View ENT1_134965.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

EW N
Issue 1, 16 October 2007
Radiometrix
Hartcran House, 231 Kenton Lane, Harrow, HA3 8RP, England
Tel: +44 (0) 20 8909 9595, Fax: +44 (0) 20 8909 2233
ENT1
12.5kHz Channel 12.5kHz Channel VHF High Power TX
The ENT1 transmitter modules offer a 100mW RF output VHF data link in Radiometrix SIL standard pin-out and footprint. This makes the ENT1 ideally suited to those low power applications where existing narrow band and wideband transmitters provide insufficient range. Together with the matching LMR1/RX1M receiver a oneway radio data link can be achieved over a distance up to 10km+ with suitable choice of data rate and antennas.
Figure 1: ENTI -169.40625-3
Features
* * * * * * * * Conforms to EN 300 220-3 and EN 301 489-3 Standard frequency 169.406250MHz Other frequencies from 120MHz to 180MHz 12.5 kHz channel spacing Data rates up to 3kbps Usable range over 10km Fully screened Low power requirements
www..com
Applications
* * * * * * * Remote meter reading Data loggers Industrial telemetry and telecommand In-building environmental monitoring and control High-end security and fire alarms DGPS systems Vehicle data up/download
Technical Summary
* * * * * * Size: 43 x 14.5 x 5mm Operating frequency: 169.406250MHz Supply range: 5v Current consumption: 70mA Max Data bit rate: 3kbps max. Transmit power: 20dBm (100mW) nominal
Radiometrix Ltd.,
ENT1 high power transmitter data sheet
Page 1
www..com
Radiometrix Ltd.,
ENT1 high power transmitter data sheet
Figure 2: ENT1 block diagram
Page 2
Functional description The ENT1 transmitter consists of a frequency modulated Voltage Controlled Temperature Controlled Crystal Oscillator (VCTCXO) feeding a frequency multiplier with two stage amplifier and RF filter. Final Power Amplifier stage is factory pre-set to appropriate band power level. Operation can be controlled by the EN (Enable) line, the transmitter achieving full RF output typically within 7ms of this line being pulled high. The RF output is filtered to ensure compliance with the appropriate radio regulations and fed to the 50 antenna pin.
User interface
43mm 5mm
14.5mm
ENT1
pin spacing: 2.54 mm 15.24 mm 1 = RF gnd 2 = RF out 3 = RF gnd 4 = En 5 = Vcc 6 = 0V 7 = TXD
1
2
3
4
5
6
7
7 holes of 0.7 mm dia. pin spacing 2.54 mm
Figure 3: ENT1 pin-out and dimension
ENT1 pin 1, 3 2
4
5 6 www..com 7
NOTES:
Name RFgnd RF out EN VCC 0V TXD
Function RF Ground 50 RF input from the antenna Pull high to enable Transmitter (Note 1) 5V DC power supply Ground DC coupled input for 5V CMOS logic. Rin = 100k
1. EN pin should not be left floating
Radiometrix Ltd.,
ENT1 high power transmitter data sheet
Page 3
Absolute maximum ratings
Exceeding the values given below may cause permanent damage to the module. Operating temperature Storage temperature RF in (pin 1) All other pins -10C to +60C -30C to +70C 50V @ <10MHz, +13dBm @ >10MHz -0.3V to +5.5V
Performance specifications: (Vcc = 5V / temperature = 20C unless stated)
General DC supply Supply voltage TX Supply current @ 100mW Antenna pin impedance RF centre frequency (100mW) Channel spacing Number of channels RF RF power output Spurious emissions Adjacent channel TX power Frequency accuracy FM deviation (peak) Baseband Modulation bandwidth @ -3dB TXD input level (logic low) TXD input level (logic high) Dynamic timing TX select to full RF
www..com
pin 5 5 2
min. 4.5
typ. 5 65mA 50 169.406250 12.5 1 +20 -40 0 1.5 2 0 5 7
max. 5.5
units V mA MHz kHz
notes
6
2 2
+19 -1.5 1.4 0
+21 +1.5 1.6
dBm dBm dBm kHz kHz kHz V V ms
1 5 2 3
7 7
4 4
Notes:
1. 2. 3. 4. 5. 6.
Measured into 50 resistive load. Total over full supply and temperature range. With 0V - 5.0V modulation input. To achieve specified FM deviation. Meets EN300-220 Available on other frequencies from 120MHz to 180MHz
Radiometrix Ltd.,
ENT1 high power transmitter data sheet
Page 4
Applications information
Power supply requirements
The ENT1 has a built-in regulator which delivers a constant 3.3V to the transmitter frequency control circuitry when the external supply voltage is 3.4V or greater. This ensures constant frequency stability and removes the need for external supply decoupling except in cases where the supply rail is extremely poor (ripple/noise content >0.1Vp-p).
TX modulation requirements
The module is factory-set to produce the specified FM deviation with a TXD input to pin 14 of 5V amplitude, i.e. 0V "low", 5V "high If the data input level is greater than 5V, a resistor must be added in series with the TXD input to limit the modulating input voltage to a maximum of 5V on pin 7. TXD input resistance is 100k to ground.
Expected range Predicting the range obtainable in any given situation is notoriously difficult since there are many factors involved. The main ones to consider are as follows: * * * * * Type and location of antennas in use Type of terrain and degree of obstruction of the link path Sources of interference affecting the receiver "Dead" spots caused by signal reflections from nearby conductive objects Data rate and degree of filtering employed
The following are typical examples - but range tests should always be performed before assuming that a particular range can be achieved in a given situation: Data rate 1.2kbps Note: Tx antenna half-wave Rx antenna half-wave Environment rural/open Range 10-15km
The figure for 1.2kbps assumes that the receiver bandwidth has been suitably reduced by utilising an outboard sallen-key active audio filter and data slicer or similar arrangement. www..com The ENT1's TXD input is normally driven directly by logic levels but will also accept analogue drive (e.g. 2-tone signalling). In this case it is recommended that TXD (pin 14) be DC-biased to 2.5V approx. with the modulation ac-coupled and limited to a maximum of 5Vp-p to minimise distortion over the link. Although the modulation bandwidth of the ENT1 extends down to DC it is not advisable to use data containing a DC component. This is because frequency errors and drifts between the transmitter and receiver occur in normal operation, resulting in DC offset errors on the receiver's audio output.
Radiometrix Ltd.,
ENT1 high power transmitter data sheet
Page 5
Antennas
The choice and positioning of transmitter and receiver antennas is of the utmost importance and is the single most significant factor in determining system range. The following notes are intended to assist the user in choosing the most effective antenna type for any given application. Integral antennas These are relatively inefficient compared to the larger externally-mounted types and hence tend to be effective only over limited ranges. They do however result in physically compact equipment and for this reason are often preferred for portable applications. Particular care is required with this type of antenna to achieve optimum results and the following should be taken into account: 1. Nearby conducting objects such as a PCB or battery can cause detuning or screening of the antenna which severely reduces efficiency. Ideally the antenna should stick out from the top of the product and be entirely in the clear, however this is often not desirable for practical/ergonomic reasons and a compromise may need to be reached. If an internal antenna must be used try to keep it away from other metal components and pay particular attention to the "hot" end (i.e. the far end) as this is generally the most susceptible to detuning. The space around the antenna is as important as the antenna itself. 2. Microprocessors and microcontrollers tend to radiate significant amounts of radio frequency hash which can cause desensitisation of the receiver if its antenna is in close proximity. The problem becomes worse as logic speeds increase, because fast logic edges generate harmonics across the VHF range which are then radiated effectively by the PCB tracking. In extreme cases system range may be reduced by a factor of 5 or more. To minimise any adverse effects situate antenna and module as far as possible from any such circuitry and keep PCB track lengths to the minimum possible. A ground plane can be highly effective in cutting radiated interference and its use is strongly recommended. The following types of integral antenna are in common use: Quarter-wave whip. This consists simply of a piece of wire or rod connected to the module at one end. At 169MHz the total length should be 421mm from module pin to antenna tip including any interconnecting wire or tracking. Because of the length of this antenna it is almost always external to the product casing.
www..com Helical. This
is a more compact but slightly less effective antenna formed from a coil of wire. It is very efficient for its size, but because of its high Q it suffers badly from detuning caused by proximity to nearby conductive objects and needs to be carefully trimmed for best performance in a given situation. The size shown is about the maximum commonly used at 151MHz and appropriate scaling of length, diameter and number of turns can make individual designs much smaller.
Loop. A loop of PCB track having an inside area as large as possible (minimum about 5cm2), tuned and matched with 2 capacitors. Loops are relatively inefficient but have good immunity to proximity detuning, so may be preferred in shorter range applications where high component packing density is necessary. Integral antenna summary: whip *** *** * ** helical ** ** *** * loop * * ** ***
Ultimate performance Ease of design set-up Size Immunity to proximity effects
Radiometrix Ltd.,
ENT1 high power transmitter data sheet
Page 6
421mm @ 169MHz
RF
Whip antenna
wire, rod, PCB track or a combination of these length(mm) = 71250 / freq(MHz)
RF
Helical antenna
35-40 turns wire spring length 120mm, dia 10mm trim wire length or expand coil for best results
RF Ctune C match RF GND
track width = 1mm 2 min. area 500mm capacitors may be variable or fixed (values depend on loop dimensions)
Loop antenna
Figure 4: integral antenna configurations
External antennas These have several advantages if portability is not an issue, and are essential for long range links. External antennas can be optimised for individual circumstances and may be mounted in relatively good RF locations away from sources of interference, being connected to the equipment by coax feeder. Helical. Of similar dimensions and performance to the integral type mentioned above, commerciallyavailable helical antennas normally have the coil element protected by a plastic moulding or sleeve and incorporate a coax connector at one end (usually a straight or right-angle BNC type). These are compact and simple to use as they come pre-tuned for a given application, but are relatively inefficient and are best suited to shorter ranges.
www..com Quarter-wave
whip. Again similar to the integral type, the element usually consists of a stainless steel rod or a wire contained within a semi-flexible moulded plastic jacket. Various mounting options are available, from a simple BNC connector to wall brackets, through-panel fixings and magnetic mounts for temporary attachment to steel surfaces. A significant improvement in performance is obtainable if the whip is used in conjunction with a metal ground plane. For best results this should extend all round the base of the whip out to a radius of 300mm or more (under these conditions performance approaches that of a half-wave dipole) but even relatively small metal areas will produce a worthwhile improvement over the whip alone. The ground plane should be electrically connected to the coax outer at the base of the whip. Magnetic mounts are slightly different in that they rely on capacitance between the mount and the metal surface to achieve the same result.
Radiometrix Ltd.,
ENT1 high power transmitter data sheet
Page 7
A ground plane can also be simulated by using 3 or 4 quarter-wave radials equally spaced around the base of the whip, connected at their inner ends to the outer of the coax feed. A better match to a 50 coax feed can be achieved if the elements are angled downwards at approximately 30-40 to the horizontal.
(453mm long @ 157MHz)
1/4-wave whip
1/4-wave whip
Metal ground plane
1/ (3-4 4w , eq av u e all ra y di s p al a e l ce em d) en ts
30
-40
de
g.
50 coax feed
50 coax feed
Fig.5: Quarter wave antenna / ground plane configurations Half-wave. There are two main variants of this antenna, both of which are very effective and are recommended where long range and all-round coverage are required: 1. The half-wave dipole consists of two quarter-wave whips mounted in line vertically and fed in the centre with coaxial cable. The bottom whip takes the place of the ground plane described previously. A variant is available using a helical instead of a whip for the lower element, giving similar performance with reduced overall length. This antenna is suitable for mounting on walls etc. but for best results should be kept well clear of surrounding conductive objects and structures (ideally >1m separation). 2. The end-fed half wave is the same length as the dipole but consists of a single rod or whip fed at the bottom via a matching network. Mounting options are similar to those for the quarter-wave whip. A ground plane is sometimes used but is not essential. The end-fed arrangement is often preferred www..com centre-fed dipole because it is easier to mount in the clear and above surrounding over the obstructions. Yagi. This antenna consists of two or more elements mounted parallel to each other on a central boom. It is directional and exhibits gain but tends to be large and unwieldy - for these reasons the yagi is the ideal choice for links over fixed paths where maximum range is desired.
Radiometrix Ltd.,
ENT1 high power transmitter data sheet
Page 8
Module mounting considerations The modules may be mounted vertically or bent horizontal to the motherboard. Good RF layout practice should be observed. If the connection between module and antenna is more than about 20mm long use 50 microstrip line or coax or a combination of both. It is desirable (but not essential) to fill all unused PCB area around the module with ground plane.
Variants and ordering information The ENT1 transmitter is manufactured on the 169.406250MHz European frequency allocation as standard. ENT1-169.406250-3 RF output can also be factory set from +5dBm (3mW) to +20dBm (100mW) depending on minimum order quantity.
Matching VHF Receiver:
LMR1-169-5-12k5 (12.5kHz channel version) RX1M-169-5-12k5 (12.5kHz channel version)
Note: Other variants of ENT1 (and matching receivers) can be supplied to individual customer Note requirements at frequencies from 120MHz to 180MHz and/or optimised for specific data speeds and formats. However these are subject to minimum order quantity (MOQ) and long lead time. Please consult the Sales Department for further information.
www..com
Radiometrix Ltd.,
ENT1 high power transmitter data sheet
Page 9
Notes
www..com
Radiometrix Ltd.,
ENT1 high power transmitter data sheet
Page 10
Radiometrix Ltd
Hartcran House 231 Kenton Lane Harrow, Middlesex HA3 8RP ENGLAND Tel: +44 (0) 20 8909 9595 Fax: +44 (0) 20 8909 2233 sales@radiometrix.com www.radiometrix.com Copyright notice
This product data sheet is the original work and copyrighted property of Radiometrix Ltd. Reproduction in whole or in part must give clear acknowledgement to the copyright owner.
Limitation of liability
The information furnished by Radiometrix Ltd is believed to be accurate and reliable. Radiometrix Ltd reserves the right to make changes or improvements in the design, specification or manufacture of its subassembly products without notice. Radiometrix Ltd does not assume any liability arising from the application or use of any product or circuit described herein, nor for any infringements of patents or other rights of third parties which may result from the use of its products. This data sheet neither states nor implies warranty of any kind, including fitness for any particular application. These radio devices may be subject to radio interference and may not function as intended if interference is present. We do NOT recommend their use for life critical applications. The Intrastat commodity code for all our modules is: 8542 6000
R&TTE Directive
After 7 April 2001 the manufacturer can only place finished product on the market under the provisions of the R&TTE Directive. Equipment within the scope of the R&TTE Directive may demonstrate compliance to the essential requirements specified in Article 3 of the Directive, as appropriate to the particular equipment. Further details are available on The Office of Communications (Ofcom) web site: http://www.ofcom.org.uk/radiocomms/ifi/
www..com Information
Requests Ofcom Riverside House 2a Southwark Bridge Road London SE1 9HA Tel: +44 (0)845 456 3000 or 020 7981 3040 Fax: +44 (0)20 7783 4033 information.requests@ofcom.org.uk
European Radiocommunications Office (ERO) Peblingehus Nansensgade 19 DK 1366 Copenhagen Tel. +45 33896300 Fax +45 33896330 ero@ero.dk www.ero.dk

▲Up To Search▲

Price & Availability of ENT1

	To Download ENT1 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .