|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
www..com LIS2L01 INERTIAL SENSOR: 2Axis/1g LINEAR ACCELEROMETER PRODUCT PREVIEW s s s s s s THE SENSITIVITY IS ADJUSTED WITH A TOTAL ACCURACY OF 2.5% INTERNAL TWO POLES LOW PASS SC FILTER WITH LINEAR OUTPUT, 30Hz BANDWIDTH THE OUTPUT VOLTAGE, OFFSET, SENSITIVITY AND TEST VOLTAGE ARE RATIOMETRIC TO THE SUPPLY VOLTAGE DEVICE SENSITIVITY IS ON-CHIP FACTORY TRIMMED EMBEDDED SELF TEST HIGH SHOCK SURVIVABILITY SO-24 ORDERING NUMBER: LIS2L01 DESCRIPTION The LIS2L01 is a dual channel accelerometer that includes a sensor elements and an IC interface able to take the information from the sensor and to provide an analog signal to the external world. The sensor element, capable to detect the acceleration, is manufactured using a dedicated process called ThELMA (Thick Epi-Poly layer for Microactuators and Accelerometers) developed by ST to produce inertial sensor and actuator in silicon. The IC interface instead is manufactured using a CMOS process that allow high level of integration to design a dedicated circuit which is trimmed to better match the sensor element characteristics. BLOCK DIAGRAM The LIS2L01 is capable of measuring acceleration in the range of 1g with a bandwidth of 30Hz, set by a 2nd order low pass filter. A self-test capability verifies the system providing to the user a signal on a dedicated pin. The LIS2L01 is available in plastic SMD package and it is specified over a temperature range from 0C to +80C. The LIS2L01 is a part of family products suitable for a variety of applications: - Virtual reality input devices - Computer hard disk drive protection - Computer mouse and joysticks - Vibration Monitoring, recording and compensation - Appliance control - Robotics Sy Sx MUX CHARGE PREAMPLIFIER MUX SC FILTER & CDS VARIABLE GAIN AMPLIFIER VOUTx VARIABLE GAIN AMPLIFIER VOUTy Sy Sx SC FILTER & CDS TRIMMING CIRCUIT & POLY FUSES D01IN1315 VOLTAGE & CURRENT REFERENCE CLOCK & PHASE GENERATOR April 2002 This is preliminary information on a new product now in development. Details are subject to change without notice. 1/6 DataSheet 4 U .com www..com LIS2L01 PIN DESCRIPTION N 1 to 5 6, 9, 10 7, 8 11, 12 13 14 15 16 17 18 19 20 to 24 Pin NC Reserved Reserved NC Vdd GND VoutX ST VoutY Reserved Reserved NC Internally not connected Leave unconnected or connect to GND Leave unconnected or connect to Vdd Internally not connected 5V Supply 0V Supply Voltage Output Self Test Voltage Output Leave unconnected or connect to GND Leave unconnected or connect to Vdd Internally not connected Function PIN CONNECTION (Top view) N.C. N.C. N.C. Y X N.C. N.C. DIRECTION OF THE RESERVED DETECTABLE RESERVED ACCELERATION RESERVED RESERVED RESERVED N.C. N.C. 1 2 3 4 5 6 7 8 9 10 11 12 D01IN1314 24 23 22 21 20 19 18 17 16 15 14 13 N.C. N.C. N.C. N.C. N.C. RESERVED RESERVED VoutY ST VoutX GND Vdd 2/6 DataSheet 4 U .com www..com LIS2L01 ELECTRICAL CHARACTERISTCS (Temperature range 0C to 80C, supply voltage Vdd = 5V 5%.) Symbol Vdd Idd Voff Ar So fuc an Vt Vst Parameter Supply voltage Supply current Zero-g level Acceleration range Sensitivity ratiometric to Vdd Upper cutoff frequency low pass filter Equivalent noise acceleration Self test output voltage Ratiometric to Vdd Self test input Logic 1 voltage Logic 0 voltage Capacitive load drive Resistive load output 50 Vdd = 5V T = 25C -3dB/2nd order filter Bandwidth = 0.1...30Hz T = 25C @ 5V 3.75 Vss T = 25C ratiometric to Vdd Vdd/2 - 0.1 TBD 1.8 27 Test Condition Min. 4.75 Typ. 5 10 Vdd/2 1 2 30 1 TBD Vdd/2 + 0.1 TBD 2.2 33 Max. 5.25 Unit V mA V g V/g Hz mg V Vdd 1.25 100 V V pF Cload Rload k 1 FUNCTIONALITY 1.1 Sensor element The ThELMA process is utilized to create a surface micro-machined accelerometer. The technology allows carry out silicon structure on suspension, the structure are attached to the substrate in few points called anchor and free to move on a plane parallel to the substrate itself. To be compatible with the traditional packaging techniques a cap is placed on top the sensor element to avoid the molding goes between the elements making the sensor useless. The equivalent circuit for the sensor is shown in the below figure; when a linear acceleration is applied, the proof mass displaces from its nominal position, causing an imbalance in the capacitive half-bridge. This imbalance is measured using charge integration in response to a voltage pulse applied to the sense capacitor. The nominal value of the capacitors, at steady state, is few pF and when an acceleration is applied the maximum variation of the capacitive load is few tenth of pF. 3/6 DataSheet 4 U .com www..com LIS2L01 Figure 1. Equivalent electrical circuit Cps1 Rs1 S1x Cs1x Cpr Rr Cs2x S2x Cps2 Cps1 Rs2 Rs1 S1y Cs1y Cpr Rr rot Cs2y S2y Cps2 Rs2 1.2 IC Interface The complete signal processing uses a fully differential structure, while the final stage converts the differential signal into a single-ended to be compatible with the external world. The first stage is a low-noise capacitive amplifier that implements a Correlated Double Sampling (CDS) at the output to cancel the offset and the 1/f noise. The signal is processed through a 2nd order low pass filter in order to reject out of band noise, the filter cut off frequency is set to be 30Hz. This filter is implemented using SC technique, which allows to realize a fully integrated system that avoid the use of any external component. The low noise input amplifier operates at 100 kHz while the two SC filters operate at 50 kHz sampling frequency. This allows a large oversampling ratio, able to reduce in-band noise and to obtain an accurate output waveform. The signal at the output of the SC filter is sampled and held using a different clock to avoid that the filter output value during the CDS phase reaches the output pin. All the analog parameter (output offset voltage and sensitivity) are ratiometric to the supply voltage. Increasing or decreasing the supply voltage, the sensitivity and the offset will increase or decrease linearly. The feature provides the cancellation of the error related to the supply voltage in the analog to digital conversion chain. 1.3 Factory calibration In the IC interface different calibrations take place at factory level to provide to final user a device ready to be used, the trimmed parameters are: gain, offset and cut off frequency of the SC filter. The trimmed value are stored in the device with a poly-fuse technique. Any time the device is turned on the memorized bits are loaded into the registers to be utilized during the normal operation. The poly-fuse approach allow the final user to use the device without any need for further calibration. 4/6 DataSheet 4 U .com www..com LIS2L01 DIM. MIN. A A1 A2 B C D E e H h k L 0.40 10.0 0.25 0.33 0.23 15.20 7.40 2.35 0.10 mm TYP. MAX. 2.65 0.30 2.55 0.51 0.32 15.60 7.60 1.27 10.65 0.75 0.394 0.010 0.013 0.009 0.598 0.291 MIN. 0.093 0.004 inch TYP. MAX. 0.104 0.012 0.100 0.0200 0.013 0.614 0.299 0,050 0.419 0.030 OUTLINE AND MECHANICAL DATA 0 (min.), 8 (max.) SO24 1.27 0.016 0.050 h x 45 A2 A1 A 0.10mm .004 Seating Plane B e K L H A1 C D 24 13 1 12 SO24 E 5/6 DataSheet 4 U .com www..com LIS2L01 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics (R) 2002 STMicroelectronics - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom - United States. http://www.st.com 6/6 DataSheet 4 U .com |
Price & Availability of LIS2L01 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |