|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
Features * Protocol - USB Used as Physical Layer - Device Firmware Upgrade Class Compliant - USB Clock Auto-Configuration * In-System Programming - Read/Write Flash and EEPROM Memories - Read Device ID - Full-chip Erase - Read/Write Configuration Bytes - Security Setting from ISP Command - Remote Application Start Command * In-Application Programming/Self Programming (IAP) - Read/Write Flash and EEPROM Memories - Read Device ID - Block Erase - Read/Write Configuration Bytes - Bootloader Start USB Microcontrollers AT89C5131A USB Bootloader Description This document describes the USB bootloader functionalities as well as the USB protocol to efficiently perform operations on the on-chip Flash (EEPROM) memories. Additional information on the AT89C5131A product can be found in the AT89C5131A datasheet and the AT89C5131A errata sheet available on the Atmel web site. The bootloader software package (binary) currently used for production is available from the Atmel web site. Bootloader Revision Revision 1.0.2 Revision 1.2.0 Purpose of Modifications First release Bootloader improvement Date 25/03/2003 20/03/2007 4287E-USB-04/08 Functional Description In-System Programming Capability (IAP) The AT89C5131A bootloader facilitates In-System Programming and In-Application Programming. In-System Programming allows the user to program or reprogram a microcontroller on-chip Flash memory without removing it from the system and without the need of a pre-programmed application. The USB bootloader can manage a communication with a host through the USB bus. It can also access and perform requested operations on the on-chip Flash memory. In-Application Programming or Self Programming Capability (ISP) Block Diagram In-Application Programming (IAP) allows the reprogramming of a microcontroller on-chip Flash memory without removing it from the system and while the embedded application is running. The USB bootloader contains some Application Programming Interface routines named API routines that allow IAP by using the user's firmware. This section describes the different parts of the bootloader. Figure 1 shows the on-chip bootloader and IAP processes. Figure 1. Bootloader Process Description On-chip User Application External Host Via the USB Protocol Communication ISP Communication Management IAP User Call Management Flash Memory Management Flash Memory 2 AT89C5131A USB Bootloader 4287E-USB-04/08 AT89C5131A USB Bootloader ISP Communication Management The purpose of this process is to manage the communication and its protocol between the onchip bootloader and an external device (host). The on-chip bootloader implements a USB protocol (see section "Protocol"). This process translates serial communication frames (USB) into Flash memory accesses (read, write, erase...). User Call Management Several Application Program Interface (API) calls are available to the application program to selectively erase and program Flash pages. All calls are made through a common interface (API calls) included in the bootloader. The purpose of this process is to translate the application request into internal Flash memory operations. Flash Memory Management This process manages low level access to the Flash memory (performs read and write access). Bootloader Configuration Configuration and Manufacturer Information The table below lists Configuration and Manufacturer byte information used by the bootloader. This information can be accessed through a set of API or ISP commands. Mnemonic BSB SBV SSB EB P1_CF P3_CF P4_CF Manufacturer Id1: Family code Id2: Product Name Id3: Product Revision Description Boot Status Byte Software Boot Vector Software Security Byte Extra Byte Port 1 Configuration Port 3 Configuration Port 4 Configuration Default Value FFh FCh FFh FFh FEh FFh FFh 58h D7h F7h DFh 3 4287E-USB-04/08 Mapping and Default Value of Hardware Security Byte The 4 MSB of the Hardware Byte can be read/written by software (this area is called Fuse bits). The 4 LSB can only be read by software and written by hardware in parallel mode (with parallel programmer devices). Bit Position 7 6 5 4 3 2 1 0 Mnemonic X2B BLJB OSCON1 OSCON0 reserved LB2 LB1 LB0 Default Value U P U U U P U U To lock the chip (see datasheet) Description To start in x1 mode To map the boot area in code area between F800h-FFFFh Oscillator control (bit 1) Oscillator control (bit 0) Note: U: Unprogrammed = 1 P: Program = 0 Security The bootloader has Software Security Byte (SSB) to protect itself from user access or ISP access. The Software Security Byte (SSB) protects from ISP accesses. The command "Program Software Security Bit" can only write a higher priority level. There are three levels of security: * Level 0: NO_SECURITY (FFh) This is the default level. From level 0, one can write level 1 or level 2. Level 1: WRITE_SECURITY (FEh) In this level it is impossible to write in the Flash memory. The Bootloader returns an err_WRITE status. From level 1, one can write only level 2. Level 2: RD_WR_SECURITY (FCh) Level 2 forbids all read and write accesses to/from the Flash memory. The Bootloader returns an err_WRITE or an err_VENDOR status. * * Only a full chip erase command can reset the software security bits. Level 0 Flash/EEPROM Fuse bit BSB & SBV & EB SSB Manufacturer info Bootloader info Erase block Full chip erase Blank Check Any access allowed Any access allowed Any access allowed Any access allowed Read only access allowed Read only access allowed Allowed Allowed Allowed Level 1 Read only access allowed Read only access allowed Any access allowed Write level2 allowed Read only access allowed Read only access allowed Not allowed Allowed Allowed Level 2 All access not allowed All access not allowed Any access allowed Read only access allowed Read only access allowed Read only access allowed Not allowed Allowed Allowed 4 AT89C5131A USB Bootloader 4287E-USB-04/08 AT89C5131A USB Bootloader In-System Programming ISP allows the user to program or reprogram a microcontroller's on-chip Flash memory through the USB bus without removing it from the system and without the need of a pre-programmed application. This section describes how to start the USB bootloader and the higher level protocol over the USB. Boot Process The bootloader can be activated in two ways: * * Hardware conditions Regular boot process Figure 3 and Figure 4 describe the boot process flows for low pin count and high pin count products. High Pin Count Hardware Conditions The Hardware conditions (EA = 1, PSEN = 0) during the RESET rising edge force the on-chip bootloader execution. In this way the bootloader can be carried out regardless of the user Flash memory content. It is recommended to pull the PSEN pin down to ground though a 1K resistor to prevent the PSEN pin from being damaged (see Figure 2 below). Figure 2. ISP Hardware conditions VCC VCC VCC EA ALE Unconnected C2 RST XTAL2 GND Crystal GND C1 Bootloader /PSEN XTAL1 1K GND GND VSS GND As PSEN is an output port in normal operating mode (running user application or bootloader code) after reset, it is recommended to release PSEN after rising edge of reset signal. The hardware conditions are sampled at reset signal rising edge, thus they can be released at any time when reset input is high. Low Pin Count Hardware Conditions The Hardware Condition forces the bootloader execution from reset. The default factory Hardware Condition is assigned to port P1. * P1 must be equal to FEh In order to offer the best flexibility, the user can define its own Hardware Condition on one of the following Ports: * Port1 5 4287E-USB-04/08 * * Port3 Port4 (only bit0 and bit1) The Hardware Condition configuration are stored in three bytes called P1_CF, P3_CF, P4_CF. These bytes can be modified by the user through a set of API or through an ISP command. There is a priority between P1_CF, P3_CF and P4_CF (see Figure 4 on page 9). Note: The BLJB must be at 0 (programmed) to be able to restart the bootloader. If the BLJB is equal to 1 (unprogrammed) only the hardware parallel programmer can change this bit (see AT89C5131A datasheet for more details). 6 AT89C5131A USB Bootloader 4287E-USB-04/08 AT89C5131A USB Bootloader Software Boot Vector The default value [FF]00h is used in ISP mode. The boot address is, in this mode, the lowest adress of FM1 USB bootloader. The Software Boot Vector (SBV) can be used to force the execution of a user bootloader starting at address [SBV]00h in the application area (FM0). The way to start this user bootloader is described in section "Boot Process". USB Bootloader [FC]00h User Bootloader Application [SBV]00h FM1 FM0 FLIP Software Program FLIP is a PC software program running under Windows(R) 9x/Me/2000/XP and Linux(R) which can be used in ISP mode and which supports all Atmel C51 Flash microcontroller and USB protocol communication media. The FLIP software program is free and is available from the Atmel web site. 7 4287E-USB-04/08 Figure 3. High-pin Count Regular Boot Process RESET B it E N B O O T in A U XR 1 R egis ter is Initialized with B LJ B inverted ENBOOT = 1 P C = F 400h F C O N = 00h Hardware Boot Process H ardw are C ondition No ENBOOT = 0 P C = 0000h Y es Y es B LJ B = 1 ENBOOT = 1 P C = F 400h F C O N = 0F h No Software Boot Process F C O N = 00h Y es No S B V < 7F h No Y es S ta rt A p p lica tio n S ta rt U se r B o o tlo a d e r S ta rt B o o tlo a d e r 8 AT89C5131A USB Bootloader 4287E-USB-04/08 AT89C5131A USB Bootloader Figure 4. Low-pin Count Regular Boot Process RESET Bit ENBOOT in AUXR1 Register is Initialized with BLJB Inverted Hardware Boot Process ENBOOT = 0 PC = 0000h Yes BLJB = 1 ENBOOT = 1 PC = F400h No No P1_CF = FFh Yes No P1_CF = P1 Yes No P3_CF = FFh Yes Software Boot Process No P3_CF = P3 No P4_CF = FFh Yes Yes No P4_CF = P4 Yes BSB = 0 Yes No SBV < 7Fh Yes No Start Application Start User Bootloader Start Bootloader 9 4287E-USB-04/08 Physical Layer The USB norm specifies all the transfers over the USB line. The USB specification also includes several CLASS and SUB-CLASS specifications. These stand-alone documents are used by the manufacturer to implement a USB link between a PC and a device supporting the In System Programming. Mostly, the USB specification is implemented by hardware (automatic reply, handshakes, timings, ...) and the USB Classes and SubClasses are implemented by software at a data level. Figure 5. USB Bus Topography Downstream Transfer: OUT Upstream Transfer: IN PC Driver PC Application USB Line Application (Device) PC (Host) The USB is used to transmit information that has the following configuration: * * USB DFU using the Default Control Endpoint only (endpoint 0) with a 32 bytes length. 48 MHz for USB controller: USB clock configuration performed by the bootloader Device driver/API Firmware 48 MHz Frequency Auto-Configuration The bootloader includes a function which will automatically setup the PLL frequency (48MHz) versus the different XTAL configuration used on the application. The table below shows the allowed frequencies compatible with the USB bootloader 48 MHz auto-generation. 6 MHz X1 or X2 Clock Modes 8 MHz 12 MHz 16 MHz 20 MHz 24 MHz 32 MHz 40 MHz 48 MHz OK OK OK OK OK OK OK OK OK 10 AT89C5131A USB Bootloader 4287E-USB-04/08 AT89C5131A USB Bootloader Figure 6. 48 MHz Frequency Auto-Configuration MAIN No USB Connected? Suspend/Resume No Yes Resume Detected? Yes Configure PLL for Frequency X Configure Timer 0 Yes SOF Detected? No Timer 0 Overflow? No Yes Change Frequency USB Scheduler 11 4287E-USB-04/08 Protocol Device Firmware Upgrade Introduction Device Firmware Upgrade is the mechanism for accomplishing the task of upgrading the device firmware. Any class of USB device can exploit this capability by supporting the requirements specified in this document. Because it is impractical for a device to concurrently perform both DFU operations and its normal run-time activities, those normal activities must cease for the duration of the DFU operations. Doing so means that the device must change its operating mode; i.e., a printer is not a printer while it is undergoing a firmware upgrade; it is a PROM programmer. However, a device that supports DFU is not capable of changing its mode of operation on its own. External (human or host operating system) intervention is required. DFU Specific Requests In addition of the USB standard requests, 7 DFU class-specific requests are employed to accomplish the upgrade operations (Table 1): Table 1. DFU Class-specific Requests bmRequestType 0010 0001b 0010 0001b 1010 0001b 1010 0001b 0010 0001b 1010 0001b 0010 0001b bRequest DFU_DETACH (0) DFU_DNLOAD (1) DFU_UPLOAD (2) DFU_GETSTATUS (3) DFU_CLRSTATUS (4) DFU_GETSTATE (5) DFU_ABORT (6) wValue wTimeout wBlock wBlock Zero Zero Zero Zero wIndex Interface (4) Interface (4) Interface (4) Interface (4) Interface (4) Interface (4) Interface (4) wLength Zero Length Length 6 Zero 1 Zero Data none Firmware Firmware Status none State none DFU Descriptors Set The device exports the DFU descriptor set, which contains: * * * * A DFU device descriptor A single configuration descriptor A single interface descriptor (including descriptors for alternate settings, if present) A single functional descriptor DFU Device Descriptor This descriptor is only present in the DFU mode descriptor set. The DFU class code is reported in the bDeviceClass field of this descriptor. Table 2. USB Parameters Parameter Vendor ID Product ID Release Number Atmel - AT89C5131A Bootloader 0x03EB 0x2FFD 0x0000 12 AT89C5131A USB Bootloader 4287E-USB-04/08 AT89C5131A USB Bootloader Table 3. DFU Mode Device Descriptor Offset 0 1 2 4 5 6 7 8 10 12 14 15 16 17 Field bLength bDescriptorType bcdUSB bDeviceClass bDeviceSubClass bDeviceProtocol bMaxPacketSize0 idVendor idProduct bcdDevice iManufacturer iProduct iSerialNumber bNumConfigurations Size 1 1 2 1 1 1 1 2 2 2 1 1 1 1 Value 12h 01h 0100h FEh 01h 00h 32 03EBh 2FFDh 0x0000 0 0 0 01h Description Size of this descriptor, in bytes DFU FUNCTIONAL descriptor type USB specification release number in binary coded decimal Application Specific Class Code Device Firmware Upgrade Code The device does not use a class specific protocol on this interface Maximum packet size for endpoint zero Vendor ID Product ID Device release number in binary coded decimal Index of string descriptor Index of string descriptor Index of string descriptor One configuration only for DFU DFU Configuration Descriptor This descriptor is identical to the standard configuration descriptor described in the USB DFU specification version 1.0, with the exception that the bNumInterfaces field must contain the value 01h. This is the descriptor for the only interface available when operating in DFU mode. Therefore, the value of the bInterfaceNumber field is always zero. DFU Interface Descriptor Table 4. DFU Mode Interface Descriptor Offset 0 1 2 3 4 5 6 7 8 Field bLength bDescriptorType bInterfaceNumber bAlternateSetting bNumEndpoints bInterfaceClass bInterfaceSubClass bInterfaceProtocol iInterface Size 1 1 1 1 1 1 1 1 1 Value 09h 04h 00h 00h 00h FEh 01h 00h 00h Description Size of this descriptor, in bytes INTERFACE descriptor type Number of this interface Alternate setting(1) Only the control pipe is used Application Specific Class Code Device Firmware Upgrade Code The device doesn't use a class specific protocol on this interface Index of the String descriptor for this interface Note: 1. Alternate settings can be used by an application to access additional memory segments. In this case, it is suggested that each alternate setting employ a string descriptor to indicate the target memory segment; e.g., "EEPROM". Details concerning other possible uses of alternate settings are beyond the scope of this document. However, their use is intentionally not restricted because the authors anticipate that implementers will devise additional creative uses for alternate settings. 13 4287E-USB-04/08 DFU Functional Descriptor Table 5. DFU Functional Descriptor Offset 0 1 Field bLength bDescriptorType Size 1 1 Value 07h 21h Description Size of this descriptor, in bytes DFU FUNCTIONAL descriptor type DFU Attributes: bit 7..3: reserved bit 2: device is able to communicate via USB after Manifestation phase 1 = yes, 0 = no, must see bus reset bit 1: bitCanUpload : upload capable 1 = yes, 0 = no bit 0: bitCanDnload : download capable 1 = yes, 0 = no Time in milliseconds that the device will wait after receipt of the DFU_DETACH request. 2 bmAttributes 1 Bit mask 3 wDetachTimeOut 2 Number If this time elapses without a USB reset, the device will terminate the Reconfiguration phase and revert back to normal operation. This represents the maximum time that the device can wait (depending on its timers, ...). The Host may specify a shorter timeout in the DFU_DETACH request. Maximum number of bytes that the device can accept per controlwrite transaction 5 wTransferSize 2 Number Command Description This protocol allows to: * * * * * * * Initiate the communication Program the Flash or EEPROM Data Read the Flash or EEPROM Data Program Configuration Information Read Configuration and Manufacturer Information Erase the Flash Start the application Overview of the protocol is detailed in Appendix-A. 14 AT89C5131A USB Bootloader 4287E-USB-04/08 AT89C5131A USB Bootloader Device Status Get Status The Host employs the DFU_GETSTATUS request to facilitate synchronization with the device. This status gives information on the execution of the previous request: in progress/OK/Fail/... bmRequestType 1010 0001b 0010 0001b bRequest DFU_GETSTATUS (3) DFU_CLRSTATUS (4) wValue Zero Zero wIndex Interface (4) Interface (4) wLength 6 Zero Data Status none The device responds to the DFU_GETSTATUS request with a payload packet containing the following data: Table 6. DFU_GETSTATUS Response Offset 0 Field bStatus Size 1 Value Numb er Description An indication of the status resulting from the execution of the most recent request. Minimum time in milliseconds that the host should wait before sending a subsequent DFU_GETSTATUS. The purpose of this field is to allow the device to dynamically adjust the amount of time that the device expects the host to wait between the status phase of the next DFU_DNLOAD and the subsequent solicitation of the device's status via DFU_GETSTATUS. An indication of the state that the device is going to enter immediately following transmission of this response. Index of status description in string table. 1 bwPollTimeOut 3 Numb er 4 bState 1 Numb er Index 5 iString 1 Table 7. bStatus values Status OK errTARGET errFILE errWRITE errERASE errCHECK_ERASED errPROG errVERIFY errADDRESS errNOTDONE errFIRMWARE errVENDOR Value 0x00 0x01 0x02 0x03 0x04 0x05 0x06 0x07 0x08 0x09 0x0A 0x0B Description No error condition is present File is not targeted for use by this device File is for this device but fails some vendor-specific verification test Device id unable to write memory Memory erase function failed Memory erase check failed Program memory function failed Programmed memory failed verification Cannot program memory due to received address that is out of range Received DFU_DNLOAD with wLength = 0, but device does not think it has all the data yet. Device's firmware is corrupted. It cannot return to run-time operations iString indicates a vendor-specific error 15 4287E-USB-04/08 Table 7. bStatus values (Continued) Status errUSBR errPOR errUNKNOWN errSTALLEDPK Value 0x0C 0x0D 0x0E 0x0F Description Device detected unexpected USB reset signaling Device detected unexpected power on reset Something went wrong, but the device does not know what it was Device stalled an unexpected request Table 8. bState Values State appIDLE appDETACH dfuIDLE dfuDNLOAD-SYNC dfuDNBUSY dfuDNLOAD-IDLE Value 0 1 2 3 4 5 Description Device is running its normal application Device is running its normal application, has received the DFU_DETACH request, and is waiting for a USB reset Device is operating in the DFU mode and is waiting for requests Device has received a block and is waiting for the Host to solicit the status via DFU_GETSTATUS Device is programming a control-write block into its non volatile memories Device is processing a download operation. Expecting DFU_DNLOAD requests Device has received the final block of firmware from the Host and is waiting for receipt of DFU_GETSTATUS to begin the Manifestation phase dfuMANIFEST-SYNC 6 or device has completed the Manifestation phase and is waiting for receipt of DFU_GETSTATUS. dfuMANIFEST dfuMANIFEST-WAITRESET dfuUPLOAD-IDLE dfuERROR 7 8 Device is in the Manifestation phase. Device has programmed its memories and is waiting for a USB reset or a power on reset. The device is processing an upload operation. Expecting DFU_UPLOAD requests. An error has occurred. Awaiting the DFU_CLRSTATUS request. 9 10 Clear Status Any time the device detects an error and reports an error indication status to the host in the response to a DFU_GETSTATUS request, it enters the dfuERROR state. The device cannot transition from the dfuERROR state, after reporting any error status, until after it has received a DFU_CLRSTATUS request. Upon receipt of DFU_CLRSTATUS, the device sets a status of OK and transitions to the dfuIDLE state. Only then is it able to transition to other states. bmRequestType 0010 0001b bRequest DFU_CLRSTATUS (4) wValue Zero wIndex Interface (4) wLength 0 Data None 16 AT89C5131A USB Bootloader 4287E-USB-04/08 AT89C5131A USB Bootloader Device State This request solicits a report about the state of the device. The state reported is the current state of the device with no change in state upon transmission of the response. The values specified in the bState field are identical to those reported in DFU_GETSTATUS. bmRequestType 1010 0001b bRequest DFU_GETSTATE (5) wValue Zero wIndex Interface (4) wLength 1 Data State DFU_ABORT request The DFU_ABORT request enables the device to exit from certain states and return to the DFU_IDLE state. The device sets the OK status on receipt of this request. For more information, see the corresponding state transition summary. bmRequestType 1010 0001b bRequest DFU_ABORT (6) wValue Zero wIndex Interface (4) wLength 0 Data None Programming the Flash or EEPROM Data The firmware image is downloaded via control-write transfers initiated by the DFU_DNLOAD class-specific request. The host sends between bMaxPacketSize0 and wTransferSize bytes to the device in a control-write transfer. Following each downloaded block, the host solicits the device status with the DFU_GETSTATUS request. As described in the USB DFU Specification, "Firmware images for specific devices are, by definition, vendor specific. It is therefore required that target addresses, record sizes, and all other information relative to supporting an upgrade are encapsulated within the firmware image file. It is the responsibility of the device manufacturer and the firmware developer to ensure that their devices can consume these encapsulated data. With the exception of the DFU file suffix, the content of the firmware image file is irrelevant to the host." Firmware image: * * 32 bytes: Command X bytes: X is the number of byte (00h) added before the first significative byte of the firmware. The X number is calculated to align the beginning of the firmware with the flash page. X = start_address [32]. For example, if the start address is 00AFh (175d), X = 175 [32] = 15. The firmware The DFU Suffix on 16 Bytes. * * Table 9. DFU File Suffix Offset -0 -4 Field dwCRC bLength Size 4 1 Value Number 16 5 : 44h Description The CRC of the entire file, excluding dwCRC The length of this DFU suffix including dwCRC -5 ucDfuSignature 3 6 : 46h 7 : 55h The unique DFU signature field -8 bcdDFU 2 BCD 0100h ID DFU specification number The vendor ID associated with this file. Either FFFFh or must match device's vendor ID -10 idVendor 2 17 4287E-USB-04/08 Offset -12 Field idProduct Size 2 Value ID Description The product ID associated with this file. Either FFFFf or must match the device's product ID The release number of the device associated with this file. Either FFFFh or a BCD firmware release or version number -14 bcdDevice 2 BCD Request From Host bmRequestType 0010 0001b bRequest DFU_DNLOAD (1) wValue wBlock wIndex Interface (4) wLength Length Data Firmware Write Command Command Identifier Id_prog_start 01h 01h data[0] 00h data[1] data[2] data[3] data[4] Description Init FLASH programming start_address end_address Init EEPROM programming The write command is 6 bytes long. In order to reach the USB specification of the Control type transfers, the write command is completed with 26 (= 32 - 6) non-significant bytes. The total length of the command is then 32 bytes, which is the length of the Default Control Endpoint. Firmware The firmware can now be downloaded to the device. In order to be in accordance with the Flash page size (128 bytes), X non-significant bytes are added before the first byte to program. The X number is calculated to align the beginning of the firmware with the Flash page. X = start_address [32]. For example, if the start address is 00AFh (175d), X = 175 [32] = 15. The DFU suffix of 16 bytes are added just after the last byte to program. This suffix is reserved for future use. DFU Suffix 18 AT89C5131A USB Bootloader 4287E-USB-04/08 AT89C5131A USB Bootloader Figure 7. Example of Firmware Download Zero Length DFU_DNLOAD Request SETUP OUT OUT OUT DFU_DNLOAD Prog_Start + (EP0 fifo length - 6) x 00h X offset bytes + Firmware Packet 1 Firmware Packet 2 OUT IN Firmware Packet n + DFU suffix ZLP The Host sends a DFU_DNLOAD request with the wLength field cleared to 0 to the device to indicate that it has completed transferring the firmware image file. This is the final payload packet of a download operation. This operation should be preceded by a Long Jump address specification using the corresponding Flash command. Answers from Bootloader After each program request, the Host can request the device state and status by sending a DFU_GETSTATUS message. If the device status indicates an error, the host can send a DFU_CLRSTATUS request to the device. 19 4287E-USB-04/08 Reading the Flash or EEPROM Data The flow described below allows the user to read data in the Flash memory or in the EEPROM data memory. A blank check command on the Flash memory is possible with this flow. This operation is performed in 2 steps: 1. DFU_DNLOAD request with the read command (6 bytes) 2. DFU_UPLOAD request which correspond to the immediate previous command. First Request from Host The Host sends a DFU Download request with a Display command in the data field. SETUP OUT IN DFU_DNLOAD Display_Data (6 bytes) ZLP Command Identifier data[0] 00h data[1] data[2] data[3] data[4] Description Display FLASH Data Id_display_data 03h 01h 02h start_address end_address Blank Check in FLASH Display EEPROM Data Second Request from Host Answers from the Device The Host sends a DFU Upload request. The device send to the Host the firmware from the specified start address to the end address. SETUP IN IN DFU_UPLOAD Firmware Packet 1 Firmware Packet 2 IN OUT Firmware Packet n ZLP 20 AT89C5131A USB Bootloader 4287E-USB-04/08 AT89C5131A USB Bootloader Answers from the Device to a Blank Check Command The Host controller send a GET_STATUS request to the device. Once internal blank check has been completed, the device sends its status. * * If the device status is "OK": the device memory is then blank and the device waits the next Host request. If the device status is "errCHECK_ERASED": the device memory is not blank. The device waits for an DFU_UPLOAD request to send the first address where the byte is not 0xFF. Programming Configuration Information The flow described below allows the user to program Configuration Information regarding the bootloader functionality. * Boot Process Configuration: - - - - BSB SBV P1_CF, P3_CF and P4_CF Fuse bits (BLJB, X2 and OSCON bits) (see section "Mapping and Default Value of Hardware Security Byte") Take care that the Program Fuse bit command programs the 4 Fuse bits at the same time. Request from Host To start the programming operation, the Host sends DFU_DNLOAD request with the Write command in the data field (6 bytes). SETUP OUT IN DFU_DNLOAD Write_command (6 bytes) ZLP Command Identifier data[0] data[1] 00h 01h 02h data[2] data[3] data[4] Description Write value in BSB Write value in SBV Write P1_CF 01h Id_write_command 04h 03h 04h 05h 06h Value Write P3_CF Write P4_CF Write value in SSB Write value in EB 02h 00h Value Write value in Fuse (HSB) Answers From Bootloader The device has two possible answers to a DFU_GETSTATUS request: * * If the chip is protected from program access, a "err_WRITE" status is returned to the Host. Otherwise, the device status is "OK". 21 4287E-USB-04/08 Reading Configuration Information or Manufacturer Information Requests From Host The flow described below allows the user to read the configuration or manufacturer information. To start the programming operation, the Host sends DFU_DNLOAD request with the Read command in the data field (2 bytes). SETUP OUT IN DFU_DNLOAD Read_command (2 bytes) ZLP Command Identifier data[0] data[1] 00h data[2] data[3] data[4] Description Read Bootloader Version Read Device boot ID1 Read Device boot ID2 Read BSB Read SBV Read P1_CF Read P3_CF Read P4_CF Read SSB Read EB Read Manufacturer Code Read Family Code Read Product Name Read Product Revision Read HWB 00h 01h 02h 00h 01h 02h 03h Id_read_command 05h 01h 04h 05h 06h 30h 31h 60h 61h 02h 00h 22 AT89C5131A USB Bootloader 4287E-USB-04/08 AT89C5131A USB Bootloader Answers from Bootloader The device has two possible answers to a DFU_GETSTATUS request: * * If the chip is protected from program access, an "err_VENDOR" status is returned to the Host. Otherwise, the device status is "OK". The Host can send a DFU_UPLOAD request to the device in order the value of the requested field. SETUP IN OUT DFU_UPLOAD Byte value (1 byte) ZLP Erasing the Flash The flow described below allows the user to erase the Flash memory. Two modes of Flash erasing are possible: * * Full Chip erase Block erase The Full Chip erase command erases the whole Flash (32 Kbytes) and sets some Configuration Bytes at their default values: * * * BSB = FFh SBV = FFh SSB = FFh (NO_SECURITY) The Block erase command erases only a part of the Flash. Three Blocks are defined in the AT89C5131A: * * * Request from Host block0 (From 0000h to 1FFFh) block1 (From 2000h to 3FFFh) block2 (From 4000h to 7FFFh) To start the erasing operation, the Host sends a DFU_DNLOAD request with a Write Command in the data field (2 bytes). Command Identifier data[0] data[1] 00h 20h data[2] data[3] data[4] Description Erase block0 (0K to 8K) Erase block1 (8K to 16K) Erase block2 (16K to 32K) Full chip Erase (bits at FFh) Id_write_command 04h 00h 40h FFh 23 4287E-USB-04/08 Answers from Bootloader The device has two possible answers to a DFU_GETSTATUS request: * * If the chip is protected from program access, a "err_WRITE" status is returned to the Host. Otherwise, the device status is "OK". The full chip erase is always executed whatever the Software Security Byte value is. Starting the Application The flow described below allows to start the application directly from the bootloader upon a specific command reception. Two options are possible: * Start the application with a reset pulse generation (using watchdog). When the device receives this command the watchdog is enabled and the bootloader enters a waiting loop until the watchdog resets the device. Take care that if an external reset chip is used the reset pulse in output may be wrong and in this case the reset sequence is not correctly executed. Start the application without reset A jump at the address 0000h is used to start the application without reset. * To start the application, the Host sends a DFU_DNLOAD request with the specified application start type in the data field (3 or 5bytes). This request is immediately followed by a second DFU_DNLOAD request with no data field to start the application with one of the 2 options. Request From Host SETUP IN OUT DFU_UPLOAD Jump Option (3 or 5 Bytes) ZLP SETUP DFU_UPLOAD Command Identifier Id_write_command 04h data[0] data[1] 00h data[2] data[3] data[4] Description Hardware reset 03h 01h address LJMP address Answer from Bootloader No answer is returned by the device. 24 AT89C5131A USB Bootloader 4287E-USB-04/08 AT89C5131A USB Bootloader In-Application Programming/S elf Programming The IAP allows to reprogram a microcontroller on-chip Flash memory without removing it from the system and while the embedded application is running. The user application can call Application Programming Interface (API) routines allowing IAP. These API are executed by the bootloader. To call the corresponding API, the user must use a set of Flash_api routines which can be linked with the application. Example of Flash_api routines are available on the Atmel web site on the software package: C Flash Drivers for the AT89C5131A for Keil(R) Compilers The flash_api routines on the package work only with the USB bootloader. The flash_api routines are listed in APPENDIX-B. API Call Process The application selects an API by setting the 4 variables available when the flash_api library is linked to the application. These four variables are located in RAM at fixed address: * * * * api_command: 1Ch api_value: 1Dh api_dph: 1Eh api_dpl: 1Fh All calls are made through a common interface "USER_CALL" at the address FFC0h. The jump at the USER_CALL must be done by LCALL instruction to be able to comeback in the application. Before jump at the USER_CALL, the bit ENBOOT in AUXR1 register must be set. Constraints The interrupts are not disabled by the bootloader. Interrupts must be disabled by user prior to jump to the USER_CALL, then re-enabled when returning. Interrupts must also be disabled before accessing EEPROM data then re-enabled after. The user must take care of hardware watchdog before launching a Flash operation. For more information regarding the Flash writing time see the AT89C5131A datasheet. 25 4287E-USB-04/08 API Commands Several types of APIs are available: * * * * * Read/Program Flash and EEPROM Data Memory Read Configuration and Manufacturer Information Program Configuration Information Erase Flash Start Bootloader Read/Program Flash and EEPROM Data Memory All routines to access EEPROM data are managed directly from the application without using bootloader resources. To read the Flash memory the bootloader is not involved. For more details on these routines see the AT89C5131A datasheet sections "Program/Code Memory" and "EEPROM Data Memory" Two routines are available to program the Flash: - - * __api_wr_code_byte __api_wr_code_page The application program load the column latches of the Flash then calls the __api_wr_code_byte or __api_wr_code_page see datasheet in section "Program/Code Memory". Parameter settings API Name __api_wr_code_byte __api_wr_code_page * api_command 0Dh api_dph api_dpl api_value * instruction: LCALL FFC0h. No special resources are used by the bootloader during this operation Note: 26 AT89C5131A USB Bootloader 4287E-USB-04/08 AT89C5131A USB Bootloader Read Configuration and Manufacturer Information * Parameter settings API Name __api_rd_HSB __api_rd_BSB __api_rd_SBV __api_rd_P1_CF __api_rd_P3_CF __api_rd_P4_CF __api_rd_SSB __api_rd_EB __api_rd_manufacturer __api_rd_device_id1 __api_rd_device_id2 __api_rd_device_id3 __api_rd_bootloader_version api_command 08h 05h 05h 05h 05h 05h 05h 05h 05h 05h 05h 05h 0Eh api_dph api_dpl 00h 00h 01h 02h 03h 04h 05h 06h 30h 31h 60h 61h 00h api_value return HSB return BSB return SBV return P1_CF return P3_CF return P4_CF return SSB return EB return manufacturer id return id1 return id2 return id3 return value * * Instruction: LCALL FFC0h. At the complete API execution by the bootloader, the value to read is in the api_value variable. No special resources are used by the bootloader during this operation Note: 27 4287E-USB-04/08 Program Configuration Information * Parameter settings API Name __api_clr_BLJB __api_set_BLJB __api_clr_X2 __api_set_X2 __api_clr_OSCON1 __api_set_OSCON1 __api_clr_OSCON0 __api_set_OSCON0 __api_wr_BSB __api_wr_SBV __api_wr_P1_CF __api_wr_P3_CF __api_wr_P4_CF __api_wr_SSB __api_wr_EB api_command 07h 07h 07h 07h 07h 07h 07h 07h 04h 04h 04h 04h 04h 04h 04h api_dph api_dpl api_value (HSB & BFh) | 40h HSB & BFh (HSB & 7Fh) | 80h HSB & 7Fh (HSB & DFh) | 20h HSB & DFh (HSB & EFh) | 10h HSB & EFh 00h 01h 02h 03h 04h 05h 06h value to write value to write value to write value to write value to write value to write value to write * instruction: LCALL FFC0h. 1. See in the T89C51CC01 datasheet the time that a write operation takes. 2. No special resources are used by the bootloader during these operations. Notes: Erasing the Flash The AT89C5131A Flash memory is divided in several blocks: Block 0: from address 0000h to 1FFFh Block 1: from address 2000h to 3FFFh Block 2: from address 4000h to 7FFFh These three blocks contain 128 pages. * Parameter settings API Name __api_erase_block0 __api_erase_block1 __api_erase_block2 api_command 00h 00h 00h api_dph 00h 20h 40h api_dpl api_value * instruction: LCALL FFC0h. 1. See the AT89C5131A datasheet for the time that a write operation takes and this time must multiply by the number of pages. 2. No special resources are used by the bootloader during these operations. Notes: 28 AT89C5131A USB Bootloader 4287E-USB-04/08 AT89C5131A USB Bootloader Starting the Bootloader This routine allows to start at the beginning of the bootloader as after a reset. After calling this routine the regular boot process is performed and the communication must be opened before any action. * * * No special parameter setting Set bit ENBOOT in AUXR1 register instruction: LJUMP or LCALL at address F400h 29 4287E-USB-04/08 Appendix-A Table 10. Summary of Frames from Host Command Identifier Id_prog_start 01h data[0] 00h data[1] data[2] data[3] data[4] Description Init FLASH programming start_address 01h 00h end_address Init EEPROM programming Display FLASH Data Id_display_data 03h 01h 02h start_address end_address Blank Check in FLASH Display EEPROM Data 00h 20h 00h 40h FFh 00h 01h Id_write_command 04h 01h 02h 03h 04h 05h 06h 02h 03h 01h address 00h 00h Value Value Erase block0 (0K to 8K) Erase block1 (8K to 16K) Erase block2 (16K to 32K) Full chip Erase (bits at FFh) Write value in BSB Write value in SBV Write P1_CF Write P3_CF Write P4_CF Write value in SSB Write value in EB Write value in Fuse (HSB) Hardware reset LJMP address 30 AT89C5131A USB Bootloader 4287E-USB-04/08 AT89C5131A USB Bootloader Table 10. Summary of Frames from Host (Continued) Command Identifier data[0] data[1] 00h 00h 01h 02h 00h 01h 02h 03h Id_read_command 05h 01h 04h 05h 06h 30h 31h 60h 61h 02h 00h data[2] data[3] data[4] Description Read Bootloader Version Read Device boot ID1 Read Device boot ID2 Read BSB Read SBV Read P1_CF Read P3_CF Read P4_CF Read SSB Read EB Read Manufacturer Code Read Family Code Read Product Name Read Product Revision Read HWB Table 11. DFU Class-specific Requests bmRequestType 0010 0001b 0010 0001b 1010 0001b 1010 0001b 0010 0001b 1010 0001b 0010 0001b bRequest DFU_DETACH (0) DFU_DNLOAD (1) DFU_UPLOAD (2) DFU_GETSTATUS (3) DFU_CLRSTATUS (4) DFU_GETSTATE (5) DFU_ABORT (6) wValue wTimeout wBlock wBlock Zero Zero Zero Zero wIndex Interface (4) Interface (4) Interface (4) Interface (4) Interface (4) Interface (4) Interface (4) wLength Zero Length Length 6 Zero 1 Zero Data none Firmware Firmware Status none State none Table 12. USB Parameters Parameter Vendor ID Product ID Release Number Atmel 0x03EB 0x2FFD 0x0000 Table 13. Hardware Security Byte (HSB) 7 X2 6 BLJB 5 OSCON1 4 OSCON0 3 2 LB2 1 LB1 0 LB0 31 4287E-USB-04/08 Appendix-2 Table 14. API Summary Function Name __api_rd_code_byte __api_wr_code_byte __api_wr_code_page __api_erase block0 __api_erase block1 __api_erase block2 __api_rd_HSB __api_clr_BLJB __api_set_BLJB __api_clr_X2 __api_set_X2 __api_clr_OSCON1 __api_set_OSCON1 __api_clr_OSCON0 __api_set_OSCON0 __api_rd_BSB __api_wr_BSB __api_rd_SBV __api_wr_SBV __api_erase_SBV __api_rd_P1_CF __api_wr_P1_CF __api_rd_P3_CF __api_wr_P3_CF __api_rd_P4_CF __api_wr_P4_CF __api_rd_SSB __api_wr_SSB __api_rd_EB __api_wr_EB __api_rd_manufacturer __api_rd_device_id1 Bootloader Execution no yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes api_command api_dph api_dpl api_value 0Dh 0Dh 00h 00h 00h 08h 07h 07h 07h 07h 07h 07h 07h 07h 05h 04h 05h 04h 04h 05h 04h 05h 04h 05h 04h 05h 04h 05h 04h 05h 05h 00h 00h 01h 01h 01h 02h 02h 03h 03h 04h 04h 05h 05h 06h 06h 30h 31h 00h 20h 40h 00h return value (HSB & BFh) | 40h HSB & BFh (HSB & 7Fh) | 80h HSB & 7Fh (HSB & DFh) | 20h HSB & DFh (HSB & EFh) | 10h HSB & EFh return value value return value value FFh return value value return value value return value value return value value return value value return value return value 32 AT89C5131A USB Bootloader 4287E-USB-04/08 AT89C5131A USB Bootloader Table 14. API Summary (Continued) Function Name __api_wr_code_page __api_rd_device_id2 __api_rd_device_id3 __api_rd_bootloader_version __api_eeprom_busy __api_rd_eeprom_byte __api_wr_eeprom_byte __api_start_bootloader __api_start_isp Bootloader Execution yes yes yes yes no no no no no api_command 01h 05h 05h 0Eh api_dph api_dpl api_value 60h 61h 00h return value return value return value 33 4287E-USB-04/08 Headquarters Atmel Corporation 2325 Orchard Parkway San Jose, CA 95131 USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 International Atmel Asia Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimshatsui East Kowloon Hong Kong Tel: (852) 2721-9778 Fax: (852) 2722-1369 Atmel Europe Le Krebs 8, Rue Jean-Pierre Timbaud BP 309 78054 Saint-Quentin-enYvelines Cedex France Tel: (33) 1-30-60-70-00 Fax: (33) 1-30-60-71-11 Atmel Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 Product Contact Web Site www.atmel.com Technical Support 8051@atmel.com Sales Contact www.atmel.com/contacts Literature Requests www.atmel.com/literature Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL'S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL'S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel's products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. (c) 2008 Atmel Corporation. All rights reserved. Atmel (R), logo and combinations thereof, and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. 4287E-USB-04/08 |
Price & Availability of AT89C5131A08 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |