|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
Freescale Semiconductor Data Sheet: Product Preview Document Number: K60P144M100SF2 Rev. 4, 3/2011 Supports the following: MK60N256VLQ100, MK60X256VLQ100, MK60N512VLQ100, MK60N256VMD100, MK60X256VMD100, MK60N512VMD100 K60 Sub-Family Data Sheet K60P144M100SF2 Features * Operating Characteristics - Voltage range: 1.71 to 3.6 V - Flash write voltage range: 1.71 to 3.6 V - Temperature range (ambient): -40 to 105C * Performance - Up to 100 MHz ARM Cortex-M4 core with DSP instructions delivering 1.25 Dhrystone MIPS per MHz * Memories and memory interfaces - Up to 512 KB program flash memory on nonFlexMemory devices - Up to 256 KB program flash memory on FlexMemory devices - Up to 256 KB FlexNVM on FlexMemory devices - 4 KB FlexRAM on FlexMemory devices - Up to 128 KB RAM - Serial programming interface (EzPort) - FlexBus external bus interface * Clocks - 3 to 32 MHz crystal oscillator - 32 kHz crystal oscillator - Multi-purpose clock generator * System peripherals - 10 low-power modes to provide power optimization based on application requirements - Memory protection unit with multi-master protection - 16-channel DMA controller, supporting up to 64 request sources - External watchdog monitor - Software watchdog - Low-leakage wakeup unit * Security and integrity modules - Hardware CRC module to support fast cyclic redundancy checks - Hardware random-number generator - Hardware encryption supporting DES, 3DES, AES, MD5, SHA-1, and SHA-256 algorithms - 128-bit unique identification (ID) number per chip * Human-machine interface - Low-power hardware touch sensor interface (TSI) - General-purpose input/output * Analog modules - Two 16-bit SAR ADCs - Programmable gain amplifier (up to x64) integrated into each ADC - Two 12-bit DACs - Three analog comparators (CMP) containing a 6-bit DAC and programmable reference input - Voltage reference * Timers - Programmable delay block - Eight-channel motor control/general purpose/PWM timer - Two 2-channel quadrature decoder/general purpose timers - IEEE 1588 timers - Periodic interrupt timers - 16-bit low-power timer - Carrier modulator transmitter - Real-time clock This document contains information on a product under development. Freescale reserves the right to change or discontinue this product without notice. (c) 2010-2011 Freescale Semiconductor, Inc. Preliminary * Communication interfaces - Ethernet controller with MII and RMII interface to external PHY and hardware IEEE 1588 capability - USB full-/low-speed On-the-Go controller with on-chip transceiver - Two Controller Area Network (CAN) modules - Three SPI modules - Two I2C modules - Five UART modules - Secure Digital host controller (SDHC) - I2S module K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. 2 Preliminary Freescale Semiconductor, Inc. Table of Contents 1 Ordering parts...........................................................................5 1.1 Determining valid orderable parts......................................5 2 Part identification......................................................................5 2.1 Description.........................................................................5 2.2 Format...............................................................................5 2.3 Fields.................................................................................5 2.4 Example............................................................................6 3 Terminology and guidelines......................................................6 3.1 Definition: Operating requirement......................................6 3.2 Definition: Operating behavior...........................................7 3.3 Definition: Attribute............................................................7 3.4 Definition: Rating...............................................................8 3.5 Result of exceeding a rating..............................................8 3.6 Relationship between ratings and operating requirements......................................................................8 3.7 Guidelines for ratings and operating requirements............9 3.8 Definition: Typical value.....................................................9 3.9 Typical value conditions....................................................10 4 Ratings......................................................................................10 4.1 Thermal handling ratings...................................................11 4.2 Moisture handling ratings..................................................11 4.3 ESD handling ratings.........................................................11 4.4 Voltage and current operating ratings...............................11 5 General.....................................................................................12 5.1 Nonswitching electrical specifications...............................12 5.1.1 5.1.2 5.1.3 5.1.4 5.1.5 5.1.6 5.1.7 5.1.8 Voltage and current operating requirements......12 LVD and POR operating requirements...............13 Voltage and current operating behaviors............14 Power mode transition operating behaviors.......14 Power consumption operating behaviors............15 EMC radiated emissions operating behaviors....18 Designing with radiated emissions in mind.........19 Capacitance attributes........................................19 6.8.8 6.8.9 6.8.10 6.8.11 6.8.7 6 Peripheral operating requirements and behaviors....................21 6.1 Core modules....................................................................22 6.1.1 6.1.2 Debug trace timing specifications.......................22 JTAG electricals..................................................23 6.2 System modules................................................................26 6.3 Clock modules...................................................................26 6.3.1 6.3.2 6.3.3 MCG specifications.............................................26 Oscillator electrical specifications.......................28 32kHz Oscillator Electrical Characteristics.........30 6.4 Memories and memory interfaces.....................................31 6.4.1 6.4.2 6.4.3 Flash (FTFL) electrical specifications.................31 EzPort Switching Specifications.........................35 Flexbus Switching Specifications........................36 6.5 Security and integrity modules..........................................39 6.6 Analog...............................................................................39 6.6.1 6.6.2 6.6.3 6.6.4 ADC electrical specifications..............................39 CMP and 6-bit DAC electrical specifications......47 12-bit DAC electrical characteristics...................50 Voltage reference electrical specifications..........53 6.7 Timers................................................................................54 6.8 Communication interfaces.................................................54 6.8.1 6.8.2 6.8.3 6.8.4 6.8.5 6.8.6 Ethernet switching specifications........................55 USB electrical specifications...............................56 USB DCD electrical specifications......................56 USB VREG electrical specifications...................57 CAN switching specifications..............................57 DSPI switching specifications (low-speed mode)..................................................................58 DSPI switching specifications (high-speed mode)..................................................................59 I2C switching specifications................................61 UART switching specifications............................61 SDHC specifications...........................................61 I2S switching specifications................................62 5.2 Switching specifications.....................................................19 5.2.1 5.2.2 Device clock specifications.................................19 General switching specifications.........................20 6.9 Human-machine interfaces (HMI)......................................64 6.9.1 TSI electrical specifications................................64 5.3 Thermal specifications.......................................................21 5.3.1 5.3.2 Thermal operating requirements.........................21 Thermal attributes...............................................21 7 Dimensions...............................................................................65 7.1 Obtaining package dimensions.........................................65 8 Pinout........................................................................................65 K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. Freescale Semiconductor, Inc. Preliminary 3 8.1 K60 Signal Multiplexing and Pin Assignments..................65 8.2 K60 Pinouts.......................................................................72 9 Revision History........................................................................74 K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. 4 Preliminary Freescale Semiconductor, Inc. Ordering parts 1 Ordering parts 1.1 Determining valid orderable parts Valid orderable part numbers are provided on the web. To determine the orderable part numbers for this device, go to http://www.freescale.com and perform a part number search for the following device numbers: PK60 and MK60. 2 Part identification 2.1 Description Part numbers for the chip have fields that identify the specific part. You can use the values of these fields to determine the specific part you have received. 2.2 Format Part numbers for this device have the following format: Q K## M FFF T PP CCC N 2.3 Fields This table lists the possible values for each field in the part number (not all combinations are valid): Field Q K## M Qualification status Kinetis family Flash memory type Description Values * M = Fully qualified, general market flow * P = Prequalification * K60 * N = Program flash only * X = Program flash and FlexMemory Table continues on the next page... K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. Freescale Semiconductor, Inc. Preliminary 5 Terminology and guidelines Field FFF Description Program flash memory size * * * * * * 32 = 32 KB 64 = 64 KB 128 = 128 KB 256 = 256 KB 512 = 512 KB 1M0 = 1 MB Values T PP Temperature range (C) Package identifier * V = -40 to 105 * C = -40 to 85 * * * * * * * * * * * * * * * * * * FM = 32 QFN (5 mm x 5 mm) FT = 48 QFN (7 mm x 7 mm) LF = 48 LQFP (7 mm x 7 mm) EX = 64 QFN (9 mm x 9 mm) LH = 64 LQFP (10 mm x 10 mm) LK = 80 LQFP (12 mm x 12 mm) MB = 81 MAPBGA (8 mm x 8 mm) LL = 100 LQFP (14 mm x 14 mm) MC = 121 MAPBGA (8 mm x 8 mm) LQ = 144 LQFP (20 mm x 20 mm) MD = 144 MAPBGA (13 mm x 13 mm) MF = 196 MAPBGA (15 mm x 15 mm) MJ = 256 MAPBGA (17 mm x 17 mm) 50 = 50 MHz 72 = 72 MHz 100 = 100 MHz 120 = 120 MHz 150 = 150 MHz CCC Maximum CPU frequency (MHz) N Packaging type * R = Tape and reel * (Blank) = Trays 2.4 Example This is an example part number: MK60N512VMD100 3 Terminology and guidelines 3.1 Definition: Operating requirement An operating requirement is a specified value or range of values for a technical characteristic that you must guarantee during operation to avoid incorrect operation and possibly decreasing the useful life of the chip. K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. 6 Preliminary Freescale Semiconductor, Inc. Terminology and guidelines 3.1.1 Example This is an example of an operating requirement, which you must meet for the accompanying operating behaviors to be guaranteed: Symbol VDD Description 1.0 V core supply voltage 0.9 Min. 1.1 Max. V Unit 3.2 Definition: Operating behavior An operating behavior is a specified value or range of values for a technical characteristic that are guaranteed during operation if you meet the operating requirements and any other specified conditions. 3.2.1 Example This is an example of an operating behavior, which is guaranteed if you meet the accompanying operating requirements: Symbol IWP Description Digital I/O weak pullup/ 10 pulldown current Min. 130 Max. A Unit 3.3 Definition: Attribute An attribute is a specified value or range of values for a technical characteristic that are guaranteed, regardless of whether you meet the operating requirements. 3.3.1 Example This is an example of an attribute: Symbol CIN_D Description Input capacitance: digital pins -- Min. 7 Max. pF Unit K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. Freescale Semiconductor, Inc. Preliminary 7 Terminology and guidelines 3.4 Definition: Rating A rating is a minimum or maximum value of a technical characteristic that, if exceeded, may cause permanent chip failure: * Operating ratings apply during operation of the chip. * Handling ratings apply when the chip is not powered. 3.4.1 Example This is an example of an operating rating: Symbol VDD Description 1.0 V core supply voltage -0.3 Min. 1.2 Max. V Unit 3.5 Result of exceeding a rating 40 Failures in time (ppm) 30 20 The likelihood of permanent chip failure increases rapidly as soon as a characteristic begins to exceed one of its operating ratings. 10 0 Operating rating Measured characteristic K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. 8 Preliminary Freescale Semiconductor, Inc. Terminology and guidelines 3.6 Relationship between ratings and operating requirements go a rh nd lin g in rat g( mi n.) ir qu em en t( n. mi ) ir qu em en t( x ma .) r go ha nd lin g in rat g( x.) ma e gr e gr Op era tin Op era tin Op era tin Op era tin Fatal range - Probable permanent failure Limited operating range - No permanent failure - Possible decreased life - Possible incorrect operation Normal operating range - No permanent failure - Correct operation Limited operating range - No permanent failure - Possible decreased life - Possible incorrect operation Fatal range - Probable permanent failure Handling range - No permanent failure - 3.7 Guidelines for ratings and operating requirements Follow these guidelines for ratings and operating requirements: * Never exceed any of the chip's ratings. * During normal operation, don't exceed any of the chip's operating requirements. * If you must exceed an operating requirement at times other than during normal operation (for example, during power sequencing), limit the duration as much as possible. 3.8 Definition: Typical value A typical value is a specified value for a technical characteristic that: * Lies within the range of values specified by the operating behavior * Given the typical manufacturing process, is representative of that characteristic during operation when you meet the typical-value conditions or other specified conditions Typical values are provided as design guidelines and are neither tested nor guaranteed. 3.8.1 Example 1 This is an example of an operating behavior that includes a typical value: K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. Freescale Semiconductor, Inc. Preliminary 9 Ratings Symbol IWP Description Digital I/O weak pullup/pulldown current 10 Min. 70 Typ. 130 Max. A Unit 3.8.2 Example 2 This is an example of a chart that shows typical values for various voltage and temperature conditions: 5000 4500 4000 3500 IDD_STOP (A) 3000 2500 2000 1500 1000 500 0 0.90 0.95 1.00 VDD (V) 1.05 1.10 TJ 150 C 105 C 25 C -40 C 3.9 Typical value conditions Typical values assume you meet the following conditions (or other conditions as specified): Symbol TA VDD Description Ambient temperature 3.3 V supply voltage 25 3.3 Value C V Unit 4 Ratings K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. 10 Preliminary Freescale Semiconductor, Inc. Ratings 4.1 Thermal handling ratings Symbol TSTG TSDR Description Storage temperature Solder temperature, lead-free Solder temperature, leaded Min. -55 -- -- Max. 150 260 245 Unit C C Notes 1 2 1. Determined according to JEDEC Standard JESD22-A103, High Temperature Storage Life. 2. Determined according to IPC/JEDEC Standard J-STD-020, Moisture/Reflow Sensitivity Classification for Nonhermetic Solid State Surface Mount Devices. 4.2 Moisture handling ratings Symbol MSL Description Moisture sensitivity level Min. -- Max. 3 Unit -- Notes 1 1. Determined according to IPC/JEDEC Standard J-STD-020, Moisture/Reflow Sensitivity Classification for Nonhermetic Solid State Surface Mount Devices. 4.3 ESD handling ratings Symbol VHBM VCDM ILAT Description Electrostatic discharge voltage, human body model Electrostatic discharge voltage, charged-device model Latch-up current at ambient temperature of 85C Min. -2000 -500 -100 Max. +2000 +500 +100 Unit V V mA Notes 1 2 1. Determined according to JEDEC Standard JESD22-A114, Electrostatic Discharge (ESD) Sensitivity Testing Human Body Model (HBM). 2. Determined according to JEDEC Standard JESD22-C101, Field-Induced Charged-Device Model Test Method for Electrostatic-Discharge-Withstand Thresholds of Microelectronic Components. 4.4 Voltage and current operating ratings Symbol VDD IDD VDIO Description Digital supply voltage Digital supply current Digital input voltage (except RESET, EXTAL, and XTAL) Table continues on the next page... Min. -0.3 -- -0.3 Max. 3.8 185 5.5 Unit V mA V K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. Freescale Semiconductor, Inc. Preliminary 11 General Symbol VAIO ID VDDA VUSB_DP VUSB_DM VREGIN VBAT Description Analog, RESET, EXTAL, and XTAL input voltage Instantaneous maximum current single pin limit (applies to all port pins) Analog supply voltage USB_DP input voltage USB_DM input voltage USB regulator input RTC battery supply voltage Min. -0.3 -25 VDD - 0.3 -0.3 -0.3 -0.3 -0.3 Max. VDD + 0.3 25 VDD + 0.3 3.63 3.63 6.0 3.8 Unit V mA V V V V V 5 General 5.1 Nonswitching electrical specifications 5.1.1 Voltage and current operating requirements Table 1. Voltage and current operating requirements Symbol VDD VDDA Description Supply voltage Analog supply voltage Min. 1.71 1.71 -0.1 -0.1 1.71 Max. 3.6 3.6 0.1 0.1 3.6 Unit V V V V V Notes VDD - VDDA VDD-to-VDDA differential voltage VSS - VSSA VSS-to-VSSA differential voltage VBAT VIH RTC battery supply voltage Input high voltage * 2.7 V VDD 3.6 V * 1.7 V VDD 2.7 V VIL Input low voltage * 2.7 V VDD 3.6 V * 1.7 V VDD 2.7 V VHYS Input hysteresis 0.7 x VDD 0.75 x VDD -- -- V V -- -- 0.06 x VDD Table continues on the next page... 0.35 x VDD 0.3 x VDD -- V V V K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. 12 Preliminary Freescale Semiconductor, Inc. General Table 1. Voltage and current operating requirements (continued) Symbol IIC Description DC injection current -- single pin * VIN < VSS DC injection current -- total MCU limit, includes sum of all stressed pins * VIN < VSS VRAM VRFVBAT VDD voltage required to retain RAM VBAT voltage required to retain the VBAT register file 0 -0.2 mA 1 0 1.2 TBD -5 -- -- mA V V Min. Max. Unit Notes 1 1. All functional non-supply pins are internally clamped to VSS, and induce an injection current when VIN is less than VSS. The IIC maximum operating requirement should not be exceeded. If this requirement cannot be met, the input must be current limited to the value specified. 5.1.2 LVD and POR operating requirements Table 2. VDD supply LVD and POR operating requirements Symbol VPOR VLVDH Description Falling VDD POR detect voltage Falling low-voltage detect threshold -- high range (LVDV=01) Low-voltage warning thresholds -- high range VLVW1H VLVW2H VLVW3H VLVW4H VHYSH VLVDL * Level 1 falling (LVWV=00) * Level 2 falling (LVWV=01) * Level 3 falling (LVWV=10) * Level 4 falling (LVWV=11) Low-voltage inhibit reset/recover hysteresis -- high range Falling low-voltage detect threshold -- low range (LVDV=00) Low-voltage warning thresholds -- low range VLVW1L VLVW2L VLVW3L VLVW4L VHYSL VBG tLPO * Level 1 falling (LVWV=00) * Level 2 falling (LVWV=01) * Level 3 falling (LVWV=10) * Level 4 falling (LVWV=11) Low-voltage inhibit reset/recover hysteresis -- low range Bandgap voltage reference Internal low power oscillator period factory trimmed TBD TBD TBD TBD TBD TBD 1.80 1.90 2.00 2.10 40 1.00 1000 TBD TBD TBD TBD TBD TBD V V V V mV V s TBD TBD TBD TBD TBD 2.70 2.80 2.90 3.00 60 1.60 TBD TBD TBD TBD TBD V V V V mV V 1 Min. TBD TBD Typ. 1.1 2.56 Max. TBD TBD Unit V V 1 Notes K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. Freescale Semiconductor, Inc. Preliminary 13 General 1. Rising thresholds are falling threshold + hysteresis voltage Table 3. VBAT power operating requirements Symbol Description Min. TBD Typ. 1.1 Max. TBD Unit V Notes VPOR_VBAT Falling VBAT supply POR detect voltage 5.1.3 Voltage and current operating behaviors Table 4. Voltage and current operating behaviors Symbol VOH Description Output high voltage -- high drive strength * 2.7 V VDD 3.6 V, IOH = -10mA * 1.71 V VDD 2.7 V, IOH = -3mA Output high voltage -- low drive strength * 2.7 V VDD 3.6 V, IOH = -2mA * 1.71 V VDD 2.7 V, IOH = -0.6mA IOHT VOL Output high current total for all ports Output low voltage -- high drive strength * 2.7 V VDD 3.6 V, IOL = 10mA * 1.71 V VDD 2.7 V, IOL = 3mA Output low voltage -- low drive strength * 2.7 V VDD 3.6 V, IOL = 2mA * 1.71 V VDD 2.7 V, IOL = 0.6mA IOLT IIN IOZ RPU RPD Output low current total for all ports Input leakage current (per pin) Hi-Z (off-state) leakage current (per pin) Internal pullup resistors Internal pulldown resistors -- -- -- -- -- 30 30 0.5 0.5 100 1 1 50 50 V V mA A A k k 2 3 1 -- -- 0.5 0.5 V V VDD - 0.5 VDD - 0.5 -- -- -- 100 V V mA VDD - 0.5 VDD - 0.5 -- -- V V Min. Max. Unit Notes 1. Measured at VDD=3.6V 2. Measured at VDD supply voltage = VDD min and Vinput = VSS 3. Measured at VDD supply voltage = VDD min and Vinput = VDD 5.1.4 Power mode transition operating behaviors All specifications except tPOR, and VLLSxRUN recovery times in the following table assume this clock configuration: K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. 14 Preliminary Freescale Semiconductor, Inc. General * CPU and system clocks = 100 MHz * Bus and FlexBus clocks = 50 MHz * Flash clock = 25 MHz Table 5. Power mode transition operating behaviors Symbol tPOR Description After a POR event, amount of time from the point VDD reaches 1.8V to execution of the first instruction across the operating temperature range of the chip. RUN VLLS1 RUN * RUN VLLS1 * VLLS1 RUN RUN VLLS2 RUN * RUN VLLS2 * VLLS2 RUN RUN VLLS3 RUN * RUN VLLS3 * VLLS3 RUN RUN LLS RUN * RUN LLS * LLS RUN RUN STOP RUN * RUN STOP * STOP RUN RUN VLPS RUN * RUN VLPS * VLPS RUN 1. Normal boot (FTFL_OPT[LPBOOT]=1) -- -- 4.1 5.8 s s -- -- 4.1 4.2 s s -- -- 4.1 5.9 s s -- -- 4.1 49.2 s s -- -- 4.1 49.3 s s -- -- 4.1 123.8 s s Min. -- Max. 300 Unit s Notes 1 5.1.5 Power consumption operating behaviors Table 6. Power consumption operating behaviors Symbol IDDA Description Analog supply current Min. -- Table continues on the next page... Typ. -- Max. TBD Unit mA Notes 1 K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. Freescale Semiconductor, Inc. Preliminary 15 General Table 6. Power consumption operating behaviors (continued) Symbol IDD_RUN Description Run mode current -- all peripheral clocks disabled, code executing from flash * @ 1.8V * @ 3.0V IDD_RUN Run mode current -- all peripheral clocks enabled, code executing from flash * @ 1.8V * @ 3.0V IDD_RUN_M Run mode current -- all peripheral clocks enabled and peripherals active, code executing AX from flash * @ 1.8V * @ 3.0V IDD_WAIT IDD_WAIT IDD_STOP IDD_VLPR IDD_VLPR IDD_VLPW IDD_VLPS IDD_LLS IDD_VLLS3 Wait mode high frequency current at 3.0 V -- all peripheral clocks disabled Wait mode reduced frequency current at 3.0 V -- all peripheral clocks disabled Stop mode current at 3.0 V Very-low-power run mode current at 3.0 V -- all peripheral clocks disabled Very-low-power run mode current at 3.0 V -- all peripheral clocks enabled Very-low-power wait mode current at 3.0 V Very-low-power stop mode current at 3.0 V Low leakage stop mode current at 3.0 V Very low-leakage stop mode 3 current at 3.0 V * 128KB RAM devices * 64KB RAM devices IDD_VLLS2 IDD_VLLS1 IDD_VBAT Very low-leakage stop mode 2 current at 3.0 V Very low-leakage stop mode 1 current at 3.0 V Average current when CPU is not accessing RTC registers at 3.0 V -- -- -- -- -- 8 6 4 2 550 TBD TBD TBD TBD TBD A A A A nA 9 -- -- 55 56 TBD TBD mA mA 4 -- -- -- -- -- -- -- -- -- -- 85 85 35 15 0.4 1.25 TBD 1.05 50 12 TBD TBD TBD TBD TBD TBD TBD TBD TBD TBD mA mA mA mA mA mA mA mA A A 6 7 8 2 5 -- -- 40 42 TBD TBD mA mA 3 Min. Typ. Max. Unit Notes 2 1. The analog supply current is the sum of the active or disabled current for each of the analog modules on the device. See each module's specification for its supply current. 2. 100MHz core and system clock, 50MHz bus and FlexBus clock, and 25MHz flash clock . MCG configured for FEI mode. All peripheral clocks disabled. 3. 100MHz core and system clock, 50MHz bus and FlexBus clock, and 25MHz flash clock. MCG configured for FEI mode. All peripheral clocks enabled, but peripherals are not in active operation. 4. 100MHz core and system clock, 50MHz bus and FlexBus clock, and 25MHz flash clock. MCG configured for FEI mode. All peripheral clocks enabled, and peripherals are in active operation. 5. 25MHz core and system clock, 25MHz bus clock, and 12.5MHz FlexBus and flash clock. MCG configured for FEI mode. K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. 16 Preliminary Freescale Semiconductor, Inc. General 6. 2 MHz core, system, FlexBus, and bus clock and 1MHz flash clock. MCG configured for fast IRCLK mode. All peripheral clocks disabled. Code executing from flash. 7. 2 MHz core, system, FlexBus, and bus clock and 1MHz flash clock. MCG configured for fast IRCLK mode. All peripheral clocks enabled but peripherals are not in active operation. Code executing from flash. 8. 2 MHz core, system, FlexBus, and bus clock and 1MHz flash clock. MCG configured for fast IRCLK mode. All peripheral clocks disabled. 9. Includes 32kHz oscillator current and RTC operation. 5.1.5.1 * * * * * Diagram: Typical IDD_RUN operating behavior The following data was measured under these conditions: MCG in FEI mode (39.0625 kHz IRC), except for 1 MHz core (FBE) All peripheral clocks disabled except FTFL LVD disabled, USB regulator disabled No GPIOs toggled Code execution from flash Figure 1. Run mode supply current vs. core frequency -- all peripheral clocks disabled The following data was measured under these conditions: K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. Freescale Semiconductor, Inc. Preliminary 17 General * * * * * MCG in FEI mode (39.0625 kHz IRC), except for 1 MHz core (FBE) All peripheral clocks enabled but peripherals are not in active operation LVD disabled, USB regulator disabled No GPIOs toggled Code execution from flash Figure 2. Run mode supply current vs. core frequency -- all peripheral clocks enabled K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. 18 Preliminary Freescale Semiconductor, Inc. General 5.1.6 EMC radiated emissions operating behaviors Table 7. EMC radiated emissions operating behaviors Symbol VRE1 VRE2 VRE3 VRE4 Description Radiated emissions voltage, band 1 Radiated emissions voltage, band 2 Radiated emissions voltage, band 3 Radiated emissions voltage, band 4 Frequency band (MHz) 0.15-50 50-150 150-500 500-1000 0.15-1000 Typ. TBD TBD TBD TBD TBD -- 2, 3 Unit dBV Notes 1, 2 VRE_IEC_SAE IEC and SAE level 1. Determined according to IEC Standard 61967-1, Integrated Circuits - Measurement of Electromagnetic Emissions, 150 kHz to 1 GHz Part 1: General Conditions and Definitions, IEC Standard 61967-2, Integrated Circuits - Measurement of Electromagnetic Emissions, 150 kHz to 1 GHz Part 2: Measurement of Radiated Emissions--TEM Cell and Wideband TEM Cell Method, and SAE Standard J1752-3, Measurement of Radiated Emissions from Integrated Circuits--TEM/ Wideband TEM (GTEM) Cell Method. 2. VDD = 3 V, TA = 25 C, fOSC = 12 MHz (crystal), fSYS = 96 MHz 3. Specified according to Annex D of IEC Standard 61967-2, Measurement of Radiated Emissions--TEM Cell and Wideband TEM Cell Method, and Appendix D of SAE Standard J1752-3, Measurement of Radiated Emissions from Integrated Circuits--TEM/Wideband TEM (GTEM) Cell Method. 5.1.7 Designing with radiated emissions in mind To find application notes that provide guidance on designing your system to minimize interference from radiated emissions: 1. Go to http://www.freescale.com. 2. Perform a keyword search for "EMC design." 5.1.8 Capacitance attributes Table 8. Capacitance attributes Symbol CIN_A CIN_D Description Input capacitance: analog pins Input capacitance: digital pins Min. -- -- Max. 7 7 Unit pF pF 5.2 Switching specifications K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. Freescale Semiconductor, Inc. Preliminary 19 General 5.2.1 Device clock specifications Symbol Description Normal run mode fSYS fSYS_USB fBUS FB_CLK fFLASH System and core clock System and core clock when USB in operation Bus clock FlexBus clock Flash clock VLPR mode fSYS fBUS FB_CLK fFLASH System and core clock Bus clock FlexBus clock Flash clock -- -- -- -- 2 2 2 1 MHz MHz MHz MHz -- 20 -- -- -- 100 -- 50 50 25 MHz MHz MHz MHz MHz Min. Max. Unit Notes 5.2.2 General switching specifications These general purpose specifications apply to all signals configured for GPIO, UART, CAN, CMT, IEEE 1588 timer, and I2C signals. Symbol Description GPIO pin interrupt pulse width (digital glitch filter disabled) -- Synchronous path GPIO pin interrupt pulse width (digital glitch filter disabled, analog filter enabled) -- Asynchronous path GPIO pin interrupt pulse width (digital glitch filter disabled, analog filter disabled) -- Asynchronous path External reset pulse width (digital glitch filter disabled) Mode select (EZP_CS) hold time after reset deassertion Port rise and fall time (high drive strength) * Slew disabled * Slew enabled Port rise and fall time (low drive strength) * Slew disabled * Slew enabled 1. The greater synchronous and asynchronous timing must be met. 2. This is the shortest pulse that is guaranteed to be recognized. 3. 75pF load -- -- 32 36 ns ns -- -- 12 36 ns ns 4 Min. 1.5 100 16 TBD 2 Max. -- -- -- -- -- Bus clock cycles 3 Unit Bus clock cycles ns ns Notes 1 2 2 K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. 20 Preliminary Freescale Semiconductor, Inc. Peripheral operating requirements and behaviors 4. 15pF load 5.3 Thermal specifications 5.3.1 Thermal operating requirements Table 9. Thermal operating requirements Symbol TJ TA Description Die junction temperature Ambient temperature Min. -40 -40 Max. 125 105 Unit C C 5.3.2 Thermal attributes Board type Singlelayer (1s) Fourlayer (2s2p) Singlelayer (1s) Fourlayer (2s2p) -- -- -- Symbol Description RJA Thermal resistance, junction to ambient (natural convection) Thermal resistance, junction to ambient (natural convection) Thermal resistance, junction to ambient (200 ft./min. air speed) Thermal resistance, junction to ambient (200 ft./min. air speed) Thermal resistance, junction to board Thermal resistance, junction to case Thermal characterization parameter, junction to package top outside center (natural convection) 144 LQFP 52 144 81 80 MAPBGA MAPBGA LQFP 50 TBD TBD Unit C/W Notes 1 RJA 44 30 TBD TBD C/W 1 RJMA 43 41 TBD TBD C/W 1 RJMA 38 27 TBD TBD C/W 1 RJB RJC JT 33 11 2 17 10 2 TBD TBD TBD TBD TBD TBD C/W C/W C/W 2 3 4 1. Determined according to JEDEC Standard JESD51-2, Integrated Circuits Thermal Test Method Environmental Conditions--Natural Convection (Still Air), or EIA/JEDEC Standard JESD51-6, Integrated Circuit Thermal Test Method Environmental Conditions--Forced Convection (Moving Air). 6 Peripheral operating requirements and behaviors All digital I/O switching characteristics assume: 1. output pins K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. Freescale Semiconductor, Inc. Preliminary 21 Peripheral operating requirements and behaviors * have CL=30pF loads, * are configured for fast slew rate (PORTx_PCRn[SRE]=0), and * are configured for high drive strength (PORTx_PCRn[DSE]=1) 2. input pins * have their passive filter disabled (PORTx_PCRn[PFE]=0) 6.1 Core modules 6.1.1 Debug trace timing specifications Table 10. Debug trace operating behaviors Symbol Tcyc Twl Twh Tr Tf Ts Th Description Clock period Low pulse width High pulse width Clock and data rise time Clock and data fall time Data setup Data hold Min. Max. Unit MHz ns ns ns ns ns ns Frequency dependent 2 2 -- -- 3 2 -- -- 3 3 -- -- Figure 3. TRACE_CLKOUT specifications TRACE_CLKOUT Ts Th Ts Th TRACE_D[3:0] Figure 4. Trace data specifications K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. 22 Preliminary Freescale Semiconductor, Inc. Peripheral operating requirements and behaviors 6.1.2 JTAG electricals Table 11. JTAG limited voltage range electricals Symbol Description Operating voltage J1 TCLK frequency of operation * Boundary Scan * JTAG and CJTAG * Serial Wire Debug J2 J3 TCLK cycle period TCLK clock pulse width * Boundary Scan * JTAG and CJTAG * Serial Wire Debug J4 J5 J6 J7 J8 J9 J10 J11 J12 J13 J14 TCLK rise and fall times Boundary scan input data setup time to TCLK rise Boundary scan input data hold time after TCLK rise TCLK low to boundary scan output data valid TCLK low to boundary scan output high-Z TMS, TDI input data setup time to TCLK rise TMS, TDI input data hold time after TCLK rise TCLK low to TDO data valid TCLK low to TDO high-Z TRST assert time TRST setup time (negation) to TCLK high 50 20 10 -- 20 0 -- -- 8 1 -- -- 100 8 3 -- -- 25 25 -- -- 17 17 -- -- ns ns ns ns ns ns ns ns ns ns ns -- -- 0 0 0 1/J1 10 25 50 -- ns ns Min. 2.7 Max. 3.6 Unit V MHz Table 12. JTAG full voltage range electricals Symbol Description Operating voltage J1 TCLK frequency of operation * Boundary Scan * JTAG and CJTAG * Serial Wire Debug J2 TCLK cycle period Table continues on the next page... 0 0 0 1/J1 10 20 40 -- ns Min. 1.71 Max. 3.6 Unit V MHz K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. Freescale Semiconductor, Inc. Preliminary 23 Peripheral operating requirements and behaviors Table 12. JTAG full voltage range electricals (continued) Symbol J3 Description TCLK clock pulse width * Boundary Scan * JTAG and CJTAG * Serial Wire Debug J4 J5 J6 J7 J8 J9 J10 J11 J12 J13 J14 TCLK rise and fall times Boundary scan input data setup time to TCLK rise Boundary scan input data hold time after TCLK rise TCLK low to boundary scan output data valid TCLK low to boundary scan output high-Z TMS, TDI input data setup time to TCLK rise TMS, TDI input data hold time after TCLK rise TCLK low to TDO data valid TCLK low to TDO high-Z TRST assert time TRST setup time (negation) to TCLK high 50 25 12.5 -- 20 0 -- -- 8 1.4 -- -- 100 8 3 -- -- 25 25 -- -- 22.1 22.1 -- -- ns ns ns ns ns ns ns ns ns ns ns -- -- Min. Max. Unit ns J2 J3 J3 TCLK (input) J4 J4 Figure 5. Test clock input timing K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. 24 Preliminary Freescale Semiconductor, Inc. Peripheral operating requirements and behaviors TCLK J5 J6 Data inputs J7 Input data valid Data outputs J8 Output data valid Data outputs J7 Data outputs Output data valid Figure 6. Boundary scan (JTAG) timing TCLK J9 J10 TDI/TMS J11 Input data valid TDO J12 Output data valid TDO J11 TDO Output data valid Figure 7. Test Access Port timing K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. Freescale Semiconductor, Inc. Preliminary 25 Peripheral operating requirements and behaviors TCLK J14 J13 TRST Figure 8. TRST timing 6.2 System modules There are no specifications necessary for the device's system modules. 6.3 Clock modules 6.3.1 MCG specifications Table 13. MCG specifications Symbol fints_ft fints_t Iints tirefsts fdco_res_t Description Internal reference frequency (slow clock) -- factory trimmed at nominal VDD and 25C Internal reference frequency (slow clock) -- user trimmed Internal reference (slow clock) current Internal reference (slow clock) startup time Resolution of trimmed DCO output frequency at fixed voltage and temperature -- using SCTRIM and SCFTRIM Resolution of trimmed DCO output frequency at fixed voltage and temperature -- using SCTRIM only Total deviation of trimmed average DCO output frequency over voltage and temperature Total deviation of trimmed average DCO output frequency over fixed voltage and temperature range of 0-70C Internal reference frequency (fast clock) -- factory trimmed at nominal VDD and 25C Internal reference frequency (fast clock) -- user trimmed Min. -- 31.25 -- -- -- Typ. 32.768 -- TBD TBD 0.1 Max. -- 39.0625 -- 4 0.3 Unit kHz kHz A s %fdco 1 Notes fdco_res_t -- 0.2 0.5 %fdco 1 fdco_t fdco_t -- + 0.5 - 1.0 3.5 %fdco %fdco 1 -- 0.5 TBD 1 fintf_ft fintf_t 3.4 3 -- -- 4 5 MHz MHz Table continues on the next page... K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. 26 Preliminary Freescale Semiconductor, Inc. Peripheral operating requirements and behaviors Table 13. MCG specifications (continued) Symbol Iintf tirefstf floc_low floc_high Description Internal reference (fast clock) current Internal reference startup time (fast clock) Loss of external clock minimum frequency -- RANGE = 00 Loss of external clock minimum frequency -- RANGE = 01, 10, or 11 FLL ffll_ref fdco FLL reference frequency range DCO output frequency range Low range (DRS=00) 640 x ffll_ref Mid range (DRS=01) 1280 x ffll_ref Mid-high range (DRS=10) 1920 x ffll_ref High range (DRS=11) 2560 x ffll_ref fdco_t_DMX3 DCO output frequency 2 Low range (DRS=00) 732 x ffll_ref Mid range (DRS=01) 1464 x ffll_ref Mid-high range (DRS=10) 2197 x ffll_ref High range (DRS=11) 2929 x ffll_ref Jcyc_fll Jacc_fll tfll_acquire FLL period jitter FLL accumulated jitter of DCO output over a 1s time window FLL target frequency acquisition time PLL fvco Ipll VCO operating frequency PLL operating current * PLL @ 96 MHz (fosc_hi_1=8MHz, fpll_ref=2MHz, VDIV multiplier=48) PLL reference frequency range PLL period jitter PLL accumulated jitter over 1s window 48.0 -- -- 950 100 -- MHz A 8 -- -- -- TBD TBD -- TBD TBD 1 ps ps ms 6 6 7 -- 95.98 -- MHz -- 71.99 -- MHz -- 47.97 -- MHz -- 23.99 -- MHz 4, 5 80 83.89 100 MHz 60 62.91 75 MHz 40 41.94 50 MHz 31.25 20 -- 20.97 39.0625 25 kHz MHz 2, 3 Min. -- -- (3/5) x fints_t (16/5) x fints_t Typ. TBD TBD -- -- Max. -- TBD -- -- Unit A s kHz kHz Notes fpll_ref Jcyc_pll Jacc_pll 2.0 -- -- -- 400 TBD 4.0 -- -- MHz ps ps 9, 10 9, 10 Table continues on the next page... K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. Freescale Semiconductor, Inc. Preliminary 27 Peripheral operating requirements and behaviors Table 13. MCG specifications (continued) Symbol Dlock Dunl tpll_lock Description Lock entry frequency tolerance Lock exit frequency tolerance Lock detector detection time Min. 1.49 4.47 -- Typ. -- -- -- Max. 2.98 5.97 0.15 + 1075(1/ fpll_ref) Unit % % ms 11 Notes 1. This parameter is measured with the internal reference (slow clock) being used as a reference to the FLL (FEI clock mode). 2. These typical values listed are with the slow internal reference clock (FEI) using factory trim and DMX32=0. 3. The resulting system clock frequencies should not exceed their maximum specified values. The DCO frequency deviation (fdco_t) over voltage and temperature should be considered. 4. These typical values listed are with the slow internal reference clock (FEI) using factory trim and DMX32=1. 5. The resulting clock frequency must not exceed the maximum specified clock frequency of the device. 6. This specification was obtained at TBD frequency. 7. This specification applies to any time the FLL reference source or reference divider is changed, trim value is changed, DMX32 bit is changed, DRS bits are changed, or changing from FLL disabled (BLPE, BLPI) to FLL enabled (FEI, FEE, FBE, FBI). If a crystal/resonator is being used as the reference, this specification assumes it is already running. 8. Excludes any oscillator currents that are also consuming power while PLL is in operation. 9. This specification was obtained using a Freescale developed PCB. PLL jitter is dependent on the noise characteristics of each PCB and results will vary. 10. This specification was obtained at internal frequency of TBD. 11. This specification applies to any time the PLL VCO divider or reference divider is changed, or changing from PLL disabled (BLPE, BLPI) to PLL enabled (PBE, PEE). If a crystal/resonator is being used as the reference, this specification assumes it is already running. 6.3.2 Oscillator electrical specifications This section provides the electrical characteristics of the module. 6.3.2.1 Symbol VDD IDDOSC Oscillator DC electrical specifications Description Supply voltage Supply current -- low-power mode (HGO=0) * 32 kHz * 4 MHz * 8 MHz * 16 MHz * 24 MHz * 32 MHz -- -- -- -- -- -- Min. 1.71 Table 14. Oscillator DC electrical specifications Typ. -- Max. 3.6 Unit V 1 500 200 300 700 1.2 1.5 -- -- -- -- -- -- nA A A A mA mA Notes Table continues on the next page... K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. 28 Preliminary Freescale Semiconductor, Inc. Peripheral operating requirements and behaviors Table 14. Oscillator DC electrical specifications (continued) Symbol IDDOSC Description Supply current -- high gain mode (HGO=1) * 32 kHz * 4 MHz * 8 MHz * 16 MHz * 24 MHz * 32 MHz Cx Cy RF EXTAL load capacitance XTAL load capacitance Feedback resistor -- low-frequency, low-power mode (HGO=0) Feedback resistor -- low-frequency, high-gain mode (HGO=1) Feedback resistor -- high-frequency, low-power mode (HGO=0) Feedback resistor -- high-frequency, high-gain mode (HGO=1) RS Series resistor -- low-frequency, low-power mode (HGO=0) Series resistor -- low-frequency, high-gain mode (HGO=1) Series resistor -- high-frequency, low-power mode (HGO=0) Series resistor -- high-frequency, high-gain mode (HGO=1) -- Vpp5 Peak-to-peak amplitude of oscillation (oscillator mode) -- low-frequency, low-power mode (HGO=0) Peak-to-peak amplitude of oscillation (oscillator mode) -- low-frequency, high-gain mode (HGO=1) Peak-to-peak amplitude of oscillation (oscillator mode) -- high-frequency, low-power mode (HGO=0) Peak-to-peak amplitude of oscillation (oscillator mode) -- high-frequency, high-gain mode (HGO=1) 1. 2. 3. 4. -- 0 0.6 -- -- k V -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 25 400 800 1.5 3 4 -- -- -- 10 -- 1 -- 200 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- M M M M k k k A A A mA mA mA 2, 3 2, 3 2, 4 Min. Typ. Max. Unit Notes 1 -- VDD -- V -- 0.6 -- V -- VDD -- V VDD=3.3 V, Temperature =25 C See crystal or resonator manufacturer's recommendation Cx,Cy can be provided by using either the integrated capacitors or by using external components. When low power mode is selected, RF is integrated and must not be attached externally. K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. Freescale Semiconductor, Inc. Preliminary 29 Peripheral operating requirements and behaviors 5. The EXTAL and XTAL pins should only be connected to required oscillator components and must not be connected to any other devices. 6.3.2.2 Symbol fosc_lo fosc_hi_1 Oscillator frequency specifications Description Oscillator crystal or resonator frequency -- low frequency mode (MCG_C2[RANGE]=00) Oscillator crystal or resonator frequency -- high frequency mode (low range) (MCG_C2[RANGE]=01) Oscillator crystal or resonator frequency -- high frequency mode (high range) (MCG_C2[RANGE]=1x) Input clock frequency (external clock mode) Input clock duty cycle (external clock mode) Crystal startup time -- 32 kHz low-frequency, low-power mode (HGO=0) Crystal startup time -- 32 kHz low-frequency, high-gain mode (HGO=1) Crystal startup time -- 8 MHz high-frequency (MCG_C2[RANGE]=01), low-power mode (HGO=0) Crystal startup time -- 8 MHz high-frequency (MCG_C2[RANGE]=01), high-gain mode (HGO=1) Min. 32 3 Table 15. Oscillator frequency specifications Typ. -- -- Max. 40 8 Unit kHz MHz Notes fosc_hi_2 8 -- 32 MHz fec_extal tdc_extal tcst -- 40 -- -- -- -- 50 TBD 800 4 50 60 -- -- -- MHz % ms ms ms 1 2, 3 -- 3 -- ms 1. Other frequency limits may apply when external clock is being used as a reference for the FLL or PLL 2. Proper PC board layout procedures must be followed to achieve specifications. 3. Crystal startup time is defined as the time between the oscillator being enabled and the OSCINIT bit in the MCG_S register being set. 6.3.3 32kHz Oscillator Electrical Characteristics This section describes the module electrical characteristics. 6.3.3.1 Symbol VBAT RF Cpara 32kHz oscillator DC electrical specifications Description Supply voltage Internal feedback resistor Parasitical capacitance of EXTAL32 and XTAL32 Min. 1.71 -- -- Table 16. 32kHz oscillator DC electrical specifications Typ. -- 100 2.5 Max. 3.6 -- -- Unit V M pF Table continues on the next page... K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. 30 Preliminary Freescale Semiconductor, Inc. Peripheral operating requirements and behaviors Table 16. 32kHz oscillator DC electrical specifications (continued) Symbol Cload Vpp Description Internal load capacitance (programmable) Peak-to-peak amplitude of oscillation Min. -- -- Typ. 15 0.6 Max. -- -- Unit pF V 6.3.3.2 Symbol fosc_lo tstart 32kHz oscillator frequency specifications Description Oscillator crystal Crystal start-up time Min. -- -- Table 17. 32kHz oscillator frequency specifications Typ. 32 1000 Max. -- -- Unit kHz ms 1 Notes 1. Proper PC board layout procedures must be followed to achieve specifications. 6.4 Memories and memory interfaces 6.4.1 Flash (FTFL) electrical specifications This section describes the electrical characteristics of the FTFL module. 6.4.1.1 Flash timing specifications -- program and erase The following specifications represent the amount of time the internal charge pumps are active and do not include command overhead. Table 18. NVM program/erase timing specifications Symbol thvpgm4 thversscr Description Longword Program high-voltage time Sector Erase high-voltage time Min. -- -- -- Typ. 20 20 160 Max. TBD 100 800 Unit s ms ms 1 1 Notes thversblk256k Erase Block high-voltage time for 256 KB 1. Maximum time based on expectations at cycling end-of-life. K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. Freescale Semiconductor, Inc. Preliminary 31 Peripheral operating requirements and behaviors 6.4.1.2 Symbol Flash timing specifications -- commands Description Read 1s Block execution time Min. Table 19. Flash command timing specifications Typ. Max. Unit Notes trd1blk256k trd1sec2k tpgmchk trdrsrc tpgm4 * 256 KB data flash Read 1s Section execution time (flash sector) Program Check execution time Read Resource execution time Program Longword execution time Erase Flash Block execution time -- -- -- -- -- -- -- -- -- 50 1.4 40 35 35 TBD ms s s s s 2 1 1 1 tersblk256k tersscr * 256 KB data flash Erase Flash Sector execution time Program Section execution time -- -- 160 20 800 100 ms ms 2 tpgmsec512 tpgmsec1k tpgmsec2k trd1all trdonce tpgmonce tersall tvfykey * 512 B flash * 1 KB flash * 2 KB flash Read 1s All Blocks execution time Read Once execution time Program Once execution time Erase All Blocks execution time Verify Backdoor Access Key execution time Program Partition for EEPROM execution time -- -- -- -- -- -- -- -- TBD TBD TBD -- -- 50 320 -- TBD TBD TBD 2.8 35 TBD 1600 35 ms ms ms ms s s ms s 2 1 1 tpgmpart256k * 256 KB FlexNVM Set FlexRAM Function execution time: -- 175 TBD ms tsetram32k tsetram256k * 32 KB EEPROM backup * 256 KB EEPROM backup -- -- TBD TBD TBD TBD ms ms Byte-write to FlexRAM for EEPROM operation teewr8bers Byte-write to erased FlexRAM location execution time Byte-write to FlexRAM execution time: teewr8b32k teewr8b64k teewr8b128k teewr8b256k * 32 KB EEPROM backup * 64 KB EEPROM backup * 128 KB EEPROM backup * 256 KB EEPROM backup -- -- -- -- TBD TBD TBD TBD TBD 1.5 TBD 2.5 ms ms ms ms -- 100 TBD s 3 Word-write to FlexRAM for EEPROM operation Table continues on the next page... K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. 32 Preliminary Freescale Semiconductor, Inc. Peripheral operating requirements and behaviors Table 19. Flash command timing specifications (continued) Symbol teewr16bers Description Word-write to erased FlexRAM location execution time Word-write to FlexRAM execution time: teewr16b32k teewr16b64k teewr16b128k teewr16b256k * 32 KB EEPROM backup * 64 KB EEPROM backup * 128 KB EEPROM backup * 256 KB EEPROM backup -- -- -- -- TBD TBD TBD TBD TBD 1.5 TBD 2.5 ms ms ms ms Min. -- Typ. 100 Max. TBD Unit s Notes Longword-write to FlexRAM for EEPROM operation teewr32bers Longword-write to erased FlexRAM location execution time Longword-write to FlexRAM execution time: teewr32b32k teewr32b64k teewr32b128k teewr32b256k * 32 KB EEPROM backup * 64 KB EEPROM backup * 128 KB EEPROM backup * 256 KB EEPROM backup -- -- -- -- TBD TBD TBD TBD TBD 2.7 TBD 3.7 ms ms ms ms -- 200 TBD s 1. Assumes 25MHz flash clock frequency. 2. Maximum times for erase parameters based on expectations at cycling end-of-life. 3. For byte-writes to an erased FlexRAM location, the aligned word containing the byte must be erased. 6.4.1.3 Flash (FTFL) current and power specfications Description Worst case programming current in program flash Table 20. Flash (FTFL) current and power specfications Typ. 10 Unit mA Symbol IDD_PGM 6.4.1.4 Symbol Reliability specifications Description Table 21. NVM reliability specifications Min. Program Flash Typ.1 Max. Unit Notes tnvmretp10k tnvmretp1k tnvmretp100 nnvmcycp Data retention after up to 10 K cycles Data retention after up to 1 K cycles Data retention after up to 100 cycles Cycling endurance 5 10 15 10 K Data Flash TBD TBD TBD TBD -- -- -- -- years years years cycles 2 2 2 3 tnvmretd10k Data retention after up to 10 K cycles 5 TBD -- years 2 Table continues on the next page... K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. Freescale Semiconductor, Inc. Preliminary 33 Peripheral operating requirements and behaviors Table 21. NVM reliability specifications (continued) Symbol tnvmretd1k tnvmretd100 nnvmcycd Description Data retention after up to 1 K cycles Data retention after up to 100 cycles Cycling endurance Min. 10 15 10 K FlexRAM as EEPROM tnvmretee100 Data retention up to 100% of write endurance tnvmretee10 tnvmretee1 Data retention up to 10% of write endurance Data retention up to 1% of write endurance Write endurance nnvmwree16 nnvmwree128 nnvmwree512 nnvmwree4k nnvmwree32k * EEPROM backup to FlexRAM ratio = 16 * EEPROM backup to FlexRAM ratio = 128 * EEPROM backup to FlexRAM ratio = 512 * EEPROM backup to FlexRAM ratio = 4096 * EEPROM backup to FlexRAM ratio = 32,768 35 K 315 K 1.27 M 10 M 80 M TBD TBD TBD TBD TBD -- -- -- -- -- writes writes writes writes writes 5 10 15 TBD TBD TBD -- -- -- years years years 2 2 2 4 Typ.1 TBD TBD TBD Max. -- -- -- Unit years years cycles Notes 2 2 3 1. Typical data retention values are based on intrinsic capability of the technology measured at high temperature derated to 25C. For additional information on how Freescale defines typical data retention, please refer to Engineering Bulletin EB618. 2. Data retention is based on Tjavg = 55C (temperature profile over the lifetime of the application). 3. Cycling endurance represents number of program/erase cycles at -40C Tj 125C. 4. Write endurance represents the number of writes to each FlexRAM location at -40C Tj 125C influenced by the cycling endurance of the FlexNVM (same value as data flash) and the allocated EEPROM backup per subsystem. Minimum value assumes all byte-writes to FlexRAM. 6.4.1.5 Write endurance to FlexRAM for EEPROM When the FlexNVM partition code is not set to full data flash, the EEPROM data set size can be set to any of several non-zero values. The bytes not assigned to data flash via the FlexNVM partition code are used by the FTFL to obtain an effective endurance increase for the EEPROM data. The built-in EEPROM record management system raises the number of program/erase cycles that can be attained prior to device wear-out by cycling the EEPROM data through a larger EEPROM NVM storage space. While different partitions of the FlexNVM are available, the intention is that a single choice for the FlexNVM partition code and EEPROM data set size is used throughout the entire lifetime of a given application. The EEPROM endurance equation and graph shown below assume that only one configuration is ever used. Writes_subsystem = EEPROM - 2 x EEESPLIT x EEESIZE EEESPLIT x EEESIZE x Write_efficiency x nnvmcycd K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. 34 Preliminary Freescale Semiconductor, Inc. Peripheral operating requirements and behaviors where * Writes_subsystem -- minimum number of writes to each FlexRAM location for subsystem (each subsystem can have different endurance) * EEPROM -- allocated FlexNVM for each EEPROM subsystem based on DEPART; entered with Program Partition command * EEESPLIT -- FlexRAM split factor for subsystem; entered with the Program Partition command * EEESIZE -- allocated FlexRAM based on DEPART; entered with Program Partition command * Write_efficiency -- * 0.25 for 8-bit writes to FlexRAM * 0.50 for 16-bit or 32-bit writes to FlexRAM * nnvmcycd -- data flash cycling endurance Figure 9. EEPROM backup writes to FlexRAM K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. Freescale Semiconductor, Inc. Preliminary 35 Peripheral operating requirements and behaviors 6.4.2 EzPort Switching Specifications Table 22. EzPort switching specifications Num Description Operating voltage EP1 EP1a EP2 EP3 EP4 EP5 EP6 EP7 EP8 EP9 EZP_CK frequency of operation (all commands except READ) EZP_CK frequency of operation (READ command) EZP_CS negation to next EZP_CS assertion EZP_CS input valid to EZP_CK high (setup) EZP_CK high to EZP_CS input invalid (hold) EZP_D input valid to EZP_CK high (setup) EZP_CK high to EZP_D input invalid (hold) EZP_CK low to EZP_Q output valid (setup) EZP_CK low to EZP_Q output invalid (hold) EZP_CS negation to EZP_Q tri-state Min. 2.7 -- -- 2 x tEZP_CK 5 5 2 5 -- 0 -- Max. 3.6 fSYS/2 fSYS/8 -- -- -- -- -- 12 -- 12 Unit V MHz MHz ns ns ns ns ns ns ns ns EZP_CK EP3 EP4 EP2 EZP_CS EP7 EP8 EP9 EZP_Q (output) EP5 EP6 EZP_D (input) Figure 10. EzPort Timing Diagram 6.4.3 Flexbus Switching Specifications All processor bus timings are synchronous; input setup/hold and output delay are given in respect to the rising edge of a reference clock, FB_CLK. The FB_CLK frequency may be the same as the internal system bus frequency or an integer divider of that frequency. K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. 36 Preliminary Freescale Semiconductor, Inc. Peripheral operating requirements and behaviors The following timing numbers indicate when data is latched or driven onto the external bus, relative to the Flexbus output clock (FB_CLK). All other timing relationships can be derived from these values. Table 23. Flexbus switching specifications Num Description Operating voltage Frequency of operation FB1 FB2 FB3 FB4 FB5 Clock period Address, data, and control output valid Address, data, and control output hold Data and FB_TA input setup Data and FB_TA input hold Min. 2.7 -- 20 TBD 0 8.5 0.5 Max. 3.6 50 -- 11.5 -- -- -- Unit V Mhz ns ns ns ns ns 1 1 2 2 Notes 1. Specification is valid for all FB_AD[31:0], FB_BE/BWEn, FB_CSn, FB_OE, FB_R/W,FB_TBST, FB_TSIZ[1:0], FB_ALE, and FB_TS. 2. Specification is valid for all FB_AD[31:0] and FB_TA. K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. Freescale Semiconductor, Inc. Preliminary 37 Peripheral operating requirements and behaviors FB1 FB_CLK FB3 FB5 FB_A[Y] FB2 Address FB4 Data FB_D[X] FB_RW FB_TS FB_ALE Address AA=1 FB_CSn FB_OEn FB4 AA=0 FB_BEn FB5 AA=1 FB_TA FB_TSIZ[1:0] AA=0 TSIZ Figure 11. FlexBus read timing diagram K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. 38 Preliminary Freescale Semiconductor, Inc. Peripheral operating requirements and behaviors FB1 FB_CLK FB2 FB3 Address FB_A[Y] FB_D[X] FB_RW FB_TS FB_ALE Address Data AA=1 FB_CSn FB_OEn FB4 AA=0 FB_BEn FB5 AA=1 FB_TA FB_TSIZ[1:0] AA=0 TSIZ Figure 12. FlexBus write timing diagram 6.5 Security and integrity modules There are no specifications necessary for the device's security and integrity modules. 6.6 Analog K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. Freescale Semiconductor, Inc. Preliminary 39 Peripheral operating requirements and behaviors 6.6.1 ADC electrical specifications The 16-bit accuracy specifications listed in Table 24 and Table 25 are achievable on the differential pins ADCx_DP0, ADCx_DM0, ADCx_DP1, ADCx_DM1, ADCx_DP3, and ADCx_DP3. The ADCx_DP2 and ADCx_DM2 ADC inputs are used as the PGA inputs and are not direct device pins. Accuracy specifications for these pins are defined in Table 26 and Table 27. All other ADC channels meet the 13-bit differential/12-bit single-ended accuracy specifications. 6.6.1.1 Symbol VDDA VDDA VSSA VREFH VREFL VADIN CADIN 16-bit ADC operating conditions Description Supply voltage Supply voltage Ground voltage ADC reference voltage high Reference voltage low Input voltage Input capacitance * 16 bit modes * 8/10/12 bit modes Conditions Absolute Delta to VDD (VDDVDDA) Delta to VSS (VSSVSSA) Min. 1.71 -100 -100 1.13 VSSA VREFL -- -- Table 24. 16-bit ADC operating conditions Typ.1 -- 0 0 VDDA VSSA -- 8 4 Max. 3.6 +100 +100 VDDA VSSA VREFH 10 5 Unit V mV mV V V V pF 2 2 Notes RADIN RAS Input resistance Analog source resistance 13/12 bit modes fADCK < 4MHz 13 bit modes -- 2 5 k 3 -- -- 5 k fADCK fADCK ADC conversion clock frequency ADC conversion clock frequency 4 1.0 -- 18.0 MHz 5 2.0 -- 12.0 MHz 16 bit modes Table continues on the next page... K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. 40 Preliminary Freescale Semiconductor, Inc. Peripheral operating requirements and behaviors Table 24. 16-bit ADC operating conditions (continued) Symbol Crate Description ADC conversion rate Conditions 13 bit modes No ADC hardware averaging Continuous conversions enabled Peripheral clock = 50MHz Crate ADC conversion rate 16 bit modes No ADC hardware averaging Continuous conversions enabled Peripheral clock = 50MHz 1. Typical values assume VDDA = 3.0 V, Temp = 25C, fADCK = 1.0 MHz unless otherwise stated. Typical values are for reference only and are not tested in production. 2. DC potential difference. 3. This resistance is external to MCU. The analog source resistance should be kept as low as possible in order to achieve the best results. The results in this datasheet were derived from a system which has <8 analog source resistance. The RAS/ CAS time constant should be kept to <1ns. 4. In order to use the maximum ADC conversion clock frequency ADHSC bit should be set and the ADLPC should be clear. 5. In order to use the maximum ADC conversion clock frequency ADHSC bit should be set and the ADLPC should be clear. 6. For guidelines and examples of conversion rate calculation please download the ADC calculator tool http:// cache.freescale.com/files/soft_dev_tools/software/app_software/converters/ADC_CALCULATOR_CNV.zip?fpsp=1 7. For guidelines and examples of conversion rate calculation please download the ADC calculator tool http:// cache.freescale.com/files/soft_dev_tools/software/app_software/converters/ADC_CALCULATOR_CNV.zip?fpsp=1 37.037 -- 361.402 Ksps 7 18.484 -- 818.330 Ksps Min. Typ.1 Max. Unit Notes 6 K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. Freescale Semiconductor, Inc. Preliminary 41 Peripheral operating requirements and behaviors SIMPLIFIED INPUT PIN EQUIVALENT CIRCUIT Z ADIN SIMPLIFIED CHANNEL SELECT CIRCUIT Z AS R AS V ADIN V AS C AS Pad leakage due to input protection R ADIN ADC SAR ENGINE R ADIN INPUT PIN R ADIN INPUT PIN R ADIN C ADIN INPUT PIN Figure 13. ADC input impedance equivalency diagram 6.6.1.2 Symbol IDDA Table 25. 16-bit ADC characteristics (VREFH = VDDA, VREFL = VSSA) Description Supply current ADC asynchronous clock source * ADLPC=1, ADHSC=0 * ADLPC=1, ADHSC=1 * ADLPC=0, ADHSC=0 * ADLPC=0, ADHSC=1 Sample Time Conditions1 Min. 0.215 -- -- -- -- Typ.2 -- 2.4 4.0 5.2 6.2 Max. 1.7 -- -- -- -- Unit mA MHz MHz MHz MHz Notes 3 tADACK = 1/ fADACK 16-bit ADC electrical characteristics fADACK See Reference Manual chapter for sample times Conversion Time The ADC calculator tool can be used to determine ADC conversion times for different ADC configurations: http://cache.freescale.com/files/soft_dev_tools/software/app_software/ converters/ADC_CALCULATOR_CNV.zip?fpsp=1 TUE Total unadjusted error * 13 bit modes * <12 bit modes 0.8 0.5 TBD 1 LSB4 ADC conversion clock <12MHz, Max hardware averaging (AVGE = %1, AVGS = %11) Table continues on the next page... K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. 42 Preliminary Freescale Semiconductor, Inc. Peripheral operating requirements and behaviors Table 25. 16-bit ADC characteristics (VREFH = VDDA, VREFL = VSSA) (continued) Symbol DNL Description Differential nonlinearity Conditions1 * 13 bit modes * <12 bit modes Min. Typ.2 0.7 0.2 Max. TBD 0.5 Unit LSB4 Notes ADC conversion clock <12MHz, Max hardware averaging (AVGE = %1, AVGS = %11) Max averaging VADIN = VDDA INL Integral nonlinearity Full-scale error * 13 bit modes * <12 bit modes * 13 bit modes * <12 bit modes -- -- -- -- -- -- 1.0 0.5 0.4 1.0 -1 to 0 -- TBD TBD TBD TBD -- 0.5 LSB4 EFS EQ LSB4 Quantization error * 16 bit modes * 13 bit modes LSB4 ENOB Effective number 16 bit differential mode of bits * Avg=32 * Avg=1 16 bit single-ended mode * Avg=32 * Avg=1 5 TBD TBD 13.6 13.2 TBD TBD bits bits TBD TBD TBD TBD 6.02 x ENOB + 1.76 TBD TBD bits bits dB 5 SINAD THD Signal-to-noise plus distortion Total harmonic distortion See ENOB 16 bit differential mode * Avg=32 16 bit single-ended mode * Avg=32 -- -- -94 TBD TBD TBD dB dB 5 SFDR Spurious free dynamic range 16 bit differential mode * Avg=32 16 bit single-ended mode * Avg=32 TBD TBD -- dB TBD 95 -- dB Table continues on the next page... K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. Freescale Semiconductor, Inc. Preliminary 43 Peripheral operating requirements and behaviors Table 25. 16-bit ADC characteristics (VREFH = VDDA, VREFL = VSSA) (continued) Symbol EIL Description Input leakage error Conditions1 Min. Typ.2 IIn x RAS Max. Unit mV Notes IIn = leakage current (refer to the MCU's voltage and current operating ratings) Temp sensor slope VTEMP25 Temp sensor voltage * -40C to 25C * 25C to 105C 25C -- -- -- TBD TBD TBD -- -- -- mV/C mV/C mV 1. All accuracy numbers assume the ADC is calibrated with VREFH = VDDA 2. Typical values assume VDDA = 3.0 V, Temp = 25C, fADCK = 2.0 MHz unless otherwise stated. Typical values are for reference only and are not tested in production. 3. The ADC supply current depends on the ADC conversion clock speed, conversion rate and the ADLPC bit (low power). For lowest power operation the ADLPC bit should be set, the HSC bit should be clear with 1MHz ADC conversion clock speed. 4. 1 LSB = (VREFH - VREFL)/2N 5. Input data is 1 kHz sine wave. FIGURE TBD Figure 14. Typical TUE vs. ADC conversion rate 12-bit single-ended mode FIGURE TBD Figure 15. Typical ENOB vs. Averaging for 16-bit differential and 16-bit single-ended modes 6.6.1.3 Symbol VDDA VREFPGA VADIN VCM 16-bit ADC with PGA operating conditions Description Supply voltage PGA ref voltage Input voltage Input Common Mode range Conditions Absolute Min. 1.71 Typ.1 -- Table 26. 16-bit ADC with PGA operating conditions Max. 3.6 Unit V V V V 2, 3 Notes VREFOUT VREFOUT VREFOUT VSSA VSSA -- -- VDDA VDDA Table continues on the next page... K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. 44 Preliminary Freescale Semiconductor, Inc. Peripheral operating requirements and behaviors Table 26. 16-bit ADC with PGA operating conditions (continued) Symbol RPGAD Description Differntial input impedance Conditions Gain = 1, 2, 4, 8 Gain = 16, 32 Gain = 64 RAS TS Analog source resistance ADC sampling time Min. -- -- -- -- 1.25 Typ.1 128 64 32 100 -- Max. -- -- -- -- -- s 5 6 Unit k Notes IN+ to IN-4 1. Typical values assume VDDA = 3.0 V, Temp = 25C, fADCK = 6 MHz unless otherwise stated. Typical values are for reference only and are not tested in production. 2. ADC must be configured to use the internal voltage reference (VREFOUT) 3. PGA reference connected to the VREFOUT pin. If the user wishes to drive VREFOUT with a voltage other than the output of the VREF module, the VREF module must be disabled. 4. For single ended configurations the input impedence of the driven input is 1/2. 5. The analog source resistance (RAS), external to MCU, should be kept as minimum as possible. Increased RAS causes drop in PGA gain without affecting other performances. This is not dependent on ADC clock frequency. 6. The minimum sampling time is dependent on input signal frequency and ADC mode of operation. A minimum of 1.25s time should be allowed for Fin=4 kHz at 16-bit differential mode. Recommended ADC setting is: ADLSMP=1, ADLSTS=2 at 8 MHz ADC clock. 6.6.1.4 Symbol IDDA_PGA IDC_PGA IILKG G 16-bit ADC with PGA characteristics Description Supply current Input DC current Input Leakage current Gain4 PGA disabled * PGAG=0 * PGAG=1 * PGAG=2 * PGAG=3 * PGAG=4 * PGAG=5 * PGAG=6 -- TBD TBD TBD TBD TBD TBD TBD -- -- TBD Conditions Min. -- Table 27. 16-bit ADC with PGA characteristics Typ.1 590 Max. TBD Unit A A TBD 0.98 1.99 3.97 7.95 15.8 31.4 61.2 -- -- TBD TBD TBD TBD TBD TBD TBD TBD TBD 4 40 -- kHz kHz dB VDDA= 3V 100mV, fVDDA= 50Hz, 60Hz A 2 3 RAS < 100 Notes BW Input signal bandwidth Power supply rejection ration * 16-bit modes * < 16-bit modes Gain=1 PSRR Table continues on the next page... K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. Freescale Semiconductor, Inc. Preliminary 45 Peripheral operating requirements and behaviors Table 27. 16-bit ADC with PGA characteristics (continued) Symbol CMRR Description Common mode rejection ratio Conditions * Gain=1 * Gain=64 Min. TBD TBD Typ.1 TBD TBD Max. -- -- Unit dB dB Notes VCM= 500mVpp, fVCM= 50Hz, 100Hz Gain=1, ADC Averaging=32 5 0 to 50C VOFS TGSW dG/dT Input offset voltage Gain switching settling time Gain drift over temperature Offset drift over temperature Gain drift over supply voltage Input leakage error * Gain=1 * Gain=64 Gain=1 * Gain=1 * Gain=64 All modes -- -- -- -- -- -- -- 0.2 -- TBD TBD TBD TBD TBD IIn x RAS TBD 10 TBD TBD TBD TBD TBD mV s ppm/C ppm/C ppm/C %/V %/V mV dVOFS/dT dG/dVDDA EIL 0 to 50C, ADC Averaging=32 VDDA from 1.71 to 3.6V IIn = leakage current (refer to the MCU's voltage and current operating ratings) VPP,DIFF Maximum differential input signal swing Signal-to-noise ratio * Gain=1 * Gain=64 V where VX = VREFPGA x 0.583 TBD TBD 83.0 57.5 -- -- dB dB 6 SNR 16-bit differential mode, Average=32 16-bit differential mode, Average=32, fin=500Hz 16-bit differential mode, Average=32, fin=500Hz THD Total harmonic distortion * Gain=1 * Gain=64 TBD TBD 89.4 90.0 -- -- dB dB SFDR Spurious free dynamic range * Gain=1 * Gain=64 TBD TBD 90.9 77.0 -- -- dB dB Table continues on the next page... K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. 46 Preliminary Freescale Semiconductor, Inc. Peripheral operating requirements and behaviors Table 27. 16-bit ADC with PGA characteristics (continued) Symbol ENOB Description Effective number of bits Conditions * Gain=1, Average=4 * Gain=1, Average=8 * Gain=64, Average=4 * Gain=64, Average=8 * Gain=1, Average=32 * Gain=2, Average=32 * Gain=4, Average=32 * Gain=8, Average=32 * Gain=16, Average=32 * Gain=32, Average=32 * Gain=64, Average=32 SINAD Signal-to-noise plus distortion ratio See ENOB Min. TBD TBD TBD TBD TBD TBD TBD TBD TBD TBD TBD Typ.1 12.3 12.7 8.4 8.7 13.3 13.1 12.5 11.8 11.1 10.2 9.3 Max. -- -- -- -- -- -- -- -- -- -- -- Unit bits bits bits bits bits bits bits bits bits bits bits dB Notes 16-bit differential mode, fin=500Hz 6.02 x ENOB + 1.76 1. Typical values assume VDDA =3.0V, Temp=25C, fADCK=6MHz unless otherwise stated. 2. Between IN+ and IN-. The PGA draws a DC current from the input terminals. The magnitude of the DC current is a strong function if input common mode voltage (VCM) and the PGA gain. 3. This is the input leakage current of the module in addition to the PAD leakage current. 4. Gain = 2PGAG 5. When the PGA gain is changed, it takes some time to settle the output for the ADC to work properly. During a gain switching, a few ADC outputs should be discarded (minimum two data samples, may be more depending on ADC sampling rate and time of the switching). 6. Limit the input signal swing so that the PGA does not saturate during operation. Input signal swing is dependent on the PGA reference voltage and gain setting. 6.6.2 CMP and 6-bit DAC electrical specifications Table 28. Comparator and 6-bit DAC electrical specifications Symbol VDD IDDHS IDDLS VAIN VAIO Description Supply voltage Supply current, High-speed mode (EN=1, PMODE=1) Supply current, low-speed mode (EN=1, PMODE=0) Analog input voltage Analog input offset voltage Min. 1.71 -- -- VSS - 0.3 -- Table continues on the next page... Typ. -- -- -- -- -- Max. 3.6 200 20 VDD 20 Unit V A A V mV K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. Freescale Semiconductor, Inc. Preliminary 47 Peripheral operating requirements and behaviors Table 28. Comparator and 6-bit DAC electrical specifications (continued) Symbol VH Description Analog comparator hysteresis1 * CR0[HYSTCTR] = 00 * CR0[HYSTCTR] = 01 * CR0[HYSTCTR] = 10 * CR0[HYSTCTR] = 11 VCMPOh VCMPOl tDHS tDLS Output high Output low Propagation delay, high-speed mode (EN=1, PMODE=1) Propagation delay, low-speed mode (EN=1, PMODE=0) Analog comparator initialization delay2 IDAC6b INL DNL 6-bit DAC current adder (enabled) 6-bit DAC integral non-linearity 6-bit DAC differential non-linearity -- -- -- -- VDD - 0.5 -- 20 120 -- -- -0.5 -0.3 5 10 20 30 -- -- 50 250 -- 7 -- -- -- -- -- -- -- 0.5 200 600 TBD -- 0.5 0.3 mV mV mV mV V V ns ns ns A LSB3 LSB Min. Typ. Max. Unit 1. Typical hysteresis is measured with input voltage range limited to 0.6 to VDD-0.6V. 2. Comparator initialization delay is defined as the time between software writes to change control inputs (Writes to DACEN, VRSEL, PSEL, MSEL, VOSEL) and the comparator output settling to a stable level. 3. 1 LSB = Vreference/64 K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. 48 Preliminary Freescale Semiconductor, Inc. Peripheral operating requirements and behaviors 0.08 0.07 0.06 0.05 CM P Hystereris (V) HYSTCTR Setting 00 01 10 0.04 0.03 0.02 0.01 0 11 0.1 0.4 0.7 1 1.3 1.6 Vin level (V) 1.9 2.2 2.5 2.8 3.1 Figure 16. Typical hysteresis vs. Vin level (VDD=3.3V, PMODE=0) K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. Freescale Semiconductor, Inc. Preliminary 49 Peripheral operating requirements and behaviors 0.18 0.16 0.14 0.12 CMP Hystereris (V) P HYSTCTR Setting 00 01 10 11 0.1 0 08 0.08 0.06 0.04 0.02 0 0.1 0.4 0.7 1 1.3 Vin level (V) 1.6 1.9 2.2 2.5 2.8 3.1 Figure 17. Typical hysteresis vs. Vin level (VDD=3.3V, PMODE=1) 6.6.3 12-bit DAC electrical characteristics 6.6.3.1 Symbol VDDA VDACR TA CL IL 12-bit DAC operating requirements Desciption Supply voltage Reference voltage Temperature Output load capacitance Output load current Table 29. 12-bit DAC operating requirements Min. 1.71 1.13 -40 -- -- Max. 3.6 3.6 105 100 1 Unit V V C pF mA 2 1 Notes 1. The DAC reference can be selected to be VDDA or the voltage output of the VREF module (VREFO) 2. A small load capacitance (47 pF) can improve the bandwidth performance of the DAC K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. 50 Preliminary Freescale Semiconductor, Inc. Peripheral operating requirements and behaviors 6.6.3.2 Symbol 12-bit DAC operating behaviors Description Table 30. 12-bit DAC operating behaviors Min. -- -- -- -- -- 1 -- VDACR -100 -- -- -- 0.4 0.1 60 -- -- -- -- TBD TBD -- -- Typ. -- -- 100 15 -- TBD 100 -- -- -- -- -- -- Max. 150 700 200 30 5 -- TBD VDACR 8 1 1 0.8 0.6 90 -- -- TBD 250 Unit A A s s s s mV mV LSB LSB LSB %FSR %FSR dB V/C ppm of FSR/C V/yr V/s 1.2 0.05 -- 1.7 0.12 -- -- -- -80 dB kHz 550 40 -- -- -- -- 2 3 4 5 5 1 1 1 1 Notes IDDA_DACLP Supply current -- low-power mode IDDA_DACH Supply current -- high-speed mode P tDACLP tDACHP tCCDACLP tCCDACHP Vdacoutl Vdacouth INL DNL DNL VOFFSET EG PSRR TCO TGE AC Rop SR Full-scale settling time (0x080 to 0xF7F) -- lowpower mode Full-scale settling time (0x080 to 0xF7F) -- highpower mode Code-to-code settling time (0xBF8 to 0xC08) -- low-power mode Code-to-code settling time (0xBF8 to 0xC08) -- high-speed mode DAC output voltage range low -- high-speed mode, no load, DAC set to 0x000 DAC output voltage range high -- high-speed mode, no load, DAC set to 0xFFF Integral non-linearity error -- high speed mode Differential non-linearity error -- VDACR > 2 V Differential non-linearity error -- VDACR = VREFO (1.15 V) Offset error Gain error Power supply rejection ratio, VDDA > = 2.4 V Temperature coefficient offset voltage Temperature coefficient gain error Offset aging coefficient Output resistance load = 3 k Slew rate -80h F7Fh 80h * High power (SPHP) * Low power (SPLP) CT BW Channel to channel cross talk 3dB bandwidth * High power (SPHP) * Low power (SPLP) 1. 2. 3. 4. Settling within 1 LSB The INL is measured for 0+100mV to VDACR-100 mV The DNL is measured for 0+100 mV to VDACR-100 mV The DNL is measured for 0+100mV to VDACR-100 mV with VDDA > 2.4V K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. Freescale Semiconductor, Inc. Preliminary 51 Peripheral operating requirements and behaviors 5. Calculated by a best fit curve from VSS+100 mV to VREF-100 mV Figure 18. Typical INL error vs. digital code K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. 52 Preliminary Freescale Semiconductor, Inc. Peripheral operating requirements and behaviors Figure 19. Offset at half scale vs. temperature 6.6.4 Voltage reference electrical specifications Table 31. VREF full-range operating requirements Symbol VDDA TA CL Description Supply voltage Temperature Output load capacitance Min. 1.71 -40 -- Max. 3.6 105 100 Unit V C nF Notes Table 32. VREF full-range operating behaviors Symbol Vout Description Voltage reference output with factory trim at nominal VDDA and temperature=25C Min. TBD Typ. 1.2 Max. TBD Unit V Notes Table continues on the next page... K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. Freescale Semiconductor, Inc. Preliminary 53 Peripheral operating requirements and behaviors Table 32. VREF full-range operating behaviors (continued) Symbol Vout Vout Vstep Vdrift Ac Ibg Itr Description Voltage reference output with factory trim Voltage reference output user trim Voltage reference trim step Temperature drift (Vmax -Vmin across the full temperature range) Aging coefficient Bandgap only (MODE_LV = 00) current Tight-regulation buffer (MODE_LV =10) current Load regulation (MODE_LV = 10) current = 1.0mA Tstup DC Buffer startup time Line regulation (power supply rejection) Min. TBD 1.198 -- -- -- -- -- -- -- -- -60 Typ. -- -- 0.5 -- -- -- -- -- -- -- -- Max. TBD 1.202 -- 20 TBD TBD 1.1 TBD 100 TBD TBD Unit V V mV mV ppm/year A mA V s mV dB See Figure 20 Notes Table 33. VREF limited-range operating requirements Symbol TA Description Temperature Min. 0 Max. 50 Unit C Notes Table 34. VREF limited-range operating behaviors Symbol Vout Description Voltage reference output with factory trim Min. TBD Max. TBD Unit V Notes TBD Figure 20. Typical output vs.temperature TBD Figure 21. Typical output vs. VDD 6.7 Timers See General switching specifications. 6.8 Communication interfaces K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. 54 Preliminary Freescale Semiconductor, Inc. Peripheral operating requirements and behaviors 6.8.1 Ethernet switching specifications The following timing specs are defined at the chip I/O pin and must be translated appropriately to arrive at timing specs/constraints for the physical interface. 6.8.1.1 MII signal switching specifications The following timing specs meet the requirements for MII style interfaces for a range of transceiver devices. Table 35. MII signal switching specifications Symbol -- MII1 Description RXCLK frequency RXCLK pulse width high Min. -- 35% Max. 25 65% Unit MHz RXCLK period MII2 RXCLK pulse width low 35% 65% RXCLK period MII3 MII4 -- MII5 RXD[3:0], RXDV, RXER to RXCLK setup RXCLK to RXD[3:0], RXDV, RXER hold TXCLK frequency TXCLK pulse width high 5 5 -- 35% -- -- 25 65% ns ns MHz TXCLK period MII6 TXCLK pulse width low 35% 65% TXCLK period MII7 MII8 TXCLK to TXD[3:0], TXEN, TXER invalid TXCLK to TXD[3:0], TXEN, TXER valid 2 -- -- 25 ns ns MII6 MII5 TXCLK (input) MII8 MII7 Valid data TXD[n:0] TXEN Valid data TXER Valid data Figure 22. MII transmit signal timing diagram K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. Freescale Semiconductor, Inc. Preliminary 55 Peripheral operating requirements and behaviors MII2 MII1 RXCLK (input) MII3 MII4 RXD[n:0] Valid data RXDV Valid data RXER Valid data Figure 23. MII receive signal timing diagram 6.8.1.2 RMII signal switching specifications The following timing specs meet the requirements for RMII style interfaces for a range of transceiver devices. Table 36. RMII signal switching specifications Num -- RMII1 RMII2 RMII3 RMII4 RMII7 RMII8 Description EXTAL frequency (RMII input clock RMII_CLK) RMII_CLK pulse width high RMII_CLK pulse width low RXD[1:0], CRS_DV, RXER to RMII_CLK setup RMII_CLK to RXD[1:0], CRS_DV, RXER hold RMII_CLK to TXD[1:0], TXEN invalid RMII_CLK to TXD[1:0], TXEN valid Min. -- 35% 35% 4 2 4 -- Max. 50 65% 65% -- -- -- 15 Unit MHz RMII_CLK period RMII_CLK period ns ns ns ns 6.8.2 USB electrical specifications The USB electricals for the USB On-the-Go module conform to the standards documented by the Universal Serial Bus Implementers Forum. For the most up-to-date standards, visit http://www.usb.org. K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. 56 Preliminary Freescale Semiconductor, Inc. Peripheral operating requirements and behaviors 6.8.3 USB DCD electrical specifications Table 37. USB DCD electrical specifications Symbol VDP_SRC VLGC IDP_SRC IDM_SINK RDM_DWN VDAT_REF Description USB_DP source voltage (up to 250 A) Threshold voltage for logic high USB_DP source current USB_DM sink current D- pulldown resistance for data pin contact detect Data detect voltage Min. TBD 0.8 7 50 14.25 0.25 Typ. TBD -- 10 100 -- TBD Max. TBD 2.0 13 150 24.8 0.4 Unit V V A A k V 6.8.4 USB VREG electrical specifications Table 38. USB VREG electrical specifications Symbol VREGIN IDDon IDDstby IDDoff Description Input supply voltage Quiescent current -- Run mode, load current equal zero, input supply (VREGIN) > 3.6 V Quiescent current -- Standby mode, load current equal zero Quiescent current -- Shutdown mode * VREGIN = 5.0 V and temperature=25C * Across operating voltage and temperature ILOADrun ILOADstby VReg33out Maximum load current -- Run mode Maximum load current -- Standby mode Regulator output voltage -- Input supply (VREGIN) > 3.6 V * Run mode * Standby mode VReg33out COUT ESR ILIM Regulator output voltage -- Input supply (VREGIN) < 3.6 V, pass-through mode External output capacitor External output capacitor equivalent series resistance Current limitation threshold 3 2.5 2.3 1.76 1 185 3.3 2.8 -- 2.2 -- 290 3.6 3.6 3.6 8.16 100 395 V V V F m mA 1 -- -- -- -- 500 -- -- -- -- TBD 120 1 nA A mA mA Min. 2.7 -- -- Typ. -- 120 1 Max. 5.5 TBD TBD Unit V A A Notes 1. Operating in pass-through mode: regulator output voltage equal to the input voltage minus a drop proportional to ILoad. K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. Freescale Semiconductor, Inc. Preliminary 57 Peripheral operating requirements and behaviors 6.8.5 CAN switching specifications See General switching specifications. 6.8.6 DSPI switching specifications (low-speed mode) The DMA Serial Peripheral Interface (DSPI) provides a synchronous serial bus with master and slave operations. Many of the transfer attributes are programmable. The tables below provides DSPI timing characteristics for classic SPI timing modes. Refer to the DSPI chapter of the Reference Manual for information on the modified transfer formats used for communicating with slower peripheral devices. Table 39. Master mode DSPI timing (low-speed mode) Num Operating voltage Frequency of operation DS1 DS2 DS3 DS4 DS5 DS6 DS7 DS8 DSPI_SCK output cycle time DSPI_SCK output high/low time DSPI_PCSn to DSPI_SCK output valid DSPI_SCK to DSPI_PCSn output hold DSPI_SCK to DSPI_SOUT valid DSPI_SCK to DSPI_SOUT invalid DSPI_SIN to DSPI_SCK input setup DSPI_SCK to DSPI_SIN input hold Description Min. 1.71 -- 4 x tBCLK (tSCK/2) - 4 (tSCK/2) - 4 (tSCK/2) - 4 -- -2 15 0 Max. 3.6 12.5 -- (tSCK/2) + 4 -- -- 10 -- -- -- Unit V MHz ns ns ns ns ns ns ns ns Notes 1 1. The DSPI module can operate across the entire operating voltage for the processor, but to run across the full voltage range the maximum frequency of operation is reduced. DSPI_PCSn DS3 DS2 DS1 DS4 DSPI_SCK (CPOL=0) DSPI_SIN DS7 DS8 First data DS5 Data DS6 Data Last data DSPI_SOUT First data Last data Figure 24. DSPI classic SPI timing -- master mode K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. 58 Preliminary Freescale Semiconductor, Inc. Peripheral operating requirements and behaviors Table 40. Slave mode DSPI timing (low-speed mode) Num Operating voltage Frequency of operation DS9 DS10 DS11 DS12 DS13 DS14 DS15 DS16 DSPI_SCK input cycle time DSPI_SCK input high/low time DSPI_SCK to DSPI_SOUT valid DSPI_SCK to DSPI_SOUT invalid DSPI_SIN to DSPI_SCK input setup DSPI_SCK to DSIP_SIN input hold DSPI_SS active to DSPI_SOUT driven DSPI_SS inactive to DSPI_SOUT not driven Description Min. 1.71 -- 8 x tBCLK (tSCK/2) - 4 -- 0 5 15 -- -- Max. 3.6 6.25 -- (tSCK/2) + 4 20 -- -- -- 15 15 Unit V MHz ns ns ns ns ns ns ns ns DSPI_SS DS10 DS9 DSPI_SCK (CPOL=0) DSPI_SOUT DS13 DS15 DS12 First data DS14 First data Data Last data DS11 Data Last data DS16 DSPI_SIN Figure 25. DSPI classic SPI timing -- slave mode 6.8.7 DSPI switching specifications (high-speed mode) The DMA Serial Peripheral Interface (DSPI) provides a synchronous serial bus with master and slave operations. Many of the transfer attributes are programmable. The tables below provide DSPI timing characteristics for classic SPI timing modes. Refer to the DSPI chapter of the Reference Manual for information on the modified transfer formats used for communicating with slower peripheral devices. Table 41. Master mode DSPI timing (high-speed mode) Num Operating voltage Frequency of operation Table continues on the next page... Description Min. 2.7 -- Max. 3.6 25 Unit V MHz K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. Freescale Semiconductor, Inc. Preliminary 59 Peripheral operating requirements and behaviors Table 41. Master mode DSPI timing (high-speed mode) (continued) Num DS1 DS2 DS3 DS4 DS5 DS6 DS7 DS8 Description DSPI_SCK output cycle time DSPI_SCK output high/low time DSPI_PCSn to DSPI_SCK output valid DSPI_SCK to DSPI_PCSn output hold DSPI_SCK to DSPI_SOUT valid DSPI_SCK to DSPI_SOUT invalid DSPI_SIN to DSPI_SCK input setup DSPI_SCK to DSPI_SIN input hold Min. 2 x tBCLK (tSCK/2) - 2 (tSCK/2) - 2 (tSCK/2) - 2 -- -2 TBD 0 Max. -- (tSCK/2) + 2 -- -- 8.5 -- -- -- Unit ns ns ns ns ns ns ns ns DSPI_PCSn DS3 DS2 DS1 DS4 DSPI_SCK (CPOL=0) DSPI_SIN DS7 DS8 First data DS5 Data DS6 Data Last data DSPI_SOUT First data Last data Figure 26. DSPI classic SPI timing -- master mode Table 42. Slave mode DSPI timing (high-speed mode) Num Operating voltage Frequency of operation DS9 DS10 DS11 DS12 DS13 DS14 DS15 DS16 DSPI_SCK input cycle time DSPI_SCK input high/low time DSPI_SCK to DSPI_SOUT valid DSPI_SCK to DSPI_SOUT invalid DSPI_SIN to DSPI_SCK input setup DSPI_SCK to DSIP_SIN input hold DSPI_SS active to DSPI_SOUT driven DSPI_SS inactive to DSPI_SOUT not driven 4 x tBCLK (tSCK/2) - 2 -- 0 2 7 -- -- Description Min. 2.7 Max. 3.6 12.5 -- (tSCK/2 + 2 TBD -- -- -- 14 14 Unit V MHz ns ns ns ns ns ns ns ns K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. 60 Preliminary Freescale Semiconductor, Inc. Peripheral operating requirements and behaviors DSPI_SS DS10 DS9 DSPI_SCK (CPOL=0) DSPI_SOUT DS13 DS15 DS12 First data DS14 First data Data Last data DS11 Data Last data DS16 DSPI_SIN Figure 27. DSPI classic SPI timing -- slave mode 6.8.8 I2C switching specifications See General switching specifications. 6.8.9 UART switching specifications See General switching specifications. 6.8.10 SDHC specifications The following timing specs are defined at the chip I/O pin and must be translated appropriately to arrive at timing specs/constraints for the physical interface. Table 43. SDHC switching specifications Num Symbol Description Operating voltage Card input clock SD1 fpp fpp fpp fOD SD2 SD3 SD4 tWL tWH tTLH Clock frequency (low speed) Clock frequency (SD\SDIO full speed) Clock frequency (MMC full speed) Clock frequency (identification mode) Clock low time Clock high time Clock rise time Table continues on the next page... 0 0 0 0 7 7 -- 400 25 20 400 -- -- 3 kHz MHz MHz kHz ns ns ns Min. 2.7 Max. 3.6 Unit V K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. Freescale Semiconductor, Inc. Preliminary 61 Peripheral operating requirements and behaviors Table 43. SDHC switching specifications (continued) Num SD5 Symbol tTHL Description Clock fall time Min. -- Max. 3 Unit ns SDHC output / card inputs SDHC_CMD, SDHC_DAT (reference to SDHC_CLK) SD6 tOD SDHC output delay (output valid) -5 6.5 ns SDHC input / card inputs SDHC_CMD, SDHC_DAT (reference to SDHC_CLK) SD7 SD8 tTHL tTHL SDHC input setup time SDHC input hold time 5 0 -- -- ns ns SD3 SD2 SD1 SDHC_CLK SD6 Output SDHC_CMD Output SDHC_DAT[3:0] SD7 SD8 Input SDHC_CMD Input SDHC_DAT[3:0] Figure 28. SDHC timing 6.8.11 I2S switching specifications This section provides the AC timings for the I2S in master (clocks driven) and slave modes (clocks input). All timings are given for non-inverted serial clock polarity (TCR[TSCKP] = 0, RCR[RSCKP] = 0) and a non-inverted frame sync (TCR[TFSI] = 0, RCR[RFSI] = 0). If the polarity of the clock and/or the frame sync have been inverted, all the timings remain valid by inverting the clock signal (I2S_BCLK) and/or the frame sync (I2S_FS) shown in the figures below. Table 44. I2S master mode timing Num Description Operating voltage S1 I2S_MCLK cycle time Table continues on the next page... Min. 2.7 2 x tSYS Max. 3.6 Unit V ns K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. 62 Preliminary Freescale Semiconductor, Inc. Peripheral operating requirements and behaviors Table 44. I2S master mode timing (continued) Num S2 S3 S4 S5 S6 S7 S8 S9 S10 Description I2S_MCLK pulse width high/low I2S_BCLK cycle time I2S_BCLK pulse width high/low I2S_BCLK to I2S_FS output valid I2S_BCLK to I2S_FS output invalid I2S_BCLK to I2S_TXD valid I2S_BCLK to I2S_TXD invalid I2S_RXD/I2S_FS input setup before I2S_BCLK I2S_RXD/I2S_FS input hold after I2S_BCLK Min. 45% 5 x tSYS 45% -- -2.5 -- -3 20 0 Max. 55% -- 55% 15 -- 15 -- -- -- Unit MCLK period ns BCLK period ns ns ns ns ns ns S1 S2 S2 I2S_MCLK (output) S3 I2S_BCLK (output) S4 S5 S4 S6 I2S_FS (output) S9 S10 I2S_FS (input) S7 S8 S7 S8 I2S_TXD S9 S10 I2S_RXD Figure 29. I2S timing -- master mode Table 45. I2S slave mode timing Num Description Operating voltage S11 S12 S13 S14 S15 S16 S17 I2S_BCLK cycle time (input) I2S_BCLK pulse width high/low (input) I2S_FS input setup before I2S_BCLK I2S_FS input hold after I2S_BCLK I2S_BCLK to I2S_TXD/I2S_FS output valid I2S_BCLK to I2S_TXD/I2S_FS output invalid I2S_RXD setup before I2S_BCLK Table continues on the next page... Min. 2.7 8 x tSYS 45% 10 3 -- 0 10 Max. 3.6 -- 55% -- -- 20 -- -- Unit V ns MCLK period ns ns ns ns ns K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. Freescale Semiconductor, Inc. Preliminary 63 Peripheral operating requirements and behaviors Table 45. I2S slave mode timing (continued) Num S18 Description I2S_RXD hold after I2S_BCLK Min. 2 Max. -- Unit ns S11 S12 I2S_BCLK (input) S15 S12 S16 I2S_FS (output) S13 S14 I2S_FS (input) S15 S16 S15 S16 I2S_TXD S17 S18 I2S_RXD Figure 30. I2S timing -- slave modes 6.9 Human-machine interfaces (HMI) 6.9.1 TSI electrical specifications Table 46. TSI electrical specifications Symbol VDDTSI CELE fREFmax fELEmax CREF VDELTA IREF IELE Pres5 Pres20 Pres100 Description Operating voltage Target electrode capacitance range Reference oscillator frequency Electrode oscillator frequency Internal reference capacitor Oscillator delta voltage Reference oscillator current source base current Electrode oscillator current source base current Electrode capacitance measurement precision Electrode capacitance measurement precision Electrode capacitance measurement precision Min. 1.71 1 -- -- TBD TBD TBD TBD -- -- -- Typ. -- 20 5.5 0.5 1 600 1 1 TBD TBD TBD Max. 3.6 500 TBD TBD TBD TBD TBD TBD TBD TBD TBD Unit V pF MHz MHz pF mV A A % % % 2 2 3 4 5 1 Notes Table continues on the next page... K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. 64 Preliminary Freescale Semiconductor, Inc. Dimensions Table 46. TSI electrical specifications (continued) Symbol Description Min. 0.003 0.003 -- 8 -- -- Typ. 0.25 -- -- 15 TBD 1 Max. -- -- 16 25 -- TBD Unit fF/count fF/count bits s A A 8 Notes 6 7 MaxSens2 Maximum sensitivity @ 20 pF electrode 0 MaxSens Res TCon20 ITSI_RUN ITSI_LP 1. 2. 3. 4. 5. 6. Maximum sensitivity Resolution Response time @ 20 pF Current added in run mode Low power mode current adder The TSI module is functional with capacitance values outside this range. However, optimal performance is not guaranteed. The programmable current source value is generated by multiplying the SCANC[REFCHRG] value and the base current. Measured with a 5 pF electrode, reference oscillator frequency of 10 MHz, PS = 128, NSCN = 8; Iext = 16. Measured with a 20 pF electrode, reference oscillator frequency of 10 MHz, PS = 128, NSCN = 2; Iext = 16. Measured with a 20 pF electrode, reference oscillator frequency of 10 MHz, PS = 16, NSCN = 3; Iext = 16. Measured with a 20 pF electrode, reference oscillator frequency of ~5 MHz (IREF = 5 A, REFCHRG = 4), PS = 128, NSCN = 2; Iext = 16 (EXTCHRG = 15). 7. Typical value depends on the configuration used. 8. Time to do one complete measurement of the electrode. Sensitivity resolution of 0.0133 pF, PS = 0, NSCN = 0, 1 electrode, DELVOL = 2, EXTCHRG = 15. 7 Dimensions 7.1 Obtaining package dimensions Package dimensions are provided in package drawings. To find a package drawing, go to http://www.freescale.com and perform a keyword search for the drawing's document number: If you want the drawing for this package 80-pin LQFP 81-pin MAPBGA 144-pin LQFP 144-pin MAPBGA Then use this document number 98ASS23174W 98ASA10631D 98ASS23177W 98ASA00222D 8 Pinout K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. Freescale Semiconductor, Inc. Preliminary 65 Pinout 8.1 K60 Signal Multiplexing and Pin Assignments The following table shows the signals available on each pin and the locations of these pins on the devices supported by this document. The Port Control Module is responsible for selecting which ALT functionality is available on each pin. NOTE The 81-pin ballmap assignments are currently being developed. The * in the entries in this package column indicate which signals are present on the package. 144 144 LQF MAP P BGA -- -- -- -- -- 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 L5 M5 Pin Name Default ALT0 ALT1 ALT2 ALT3 ALT4 ALT5 ALT6 ALT7 EzPort NC NC NC NC NC NC NC ADC1_SE4 a ADC1_SE5 a ADC1_SE6 a ADC1_SE7 a VDD VSS DISABLED DISABLED DISABLED DISABLED DISABLED DISABLED DISABLED DISABLED DISABLED VDD VSS VSS NC NC NC NC NC ADC1_SE4 a ADC1_SE5 a ADC1_SE6 a ADC1_SE7 a VDD VSS PTE4 PTE5 PTE6 PTE7 PTE8 PTE9 PTE10 PTE11 PTE12 VDD VSS VSS SPI1_PCS0 UART3_TX SPI1_PCS2 UART3_RX SPI1_PCS3 UART3_CT S_b UART3_RT S_b SDHC0_D3 SDHC0_D2 I2S0_MCLK I2S0_RXD I2S0_RX_F S I2S0_RX_B CLK I2S0_TXD I2S0_TX_F S I2S0_TX_B CLK I2S0_CLKIN PTE0 PTE1 PTE2 PTE3 SPI1_PCS1 UART1_TX SPI1_SOUT UART1_RX SPI1_SCK SPI1_SIN UART1_CT S_b UART1_RT S_b SDHC0_D1 SDHC0_D0 SDHC0_DC LK SDHC0_CM D I2C1_SDA I2C1_SCL A10 NC B10 NC C10 NC D3 D2 D1 E4 E5 F6 E3 E2 E1 F4 F3 F2 F1 G4 G3 E6 F7 H3 PTE0 PTE1 PTE2 PTE3 VDD VSS PTE4 PTE5 PTE6 PTE7 PTE8 PTE9 PTE10 PTE11 PTE12 VDD VSS VSS K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. 66 Preliminary Freescale Semiconductor, Inc. Pinout 144 144 LQF MAP P BGA 19 20 21 22 23 24 25 26 27 H1 H2 G1 G2 J1 J2 K1 K2 L1 Pin Name Default ALT0 ALT1 ALT2 ALT3 ALT4 ALT5 ALT6 ALT7 EzPort USB0_DP USB0_DM VOUT33 VREGIN ADC0_DP1 ADC1_DP1 USB0_DP USB0_DM VOUT33 VREGIN ADC0_DP1 ADC1_DP1 USB0_DP USB0_DM VOUT33 VREGIN ADC0_DP1 ADC1_DP1 ADC0_DM1 ADC0_DM1 ADC0_DM1 ADC1_DM1 ADC1_DM1 ADC1_DM1 PGA0_DP/ PGA0_DP/ PGA0_DP/ ADC0_DP0/ ADC0_DP0/ ADC0_DP0/ ADC1_DP3 ADC1_DP3 ADC1_DP3 PGA0_DM/ PGA0_DM/ PGA0_DM/ ADC0_DM0/ ADC0_DM0/ ADC0_DM0/ ADC1_DM3 ADC1_DM3 ADC1_DM3 PGA1_DP/ PGA1_DP/ PGA1_DP/ ADC1_DP0/ ADC1_DP0/ ADC1_DP0/ ADC0_DP3 ADC0_DP3 ADC0_DP3 PGA1_DM/ PGA1_DM/ PGA1_DM/ ADC1_DM0/ ADC1_DM0/ ADC1_DM0/ ADC0_DM3 ADC0_DM3 ADC0_DM3 VDDA VREFH VREFL VSSA ADC1_SE1 6/ CMP2_IN2/ ADC0_SE2 2 ADC0_SE1 6/ CMP1_IN2/ ADC0_SE2 1 VDDA VREFH VREFL VSSA ADC1_SE1 6/ CMP2_IN2/ ADC0_SE2 2 ADC0_SE1 6/ CMP1_IN2/ ADC0_SE2 1 VDDA VREFH VREFL VSSA ADC1_SE1 6/ CMP2_IN2/ ADC0_SE2 2 ADC0_SE1 6/ CMP1_IN2/ ADC0_SE2 1 28 L2 29 M1 30 M2 31 32 33 34 35 H5 G5 G6 H6 K3 36 J3 37 M3 VREF_OUT/ VREF_OUT VREF_OUT/ CMP1_IN5/ CMP1_IN5/ CMP0_IN5/ CMP0_IN5/ ADC1_SE1 ADC1_SE1 8 8 DAC0_OUT/ DAC0_OUT DAC0_OUT/ CMP1_IN3/ CMP1_IN3/ ADC0_SE2 ADC0_SE2 3 3 DAC1_OUT/ DAC1_OUT DAC1_OUT/ CMP2_IN3/ CMP2_IN3/ ADC1_SE2 ADC1_SE2 3 3 XTAL32 XTAL32 XTAL32 38 L3 39 L4 40 M7 K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. Freescale Semiconductor, Inc. Preliminary 67 Pinout 144 144 LQF MAP P BGA 41 42 43 44 45 46 47 48 49 50 M6 L6 -- -- M4 K5 K4 J4 H4 J5 Pin Name Default ALT0 ALT1 ALT2 ALT3 ALT4 ALT5 ALT6 ALT7 EzPort EXTAL32 VBAT VDD VSS PTE24 PTE25 PTE26 PTE27 PTE28 PTA0 EXTAL32 VBAT VDD VSS ADC0_SE1 7 ADC0_SE1 8 DISABLED DISABLED DISABLED JTAG_TCL K/ SWD_CLK/ EZP_CLK JTAG_TDI/ EZP_DI EXTAL32 VBAT VDD VSS ADC0_SE1 7 ADC0_SE1 8 PTE24 PTE25 PTE26 PTE27 PTE28 TSI0_CH1 PTA0 UART0_CT S_b FTM0_CH5 JTAG_TCL K/ SWD_CLK JTAG_TDI EZP_CLK CAN1_TX CAN1_RX UART4_TX UART4_RX UART4_CT S_b UART4_RT S_b ENET_1588 _CLKIN EWM_OUT _b EWM_IN RTC_CLKO USB_CLKIN UT 51 52 J6 K6 PTA1 PTA2 TSI0_CH2 PTA1 PTA2 UART0_RX UART0_TX FTM0_CH6 FTM0_CH7 EZP_DI JTAG_TDO/ TSI0_CH3 TRACE_SW O/EZP_DO JTAG_TMS/ TSI0_CH4 SWD_DIO NMI_b/ EZP_CS_b DISABLED TSI0_CH5 JTAG_TDO/ EZP_DO TRACE_SW O JTAG_TMS/ SWD_DIO NMI_b RMII0_RXE CMP2_OUT I2S0_RX_B R/ CLK MII0_RXER JTAG_TRS T EZP_CS_b 53 54 55 K7 L7 M8 PTA3 PTA4 PTA5 PTA3 PTA4 PTA5 UART0_RT S_b FTM0_CH0 FTM0_CH1 FTM0_CH2 56 57 58 59 60 61 62 63 64 E7 G7 J7 J8 K8 L8 M9 L9 K9 VDD VSS PTA6 PTA7 PTA8 PTA9 PTA10 PTA11 PTA12 VDD VSS DISABLED ADC0_SE1 0 ADC0_SE1 1 DISABLED DISABLED DISABLED CMP2_IN0 VDD VSS PTA6 ADC0_SE1 0 ADC0_SE1 1 PTA7 PTA8 PTA9 PTA10 PTA11 CMP2_IN0 PTA12 CAN0_TX FTM0_CH3 FTM0_CH4 FTM1_CH0 FTM1_CH1 FTM2_CH0 FTM2_CH1 FTM1_CH0 MII0_RXD3 MII0_RXD2 MII0_RXCL K RMII0_RXD 1/ MII0_RXD1 FTM1_QD_ PHA FTM1_QD_ PHB FTM2_QD_ PHA FTM2_QD_ PHB I2S0_TXD FTM1_QD_ PHA TRACE_CL KOUT TRACE_D3 TRACE_D2 TRACE_D1 TRACE_D0 K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. 68 Preliminary Freescale Semiconductor, Inc. Pinout 144 144 LQF MAP P BGA 65 J9 Pin Name Default ALT0 ALT1 ALT2 ALT3 ALT4 ALT5 ALT6 ALT7 EzPort PTA13 CMP2_IN1 CMP2_IN1 PTA13 CAN0_RX FTM1_CH1 RMII0_RXD 0/ MII0_RXD0 RMII0_CRS _DV/ MII0_RXDV RMII0_TXE N/ MII0_TXEN RMII0_TXD 0/ MII0_TXD0 RMII0_TXD 1/ MII0_TXD1 I2S0_TX_F S I2S0_TX_B CLK I2S0_RXD FTM1_QD_ PHB 66 L10 PTA14 DISABLED PTA14 SPI0_PCS0 UART0_TX 67 L11 PTA15 DISABLED PTA15 SPI0_SCK UART0_RX 68 K10 PTA16 DISABLED PTA16 SPI0_SOUT UART0_CT S_b SPI0_SIN UART0_RT S_b I2S0_RX_F S I2S0_MCLK I2S0_CLKIN 69 K11 PTA17 ADC1_SE1 7 VDD VSS EXTAL XTAL RESET_b DISABLED DISABLED DISABLED DISABLED DISABLED DISABLED / ADC0_SE8/ ADC1_SE8/ TSI0_CH0 / ADC0_SE9/ ADC1_SE9/ TSI0_CH6 ADC1_SE1 7 VDD VSS EXTAL XTAL RESET_b PTA17 70 71 72 73 74 75 76 77 78 79 80 81 E8 G8 VDD VSS M12 PTA18 M11 PTA19 L12 RESET_b K12 PTA24 J12 J11 J10 PTA25 PTA26 PTA27 PTA18 PTA19 FTM0_FLT2 FTM_CLKIN 0 FTM1_FLT0 FTM_CLKIN 1 MII0_TXD2 MII0_TXCL K MII0_TXD3 MII0_CRS MII0_TXER MII0_COL I2C0_SCL FTM1_CH0 RMII0_MDI O/ MII0_MDIO RMII0_MDC /MII0_MDC LPT0_ALT1 PTA24 PTA25 PTA26 PTA27 PTA28 PTA29 / PTB0 ADC0_SE8/ ADC1_SE8/ TSI0_CH0 / PTB1 ADC0_SE9/ ADC1_SE9/ TSI0_CH6 FB_A29 FB_A28 FB_A27 FB_A26 FB_A25 FB_A24 FTM1_QD_ PHA H12 PTA28 H11 PTA29 H10 PTB0 82 H9 PTB1 I2C0_SDA FTM1_CH1 FTM1_QD_ PHB 83 G12 PTB2 / / PTB2 ADC0_SE1 ADC0_SE1 2/TSI0_CH7 2/TSI0_CH7 / / PTB3 ADC0_SE1 ADC0_SE1 3/TSI0_CH8 3/TSI0_CH8 / ADC1_SE1 0 / ADC1_SE1 0 PTB4 I2C0_SCL UART0_RT S_b UART0_CT S_b ENET0_158 8_TMR0 ENET0_158 8_TMR1 ENET0_158 8_TMR2 FTM0_FLT3 84 G11 PTB3 I2C0_SDA FTM0_FLT0 85 G10 PTB4 FTM1_FLT0 K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. Freescale Semiconductor, Inc. Preliminary 69 Pinout 144 144 LQF MAP P BGA 86 G9 Pin Name Default ALT0 ALT1 ALT2 ALT3 ALT4 ALT5 ALT6 ALT7 EzPort PTB5 / ADC1_SE1 1 / ADC1_SE1 2 / ADC1_SE1 3 / ADC1_SE1 1 / ADC1_SE1 2 / ADC1_SE1 3 PTB5 ENET0_158 8_TMR3 FB_AD23 FTM2_FLT0 87 F12 PTB6 PTB6 88 F11 PTB7 PTB7 FB_AD22 89 90 91 F10 PTB8 F9 PTB9 / ADC1_SE1 4 / ADC1_SE1 5 VSS VDD /TSI0_CH9 / ADC1_SE1 4 / ADC1_SE1 5 VSS VDD /TSI0_CH9 PTB8 PTB9 PTB10 UART3_RT S_b SPI1_PCS1 UART3_CT S_b SPI1_PCS0 UART3_RX FB_AD21 FB_AD20 FB_AD19 FTM0_FLT1 E12 PTB10 92 E11 PTB11 PTB11 SPI1_SCK UART3_TX FB_AD18 FTM0_FLT2 93 94 95 96 97 98 99 100 101 102 103 H7 F5 E9 VSS VDD PTB17 E10 PTB16 PTB16 SPI1_SOUT UART0_RX SPI1_SIN CAN0_TX CAN0_RX SPI2_PCS0 SPI2_SCK SPI2_SOUT SPI2_SIN SPI0_PCS5 I2S0_TXD SPI0_PCS4 PDB0_EXT RG UART0_TX FTM2_CH0 FTM2_CH1 I2S0_TX_B CLK I2S0_TX_F S FB_AD17 FB_AD16 FB_AD15 FB_OE_b FB_AD31 FB_AD30 FB_AD29 FB_AD28 FB_AD14 EWM_IN EWM_OUT _b FTM2_QD_ PHA FTM2_QD_ PHB CMP0_OUT CMP1_OUT CMP2_OUT /TSI0_CH10 /TSI0_CH10 PTB17 /TSI0_CH11 /TSI0_CH11 PTB18 /TSI0_CH12 /TSI0_CH12 PTB19 PTB20 PTB21 PTB22 PTB23 / ADC0_SE1 4/ TSI0_CH13 / ADC0_SE1 5/ TSI0_CH14 / ADC0_SE4 b/ CMP1_IN0/ TSI0_CH15 /CMP1_IN1 VSS / ADC0_SE1 4/ TSI0_CH13 / ADC0_SE1 5/ TSI0_CH14 / ADC0_SE4 b/ CMP1_IN0/ TSI0_CH15 /CMP1_IN1 VSS PTC0 D12 PTB18 D11 PTB19 D10 PTB20 D9 PTB21 C12 PTB22 C11 PTB23 B12 PTC0 104 B11 PTC1 PTC1 SPI0_PCS3 UART1_RT S_b FTM0_CH0 FB_AD13 105 A12 PTC2 PTC2 SPI0_PCS2 UART1_CT S_b FTM0_CH1 FB_AD12 106 107 A11 PTC3 H8 VSS PTC3 SPI0_PCS1 UART1_RX FTM0_CH2 FB_CLKOU T K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. 70 Preliminary Freescale Semiconductor, Inc. Pinout 144 144 LQF MAP P BGA 108 109 110 111 112 113 -- A9 D8 C8 B8 A8 Pin Name Default ALT0 ALT1 ALT2 ALT3 ALT4 ALT5 ALT6 ALT7 EzPort VDD PTC4 PTC5 PTC6 PTC7 PTC8 VDD VDD PTC4 PTC5 SPI0_PCS0 UART1_TX SPI0_SCK SPI0_SOUT PDB0_EXT RG SPI0_SIN FTM0_CH3 FB_AD11 FB_AD9 FB_AD8 I2S0_MCLK I2S0_CLKIN FB_AD7 CMP1_OUT CMP0_OUT LPT0_ALT2 FB_AD10 /CMP0_IN0 /CMP0_IN1 / ADC1_SE4 b/ CMP0_IN2 / ADC1_SE5 b/ CMP0_IN3 / ADC1_SE6 b/ CMP0_IN4 / ADC1_SE7 b /CMP0_IN0 /CMP0_IN1 / ADC1_SE4 b/ CMP0_IN2 / ADC1_SE5 b/ CMP0_IN3 / ADC1_SE6 b/ CMP0_IN4 / ADC1_SE7 b PTC6 PTC7 PTC8 114 D7 PTC9 PTC9 I2S0_RX_B CLK FB_AD6 FTM2_FLT0 115 C7 PTC10 PTC10 I2C1_SCL I2S0_RX_F S FB_AD5 116 B7 PTC11 PTC11 I2C1_SDA I2S0_RXD FB_RW_b 117 118 119 120 121 122 123 A7 D6 C6 B6 -- -- A6 PTC12 PTC13 PTC14 PTC15 VSS VDD PTC16 VSS VDD VSS VDD PTC12 PTC13 PTC14 PTC15 UART4_RT S_b UART4_CT S_b UART4_RX UART4_TX FB_AD27 FB_AD26 FB_AD25 FB_AD24 PTC16 CAN1_RX UART3_RX ENET0_158 FB_CS5_b/ 8_TMR0 FB_TSIZ1/ FB_BE23_1 6_BLS15_8 _b ENET0_158 FB_CS4_b/ 8_TMR1 FB_TSIZ0/ FB_BE31_2 4_BLS7_0_ b ENET0_158 FB_TBST_b 8_TMR2 /FB_CS2_b/ FB_BE15_8 _BLS23_16 _b ENET0_158 FB_CS3_b/ FB_TA_b 8_TMR3 FB_BE7_0_ BLS31_24_ b 124 D5 PTC17 PTC17 CAN1_TX UART3_TX 125 C5 PTC18 PTC18 UART3_RT S_b 126 B5 PTC19 PTC19 UART3_CT S_b K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. Freescale Semiconductor, Inc. Preliminary 71 Pinout 144 144 LQF MAP P BGA 127 A5 Pin Name Default ALT0 ALT1 ALT2 ALT3 ALT4 ALT5 ALT6 ALT7 EzPort PTD0 PTD0 SPI0_PCS0 UART2_RT S_b SPI0_SCK UART2_CT S_b FB_ALE/ FB_CS1_b/ FB_TS_b FB_CS0_b 128 D4 PTD1 / ADC0_SE5 b / ADC0_SE5 b PTD1 129 130 131 132 C4 B4 A4 A3 PTD2 PTD3 PTD4 PTD5 / ADC0_SE6 b / ADC0_SE7 b VSS VDD DISABLED DISABLED DISABLED DISABLED DISABLED DISABLED DISABLED DISABLED / ADC0_SE6 b / ADC0_SE7 b VSS VDD PTD2 PTD3 PTD4 PTD5 SPI0_SOUT UART2_RX SPI0_SIN UART2_TX FTM0_CH4 FTM0_CH5 SPI0_PCS1 UART0_RT S_b SPI0_PCS2 UART0_CT S_b SPI0_PCS3 UART0_RX FB_AD4 FB_AD3 FB_AD2 FB_AD1 EWM_IN EWM_OUT _b FTM0_FLT0 133 A2 PTD6 PTD6 FTM0_CH6 FB_AD0 134 135 136 137 138 139 140 141 142 143 144 M10 VSS F8 A1 C9 B9 B3 B2 B1 C3 C2 C1 VDD PTD7 PTD8 PTD9 PTD10 PTD11 PTD12 PTD13 PTD14 PTD15 PTD7 PTD8 PTD9 PTD10 PTD11 PTD12 PTD13 PTD14 PTD15 CMT_IRO I2C0_SCL I2C0_SDA SPI2_PCS0 SPI2_SCK SPI2_SOUT SPI2_SIN SPI2_PCS1 UART0_TX FTM0_CH7 FTM0_FLT1 FB_A16 FB_A17 FB_A18 SDHC0_CL KIN SDHC0_D4 SDHC0_D5 SDHC0_D6 SDHC0_D7 FB_A19 FB_A20 FB_A21 FB_A22 FB_A23 8.2 K60 Pinouts The below figure shows the pinout diagram for the devices supported by this document. Many signals may be multiplexed onto a single pin. To determine what signals can be used on which pin, see the previous section. K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. 72 Preliminary Freescale Semiconductor, Inc. Pinout PTD15 PTD14 PTD13 PTD12 PTD11 PTD10 PTC19 PTC18 PTC17 PTC16 PTC15 PTC14 PTC13 PTC12 PTC11 PTC10 PTD9 PTD8 PTD7 PTD6 PTD5 PTD4 PTD3 PTD2 PTD1 PTD0 PTC9 PTC8 PTC7 PTC6 111 PTC5 110 PTC4 109 108 106 105 104 103 102 101 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 37 38 39 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 VDD VDD 122 VSS VSS 121 141 142 132 131 139 135 129 125 119 138 136 128 126 140 130 144 143 137 134 133 127 124 123 120 118 117 116 115 114 PTE0 PTE1 PTE2 PTE3 VDD VSS PTE4 PTE5 PTE6 PTE7 PTE8 PTE9 PTE10 PTE11 PTE12 VDD VSS VSS USB0_DP USB0_DM VOUT33 VREGIN ADC0_DP1 ADC0_DM1 ADC1_DP1 ADC1_DM1 PGA0_DP/ADC0_DP0/ADC1_DP3 PGA0_DM/ADC0_DM0/ADC1_DM3 PGA1_DP/ADC1_DP0/ADC0_DP3 PGA1_DM/ADC1_DM0/ADC0_DM3 VDDA VREFH VREFL VSSA ADC1_SE16/CMP2_IN2/ADC0_SE22 ADC0_SE16/CMP1_IN2/ADC0_SE21 113 112 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 VDD VSS PTC3 PTC2 PTC1 PTC0 PTB23 PTB22 PTB21 PTB20 PTB19 PTB18 PTB17 PTB16 VDD VSS PTB11 PTB10 PTB9 PTB8 PTB7 PTB6 PTB5 PTB4 PTB3 PTB2 PTB1 PTB0 PTA29 PTA28 PTA27 PTA26 PTA25 PTA24 RESET_b PTA19 107 PTA1 EXTAL32 PTA9 VSS PTE24 PTA10 DAC1_OUT/CMP2_IN3/ADC1_SE23 PTE28 PTA13 PTE25 DAC0_OUT/CMP1_IN3/ADC0_SE23 PTE27 PTA14 XTAL32 PTA16 PTA17 VREF_OUT/CMP1_IN5/CMP0_IN5/ADC1_SE18 PTE26 PTA11 PTA12 Figure 31. K60 144 LQFP Pinout Diagram K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. Freescale Semiconductor, Inc. Preliminary PTA15 PTA18 VBAT PTA2 PTA5 PTA6 PTA7 VDD PTA0 PTA3 PTA4 PTA8 VDD VDD VSS VSS 73 Revision History 1 2 3 4 5 6 7 8 9 10 11 12 A PTD7 PTD6 PTD5 PTD4 PTD0 PTC16 PTC12 PTC8 PTC4 NC PTC3 PTC2 A B PTD12 PTD11 PTD10 PTD3 PTC19 PTC15 PTC11 PTC7 PTD9 NC PTC1 PTC0 B C PTD15 PTD14 PTD13 PTD2 PTC18 PTC14 PTC10 PTC6 PTD8 NC PTB23 PTB22 C D PTE2 PTE1 PTE0 PTD1 PTC17 PTC13 PTC9 PTC5 PTB21 PTB20 PTB19 PTB18 D E PTE6 PTE5 PTE4 PTE3 VDD VDD VDD VDD PTB17 PTB16 PTB11 PTB10 E F PTE10 PTE9 PTE8 PTE7 VDD VSS VSS VDD PTB9 PTB8 PTB7 PTB6 F G VOUT33 VREGIN PTE12 PTE11 VREFH VREFL VSS VSS PTB5 PTB4 PTB3 PTB2 G H USB0_DP USB0_DM VSS PTE28 VDDA VSSA VSS VSS PTB1 PTB0 PTA29 PTA28 H J ADC0_DP1 ADC0_DM1 ADC0_SE16/ CMP1_IN2/ ADC0_SE21 PTE27 PTA0 PTA1 PTA6 PTA7 PTA13 PTA27 PTA26 PTA25 J K ADC1_DP1 ADC1_DM1 ADC1_SE16/ CMP2_IN2/ ADC0_SE22 PTE26 PTE25 PTA2 PTA3 PTA8 PTA12 PTA16 PTA17 PTA24 K L PGA0_DP/ ADC0_DP0/ ADC1_DP3 PGA0_DM/ ADC0_DM0/ ADC1_DM3 DAC0_OUT/ CMP1_IN3/ ADC0_SE23 VREF_OUT/ CMP1_IN5/ CMP0_IN5/ ADC1_SE18 3 DAC1_OUT/ CMP2_IN3/ ADC1_SE23 NC VBAT PTA4 PTA9 PTA11 PTA14 PTA15 RESET_b L PGA1_DP/ M ADC1_DP0/ ADC0_DP3 1 PGA1_DM/ ADC1_DM0/ ADC0_DM3 2 PTE24 NC EXTAL32 XTAL32 PTA5 PTA10 VSS PTA19 PTA18 M 4 5 6 7 8 9 10 11 12 Figure 32. K60 144 MAPBGA Pinout Diagram 9 Revision History The following table provides a revision history for this document. Table 47. Revision History Rev. No. 1 Date 11/2010 Substantial Changes Initial public revision Table continues on the next page... K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. 74 Preliminary Freescale Semiconductor, Inc. Revision History Table 47. Revision History (continued) Rev. No. 2 Date 3/2011 Substantial Changes Many updates throughout Corrected 81- and 104-pin package codes 3 4 3/2011 3/2011 Added sections that were inadvertently removed in previous revision Reworded IIC footnote in "Voltage and Current Operating Requirements" table. Added paragraph to "Peripheral operating requirements and behaviors" section. Added "JTAG full voltage range electricals" table to the "JTAG electricals" section. K60 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011. Freescale Semiconductor, Inc. Preliminary 75 How to Reach Us: Home Page: www.freescale.com Information in this document is provided solely to enable system and sofware implementers to use Freescale Semiconductors products. There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits or integrated circuits based on the information in this document. Freescale Semiconductor reserves the right to make changes without further notice to any products herein. Freescale Semiconductor makes no warranty, representation, or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any liability, including without limitation consequential or incidental damages. "Typical" parameters that may be provided in Freescale Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals", must be validated for each customer application by customer's technical experts. Freescale Semiconductor does not convey any license under its patent rights nor the rights of others. Freescale Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which failure of the Freescale Semiconductor product could create a situation where personal injury or death may occur. Should Buyer purchase or use Freescale Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify Freescale Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claims alleges that Freescale Semiconductor was negligent regarding the design or manufacture of the part. RoHS-compliant and/or Pb-free versions of Freescale products have the functionality and electrical characteristics as their non-RoHS-complaint and/or non-Pb-free counterparts. For further information, see http://www.freescale.com or contact your Freescale sales representative. For information on Freescale's Environmental Products program, go to http://www.freescale.com/epp. FreescaleTM and the Freescale logo are trademarks of Freescale Semiconductor, Inc. All other product or service names are the property of their respective owners. (c) 2010-2011 Freescale Semiconductor, Inc. Web Support: http://www.freescale.com/support USA/Europe or Locations Not Listed: Freescale Semiconductor Technical Information Center, EL516 2100 East Elliot Road Tempe, Arizona 85284 +1-800-521-6274 or +1-480-768-2130 www.freescale.com/support Europe, Middle East, and Africa: Freescale Halbleiter Deutschland GmbH Technical Information Center Schatzbogen 7 81829 Muenchen, Germany +44 1296 380 456 (English) +46 8 52200080 (English) +49 89 92103 559 (German) +33 1 69 35 48 48 (French) www.freescale.com/support Japan: Freescale Semiconductor Japan Ltd. Headquarters ARCO Tower 15F 1-8-1, Shimo-Meguro, Meguro-ku, Tokyo 153-0064 Japan 0120 191014 or +81 3 5437 9125 support.japan@freescale.com Asia/Pacific: Freescale Semiconductor China Ltd. Exchange Building 23F No. 118 Jianguo Road Chaoyang District Beijing 100022 China +86 10 5879 8000 support.asia@freescale.com For Literature Requests Only: Freescale Semiconductor Literature Distribution Center 1-800-441-2447 or +1-303-675-2140 Fax: +1-303-675-2150 LDCForFreescaleSemiconductor@hibbertgroup.com Document Number: K60P144M100SF2 Rev. 4, 3/2011 Preliminary |
Price & Availability of K60P144M100SF211 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |