View P14-3D3_216044.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

FERROXCUBE
DATA SHEET
P14/8 P cores and accessories
Supersedes data of September 2004 2008 Sep 01
Ferroxcube
P cores and accessories
CORE SETS Effective core parameters SYMBOL (I/A) Ve Ie Ae Amin m PARAMETER core factor (C1) effective volume effective length effective area minimum area mass of set VALUE 0.789 495 19.8 25.1 19.8 3.2 UNIT mm-1 mm3 mm mm2 mm2 g
2.7 11.6 0.4 0 1.2 0 6
handbook, halfpage
P14/8
9.5
0.3
0 0 14.3 0.2 0.5
0.4
0.2 0
O 3.1 0.1
0.4 0.1 5.6 0 8.4 0.2 1.2 0.15
MGC164
M1.7
Dimensions in mm.
Fig.1 P14/8 core set.
Core sets for filter applications Clamping force for AL measurements, 60 20 N. GRADE 3D3 AL (nH) 40 3% 63 3% 100 3% 1000 25% 3H3 160 3% 250 3% 315 3% 400 3% 2150 25% e 25 40 63 630 100 157 198 251 1350 TOTAL AIR GAP (m) 1170 650 360 0 220 130 100 75 0 TYPE NUMBER (WITH NUT) P14/8-3D3-E40/N P14/8-3D3-E63/N P14/8-3D3-E100/N - P14/8-3H3-A160/N P14/8-3H3-A250/N P14/8-3H3-A315/N P14/8-3H3-A400/N - TYPE NUMBER (WITHOUT NUT) P14/8-3D3-E40 P14/8-3D3-E63 P14/8-3D3-E100 P14/8-3D3 P14/8-3H3-A160 P14/8-3H3-A250 P14/8-3H3-A315 P14/8-3H3-A400 P14/8-3H3
2008 Sep 01
949
Ferroxcube
P cores and accessories
Core sets for general purpose transformers and power applications Clamping force for AL measurements, 60 20 N. GRADE 3C81 AL (nH) 63 3% 100 3% 160 3% 250 3% 315 3% 2800 25% 3C91 3F3 2800 25% 63 3% 100 3% 160 3% 250 3% 315 3% 2000 25% e 40 63 100 157 198 1 760 1 760 40 63 100 157 198 1 260 AIR GAP (m) 680 390 220 130 100 0 0 680 390 220 130 100 0
P14/8
TYPE NUMBER P14/8-3C81-E63 P14/8-3C81-A100 P14/8-3C81-A160 P14/8-3C81-A250 P14/8-3C81-A315 P14/8-3C81 P14/8-3C91 P14/8-3F3-E63 P14/8-3F3-A100 P14/8-3F3-A160 P14/8-3F3-A250 P14/8-3F3-A315 P14/8-3F3
Core sets of high permeability grades Clamping force for AL measurements, 60 20 N. GRADE 3E27 AL (nH) 5750 25% e 3610 AIR GAP (m) 0 TYPE NUMBER P14/8-3E27
Properties of core sets under power conditions B (mT) at GRADE H = 250 A/m; f = 25 kHz; T = 100 C 320 315 315 f = 25 kHz; B = 200 mT; T = 100 C 0.1 - - CORE LOSS (W) at f = 100 kHz; B = 100 mT; T = 100 C - 0.03(1) 0.06 f = 100 kHz; B = 200 mT; T = 100 C - 0.22 (1) - f = 400 kHz; B = 50 mT; T = 100 C - - 0.1
3C81 3C91 3F3 Note
1. Measured at 60 C.
2008 Sep 01
950
Ferroxcube
P cores and accessories
INDUCTANCE ADJUSTERS General data PARAMETER Material of head and thread Maximum operating temperature SPECIFICATION polypropylene (PP), glass fibre reinforced 125 C
6.7
handbook, halfpage
P14/8
O 3.13
0.07 0
2.95
M 1.7
0.7 2.4 min
MGC165
Dimensions in mm.
Fig.2 P14/8 inductance adjuster.
Inductance adjuster selection chart GRADE 3H3 AL (nH) 100 160 250 315 400 630 3D3 40 63 100 Note 1. Maximum adjustment range. TYPES FOR LOW ADJUSTMENT - - ADJ-P14-WHITE ADJ-P14-WHITE ADJ-P14-BROWN ADJ-P14-BROWN - - ADJ-P14-ORANGE
(applies to all types) L/L(1) - - 10 8 9 4 - - 11 TYPES FOR MEDIUM L/L(1) ADJUSTMENT ADJ-P14-ORANGE ADJ-P14-WHITE ADJ-P14-BROWN - - - - - - 14 17 15 - - - - - - TYPES FOR HIGH ADJUSTMENT - ADJ-P14-BROWN - - - - ADJ-P14-ORANGE ADJ-P14-ORANGE - - - 24 20 - L/L(1) - 24 - -
2008 Sep 01
951
Ferroxcube
P cores and accessories
COIL FORMERS General data for CP-P14/8 coil former PARAMETER Coil former material Maximum operating temperature SPECIFICATION
P14/8
polybutyleneterephtalate (PBT), glass reinforced, flame retardant in accordance with "UL 94V-0"; UL file number E45329 (R) 155 C, "IEC 60085", class F
handbook, full pagewidth
0 5.4 -0.2 0.4 0.3
2.2
0 0 7.1 -0.15 11.5 -0.2
6.1 +0.2 0
0.5
0.4
CBW601
Dimensions in mm.
Fig.3 Coil former CP-P14/8. Winding data and area product for CP-P14/8 coil former NUMBER OF SECTIONS 1 2 WINDING AREA (mm2) 8.8 2 x 4.0 MINIMUM WINDING WIDTH (mm) 4.1 2 x 1.85 AVERAGE LENGTH OF TURN (mm) 28.9 28.9 AREA PRODUCT Ae x Aw (mm4) 221 2 x 100
TYPE NUMBER
CP-P14/8-1S CP-P14/8-2S
2008 Sep 01
952
Ferroxcube
P cores and accessories
General data for CP-P14/8-A coil former PARAMETER Coil former material Maximum operating temperature SPECIFICATION
P14/8
acetal (POM), glass reinforced, flame retardant in accordance with "UL 94-HB"; UL file number E66288(R) 155 C, "IEC 60085", class F
6.1 min 1.9 min
5.5 max
7.1
11.55 max
MGB529
Dimensions in mm.
Fig.4 Coil former CP-P14/8-A. Winding data and area product for CP-P14/8-A coil former NUMBER OF SECTIONS 1 2 3 MINIMUM WINDING AREA (mm2) 9.4 2 x 4.32 3 x 2.19 NOMINAL WINDING WIDTH (mm) 4.5 2 x 2.0 3 x 1.2 AVERAGE LENGTH OF TURN (mm) 29.0 29.0 29.0 AREA PRODUCT Ae x Aw (mm4) 236 2 x 108 3 x 55.0
TYPE NUMBER
CP-P14/8-1S-A CP-P14/8-2S-A CP-P14/8-3S-A
2008 Sep 01
953
Ferroxcube
P cores and accessories
General data 4-pins P14/8 coil former for PCB mounting PARAMETER Coil former material Maximum operating temperature Pin material Resistance to soldering heat Solderability SPECIFICATION
P14/8
polyamide (PA6.6), glass reinforced, flame retardant in accordance with "UL 94V-0"; UL file number E41938(M) 130 C, "IEC 60085" , class B copper-zinc alloy (CuZn), tin (Sn) plated "IEC 60068-2-20", Part 2, Test Tb, method 1B, 350 C, 3.5 s "IEC 60068-2-20", Part 2, Test Ta, method 1, 235 C, 2 s
handbook, full pagewidth
3.55 0.75
5.4 max. 4.45 2
19 11.55 6 max. max. min.
16.1
7.1
2.4 6.1 max.
Dimensions in mm.
4.75 0.25
6.8 max.
CBW106
Fig.5 P14/8 coil former for PCB mounting; 4-pins. Winding data and area product for 4-pins P14/8 coil former for PCB mounting NUMBER OF SECTIONS 1 1 2 2 MINIMUM WINDING AREA (mm2) 8.65 8.65 2 x 3.87 2 x 3.87 NOMINAL WINDING WIDTH (mm) 4.4 4.4 2 x 2.0 2 x 2.0 AVERAGE LENGTH OF TURN (mm) 29.0 29.0 29.0 29.0 LENGTH OF PINS (mm) 4.75 6.8 4.75 6.8 AREA PRODUCT Ae x Aw (mm4) 217 217 2 x 97.1 2 x 97.1
TYPE NUMBER
CPV-P14/8-1S-4SPD CPV-P14/8-1S-4SPDL CPV-P14/8-2S-4SPD CPV-P14/8-2S-4SPDL
2008 Sep 01
954
Ferroxcube
P cores and accessories
General data 6-pins P14/8 coil former for PCB mounting PARAMETER Coil former material Maximum operating temperature Pin material Resistance to soldering heat Solderability SPECIFICATION
P14/8
polyamide (PA6.6), glass reinforced, flame retardant in accordance with "UL 94V-0"; UL file number E41938(M) 130 C, "IEC 60085" , class B copper-zinc alloy (CuZn), tin (Sn) plated "IEC 60068-2-20", Part 2, Test Tb, method 1B, 350 C, 3.5 s "IEC 60068-2-20", Part 2, Test Ta, method 1, 235 C, 2 s
handbook, full pagewidth
7.1 0.75
5.4 max. 4.45 2
19 11.55 6 max. max. min.
16.3
7.11 max.
2.4 10.2 max. 4.35 min. 6.85 max.
CBW107
Dimensions in mm.
Fig.6 P14/8 coil former for PCB mounting; 6-pins. Winding data and area product for 6-pins P14/8 coil former for PCB mounting NUMBER OF SECTIONS 1 1 2 2 MINIMUM WINDING AREA (mm2) 8.65 8.65 2 x 3.87 2 x 3.87 NOMINAL WINDING WIDTH (mm) 4.4 4.4 2 x 2.0 2 x 2.0 AVERAGE LENGTH OF TURN (mm) 29.0 29.0 29.0 29.0 LENGTH OF PINS (mm) 4.4 6.8 4.4 6.8 AREA PRODUCT Ae x Aw (mm 4) 217 217 2 x 97.1 2 x 97.1
TYPE NUMBER
CPV-P14/8-1S-6PD CPV-P14/8-1S-6PDL CPV-P14/8-2S-6PD CPV-P14/8-2S-6PDL
2008 Sep 01
955
Ferroxcube
P cores and accessories
MOUNTING PARTS General data for mounting parts ITEM Tag plate REMARKS material: phenolformaldehyde (PF), glass reinforced flame retardant: in accordance with "UL 94V-0" ; UL file number E41429 maximum operating temperature: 180 C, "IEC 60085", class H pins: copper-tin alloy (CuSn), tin (Sn) plated resistance to soldering heat in accordance with "IEC 60 068-2-20", Part 2, Test Tb, method 1B: 350 C, 3.5 s solderability in accordance with "IEC 60068-2-20", Part 2, Test Ta, method 1: 235 C, 2 s Container Spring Clamp Washer copper-zinc alloy (CuZn), tin (Sn) plated earth pins: presoldered CrNi-steel spring force: 60 N when mounted spring steel, tin-plated phenolformaldehyde (PF) 10 11 9 SPR-P14/8 8 CON-P14/8 FIGURE 7
P14/8
TYPE NUMBER TGP-P14/8-C
CLM/TP-P14/8 WAS-CLM/TP-P14/8
2.54 2.1 5.08 1.5
mark 10.16 5.08 3.5
0.8
15.7 max.
6
1.3 +0.15 0
CBW602
Dimensions in mm.
Fig.7 Tag plate: TGP-P14/8-C.
2008 Sep 01
956
Ferroxcube
P cores and accessories
P14/8
handbook, full pagewidth
4.5
mark
0.6 5 8 9.45 max. 1 15.6 max.
CBW422
Dimensions in mm.
Fig.8 Container: CON-P14/8.
handbook, halfpage
1.3
+0.3 0
13.4 max
MGC169
Dimensions in mm.
Fig.9 Spring: SPR-P14/8.
2008 Sep 01
957
Ferroxcube
P cores and accessories
P14/8
handbook, halfpage
handbook, halfpage
9.4 13.2 9.27 0.05 13 4 0.38 0.08 9.65 0 13.7 - 0.13
MGB604
MBG174
Dimensions in mm.
Dimensions in mm.
Fig.10 Clamp: CLM/TP-P14/8.
Fig.11 Washer: WAS-CLM/TP-P14/8.
2008 Sep 01
958
Ferroxcube
P cores and accessories
DATA SHEET STATUS DEFINITIONS DATA SHEET STATUS Preliminary specification Product specification PRODUCT STATUS Development DEFINITIONS
P14/8
This data sheet contains preliminary data. Ferroxcube reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. This data sheet contains final specifications. Ferroxcube reserves the right to make changes at any time without notice in order to improve design and supply the best possible product.
Production
DISCLAIMER Life support applications These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Ferroxcube customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Ferroxcube for any damages resulting from such application. PRODUCT STATUS DEFINITIONS STATUS Prototype Design-in Preferred Support INDICATION DEFINITION These are products that have been made as development samples for the purposes of technical evaluation only. The data for these types is provisional and is subject to change. These products are recommended for new designs. These products are recommended for use in current designs and are available via our sales channels. These products are not recommended for new designs and may not be available through all of our sales channels. Customers are advised to check for availability.
2008 Sep 01
959

▲Up To Search▲

Price & Availability of P14-3D3

	To Download P14-3D3 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .