evaluation board. 2. Operating the device beyond any of the above rating may result in permanent damage. 3. Bias conditions must also satisfy the following equation VDS*IDS < (TCH -THS)/RTH; where THS = Base Plate temperature Specifications are subject to change without notice. Excelics Semiconductor, Inc. 310 De Guigne Drive, Sunnyvale, CA 94085 Phone: 408-737-1711 Fax: 408-737-1868 Web: www.excelics.com Page 1 of 5 May 2008 EMP214-Q5 UPDATED 04/24/2008 12.50 - 15.50 GHz Surface-Mounted PA Top View Bottom View 0.1970.002 16 20 CHIP OUTLINE AND PIN ASSIGNMENT 0.1970.002 EMP214 -Q5 0 REF 0.1970.002 0.049 MAX 0.008 0 REF 0 REF 0.164 15 1 0.042 0.034 0.016 0 REF 11 5 10 6 0.0260.002 0.0120.002 Additional Notes: 1) Ground Plane must be soldered to PCB RF ground 2) All dimensions are in inches 3) Refer to Excelics application notes on QFNs for further guidelines 4) Pin Assignment: Top View Vd Bottom View Vd 16 20 RFin EMP214 -Q5 Vg 15 1 RFout RFout RFin 11 5 10 6 Vg Pin 1, 2, 4, 5 3 6 7, 8, 9, 10, 11, 12, 14, 15 13 16 17, 18, 19, 20 Assignment NC RFin Vg NC RFout Vd NC Specifications are subject to change without notice. Excelics Semiconductor, Inc. 310 De Guigne Drive, Sunnyvale, CA 94085 Phone: 408-737-1711 Fax: 408-737-1868 Web: www.excelics.com Page 2 of 5 May 2008 EMP214-Q5 UPDATED 04/24/2008 12.50 - 15.50 GHz Surface-Mounted PA Typical Performance: 1. Small-Signal Parameters(@Vds = 7V, Ids = 800mA) S21 S11 S22 2. P1-dB & G1-dB (@Vds = 7V, Ids = 800mA) 32 31 30 29 21 19 17 G1dB(dB) 15 13 11 9 7 5 15.5 P1dB(dBm) 28 27 26 25 24 23 22 12 12.5 13 13.5 14 14.5 15 Frequency(GHz) P1-dB G1-dB Specifications are subject to change without notice. Excelics Semiconductor, Inc. 310 De Guigne Drive, Sunnyvale, CA 94085 Phone: 408-737-1711 Fax: 408-737-1868 Web: www.excelics.com Page 3 of 5 May 2008 EMP214-Q5 UPDATED 04/24/2008 12.50 - 15.50 GHz Surface-Mounted PA 3. OIMD3 (@Vds = 7V, Ids = 800mA, f = 14.5GHz, f = 10MHz) 0 -10 -20 -30 -40 -50 -60 -70 -80 0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 Output Power Per Tone(dBm) OIMD3(dBc) OIMD3(dBc) Specifications are subject to change without notice. Excelics Semiconductor, Inc. 310 De Guigne Drive, Sunnyvale, CA 94085 Phone: 408-737-1711 Fax: 408-737-1868 Web: www.excelics.com Page 4 of 5 May 2008 EMP214-Q5 UPDATED 04/24/2008 12.50 - 15.50 GHz Surface-Mounted PA Recommended Circuit Schematic: 0.1uF 22uF Vd NC NC NC NC Vd NC NC NC NC RFin NC NC EMP214 -Q5 Vg NC NC NC NC RFout NC NC Vg 22uF 0.1uF Notes: 1) External bypass capacitors should be placed as close to the package as possible. 2) Dual biasing sequence required: a. Turn-on Sequence: Apply Vg = -2.5V, followed by Vd = 7V, lastly increase Vg until required Idq b. Turn-off Sequence: Turn off Vd, followed by Vg 3) Demonstration board available upon request. Specifications are subject to change without notice. Excelics Semiconductor, Inc. 310 De Guigne Drive, Sunnyvale, CA 94085 Phone: 408-737-1711 Fax: 408-737-1868 Web: www.excelics.com Page 5 of 5 May 2008 |
Price & Availability of EMP214-Q5
![]() |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |