View B0322J5050A00_4802286.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Model B0322J5050A00
Rev D
Ultra Low Profile 0805 Balun 50 to 50 Balanced
Description
The B0322J5050A00 is a low profile sub-miniature balanced to unbalanced transformer designed for differential inputs and output locations on next generation wireless chipsets in an easy to use surface mount package covering the GSM frequency. The B0322J5050A00 is ideal for high volume manufacturing and is higher performance than traditional ceramic and lumped element baluns. The B0322J5050A00 has an unbalanced port impedance of 50 and a 50 balanced port impedance. This transformation enables single ended signals to be applied to differential ports on modern semiconductors. The output ports have equal amplitude (-3dB) with 180 degree phase differential. The B0322J5050A00 is available on tape and reel for pick and place high volume manufacturing.
Detailed Electrical Specifications: Specifications subject to change without notice.
ROOM (25C)
Features:
* * * * * * * * * 300 - 2200 MHz 0.7mm Height Profile 50 Ohm to 2 x 25 Ohm Low Insertion Loss Input to Output DC Isolation Surface Mountable Tape & Reel Non-conductive Surface RoHS Compliant
Parameter Frequency Unbalanced Port Impedance Balanced Port Impedance Return Loss Insertion Loss* Amplitude Balance Phase Balance CMRR Power Handling Operating Temperature
Min. 300
Typ. 50 50 16 1.3 1.1 17 15
Max 2200
Unit MHz
12.2
1.6 1.2 20 2 +85
-55
dB dB dB Degrees dB Watts C
* Insertion Loss stated at room temperature (Insertion Loss is approximately 0.1 dB higher at +85 C)
Outline Drawing
Top View (Near-side) .079.004 [2.000.10] Side View Bottom View (Far-side)
.027.002 [0.700.05] .049.004 [1.250.10]
.026.004 [0.650.10] 1 2 3 6X .008 [0.20] Orientation Marker Denotes Pin Location
Orientation Marker Denotes Pin Location
Dimensions are in Inches [Millimeters] Mechanical Outline
Pin 1 2 3 4 5 6
Designation Unbalanced Port GND Balanced Port Balanced Port Do not connect NC
6 5 6X .012 [0.30]
4
Tolerances are Non-Cumulative
Available on Tape and Reel for Pick and Place Manufacturing.
USA/Canada: Toll Free: Europe:
(315) 432-8909 (800) 411-6596 +44 2392-232392
Model B0322J5050A00
Rev. D
Typical Broadband Performance: 0 MHz. to 8.5 GHz.
Return Loss - Input
0 -3 -6 -9 -12 -15
[dB]
[dB]
Insertion Loss
0 -0.3 -0.6 -0.9 -1.2 -1.5 -1.8 -2.1 -2.4 -2.7 -3 -3.3 -3.6
-18 -21 -24 -27 -30 -33 -36 0 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 6500 7000 7500 8000 8500
500
0
1000
1500
2000
2500
3000
3500
4000
4500
5000
5500
6000
6500
7000
7500
8000
8000
Frequency [MHz]
Frequency [MHz]
Amplitude Balance
2 1.5 1 0.5
[dB]
Phase Balance
20 15 10 5
deg
0 -0.5 -1 -1.5 -2 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 6500 7000 7500 8000 8500 0 500
0 -5 -10 -15 -20 0 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 6500 7000 7500 8500 500
Frequency [MHz]
Frequency [MHz]
CM RR
0 -3 -6 -9 -12 -15
[dB]
-18 -21 -24 -27 -30 -33 -36 0 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 6500 7000 7500 8000 8500
Frequency [MHz]
USA/Canada: Toll Free: Europe:
(315) 432-8909 (800) 411-6596 +44 2392-232392
Available on Tape and Reel for Pick and Place Manufacturing.
8500
Model B0322J5050A00
Rev D
Typical Performance: 200 MHz. to 2300 MHz.
Return Loss - Input
0 -3 -6 -9 -12 -15
[dB]
Insertion Loss
0 -0.3 -0.6 -0.9 -1.2 -1.5
[dB]
-18 -21 -24 -27 -30 -33 -36 1100 1400 1700 2000 2300 200 500 800
-1.8 -2.1 -2.4 -2.7 -3 -3.3 -3.6 200 500 800 1100 1400 1700 2000 2300
Frequency [MHz]
Frequency [MHz]
Amplitude Balance
2 1.5 1 0.5
[dB]
Phase Balance
20 15 10 5
deg
0 -0.5 -1 -1.5 -2 1100 1400 1700 2000 2300 200 500 800
0 -5 -10 -15 -20 200 500 800 1100 1400 1700 2000 2300
Frequency [MHz]
Frequency [MHz]
CM RR
0 -3 -6 -9 -12 -15
[dB]
-18 -21 -24 -27 -30 -33 -36 1100 1400 1700 2000 2300 200 500 800
Frequency [MHz]
Available on Tape and Reel for Pick and Place Manufacturing.
USA/Canada: Toll Free: Europe:
(315) 432-8909 (800) 411-6596 +44 2392-232392
Model B0322J5050A00
Rev. D
Mounting Configuration:
In order for Xinger surface mount components to work optimally, the proper impedance transmission lines must be used to connect to the RF ports. If this condition is not satisfied, insertion loss, Isolation and VSWR may not meet published specifications. All of the Xinger components are constructed from ceramic filled PTFE composites which possess excellent electrical o and mechanical stability having X and Y thermal coefficient of expansion (CTE) of 17 ppm/ C. An example of the PCB footprint used in the testing of these parts is shown below.In specific designs, the transmission line widths need to be adjusted to the unique dielectric coefficients and thicknesses as well as varying pick and place equipment tolerances.
6X .014 [0.35]
Plated thru hole to ground
6X .013 [0.33]
.026 [0.66]
6X .002 [0.05]
3X Transmission Line
4X .010 [0.25]
Circuit Pattern Footprint Pad (s) Solder Resist Dimensions are in Inches [Millimeters] Mounting Footprint
USA/Canada: Toll Free: Europe:
(315) 432-8909 (800) 411-6596 +44 2392-232392
Available on Tape and Reel for Pick and Place Manufacturing.
Model B0322J5050A00
Rev D
Packaging and Ordering Information
Parts are available in reel and are packaged per EIA 481-2. Parts are oriented in tape and reel as shown below. Minimum order quantities are 4000 per reel. See Model Numbers below for further ordering information.
OA
OC
OD
QUANTITY/REEL
4000
TABLE 1 REEL DIMENSIONS (inches [mm]) OA 7.00 [177.8] B 0.32 [8.0] 2.0 [50.8] OC OD 0.512 [13.0]
B
Available on Tape and Reel for Pick and Place Manufacturing.
USA/Canada: Toll Free: Europe:
(315) 432-8909 (800) 411-6596 +44 2392-232392

▲Up To Search▲

Price & Availability of B0322J5050A00

	To Download B0322J5050A00 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .