 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| 5 Tap High Speed CMOS (HCT) Compatible Active Delay Lines Delays are 5% or 2 nS Tap Total 12* 17 12* 18 12* 19 12* 20 12* 21 12* 22 12* 24 15 30 20 40 25 50 30 60 35 70 40 80 50 100 60 120 70 140 22 24 26 28 30 32 36 45 60 75 90 105 120 150 180 210 27 30 33 36 39 42 48 60 80 100 120 140 160 200 240 280 32 36 40 44 48 52 60 75 100 125 150 175 200 250 300 350 DIP Part Number EP9604-32 EP9604-36 EP9604-40 EP9604-44 EP9604-48 EP9604-52 EP9604-60 EP9604-75 EP9604-100 EP9604-125 EP9604-150 EP9604-175 EP9604-200 EP9604-250 EP9604-300 EP9604-350 SMD Part Number EP9604G-32 EP9604G-36 EP9604G-40 EP9604G-44 EP9604G-48 EP9604G-52 EP9604G-60 EP9604G-75 EP9604G-100 EP9604G-125 EP9604G-150 EP9604G-175 EP9604G-200 EP9604G-250 EP9604G-300 EP9604G-350 Delays are 5% or 2 nS Tap Total 80 84 88 90 100 110 120 130 140 150 160 170 180 190 200 160 168 176 180 200 220 240 260 280 300 320 340 360 380 400 240 252 264 270 300 330 360 390 420 450 480 510 540 570 600 320 400 336 420 352 440 360 450 400 500 440 550 480 600 520 650 560 700 600 750 640 800 680 850 720 900 760 950 800 1000 DIP Part Number EP9604-400 EP9604-420 EP9604-440 EP9604-450 EP9604-500 EP9604-550 EP9604-600 EP9604-650 EP9604-700 EP9604-750 EP9604-800 EP9604-850 EP9604-900 EP9604-950 EP9604-1000 SMD Part Number EP9604G-400 EP9604G-420 EP9604G-440 EP9604G-450 EP9604G-500 EP9604G-550 EP9604G-600 EP9604G-650 EP9604G-700 EP9604G-750 EP9604G-800 EP9604G-850 EP9604G-900 EP9604G-950 EP9604G-1000 Whichever is greater. * Inherent Delay * Delay times referenced from input to leading edges at 25C, 5.0V. DC Electrical Characteristics Parameter Test Conditions VIH VIL VOH VOL IL I CCL TRO NH High Level Input Voltage Low Level Input Voltage High Level Output Voltage Low Level Output Voltage Input Leakage Current Supply Current Output Rise Time High Fanout VCC = 4.5 to 5.5 VCC = 4.5 to 5.5 VCC = 4.5V,IO= -4.0mA @ VIH or VIL VCC = 4.5V,IO = 4.0mA @ VIH or VIL VCC = 5.5V @ VIH or VIL VCC = 5.5V, VIN = 0 550 nS (.75 - 2.4 Volts) >550 nS VCC = 5.5V, VOH = 4.0V Schematic Min Max Unit 2.0 0.8 4.0 0.3 Volt Volt Volt Volt 14 VCC 12 4 10 6 8 OUTPUT INPUT 1 10 1.0 uA 15 mA 4 nS 5 nS LSTTL Load 7 GROUND Input Pulse Test Conditions @ 25C EIN PW TRI PRR VCC Pulse Input Voltage Pulse Width % of Total Delay Input Rise Time (0.75 - 2.4 Volts) Pulse Repetition Rate @ PW 500nS Pulse Repetition Rate @ PW > 500nS Supply Voltage 3.2 150 2.0 1.0 100 5.0 Unit Volts % nS MHz KHz Volts Recommended Operating Conditions VCC VI VO IO PW* D* TA DC Supply Voltage DC Input Voltage Range DC Output Voltage Range DC Output Source/Sink Current Pulse Width % of Total Delay Duty Cycle Operating Free Air Temperature Min 4.5 0 0 40 0 Max 5.5 VCC VCC 25 40 70 Unit Volt Volt Volt mA % % C *These two values are inter-dependent. SMD Package .200 DIP Package .200 White Dot Pin#1 PCA EP9604G-32 Date Code .300 .280 Max. .400 Max. PCA EP9604G-32 Date Code .300 .200 .280 Max. Suggested Solder Pad Layout .055 .410 .100 .300 .03 .780 Max. .020 Min. .010 Typ. .780 Max. .250 Max. .02 .100 .01 Typ. .250 Max. .050 .300 .020 Typ. .150 Typ. .365 Max. DSD9604/G Rev. A 2/5/96 QAF-CSO1a Rev. B 8/25/94 Unless Otherwise Noted Dimensions in Inches Tolerances: Fractional = 1/32 .XX = .030 .XXX = .010 ELECTRONICS INC. 16799 SCHOENBORN ST. NORTH HILLS, CA 91343 TEL: (818) 892-0761 FAX: (818) 894-5791 |
Price & Availability of EP9604G-32
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |