![]() |
|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
PROTECTION PRODUCTS - RailClamp(R) Description RailClamp(R) low capacitance TVS array designed to protect high speed data interfaces. This series has been specifically designed to protect sensitive components which are connected to data and transmission lines from overvoltage caused by ESD (electrostatic discharge), CDE (Cable Discharge Events), and EFT (electrical fast transients). The unique design incorporates surge rated, low capacitance steering diodes and a TVS diode in a single package. This allows the device to absorb large amounts of energy while protecting downstream components from harmful transient events. The RClamp(R)0504FA is in a 6-pin, SC-70 package. The leads are finished with lead-free matte tin. They may be used to meet the ESD immunity requirements of IEC 61000-4-2, Level 4 (15kV air, 8kV contact discharge). The combination of small size, low capacitance, and high ESD surge capability makes them ideal for use in applications such as USB 2.0, multimedia card, and video interfaces. RailClamp(R) Low Capacitance TVS Array Features Transient protection for high-speed data lines to IEC 61000-4-2 (ESD) 15kV (air), 8kV (contact) IEC 61000-4-4 (EFT) 40A (5/50ns) Array of surge rated diodes with internal TVS Diode Small package (2.4 x 2.2mm) saves board space Protects up to four I/O lines & power line Low capacitance (<3pF) for high-speed interfaces No insertion loss to 2.0GHz Low leakage current and clamping voltage Low operating voltage: 5.0V Solid-state silicon-avalanche technology RCLAMP0504FA Mechanical Characteristics EIAJ SC-70 6L package Lead Finish: Matte Tin Pb-Free, Halogen Free, RoHS/WEEE Compliant Molding compound flammability rating: UL 94V-0 Packaging : Tape and Reel Applications USB 2.0 USB OTG Monitors and Flat Panel Displays Digital Visual Interface (DVI) SIM Ports IEEE 1394 Firewire Ports Circuit Diagram Schematic & PIN Configuration 5 1 1 3 4 6 6 5 4 2 3 2 SC-70 6L (Top View) Revision 4/15/2010 1 www.semtech.com RCLAMP0504FA PROTECTION PRODUCTS Absolute Maximum Rating R ating Peak Pulse Power (tp = 8/20s) Peak Pulse Current (tp = 8/20s) ESD p er IEC 61000-4-2 (Air) ESD p er IEC 61000-4-2 (Contact) Op erating Temp erature Storage Temp erature Symbol Pp k IP P VESD TJ TSTG Value 150 6 15 8 -55 to +125 -55 to +150 Units Watts A kV C C Electrical Characteristics (T=25oC) Parameter Reverse Stand-Off Voltage Reverse Breakdown Voltage Reverse Leakage Current Clamp ing Voltage Clamp ing Voltage Junction Cap acitance Symbol VRWM V BR IR VC VC Cj Conditions Pi n 5 to 2 It = 1mA Pi n 5 to 2 VRWM = 5V, T=25C Pi n 5 to 2 IPP = 1A, tp = 8/20s A n y p i n to p i n 2 IPP = 6A, tp = 8/20s A n y p i n to p i n 2 VR = 0V, f = 1MHz Any I/O p in to p in 2 VR = 0V, f = 1MHz Between I/O p ins 6 3 15 25 3 1.5 Minimum Typical Maximum 5 Units V V A V V pF pF Note 1: I/O pins are pin 1, 3, 4, and 6 (c) 2010 Semtech Corp. 2 www.semtech.com RCLAMP0504FA PROTECTION PRODUCTS Typical Characteristics Non-Repetitive Peak Pulse Power vs. Pulse Time 10 Peak Pulse Power - PPP (kW) 110 100 % of Rated Power or PP I 90 80 70 60 50 40 30 20 10 Power Derating Curve 1 0.1 0.01 0.1 1 10 Pulse Duration - tp (s) 100 1000 0 0 25 50 75 100 125 150 Ambient Temperature - TA (oC) Pulse Waveform 110 100 90 80 70 60 50 40 30 20 10 0 0 5 10 15 Time (s) 20 25 30 td = IPP/2 PP Clamping Voltage vs. Peak Pulse Current Waveform Parameters: tr = 8s td = 20s 25 Waveform Parameters: tr = 8s td = 20s Clamping Voltage - VC (V) 20 Pin 1, 3, 4, or 6 to pin 2 Percent of I e -t 15 Pin 5 to pin 2 10 5 0 1 2 3 4 Peak Pulse Current - IPP (A) 5 6 Forward Voltage vs. peak Pulse Current 8 7 Forward Voltage - V F (V) Normalized Capacitance 2 Capacitance vs. Reverse Voltage (Normalized to 0V) f = 1MHz 1.5 Any I/O Pin to Pin 2 6 5 4 3 2 1 0 0 1 2 3 4 5 6 Waveform Parameters: tr = 8s td = 20s 1 0.5 0 0 1 2 3 4 5 Reverse Voltage - VR (V) Peak Pulse Current - IPP (A) (c) 2010 Semtech Corp. 3 www.semtech.com RCLAMP0504FA PROTECTION PRODUCTS Typical Characteristics Insertion Loss S21 (I/O to Pin 2) CH1 S21 LOG 6 dB / REF 0 dB Insertion Loss S21 (I/O to I/O) CH1 S21 LOG 6 dB / REF 0 dB START . 030 MHz STOP 3000. 000000 MHz START. 030 MHz . STOP 3000 000000 MHz Analog Crosstalk CH1 S21 LOG 20 dB/REF 0 dB ESD Response (8kV Contact per IEC 61000-4-2) START . 030 MHz STOP 3000. 000000 MHz Note: Data is taken with a 10x attenuator (c) 2010 Semtech Corp. 4 www.semtech.com RCLAMP0504FA PROTECTION PRODUCTS Applications Information Device Connection Options for Protection of Four High-Speed Data Lines This device is designed to protect data lines by clamping them to a fixed reference. When the voltage on the protected line exceeds the reference voltage the steering diodes are forward biased, conducting the transient current away from the sensitive circuitry. Data lines are connected at pins 1, 3, 4 and 6. Pin 2 should be connected directly to a ground plane. The path length is kept as short as possible to minimize parasitic inductance. The positive reference is connected at pin 5. The options for connecting the positive reference are as follows: 1. To protect data lines and the power line, connect pin 5 directly to the positive supply rail (VCC). In this configuration the data lines are referenced to the supply voltage. The internal TVS diode prevents over-voltage on the supply rail. 2. In applications where the supply rail does not exit the system, the internal TVS may be used as the reference. In this case, pin 5 is not connected. The steering diodes will begin to conduct when the voltage on the protected line exceeds the working voltage of the TVS (plus one diode drop). 3. In applications where complete supply isolation is desired, the internal TVS is again used as the reference and VCC is connected to one of the I/O inputs. An example of this configuration is the protection of a SIM port. The Clock, Reset, I/O, and VCC lines are connected at pins 1, 3, 4, and 6. Pin 2 is connected to ground and pin 5 is not connected. Matte Tin Lead Finish Matte tin has become the industry standard lead-free replacement for SnPb lead finishes. A matte tin finish is composed of 100% tin solder with large grains. Since the solder volume on the leads is small compared to the solder paste volume that is placed on the land pattern of the PCB, the reflow profile will be determined by the requirements of the solder paste. Therefore, these devices are compatible with both lead-free and SnPb assembly techniques. In addition, unlike other lead-free compositions, matte tin does not have any added alloys that can cause degradation of the solder joint. (c) 2010 Semtech Corp. 5 www.semtech.com Protection of Four Data Lines and Power Supply Line Protection of Four Data Lines Using Internal TVS Diode as Reference RCLAMP0504FA PROTECTION PRODUCTS Typical Applications SIM Port - Protection of Three Data Lines and VCC USB OTG Receptable Carkit To Phone Mini B Receptable VBus DD+ ID GND Shield Gnd 1 2 3 6 5 4 Mini A Receptable USB OTG Carkit Protection (c) 2010 Semtech Corp. 6 www.semtech.com RCLAMP0504FA PROTECTION PRODUCTS Typical Applications SD12 RCLAMP0504FA IEEE 1394 Firewire Protection (c) 2010 Semtech Corp. 7 www.semtech.com RCLAMP0504FA PROTECTION PRODUCTS Outline Drawing - SC70-6L DIMENSIONS INCHES MILLIMETERS MIN NOM MAX MIN NOM MAX .043 .004 .000 .028 .035 .039 .006 .012 .009 .003 .071 .079 .087 .045 .049 .053 .083 BSC .026 BSC .051 .010 .014 .018 (.017) 6 8 0 .004 .004 .012 1.10 0.00 0.10 0.70 0.90 1.00 0.15 0.30 0.08 0.22 1.80 2.00 2.20 1.15 1.25 1.35 2.10 BSC 0.65 BSC 1.30 BSC 0.26 0.36 0.46 (0.42) 6 0 8 0.10 0.10 0.30 A e1 N D DIM A A1 A2 b c D E1 E e e1 L L1 N 01 aaa bbb ccc A E/2 E1 E ccc C 2X N/2 TIPS 1 2 e B D aaa C SEATING PLANE C bxN bbb A1 A2 H C A-B D GAGE PLANE 0.15 L (L1) c 01 DETAIL SIDE VIEW NOTES: 1. CONTROLLING DIMENSIONS ARE IN MILLIMETERS (ANGLES IN DEGREES). A SEE DETAIL A 2. DATUMS -A- AND -B- TO BE DETERMINED AT DATUM PLANE -H3. DIMENSIONS "E1" AND "D" DO NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. 4. REFERENCE JEDEC STD MO-203, VARIATION AB. Land Pattern - SC70-6L X DIM C G Z C G P X Y Z DIMENSIONS INCHES MILLIMETERS (.073) .039 .026 .016 .033 .106 (1.85) 1.00 0.65 0.40 0.85 2.70 Y P NOTES: 1. THIS LAND PATTERN IS FOR REFERENCE PURPOSES ONLY. CONSULT YOUR MANUFACTURING GROUP TO ENSURE YOUR COMPANY'S MANUFACTURING GUIDELINES ARE MET. (c) 2010 Semtech Corp. 8 www.semtech.com RCLAMP0504FA PROTECTION PRODUCTS Marking Ordering Information Part Number Qty per Reel 3,000 Reel Size 7 Inch 0504F YYWW Note: YYWW = Date Code RClamp 0504FATCT RailClamp and RClamp are trademarks of Semtech Corporation Tape and Reel Specification 0504F YYWW 0504F YYWW 0504F YYWW 0504F YYWW 0504F YYWW 0504F YYWW 0504F YYWW 0504F YYWW Device Orientation in Tape A0 2.40 +/-0.15 mm B0 2.40 +/-0.15 mm K0 1.20 +/-0.15 mm Tape Width B, (Max) D D1 E F K (MAX) P P0 P2 T(MAX) W 8.0 mm + 0.3 mm - 0.1 mm 8 mm 4.2 mm 1.5 + 0.1 mm - 0.0 mm ) 0.5 mm 0.05 1.750.10 mm 3.50.05 mm 2.4 mm 4.00.1 mm 4.00.1 mm 2.00.05 mm 0.4 mm Contact Information Semtech Corporation Protection Products Division 200 Flynn Rd., Camarillo, CA 93012 Phone: (805)498-2111 FAX (805)498-3804 (c) 2010 Semtech Corp. 9 www.semtech.com |
Price & Availability of RCLAMP0504FA
![]() |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |