|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
(R) HA-2842 Data Sheet June 2003 FN2766.6 80MHz, High Slew Rate, High Output Current, Video Operational Amplifier The HA-2842 is a wideband, high slew rate, operational amplifier featuring an outstanding combination of speed, bandwidth, and output drive capability. This amplifier's performance is further enhanced through stable operation down to closed loop gains of +2, the inclusion of offset null controls, and by its excellent video performance. The capabilities of the HA-2842 are ideally suited for high speed cable driver circuits, where low closed loop gains and high output drive are required. With a 6MHz full power bandwidth, this amplifier is well suited for high frequency signal conditioning circuits and video amplifiers. Gain flatness of 0.035dB, combined with differential gain and phase specifications of 0.02%, and 0.03 degrees, respectively, make the HA-2842 ideal for component and composite video applications. A zener/nichrome based reference circuit, coupled with advanced laser trimming techniques, yields a supply current with a low temperature coefficient and low lot-to-lot variability. For example, the average ICC variation from 85oC to -40oC is <600A (2%), while the standard deviation of the ICC distribution is <0.1mA (0.8%) at 25oC. Tighter ICC control translates to more consistent AC parameters ensuring that units from each lot perform the same way, and easing the task of designing systems for wide temperature ranges. Critical AC parameters, Slew Rate and Bandwidth, each vary by less than 5% over the industrial temperature range (see Typical Performance Curves) Features * Stable at Gains of 2 or Greater * Low AC Variability Over Process and Temperature * Gain Bandwidth . . . . . . . . . . . . . . . . . . . . . . . . . . . 80MHz * Gain Flatness to 10MHz. . . . . . . . . . . . . . . . . . . . 0.035dB * High Slew Rate . . . . . . . . . . . . . . . . . . . . . . . . . . 400V/s * High Output Current (Min) . . . . . . . . . . . . . . . . . . . 100mA * Differential Gain/Phase . . . . . . . . . . 0.02%/0.03 Degrees * Low Supply Current (Max) . . . . . . . . . . . . . . . . . . . . 15mA * Enhanced Replacement for AD842 Applications * Pulse and Video Amplifiers * Wideband Amplifiers * Coaxial Cable Drivers * Fast Sample-Hold Circuits * High Frequency Signal Conditioning Circuits Pinout HA-2842 (SOIC) TOP VIEW BAL -IN +IN 1 2 3 4 + 8 7 6 5 BAL V+ OUT NC Ordering Information. PART NUMBER (BRAND) HA9P2842-5 (H2842F5) TEMP. RANGE (oC) 0 to 75 PACKAGE 8 Ld SOIC PKG. DWG. # M8.15 V- 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright (c) Intersil Americas Inc. 2003. All Rights Reserved. All other trademarks mentioned are the property of their respective owners. HA-2842 Absolute Maximum Ratings Voltage Between V+ and V- Terminals . . . . . . . . . . . . . . . . . . . 35V Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6V Output Current (Notes 3, 4) . . . . . . . . . . . . . . . . . . . . . . . . . . 125mA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100mA (50% Duty Cycle) Thermal Information Thermal Resistance (Typical, Note 2) JA (oC/W) Operating Conditions Temperature Range HA-2842-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0oC to 75oC Recommended Supply Voltage Range . . . . . . . . . . . 6.5V to 15V 8 Lead SOIC Package . . . . . . . . . . . . . . . . . . . . . . . 160 Maximum Junction Temperature (Die). . . . . . . . . . . . . . . . . . . .175oC Maximum Junction Temperature (Plastic Package, Note 1) . . . 150oC Maximum Storage Temperature Range . . . . . . . . . -65oC to 150oC Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300oC (Lead Tips Only) CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTES: 1. Maximum power dissipation, including output load, must be designed to maintain the maximum junction temperature below 150oC for plastic packages. By using Application Note AN556 on Safe Operating Area equations, along with the packaging thermal resistances listed in the Thermal Information section, proper load conditions can be determined. 2. JA is measured with the component mounted on an evaluation PC board in free air. 3. VO = 5V, RL Unconnected, Duty cycle 50%. For information about using high output current amplifiers, please refer to Application Note AN556 (Thermal Safe-Operating-Areas For High Current Op Amps), and the "Power Dissipation Considerations" section in the "Application Information" section of this datasheet. 4. Maximum continuous (100% Duty Cycle) output current is 50mA. For currents >50mA, Duty Cycle must be derated accordingly. Electrical Specifications PARAMETER INPUT CHARACTERISTICS Offset Voltage (Note 10) VSUPPLY = 15V, RL = 1k , CL 10pF, Unless Otherwise Specified HA-2842-5 TEST CONDITIONS TEMP (oC) MIN TYP MAX UNITS 25 Full 10 - 1 13 5 20 0.5 1.3 170 1 16 16 2 3 6 10 15 1.0 1.5 - mV mV V/oC A A nA/oC A A nA/oC k pF V VRMS nV Hz pA Hz Average Offset Voltage Drift Bias Current (Note 10) Full 25 Full Average Bias Current Drift Offset Current Full 25 Full Average Offset Current Drift Input Resistance Input Capacitance Common Mode Range Input Noise Voltage Input Noise Voltage Density Input Noise Current (Note 10) TRANSFER CHARACTERISTICS Large Signal Voltage Gain VO = 10V VCM = 10V 10Hz to 1MHz f = 1kHz, RSOURCE = 0 f = 1kHz, RSOURCE = 100k Full 25 25 Full 25 25 25 25 Full 50 30 80 2 - 100 60 110 80 0.035 - kV/V kV/V dB V/V MHz dB Common-Mode Rejection Ratio (Note 10) Minimum Stable Gain Gain Bandwidth Product (Note 10) Gain Flatness to 10MHz (Note 10) Full 25 AVCL = 100 RL 75 25 25 2 HA-2842 Electrical Specifications PARAMETER OUTPUT CHARACTERISTICS Output Voltage Swing (Note, 10) Output Current (Note 10) Output Resistance Full Power Bandwidth (Note 6) Differential Gain (Note 10) Differential Phase (Note 10) Harmonic Distortion (Note 10) TRANSIENT RESPONSE (Note 7) Rise Time Overshoot Slew Rate (Notes 9, 10) Settling Time POWER REQUIREMENTS Supply Current (Note 10) 25 Full Power Supply Rejection Ratio (Note 10) NOTES: 5. Differential gain and phase are measured with a VM700A video tester, using a NTC-7 composite VITS. RF = R1 = 1k, RL = 700. Slew Rate 6. Full Power Bandwidth guaranteed based on slew rate measurement using FPBW = --------------------------- ; V PEAK = 10V . 2V PEAK 7. Refer to Test Circuits section of this data sheet. 8. VSUPPLY = 10V to 20V. 9. This parameter is not tested. The limits are guaranteed based on lab characterization and reflect lot-to-lot variation. 10. See "Typical Performance Curves" for more information. (Note 8) Full 70 14.2 14.3 80 15 mA mA dB AV = +2 10V Step to 0.1% 25 25 25 25 325 4 25 400 100 ns % V/s ns VO = 10V (Note 5) (Note 5) VO = 2VP-P, f = 1MHz, AV = 2 VO = 10V (Note 3) Full Full 25 25 25 25 25 10 100 5.2 11 8.5 6 0.02 0.03 >81 V mA MHz % Degrees dBc VSUPPLY = 15V, RL = 1k , CL 10pF, Unless Otherwise Specified (Continued) HA-2842-5 TEST CONDITIONS TEMP (oC) MIN TYP MAX UNITS 3 HA-2842 Test Circuits and Waveforms IN + - OUT 500 NOTES: 11. VS = 15V. 12. AV = +2. 13. CL 10pF 500 TEST CIRCUIT INPUT INPUT OUTPUT OUTPUT Input = 5V/Div., Output = 5V/Div., 50ns/Div. LARGE SIGNAL RESPONSE SETTLING POINT Input = 100mV/Div., Output = 100mV/Div., 50ns/Div. SMALL SIGNAL RESPONSE NOTES: 14. AV = -2. 15. Feedback and summing resistors must be matched (0.1%). 16. HP5082-2810 clipping diodes recommended. 17. Tektronix P6201 FET probe used at settling point. 18. For 0.01% settling time, heat sinking is suggested to reduce thermal effects and an analog ground plane with supply decoupling is suggested to minimize ground loop errors. 2.5k 5k 1k V+ 500 VIN + VOUT V- SETTLING TIME TEST CIRCUIT V+ 5k + BAL OUT V- SUGESTED OFFSET VOLTAGE ADJUSTMENT 4 HA-2842 Application Information The Intersil HA-2842 is a state of the art monolithic device which also approaches the "ALL-IN-ONE" amplifier concept. This device features an outstanding set of AC parameters augmented by excellent output drive capability providing for suitable application in both high speed and high output drive circuits. Primarily intended to be used in balanced 50 and 75 coaxial cable systems as a driver, the HA-2842 could also be used as a power booster in audio systems as well as a power amp in power supply circuits. This device would also be suitable as a small DC motor driver. Power Dissipation Considerations At high output currents, especially with the 8 lead SOIC package, care must be taken to ensure that the Maximum Junction Temperature (TJ, see "Absolute Maximum Ratings" table) isn't exceeded. As an example consider the HA-2842 in the SOIC package, with a required output current of 50mA at VOUT = 10V with 15V supplies. The power dissipation is the quiescent power (450mW = 30V x 15mA) plus the power dissipated in the output stage (POUT = 250mW = 50mA x (15V - 10V)), or a total of 700mW. The thermal resistance (JA) of the SOIC package is 157oC/W, which increases the junction temperature by 110oC over the ambient temperature (TA). Remaining below TJMAX requires that TA be restricted to 40oC (150oC - 110oC). Heatsinking would be required for operation at ambient temperatures greater than 40oC. MAX POUT WITHOUT HEATSINK (VS = 15V) TA 85oC 70oC 25oC 8 LEAD SOIC (JA = 157oC/W) Heatsink Required 60mW 350mW Prototyping Guidelines For best overall performance in any application, it is recommended that high frequency layout techniques be used. This should include: 1. Mounting the device through a ground plane. 2. Connecting unused pins (NC) to the ground plane. 3. Mounting feedback components on Teflon standoffs and/or locating these components as close to the device as possible. 4. Placing power supply decoupling capacitors from device supply pins to ground. Allowable output power can be increased by decreasing the quiescent dissipation via lower supply voltages. For more information please refer to Application Note AN556, Thermal Safe Operating Areas for High Current Op Amps. Typical Performance Curves 120 100 80 60 GAIN (dB) 40 20 0 TA = 25oC, VSUPPLY = 15V, RL = 1k , CL < 10pF, Unless Otherwise Specified 100 AVCL = 1000 AVCL = 100 AVCL = 2 PHASE (DEGREE) AVCL = 10 GAIN BANDWIDTH PRODUCT (MHz) OPEN LOOP 90 80 70 60 50 40 30 0 90 OPEN LOOP AVCL AVCL = 1000 = 100 10K 100K 1M AVCL AVCL = 10 = 2 10M 180 10 100 1K 100M 5 6 7 FREQUENCY (Hz) 8 9 10 11 12 SUPPLY VOLTAGE (V) 13 14 15 FIGURE 1. FREQUENCY RESPONSE FOR VARIOUS GAINS FIGURE 2. GAIN BANDWIDTH PRODUCT vs SUPPLY VOLTAGE 5 HA-2842 Typical Performance Curves 100 GAIN BANDWIDTH PRODUCT (MHz) 90 100 80 90 70 60 50 60 40 50 30 -60 -40 -20 0 20 40 60 80 100 120 140 100 1K 10K 100K 1M 10M TEMPERATURE (oC) CMRR (dB) 80 70 TA = 25oC, VSUPPLY = 15V, RL = 1k , CL < 10pF, Unless Otherwise Specified (Continued) 110 FREQUENCY (Hz) FIGURE 3. GAIN BANDWIDTH PRODUCT vs TEMPERATURE FIGURE 4. CMRR vs FREQUENCY 50 NOISE VOLTAGE (nV/Hz) 90 80 PSRR (dB) 70 60 50 40 30 20 10 1K 10K 100K FREQUENCY (Hz) 1M 10M 10 100 1K FREQUENCY (Hz) 10K 40 30 20 10 0 20 16 12 8 4 0 NOISE VOLTAGE NOISE CURRENT 100K FIGURE 5. PSRR vs FREQUENCY FIGURE 6. INPUT NOISE vs FREQUENCY 425 450 SLEW RATE (V/s) 400 SLEW RATE (V/s) 400 350 375 300 350 250 200 -60 -40 -20 0 20 40 60 80 100 120 140 5 6 7 8 9 10 11 12 13 14 15 TEMPERATURE (oC) SUPPLY VOLTAGE (V) FIGURE 7. SLEW RATE vs TEMPERATURE FIGURE 8. SLEW RATE vs SUPPLY VOLTAGE 6 NOISE CURRENT (pA/Hz) HA-2842 Typical Performance Curves 8 TA = 25oC, VSUPPLY = 15V, RL = 1k , CL < 10pF, Unless Otherwise Specified (Continued) 3 INPUT OFFSET VOLTAGE (mV) 16 14 SUPPLY CURRENT (mA) 12 10 8 6 4 5 6 7 8 9 10 11 12 13 14 15 SUPPLY VOLTAGE (V) INPUT BIAS CURRENT (A) 7 OFFSET VOLTAGE 2 6 1 125oC 5 BIAS CURRENT 4 0 25oC -55oC -1 3 -60 -40 -20 0 20 40 60 80 100 120 -2 140 TEMPERATURE (oC) FIGURE 9. INPUT OFFSET VOLTAGE AND INPUT BIAS CURRENT vs TEMPERATURE FIGURE 10. SUPPLY CURRENT vs SUPPLY VOLTAGE 15 NEGATIVE OUTPUT SWING (V) 15V, 1k 12.5 15V, 150 -2.5 8V, 150 8V, 75 POSITIVE OUTPUT SWING (V) -5 8V, 1k 15V, 75 15V, 150 10 15V, 75 7.5 8V, 1k 5 8V, 150 -40 -20 0 20 40 8V, 75 60 80 100 120 140 TEMPERATURE (oC) -7.5 -10 -12.5 15V, 1k -40 -20 0 20 40 60 80 100 120 140 2.5 -60 -15 -60 TEMPERATURE (oC) FIGURE 11. POSITIVE OUTPUT SWING vs TEMPERATURE 30 OUTPUT VOLTAGE SWING (VP-P) 25 20 VSUPPLY = 15V FIGURE 12. NEGATIVE OUTPUT SWING vs TEMPERATURE -40 -50 THD (dBc) VO = 10VP-P -60 15 VSUPPLY = 8V 10 5 0 -70 -80 VO = 1VP-P VO = 0.5VP-P VO = 2VP-P -90 1K 10K 100K 1M 10M 100M 100K 1M FREQUENCY (Hz) 10M FREQUENCY (Hz) FIGURE 13. MAXIMUM UNDISTORTED OUTPUT SWING vs FREQUENCY FIGURE 14. TOTAL HARMONIC DISTORTION vs FREQUENCY 7 HA-2842 Typical Performance Curves -40 THIRD INTERMOD PRODUCT (dBc) TA = 25oC, VSUPPLY = 15V, RL = 1k , CL < 10pF, Unless Otherwise Specified (Continued) 0.025 VO = 5VP-P VO = 2VP-P VSUPPLY = 8V -50 -60 DIFFERENTIAL GAIN (%) 0.020 0.015 -70 0.010 VSUPPLY = 15V 0.005 VSUPPLY = 10V -80 VO = 1VP-P VO = 0.50VP-P VO = 0.25VP-P 500K 1M FREQUENCY (Hz) 10M -90 0 100 200 300 400 500 600 700 800 900 1000 LOAD RESISTANCE () FIGURE 15. INTERMODULATION DISTORTION vs FREQUENCY (TWO TONE) FIGURE 16. DIFFERENTIAL GAIN vs LOAD RESISTANCE 0.14 DIFFERENTIAL PHASE (DEGREES) 0.12 0.10 0.08 VSUPPLY = 10V 0.06 0.04 0.02 0 100 200 300 400 500 600 700 800 900 1000 LOAD RESISTANCE () VSUPPLY = 15V VSUPPLY = 8V GAIN FLATNESS (dB) 0.04 RL = 75 0.03 0.02 RL = 150 0.01 RL = 500 RL = 1000 0 0 1M 2M 3M 4M 5M 6M 7M 8M 9M 10M FREQUENCY (Hz) FIGURE 17. DIFFERENTIAL PHASE vs LOAD RESISTANCE FIGURE 18. GAIN FLATNESS vs FREQUENCY (AVCL = 2) 85 GAIN BANDWIDTH PRODUCT (MHz) 80 75 70 65 0 100 200 300 400 500 600 700 800 900 1000 LOAD RESISTANCE () FIGURE 19. GAIN BANDWIDTH PRODUCT vs LOAD RESISTANCE 8 HA-2842 Die Characteristics DIE DIMENSIONS: 77 mils x 81 mils x 19 mils 1960m x 2060m x 483m METALLIZATION: Type: Aluminum, 1% Copper Thickness: 16kA 2kA PASSIVATION: Type: Nitride over Silox Silox Thickness: 12kA 2kA Nitride thickness: 3.5kA 1kA SUBSTRATE POTENTIAL (POWERED UP): VTRANSISTOR COUNT: 58 PROCESS: High Frequency Bipolar Dielectric Isolation Metallization Mask Layout HA-2842 BAL BAL COMP -IN V+ OUT +IN V- 9 HA-2842 Small Outline Plastic Packages (SOIC) N INDEX AREA E -B1 2 3 SEATING PLANE -AD -CA h x 45o H 0.25(0.010) M BM M8.15 (JEDEC MS-012-AA ISSUE C) 8 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE INCHES SYMBOL A L MILLIMETERS MIN 1.35 0.10 0.33 0.19 4.80 3.80 MAX 1.75 0.25 0.51 0.25 5.00 4.00 NOTES 9 3 4 5 6 7 8o Rev. 0 12/93 MIN 0.0532 0.0040 0.013 0.0075 0.1890 0.1497 MAX 0.0688 0.0098 0.020 0.0098 0.1968 0.1574 A1 B C D E A1 0.10(0.004) C e H h L N 0.050 BSC 0.2284 0.0099 0.016 8 0o 8o 0.2440 0.0196 0.050 1.27 BSC 5.80 0.25 0.40 8 0o 6.20 0.50 1.27 e B 0.25(0.010) M C AM BS NOTES: 1. Symbols are defined in the "MO Series Symbol List" in Section 2.2 of Publication Number 95. 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 3. Dimension "D" does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006 inch) per side. 4. Dimension "E" does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.25mm (0.010 inch) per side. 5. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 6. "L" is the length of terminal for soldering to a substrate. 7. "N" is the number of terminal positions. 8. Terminal numbers are shown for reference only. 9. The lead width "B", as measured 0.36mm (0.014 inch) or greater above the seating plane, shall not exceed a maximum value of 0.61mm (0.024 inch). 10. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact. All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation's quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 10 |
Price & Availability of HA-2842 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |