View SO-502-BHC-LNN1350_545751.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

SO-502 SAW Based Oscillator Product Data Sheet
PRELIMINARY
SO-502
SAW Based Clock Oscillator
Features
* Output frequencies from 300 MHz to 1350 MHz * Ultra low jitter < 1.0 ps-rms (12 kHz to 20 MHz) < 1.0 ps-rms (50 kHz to 80 MHz) * Small low profile 9.0 * 14 * 4.5 mm SMT package * 3.3 V, 5.0 V and 12V Supply Options * Low phase noise, -160 dBc/Hz @ 1 MHz offset (1 GHz) * LV-PECL, PECL, or Sinewave (0 to +10 dBm into 50) * Output disable feature (For LVPECL - PECL option)
Applications
* Point to Point / Point to Multi Point Radios * Instrumentation * Test & Measurement * Military & Avionics
Description
The SO-502 is a SAW based clock oscillator that operates at the fundamental frequency of the internal SAW resonator. This direct approach enables this series to achieve low phase noise and jitter performance at high output frequencies and over wide operating temperature range. The oscillator is housed in a hermetically sealed J-lead surface mount package offered on tape and reel. As an option, it has an output disable to facilitate on-board testing.
Vectron International, 267 Lowell Rd, Hudson NH 03051-4916 1 Tel: 1-88-VECTRON-1 Website: www.vectron.com
Rev: 06June05
SO-502 SAW Based Oscillator
Table 1. Electrical Performance
Parameter Symbol Minimum FN FSTAB 300 Typical Maximum 1350 +50, -250 +50, -100 12 5 3.3 55 12.6 5.25 3.450 70 Units MHz ppm ppm V V V mA dBm dBm dBm dBc ps,rms ps,rms V V ps % C mm Notes 1,2 1,2,7 5 2,3 2,3 2,3 2,3 2,3 2,3 2,3 2,3 5,6 5,6 2,3,4 2,3,4 2,3,4 2,3,4 1
Frequency
Center Frequency Frequency Stability (Referenced to FO) Aging (10 years)
Supply
Voltage (B) Voltage (C) Voltage (D) Current (No Load) VCC VCC VCC ICC PO PO PO 11.4 4.75 3.135
Output- Sinewave Options
Sinewave, into 50 (G) Sinewave, into 50 (J) Sinewave, into 50 (K) Harmonics Jitter @ 622.08 MHz (12 kHz to 20 MHz) Jitter @ 622.08 MHz (50 kHz to 80 MHz) 0 +7 +10 -20 0.28 0.29 VOL VOL tR,tF SYM TOP VCC-1.95 VCC-0.98 45 200 49/51 VCC-1.63 VCC-0.75 350 55
Output- PECL Logic Option (F)
Output Level Low Output Level High Rise & Fall Time Symmetry (Duty Cycle)
Operating Temperature Package Size
See Ordering Table 9.0 x 14.0 x 4.5
Table Notes: 1. See Standard Frequencies and Ordering Information 2. Parameters are tested with production test circuit 3. Parameters are tested at ambient temperature with test limits guard-banded for specified operating temperature. 4. Output levels are standard 100K PECL compatible and measured from 20% to 80% of a full output swing (Fig 1). 5. Not tested in production, guaranteed by design, verified at qualification. 6. Integrated across 12 kHz to 20 MHz or 50 kHz to 80 MHz per GR-253-CORE Issue3. 7. Maximum Frequency occurs at room temperature
Table 2. Typical Single Side-Band Phase Noise (dBc/Hz) for Sinewave Output
Output Frequency 622.08 MHz 1000 MHz 100 Hz Offset -70 -70 1 kHz Offset -100 -100 10 kHz Offset -125 -125 100 kHz Offset -155 -155 1 MHz Offset -160 -160
Vectron International, 267 Lowell Rd, Hudson NH 03051-4916 Tel: 1-88-VECTRON-1 Website: www.vectron.com
2 Rev: 06June05
SO-502 SAW Based Oscillator
tR
80% Vcc - 1.3V 20% Vcc - 1.6V
tF
SYM = 100 x tA / tB
Vcc - 1.0V
tA tB
Figure 1. 100K PECL Waveform
Outline Diagram
6 5 4
Pad Layout
VS-500-LFF-GNN SO-502-BJF-GNN XXX.XXX XXX.XXX VIVI YWW YYWW
1 2 3
8.890.15 [0.3500.006]
7.63 [0.300]
1.27 [0.050]
13.970.20 [0.5500.008] 0.460.05 [0.0180.002]
[
4.49+0.20 -0.30 +0.008 0.177-0.012
]
3.00 [0.118]
8.80 [0.346]
2.54 [0.100] 5.08 [0.200] mm [inch]
5.080.13 [0.2000.005]
2.540.13 [0.1000.005]
mm [inch]
Table 3. Pin Out - PECL Option
Pin
1 2 3 4 5 6
Symbol
OD GND Output COutput VCC
Function
N/C N/C or Output Disable Case and Electrical Ground Output Complementary Output Power Supply Voltage
1
Table Notes:
1. By setting Output Disable pin low, the RF output is disabled and pin 4 is held high, pin 5 is held low. The threshold for Output Disable is 1.4V above pin 3. Output disable pin can be left floating for normal operation
Vectron International, 267 Lowell Rd, Hudson NH 03051-4916 Tel: 1-88-VECTRON-1 Website: www.vectron.com
3 Rev: 06June05
SO-502 SAW Based Oscillator
Suggested Output Load Configurations - PECL Operation
+ 5.0V .0 1uF .1uF (From P LL) Vc OD G nd 1 2 3
6
+ 5.0V + 5.0V
V cc
120
120
5 C O utput O utput 4 82
(AC C ou pling)
82
+ 5.0V .0 1uF .1uF (From P LL) Vc OD G nd 1 2 3
6
V cc C O utput O utput (AC C ou pling)
5 4
330
330
Suggested Output Load Configurations - LVPECL Operation
+3.3V .01uF 0.1uF (From PLL) Vc OD Gnd 1 2 3
6
+3.3V +3.3V
Vcc
130
130
5 COutput Output 4 82
(AC Coupling)
82
+3.3V .01uF 0.1uF (From PLL) Vc OD Gnd 1 2 3
6
Vcc (AC Coupling)
5 COutput Output 4 240
240
Vectron International, 267 Lowell Rd, Hudson NH 03051-4916 Tel: 1-88-VECTRON-1 Website: www.vectron.com
4 Rev: 06June05
SO-502 SAW Based Oscillator
Table 4. Pin Out - Sinewave Option
Pin
1 2 3 4 5 6 Table Notes:
1. If Vcc1 is +12V and a separate 5V is not applied to pin 5 then pin 5 must be connected through a 220 1/4W external resistor.
Symbol
VC VEE Output VCC VCC
Function
N/C N/C Ground Sinewave Output 1 Vcc2 Vcc1
Suggested Output Load Configurations - SINEWAVE Operation
+12V Vcc NC 1 NC 2 3 6 5 4 220 1/4W
0.1uF
0.01uF
0.01uF Output AC Coupled with 50 to ground
+5V Vcc NC 1 NC 2 3 6 5 4 27 1/8 W
0.1uF
0.01uF
0.01uF Output AC Coupled with 50 to ground
Vectron International, 267 Lowell Rd, Hudson NH 03051-4916 Tel: 1-88-VECTRON-1 Website: www.vectron.com
5 Rev: 06June05
SO-502 SAW Based Oscillator
Tape and Reel (EIA-481-2-A)
Po F W
ODo W2 C N A
D
P1
W1
B
Tape Dimensions (mm)
Dimension
Tolerance SO-502
Reel Dimensions (mm)
F Do
Typ 1.5
W
Typ 24
Po
Typ 4
P1
Typ 12
A
Typ 330
B
Min 1.5
C
Typ 13
D
Min 20.2
N
Min 100
W1
Typ 24.4
W2
Max 30.4
Typ 11.5
# Per Reel
200
Absolute Maximum Ratings
Parameter Power Supply Storage Temperature Soldering Temp/Time Symbol VCC TS TLS Ratings VCC + 1.0V -55 to +125 +220/10 Unit V C C/sec
Stresses in excess of the absolute maximum ratings can permanently damage the device. Functional operation is not implied at these or any other conditions in excess of conditions represented in the operational sections of this datasheet. Exposure to absolute maximum ratings for extended periods may adversely affect device reliability.
Reliability
The SO-502 family is capable of meeting the following qualification tests:
Environmental Compliance
Parameter Mechanical Shock Mechanical Vibration Solderability Gross and Fine Leak Resistance to Solvents Conditions MIL-STD-883, Method 2002 MIL-STD-883, Method 2007 MIL-STD-883, Method 2003 MIL-STD-883, Method 1014 MIL-STD-883, Method 2016
Vectron International, 267 Lowell Rd, Hudson NH 03051-4916 Tel: 1-88-VECTRON-1 Website: www.vectron.com
6 Rev: 06June05
SO-502 SAW Based Oscillator
Handling Precautions
Although ESD protection circuitry has been designed into the SO-502 proper precautions should be taken when handling and mounting. VI employs a human body model and a charged-device model (CDM) for ESD susceptibility testing and design protection evaluation.
ESD Ratings
Model Human Body Model Charged Device Model Minimum 1500 V 1000 V Conditions MIL-STD 883, Method 3015 JESD 22-C101
Recommended Solder Reflow Profile
220
Temperature (Deg C)
183 150
60
60-90
45-60
Time (s)
VI qualification includes aging at various extreme temperatures, shock and vibration, temperature cycling, and IR reflow simulation. The conditions a device can withstand are well understood and devices can be subjected to the profile above. This profile shows a ramp up condition to prevent thermal shock, a preheat period in which the flux is activated, a ramp up to 183C which is the reflow temperature of Sn/Pb eutectic, and a gradual cool down. The time above 183C should not exceed 60 seconds and the peak temperature should be no more than 220C for 10 seconds. The SO-502's are hermetically sealed so an aqueous wash is not an issue.
Vectron International, 267 Lowell Rd, Hudson NH 03051-4916 Tel: 1-88-VECTRON-1 Website: www.vectron.com
7 Rev: 06June05
SO-502 SAW Based Oscillator
Available Standard Frequencies (MHz)
480 990 622.08 1000 640 1090 938 1200 970 1330 983.04
Other Frequencies Available Upon Request.
Ordering Information
SO - 502 - B J C - G N N - xxxx.xxxx
Product Family
SO: SAW XO
Frequency (See Above)
300 - 1350 MHz
Package
502: 9 x 14 x 4.5 mm
Input
D: 3.3 V C: 5.0 V B: 12.0 V
Other (Future Use)
N: N/A
Output
F: G: H: J: K: PECL Sine 0 dBm Sine 3 dBm Sine 7 dBm Sine 10 dBm
Other (Future Use)
N: N/A
Frequency Stability
L: 130 ppm (0C to +70 C only) T: 200 ppm
Operating Temperature
C: 0C to +70 C D: -20C to +85 C F: -40C to +85 C
For Additional Information, Please Contact:
USA: Vectron International, 267 Lowell Rd, Hudson, NH 03051 . . . . Tel: 1-88-VECTRON-1 EUROPE: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tel: +49 (0) 3328-4784-17 ASIA: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tel: +86-21-28909740 Fax: 1-888-FAX-VECTRON Fax: +49 (0) 3328-4784-30 Fax: +86-21-28909999
Vectron International reserves the right to make changes to the product(s) and or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.
Vectron International, 267 Lowell Rd, Hudson NH 03051-4916 Tel: 1-88-VECTRON-1 Website: www.vectron.com
8 Rev: 06June05

▲Up To Search▲

Price & Availability of SO-502-BHC-LNN1350

	To Download SO-502-BHC-LNN1350 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .