 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| TEA1623P; TEA1623PH STARplug switched mode power supply controller IC Rev. 3 -- 30 August 2010 Product data sheet 1. General description The TEA1623 is a Switched Mode Power Supply (SMPS) controller IC that operates directly from rectified universal mains. It is implemented in the high voltage EZ-HV SOI process, combined with a low voltage BiCMOS process. The device includes a high voltage power switch and a circuit for start-up directly from the rectified mains voltage. A dedicated circuit for valley switching is built in, which makes a very efficient slim-line electronic power-plug concept possible. In its most basic version of application, the TEA1623 acts as a voltage source. Here, no additional secondary electronics are required. A combined voltage and current source can be realized with minimum costs for external components. Implementation of the TEA1623 renders an efficient and low cost power supply system. 2. Features and benefits Designed for general purpose power supplies Integrated power switch: 6.5 and 650 V Operates from universal AC mains supplies: 80 V to 276 V Adjustable frequency for flexible design RC oscillator for stable output regulation Valley switching for minimum switch-on loss Frequency reduction at low power output for low standby power: < 100 mW Adjustable OverCurrent Protection (OCP) UnderVoltage Protection (UVP) Temperature protection Short-winding protection Safe restart mode for system fault conditions Simple application with both primary and secondary (opto) feedback Available in 8-pin and 16-pin DIP packages. 3. Applications Adapters Set-Top Box (STB) DVD VCD CD(R) PC Silverbox standby SMPS NXP Semiconductors TEA1623P; TEA1623PH STARplug switched mode power supply controller IC 4. Quick reference data Table 1. Symbol VCC(max) VDRAIN(max) IDRAIN RDSon Quick reference data Parameter maximum supply voltage maximum DMOS power transistor drain voltage Tj > 0 C Conditions Min Typ 0.5 Max 40 650 Unit V V mA supply current drawn from no auxiliary supply pin DRAIN drain-source on-state resistance ISOURCE = -0.5 A Tj = 25 C Tj = 100 C 10 6.5 9.0 - 7.5 10.0 200 kHz fosc oscillator frequency range 5. Ordering information Table 2. Ordering information Package Name TEA1623P TEA1623PH DIP8 DIP16 Description plastic dual in-line package; 8 leads (300 mil) plastic dual in-line package; 16 leads (300 mil); long body Version SOT97-1 SOT38-1 Type number TEA1623P_TEA1623PH All information provided in this document is subject to legal disclaimers. (c) NXP B.V. 2010. All rights reserved. Product data sheet Rev. 3 -- 30 August 2010 2 of 20 NXP Semiconductors TEA1623P; TEA1623PH STARplug switched mode power supply controller IC 6. Block diagram VCC 1 SUPPLY 8 DRAIN VALLEY TEA1623P GND 2 LOGIC 100 mV 7 n.c. PWM stop RC 3 OSCILLATOR THERMAL SHUTDOWN PROTECTION LOGIC POWER-UP RESET 1.8 U 6 SOURCE low frequency f blank overcurrent REG 4 2.5 V 10x short winding 0.75 V 0.5 V 5 AUX col011 Fig 1. Block diagram of TEA1623P TEA1623P_TEA1623PH All information provided in this document is subject to legal disclaimers. (c) NXP B.V. 2010. All rights reserved. Product data sheet Rev. 3 -- 30 August 2010 3 of 20 NXP Semiconductors TEA1623P; TEA1623PH STARplug switched mode power supply controller IC VCC 3 SUPPLY 14 1, 2, 7, 9, 10, 13, 15, 16 DRAIN VALLEY TEA1623PH n.c. GND 4 LOGIC 100 mV PWM stop RC 5 OSCILLATOR THERMAL SHUTDOWN PROTECTION LOGIC POWER-UP RESET 1.8 U 12 SOURCE low frequency f blank overcurrent REG 6 2.5 V 10x short winding 0.5 V 11 AUX SGND 8 0.75 V col013 Fig 2. Block diagram of TEA1623PH 7. Pinning information 7.1 Pinning n.c. n.c. VCC GND VCC GND RC REG 1 2 3 4 001aaa310 1 2 3 4 5 6 7 8 001aaa312 16 n.c. 15 n.c. 14 DRAIN 8 DRAIN n.c. SOURCE AUX RC REG n.c. SGND TEA1623PH 13 n.c. 12 SOURCE 11 AUX 10 n.c. 9 n.c. TEA1623P 7 6 5 Fig 3. Pin configuration for SOT97-1 (DIP8) Fig 4. Pin configuration for SOT38-1 (DIP16) TEA1623P_TEA1623PH All information provided in this document is subject to legal disclaimers. (c) NXP B.V. 2010. All rights reserved. Product data sheet Rev. 3 -- 30 August 2010 4 of 20 NXP Semiconductors TEA1623P; TEA1623PH STARplug switched mode power supply controller IC 7.2 Pin description Table 3. Symbol VCC GND RC REG SGND AUX SOURCE n.c. DRAIN Pin description Pin TEA1623P 1 2 3 4 5 6 7 8 TEA1623PH 3 4 5 6 8 11 12 1, 2, 7, 9, 10, 13, 15, 16 14 supply voltage ground frequency setting regulation point signal ground; preferably connected to pin GND input for voltage from auxiliary winding for timing (demagnetization) source of internal MOS switch not connected drain of internal MOS switch; input for start-up current and valley sensing Description 8. Functional description The TEA1623 is the heart of a compact flyback converter, with the IC placed at the primary side. The auxiliary winding of the transformer can be used for indirect feedback to control the isolated output. This additional winding also powers the IC. A more accurate control of the output voltage and/or current can be implemented with an additional secondary sensing circuit and optocoupler feedback. The TEA1623 uses voltage mode control. The frequency is determined by the maximum transformer demagnetizing time or the frequency of the oscillator. In the first case, the converter operates in the Self Oscillating Power Supply (SOPS) mode. In the latter case, it operates at a constant frequency, which can be adjusted with external components RRC and CRC. This mode is called Pulse Width Modulation (PWM). Furthermore, a primary stroke is started only in a valley of the secondary ringing. This valley switching principle minimizes capacitive switch-on losses. 8.1 Start-up and UnderVoltage LockOut (UVLO) Initially, the IC is self supplying from the rectified mains voltage. The IC starts switching as soon as the voltage on pin VCC passes the VCC(start) level. The supply is taken over by the auxiliary winding of the transformer as soon as VCC is high enough and the supply from the line is stopped for high efficiency operation. As soon as the voltage on pin VCC drops below the VCC(stop) level, the IC stops switching and restarts from the rectified mains voltage. 8.2 Oscillator The frequency of the oscillator is set by the external resistor and capacitor on pin RC. The external capacitor is charged rapidly to the VRC(max) level and, starting from a new primary stroke, it discharges to the VRC(min) level. Because the discharge is exponential, the TEA1623P_TEA1623PH All information provided in this document is subject to legal disclaimers. (c) NXP B.V. 2010. All rights reserved. Product data sheet Rev. 3 -- 30 August 2010 5 of 20 NXP Semiconductors TEA1623P; TEA1623PH STARplug switched mode power supply controller IC relative sensitivity of the duty factor to the regulation voltage at low duty factor is almost equal to the sensitivity at high duty factors. This results in a more constant gain over the duty factor range compared to PWM systems with a linear sawtooth oscillator. Stable operation at low duty factors is easily realized. For high efficiency, the frequency is reduced as soon as the duty factor drops below a certain value. This is accomplished by increasing the oscillator charge time. To ensure that the capacitor can be charged within the charge time, the value of the oscillator capacitor should be limited to approximately 1 nF. 8.3 Duty factor control The duty factor is controlled by the internal regulation voltage and the oscillator signal on pin RC. The internal regulation voltage is equal to the external regulation voltage (-2.5 V) multiplied by the gain of the error amplifier (typical 20 dB or 10x). The minimum duty factor of the switched mode power supply is 0 %. The maximum duty factor is set to 75 % (typical value at 100 kHz oscillation frequency). 8.4 Valley switching A new cycle is started at the primary stroke when the switch is switched on (see Figure 5). After a certain time (determined by the RC oscillator voltage and the internal regulation level), the switch is turned off and the secondary stroke starts. The internal regulation level is determined by the voltage on pin REG. After the secondary stroke, the drain 1 voltage shows an oscillation with a frequency of approximately ----------------------------- , where: 2 x L p C p Lp is the primary self inductance on the drain node. Cp is the parasitic capacitance on the drain node. As soon as the oscillator voltage is high again and the secondary stroke has ended, the circuit waits for a low drain voltage before starting a new primary stroke. The primary stroke starts some time before the actual valley at low ringing frequencies, and some time after the actual valley at high ringing frequencies. Figure 6 shows a typical curve for a reflected voltage N x Vo of 80 V. This voltage is the output voltage Vo (see Figure 7) transferred to the primary side of the transformer with the factor N (determined by the turns ratio of the transformer). Figure 6 shows that the system switches exactly at minimum drain voltage for ringing frequencies of 480 kHz, thus reducing the switch-on losses to a minimum. At 200 kHz, the next primary stroke is started at 33 before the valley. The switch-on losses are still reduced significantly. TEA1623P_TEA1623PH All information provided in this document is subject to legal disclaimers. (c) NXP B.V. 2010. All rights reserved. Product data sheet Rev. 3 -- 30 August 2010 6 of 20 NXP Semiconductors TEA1623P; TEA1623PH STARplug switched mode power supply controller IC primary stroke secondary stroke secondary ringing drain valley secondary stroke A RC oscillator regulation level B col007 A: Start of new cycle with valley switching. B: Start of new cycle in a classical PWM system. Fig 5. Signals for valley switching 40 phase () 20 001aaa311 0 -20 -40 0 200 400 600 f (kHz) 800 Reflected voltage at N x Vo = 80 V. Fig 6. Typical phase of drain ringing at switch-on 8.5 Demagnetization The system operates in discontinuous conduction mode all the time. As long as the secondary stroke has not ended, the oscillator will not start a new primary stroke. During the suppression time tsuppr, demagnetization recognition is suppressed. This suppression may be necessary in applications where the transformer has a large leakage inductance and at low output voltages. TEA1623P_TEA1623PH All information provided in this document is subject to legal disclaimers. (c) NXP B.V. 2010. All rights reserved. Product data sheet Rev. 3 -- 30 August 2010 7 of 20 NXP Semiconductors TEA1623P; TEA1623PH STARplug switched mode power supply controller IC 8.6 Protection 8.6.1 Overcurrent protection The cycle-by-cycle peak drain current limit circuit uses the external source resistor RI (see Figure 7) to measure the current. The circuit is activated after the leading edge blanking time tleb. The protection circuit limits the source voltage to Vsource(max), and thus limits the primary peak current. 8.6.2 Short-winding protection The short-winding protection circuit is also activated after the leading edge blanking time. If the source voltage exceeds the short-winding protection voltage Vswp, the TEA1623 stops switching. Only a power-on reset will restart normal operation. The short-winding protection also protects in case of a secondary diode short circuit. 8.6.3 OverTemperature Protection (OTP) An accurate temperature protection is provided in the TEA1623. When the junction temperature exceeds the thermal shut-down temperature, the IC stops switching. During thermal protection, the IC current is lowered to the start-up current. The IC continues normal operation as soon as the overtemperature situation has disappeared. 8.6.4 OverVoltage Protection (OVP) Overvoltage protection can be achieved in the application by pulling pin REG above its normal operation level, or by keeping the level of pin AUX above Vdemag. The current primary stroke is terminated immediately and no new primary stroke is started until the voltage on pin REG drops to its normal operation level. Pin REG has an internal clamp. The current feed into pin REG must be limited. 8.7 Characteristics of the complete power-plug 8.7.1 Input The input voltage range comprises the universal AC mains from 80 V to 276 V. 8.7.2 Accuracy The accuracy of the complete converter, functioning as a voltage source with primary sensing, is approximately 8 % (mainly dependent on the transformer coupling). The accuracy with secondary sensing is defined by the accuracy of the external components. For safety requirements in case of optocoupler feedback loss, the primary sensing remains active when an overvoltage circuit is connected. 8.7.3 Efficiency An efficiency of 75 % at maximum output power can be achieved for a complete converter designed for universal mains. 8.7.4 Ripple A minimum ripple is obtained in a system designed for a maximum duty factor of 50 % under normal operating conditions and a minimized dead time. The magnitude of the ripple in the output voltage is determined by the frequency and duty factor of the converter, the output current level, and the value and ESR of the output capacitor. TEA1623P_TEA1623PH All information provided in this document is subject to legal disclaimers. (c) NXP B.V. 2010. All rights reserved. Product data sheet Rev. 3 -- 30 August 2010 8 of 20 NXP Semiconductors TEA1623P; TEA1623PH STARplug switched mode power supply controller IC 9. Limiting values Table 4. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Symbol Voltage VCC VRC VSOURCE VDRAIN Current IREG IAUX IRC ISOURCE IDRAIN General Ptot total power dissipation TEA1623P; Tamb < 45 C TEA1623PH; Tamb < 50 C Tstg Tj VESD storage temperature junction temperature electrostatic discharge voltage human body pin DRAIN all other pins machine model[4] all pins [1] [2] [3] [4] Pins VCC and RC are not allowed to be current driven. Pins REG and AUX are not allowed to be voltage driven. Human body model: equivalent to discharging a 100 pF capacitor through a 1.5 k series resistor. Machine model: equivalent to discharging a 200 pF capacitor through a 0.75 H coil and a 10 series resistor. Parameter supply voltage oscillator input voltage DMOS power transistor source voltage DMOS power transistor drain voltage regulation input current auxiliary winding input current oscillator capacitor charge current source current drain current Conditions continuous [1] [1] Min -0.4 -0.4 -0.4 Max +40 +3 +5 +650 Unit V V V V Tj > 0 C -0.4 [2] [2] -10 -3 -2 -2 6 +5 +2 +2 mA mA mA A A -55 -20 1.0 1.7 +150 +145 +1500 +2000 +200 W W C C V V V model[3] -1500 -2000 -200 10. Thermal characteristics Table 5. Symbol Rth(j-a) Thermal characteristics Parameter thermal resistance from junction to ambient Conditions in free air TEA1623P TEA1623PH [1] [1] Typ 100 55 Unit K/W K/W Thermal resistance Rth(j-a) can be lower when pin GND is connected to sufficient copper area on the printed-circuit board. See the TEA152x application note for details. TEA1623P_TEA1623PH All information provided in this document is subject to legal disclaimers. (c) NXP B.V. 2010. All rights reserved. Product data sheet Rev. 3 -- 30 August 2010 9 of 20 NXP Semiconductors TEA1623P; TEA1623PH STARplug switched mode power supply controller IC 11. Characteristics Table 6. Characteristics Tamb = 25 C; no overtemperature; all voltages are measured with respect to ground; currents are positive when flowing into the IC, unless otherwise specified. Symbol Supplies Supply on pin VCC VCC(start) VCC(stop) ICC(operate) ICC(startup) ICC(ch) start voltage stop voltage operating supply current start-up supply current charging current undervoltage lockout normal operation start-up VDRAIN > 60 V VCC = 0 V VCC = 8.5 V Supply on pin DRAIN IDRAIN PWM mode min max Vdemag tsuppr minimum duty factor maximum duty factor demagnetization recognition voltage level time of suppression of transformer ringing at start of secondary stroke minimum voltage of RC oscillator setting maximum voltage of RC oscillator setting RC charging time oscillator frequency range input voltage on pin REG voltage gain of error amplifier clamping voltage on pin REG valley recognition ringing frequency for valley switching delay from valley recognition to switch-on drain leakage current VDRAIN = 650 V All information provided in this document is subject to legal disclaimers. Parameter Conditions Min Typ Max Unit 9 7.0 -650 -375 fosc = 100 kHz 50 1.0 9.5 7.5 1.3 180 -520 -275 0.5 30 0 75 100 1.5 10 8.0 1.9 400 -390 -175 125 150 2.0 V V mA A A A mA A % % mV s supply current drawn from pin DRAIN no auxiliary supply with auxiliary supply; VDRAIN > 60 V Self-oscillating power supply mode Oscillator: pin RC VRC(min) VRC(max) tRC(ch) fosc VREG GV(erroramp) VREG(clamp) dV/dtvalley fvalley td(valley-on) 60 2.4 10 2.4 IREG = 6 mA -102 N x Vo = 100 V 200 75 2.5 1 2.5 20 550 150 90 2.6 200 2.6 7.5 +102 800 mV V s kHz V dB V V/s kHz ns Duty factor regulator: pin REG Valley switching recognition Output stage (FET) IL(drain) TEA1623P_TEA1623PH - - 125 A (c) NXP B.V. 2010. All rights reserved. Product data sheet Rev. 3 -- 30 August 2010 10 of 20 NXP Semiconductors TEA1623P; TEA1623PH STARplug switched mode power supply controller IC Table 6. Characteristics ...continued Tamb = 25 C; no overtemperature; all voltages are measured with respect to ground; currents are positive when flowing into the IC, unless otherwise specified. Symbol VBR(drain) RDSon Parameter drain breakdown voltage drain-source on-state resistance Conditions Tj > 0 C ISOURCE = -0.5 A Tj = 25 C Tj = 100 C tdrain(f) drain fall time VDRAIN(switch_on) = 300 V; no external capacitor at pin DRAIN 6.5 9.0 75 7.5 10.0 ns Min 650 Typ Max Unit V Temperature protection Tprot(max) Tprot(hys) Vsource(max) Vswp td(propagation) tleb maximum threshold temperature threshold temperature hysteresis overcurrent protection voltage short-winding protection voltage dV/dt = 0.1 V/s dV/dt = 0.5 V/s 150 0.47 0.7 250 160 2 0.50 0.75 160 350 170 0.53 0.8 185 450 C C V V ns ns Overcurrent and short winding protection: pin SOURCE delay from detecting Vsource(max) to dV/dt = 0.5 V/s switch-off leading edge blanking time overcurrent and short-winding protection 12. Application information LF Z1 CF1 mains R1 R2 D2 CF2 D1 D5 C5 Vo CVCC VCC GND 1 2 3 4 8 7 6 5 DRAIN n.c. SOURCE AUX RI RAUX C6 - Ycap RRC RC R4 CRC R3 REG TEA1623P col012 Further application information can be found in the TEA152x application note. Fig 7. Application with primary sensing for TEA1623P TEA1623P_TEA1623PH All information provided in this document is subject to legal disclaimers. (c) NXP B.V. 2010. All rights reserved. Product data sheet Rev. 3 -- 30 August 2010 11 of 20 NXP Semiconductors TEA1623P; TEA1623PH STARplug switched mode power supply controller IC 13. Package outline DIP8: plastic dual in-line package; 8 leads (300 mil) SOT97-1 D seating plane ME A2 A L A1 c Z e b1 wM (e 1) b2 5 MH b 8 pin 1 index E 1 4 0 5 scale 10 mm DIMENSIONS (inch dimensions are derived from the original mm dimensions) UNIT mm inches A max. 4.2 0.17 A1 min. 0.51 0.02 A2 max. 3.2 0.13 b 1.73 1.14 0.068 0.045 b1 0.53 0.38 0.021 0.015 b2 1.07 0.89 0.042 0.035 c 0.36 0.23 0.014 0.009 D (1) 9.8 9.2 0.39 0.36 E (1) 6.48 6.20 0.26 0.24 e 2.54 0.1 e1 7.62 0.3 L 3.60 3.05 0.14 0.12 ME 8.25 7.80 0.32 0.31 MH 10.0 8.3 0.39 0.33 w 0.254 0.01 Z (1) max. 1.15 0.045 Note 1. Plastic or metal protrusions of 0.25 mm (0.01 inch) maximum per side are not included. OUTLINE VERSION SOT97-1 REFERENCES IEC 050G01 JEDEC MO-001 JEITA SC-504-8 EUROPEAN PROJECTION ISSUE DATE 99-12-27 03-02-13 Fig 8. Package outline SOT97-1 (DIP8) All information provided in this document is subject to legal disclaimers. (c) NXP B.V. 2010. All rights reserved. TEA1623P_TEA1623PH Product data sheet Rev. 3 -- 30 August 2010 12 of 20 NXP Semiconductors TEA1623P; TEA1623PH STARplug switched mode power supply controller IC DIP16: plastic dual in-line package; 16 leads (300 mil); long body SOT38-1 D seating plane ME A2 A L A1 c Z e b1 b 16 9 MH wM (e 1) pin 1 index E 1 8 0 5 scale 10 mm DIMENSIONS (inch dimensions are derived from the original mm dimensions) UNIT mm inches A max. 4.7 0.19 A1 min. 0.51 0.02 A2 max. 3.7 0.15 b 1.40 1.14 0.055 0.045 b1 0.53 0.38 0.021 0.015 c 0.32 0.23 0.013 0.009 D (1) 21.8 21.4 0.86 0.84 E (1) 6.48 6.20 0.26 0.24 e 2.54 0.1 e1 7.62 0.3 L 3.9 3.4 0.15 0.13 ME 8.25 7.80 0.32 0.31 MH 9.5 8.3 0.37 0.33 w 0.254 0.01 Z (1) max. 2.2 0.087 Note 1. Plastic or metal protrusions of 0.25 mm (0.01 inch) maximum per side are not included. OUTLINE VERSION SOT38-1 REFERENCES IEC 050G09 JEDEC MO-001 JEITA SC-503-16 EUROPEAN PROJECTION ISSUE DATE 99-12-27 03-02-13 Fig 9. Package outline SOT38-1 (DIP16) All information provided in this document is subject to legal disclaimers. (c) NXP B.V. 2010. All rights reserved. TEA1623P_TEA1623PH Product data sheet Rev. 3 -- 30 August 2010 13 of 20 NXP Semiconductors TEA1623P; TEA1623PH STARplug switched mode power supply controller IC 14. Soldering of through-hole mount packages 14.1 Introduction to soldering through-hole mount packages This text gives a very brief insight into wave, dip and manual soldering. Wave soldering is the preferred method for mounting of through-hole mount IC packages on a printed-circuit board. 14.2 Soldering by dipping or by solder wave Driven by legislation and environmental forces the worldwide use of lead-free solder pastes is increasing. Typical dwell time of the leads in the wave ranges from 3 seconds to 4 seconds at 250 C or 265 C, depending on solder material applied, SnPb or Pb-free respectively. The total contact time of successive solder waves must not exceed 5 seconds. The device may be mounted up to the seating plane, but the temperature of the plastic body must not exceed the specified maximum storage temperature (Tstg(max)). If the printed-circuit board has been pre-heated, forced cooling may be necessary immediately after soldering to keep the temperature within the permissible limit. 14.3 Manual soldering Apply the soldering iron (24 V or less) to the lead(s) of the package, either below the seating plane or not more than 2 mm above it. If the temperature of the soldering iron bit is less than 300 C it may remain in contact for up to 10 seconds. If the bit temperature is between 300 C and 400 C, contact may be up to 5 seconds. 14.4 Package related soldering information Table 7. Package CPGA, HCPGA DBS, DIP, HDIP, RDBS, SDIP, SIL PMFP[2] [1] [2] Suitability of through-hole mount IC packages for dipping and wave soldering Soldering method Dipping suitable Wave suitable suitable[1] not suitable For SDIP packages, the longitudinal axis must be parallel to the transport direction of the printed-circuit board. For PMFP packages hot bar soldering or manual soldering is suitable. TEA1623P_TEA1623PH All information provided in this document is subject to legal disclaimers. (c) NXP B.V. 2010. All rights reserved. Product data sheet Rev. 3 -- 30 August 2010 14 of 20 NXP Semiconductors TEA1623P; TEA1623PH STARplug switched mode power supply controller IC 15. Abbreviations Table 8. Acronym BiCMOS CMOS DMOS ESR OCP OTP OVP PWM SMPS SOI SOPS STB UVLO UVP VCD Abbreviations Description Bipolar CMOS Complementary Metal-Oxide Semiconductor Diffusion Metal-Oxide Semiconductor Equivalent Series Resistance OverCurrent Protection OverTemperature Protection OverVoltage Protection Pulse Width Modulation Switched Mode Power Supply Silicon On Insulator Self Oscillating Power Supply Set-Top Box UnderVoltage LockOut UnderVoltage Protection Video Compact Disc 16. Revision history Table 9. Revision history Release date 20100830 Data sheet status Product data sheet Change notice Supersedes TEA1623P_TEA1623PH_2 Document ID TEA1623P_TEA1623PH v.3 Modifications: TEA1623P_TEA1623PH_2 Modifications: * * * * * * Table 1 "Quick reference data" updated. Table 4 "Limiting values" updated. Product data sheet TEA1623P_TEA1623PH_1 The format of this data sheet has been redesigned to comply with the new identity guidelines of NXP Semiconductors. Legal texts have been adapted to the new company name where appropriate. Pin configuration drawing A and B split into Figure 3 "Pin configuration for SOT97-1 (DIP8)" and Figure 4 "Pin configuration for SOT38-1 (DIP16)". Section 15 "Abbreviations" added. Product data sheet - 20091104 TEA1623P_TEA1623PH_1 20040317 TEA1623P_TEA1623PH All information provided in this document is subject to legal disclaimers. (c) NXP B.V. 2010. All rights reserved. Product data sheet Rev. 3 -- 30 August 2010 15 of 20 NXP Semiconductors TEA1623P; TEA1623PH STARplug switched mode power supply controller IC 17. Legal information 17.1 Data sheet status Document status[1][2] Objective [short] data sheet Preliminary [short] data sheet Product [short] data sheet [1] [2] [3] Product status[3] Development Qualification Production Definition This document contains data from the objective specification for product development. This document contains data from the preliminary specification. This document contains the product specification. Please consult the most recently issued document before initiating or completing a design. The term `short data sheet' is explained in section "Definitions". The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com. 17.2 Definitions Draft -- The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet -- A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. Product specification -- The information and data provided in a Product data sheet shall define the specification of the product as agreed between NXP Semiconductors and its customer, unless NXP Semiconductors and customer have explicitly agreed otherwise in writing. In no event however, shall an agreement be valid in which the NXP Semiconductors product is deemed to offer functions and qualities beyond those described in the Product data sheet. malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors accepts no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer's own risk. Applications -- Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Customers are responsible for the design and operation of their applications and products using NXP Semiconductors products, and NXP Semiconductors accepts no liability for any assistance with applications or customer product design. It is customer's sole responsibility to determine whether the NXP Semiconductors product is suitable and fit for the customer's applications and products planned, as well as for the planned application and use of customer's third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. NXP Semiconductors does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer's applications or products, or the application or use by customer's third party customer(s). Customer is responsible for doing all necessary testing for the customer's applications and products using NXP Semiconductors products in order to avoid a default of the applications and the products or of the application or use by customer's third party customer(s). NXP does not accept any liability in this respect. Limiting values -- Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the device. Limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the Recommended operating conditions section (if present) or the Characteristics sections of this document is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. Terms and conditions of commercial sale -- NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, unless otherwise agreed in a valid written individual agreement. In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. NXP Semiconductors hereby expressly objects to applying the customer's general terms and conditions with regard to the purchase of NXP Semiconductors products by customer. No offer to sell or license -- Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. Export control -- This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from national authorities. (c) NXP B.V. 2010. All rights reserved. 17.3 Disclaimers Limited warranty and liability -- Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. In no event shall NXP Semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Notwithstanding any damages that customer might incur for any reason whatsoever, NXP Semiconductors' aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of NXP Semiconductors. Right to make changes -- NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use -- NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or TEA1623P_TEA1623PH All information provided in this document is subject to legal disclaimers. Product data sheet Rev. 3 -- 30 August 2010 16 of 20 NXP Semiconductors TEA1623P; TEA1623PH STARplug switched mode power supply controller IC product for such automotive applications, use and specifications, and (b) whenever customer uses the product for automotive applications beyond NXP Semiconductors' specifications such use shall be solely at customer's own risk, and (c) customer fully indemnifies NXP Semiconductors for any liability, damages or failed product claims resulting from customer design and use of the product for automotive applications beyond NXP Semiconductors' standard warranty and NXP Semiconductors' product specifications. Quick reference data -- The Quick reference data is an extract of the product data given in the Limiting values and Characteristics sections of this document, and as such is not complete, exhaustive or legally binding. Non-automotive qualified products -- Unless this data sheet expressly states that this specific NXP Semiconductors product is automotive qualified, the product is not suitable for automotive use. It is neither qualified nor tested in accordance with automotive testing or application requirements. NXP Semiconductors accepts no liability for inclusion and/or use of non-automotive qualified products in automotive equipment or applications. In the event that customer uses the product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall use the product without NXP Semiconductors' warranty of the 17.4 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. 18. Contact information For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com TEA1623P_TEA1623PH All information provided in this document is subject to legal disclaimers. (c) NXP B.V. 2010. All rights reserved. Product data sheet Rev. 3 -- 30 August 2010 17 of 20 NXP Semiconductors TEA1623P; TEA1623PH STARplug switched mode power supply controller IC 19. Tables Table 1. Table 2. Table 3. Table 4. Table 5. Table 6. Table 7. Table 8. Table 9. Quick reference data . . . . . . . . . . . . . . . . . . . . .2 Ordering information . . . . . . . . . . . . . . . . . . . . .2 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . .5 Limiting values . . . . . . . . . . . . . . . . . . . . . . . . . .9 Thermal characteristics . . . . . . . . . . . . . . . . . . .9 Characteristics . . . . . . . . . . . . . . . . . . . . . . . . .10 Suitability of through-hole mount IC packages for dipping and wave soldering . . . .14 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . .15 Revision history . . . . . . . . . . . . . . . . . . . . . . . .15 continued >> TEA1623P_TEA1623PH All information provided in this document is subject to legal disclaimers. (c) NXP B.V. 2010. All rights reserved. Product data sheet Rev. 3 -- 30 August 2010 18 of 20 NXP Semiconductors TEA1623P; TEA1623PH STARplug switched mode power supply controller IC 20. Figures Fig 1. Fig 2. Fig 3. Fig 4. Fig 5. Fig 6. Fig 7. Fig 8. Fig 9. Block diagram of TEA1623P . . . . . . . . . . . . . . . . .3 Block diagram of TEA1623PH . . . . . . . . . . . . . . . .4 Pin configuration for SOT97-1 (DIP8) . . . . . . . . . .4 Pin configuration for SOT38-1 (DIP16) . . . . . . . . .4 Signals for valley switching . . . . . . . . . . . . . . . . . .7 Typical phase of drain ringing at switch-on . . . . . .7 Application with primary sensing for TEA1623P . 11 Package outline SOT97-1 (DIP8) . . . . . . . . . . . .12 Package outline SOT38-1 (DIP16) . . . . . . . . . . .13 continued >> TEA1623P_TEA1623PH All information provided in this document is subject to legal disclaimers. (c) NXP B.V. 2010. All rights reserved. Product data sheet Rev. 3 -- 30 August 2010 19 of 20 NXP Semiconductors TEA1623P; TEA1623PH STARplug switched mode power supply controller IC 21. Contents 1 2 3 4 5 6 7 7.1 7.2 8 8.1 8.2 8.3 8.4 8.5 8.6 8.6.1 8.6.2 8.6.3 8.6.4 8.7 8.7.1 8.7.2 8.7.3 8.7.4 9 10 11 12 13 14 14.1 14.2 14.3 14.4 15 16 17 17.1 17.2 17.3 17.4 18 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features and benefits . . . . . . . . . . . . . . . . . . . . 1 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Quick reference data . . . . . . . . . . . . . . . . . . . . . 2 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pinning information . . . . . . . . . . . . . . . . . . . . . . 4 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 5 Functional description . . . . . . . . . . . . . . . . . . . 5 Start-up and UnderVoltage LockOut (UVLO) . . 5 Oscillator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Duty factor control . . . . . . . . . . . . . . . . . . . . . . 6 Valley switching . . . . . . . . . . . . . . . . . . . . . . . . 6 Demagnetization. . . . . . . . . . . . . . . . . . . . . . . . 7 Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Overcurrent protection . . . . . . . . . . . . . . . . . . . 8 Short-winding protection . . . . . . . . . . . . . . . . . . 8 OverTemperature Protection (OTP) . . . . . . . . . 8 OverVoltage Protection (OVP) . . . . . . . . . . . . . 8 Characteristics of the complete power-plug . . . 8 Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Accuracy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Efficiency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Ripple . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 9 Thermal characteristics . . . . . . . . . . . . . . . . . . 9 Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . 10 Application information. . . . . . . . . . . . . . . . . . 11 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 12 Soldering of through-hole mount packages . 14 Introduction to soldering through-hole mount packages . . . . . . . . . . . . . . . . . . . . . . . 14 Soldering by dipping or by solder wave . . . . . 14 Manual soldering . . . . . . . . . . . . . . . . . . . . . . 14 Package related soldering information . . . . . . 14 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 15 Legal information. . . . . . . . . . . . . . . . . . . . . . . 16 Data sheet status . . . . . . . . . . . . . . . . . . . . . . 16 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Contact information. . . . . . . . . . . . . . . . . . . . . 17 19 20 21 Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section `Legal information'. (c) NXP B.V. 2010. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Date of release: 30 August 2010 Document identifier: TEA1623P_TEA1623PH |
Price & Availability of TEA1623P
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |