Part Number Hot Search : 
010LF BUV50 TS1102 BUW133A BADXCF A35BD BR301 P100M1
Product Description
Full Text Search
 

To Download CXA1101PM Datasheet File

  If you can't view the Datasheet, Please click here to try to view without PDF Reader .  
 
 


  Datasheet File OCR Text:
  ?1 cxa1100p, cxa1101p/m, cxa1102p/m, cxa1163p/m e90302a13-pp dolby * b type noise reduction system description cxa1100, cxa1101, cxa1102 and cxa1163 are ics including two separate dolby b type noise reduction processors. seven devices with four dolby levels and two types of package are provided for various applications. these devices feature very few external components, which is achieved by integrated filter circuits using integrated thin film capacitors with high capacitance. features minimum number of external components nr on/off and rec/pb switchs included small package (dip16, sop16) small supply current ( ~ 5.5ma, typ.) dual channel processors in one chip absolute maximum ratings (ta = 25?) supply voltage v cc 17 v operating temperature topr ?0 to +85 ? storage temperature tstg ?5 to +150 ? allowable power dissipation p d dip16 (a1100p/a1101p/a1102p/a1163p)900 mw sop16 (a1101m/a1102m/a1163m) 500 mw note 1) these ics are available only to the licensees of dolby laboratories licensing corporation from whom licensing and application information may be obtaind. note 2) "dolby" and double d symbols are trade marks of dolby laboratories licensing corporation. sony reserves the right to change products and specifications without prior notice. this information does not convey any license by any implication or otherwise under any patents or other right. application circuits shown, if any, are typical examples illustrating the operation of the devices. sony cannot assume responsibility for any problems arising out of the use of these circuits. 16 pin dip (plastic) 16 pin sop (plastic)
?2 cxa1100/cxa1101/cxa1102/cxa1163 pin description (ta = 25?, v cc = 12v (single supply), no signal) no. symbol z (in) vdc equivalent circuit description 2 v cc 12.0v power supply 1, 16 rec in 40k 6.0v recording (encode) input vcc gnd 40k vcc/2 1 16 3, 14 pb in 40k 6.0v playback (decode) input vcc gnd 40k vcc/2 14 3 5 on/off mode control pin for nr on/off "h" ? nr off "l" ? nr on vcc gnd 50 150 5 6, 11 line out 6.0v line (decode) output vcc gnd 150 150 6 11 4 v cc /2 1k 6.0v single supply ? v cc /2 split supply ? ground
?3 cxa1100/cxa1101/cxa1102/cxa1163 no. symbol z (in) vdc equivalent circuit description 7, 10 tc 0.3v time constant pin for the level detector vcc gnd 4 8.2k 100k 7 10 8, 9 rec out 6.0v recording (encode) output vcc gnd 300 8.2k 300 8 9 12 rec/pb mode control pin for rec/pb (encode/decode) "h" ? b (decode) "l ? ec (encode) vcc gnd 50 150 12 13 iref 1.2v reference current input pin for the active filters 15 gnd 0v single supply ? ground split supply ? v ee vcc gnd 10 1.2v 13
?4 cxa1100/cxa1101/cxa1102/cxa1163 block diagram test circuit c21 1 c22 1 c24 4.7 line out c23 0.68 c14 4.7 line out c13 0.68 r1 43k c12 1 c11 1 pb in pb in rec in c1 100 rec in 4 5 7 12 2 13 att2 att3 att3 sc det att2 att3 att1 sc det 6 3 1 att2 att3 att1 sc det 9 10 11 14 15 16 8 vcc on/off rec out c25 4.7 att: attenuator sc : side chain det: detector c15 4.7 rec out rec/pb r p r21 5.1k off s4 c21 1 r22 5.1k c2 100 c22 1 c1 100 r5 510 s2 p r s1 c24 4.7 p r s5-2 c23 0.68 r p r11 5.1k off s3 c11 1 r12 5.1k c12 1 r1 43k c14 4.7 p r s5-1 c13 0.68 3 4 5 6 7 8 9 10 11 12 14 15 1 2 13 16 r3 12k audio sg a vcc +15v 1 2 s6-2 r2 10k dc level meter c25 4.7 1 2 s6-1 ccir/arm filter off on s7 ac level meter distortion analyzer on off r4 2k c16 4.7
?5 cxa1100/cxa1101/cxa1102/cxa1163 electrical characteristics ta = 25?, dolby level: ?0dbm ( = 245mvrms) at rec out v cc = 15v (cxa1100), v cc = 12v (cxa1101), v cc = 9v (cxa1102) v cc = 6v (cxa1163) item symbol r/p nr f (hz) other conditions test condition * min. typ. max. unit operating voltage cxa1100 cxa1101 cxa1102 cxa1163 supply current cxa1100 cxa1101 cxa1102 cxa1163 line out level cxa1100 cxa1101 cxa1102 cxa1163 rec in level pb in level encode characteristics (boost) (1) (2) (3) (4) (5) signal handling cxa1100 cxa1101 cxa1102 cxa1163 vopr i cc vlout vrin vpin b-r-1 b-r-2 b-r-3 b-r-4 b-r-5 vomax r r r p r r r r r r off off off off on on on on on off 1k 1k 1k 500 2k 5k 10k 10k 1k signal handling 3 12db no signal ?5db ?5db ?5db ?0db 0db thd = 1% 11.5 8.5 6.5 5.0 3.5 3.5 3.5 3.5 ?.0 ?.0 ?.0 ?1.0 ?2 ?2 1.4 5.5 3.9 9.7 ?.1 13.5 14.0 14.0 13.0 5.6 5.5 5.3 5.1 0.0 ?.0 ?.0 ?0.0 ?0 ?0 2.9 7.0 5.4 10.4 0.4 15.3 15.9 15.9 15.0 16.0 16.0 16.0 16.0 7.5 7.5 7.5 7.5 1.0 ?.0 ?.0 ?.0 ?8 ?8 4.4 8.5 6.9 11.9 1.9 v v v v ma ma ma ma dbm dbm dbm dbm dbm dbm db db db db db db db db db 0dbm = 0.775vrms
?6 cxa1100/cxa1101/cxa1102/cxa1163 item symbol r/p nr f (hz) other conditions test condition * min. typ. max. unit total harmonic distortion 1) nr off cxa1100 cxa1101 cxa1102 cxa1163 2) nr on cxa1100 cxa1101 cxa1102 cxa1163 input impedance rec in pb in encode s/n ratio crosstalk rec-pb pb-rec rec ch to ch pb ch to ch rec out offset voltage (nr on ?off) control voltage "h" level "l" level thd (off) thd (on) zrec zpb sn (ccir) ct-1 ct-2 ct-3 ct-4 voff vc-h vc-l r r r p r r p r off on on off off off off on 1k 1k 1k 1k 1k 1k 1k 1k +10db +10db rg = 5k (ccir/arm) 0db 0db 0db 0db 28 28 65 ?0 2.5 0 0.03 0.04 0.05 0.06 0.03 0.04 0.06 0.09 40 40 69 ?2 ?1 ?0 ?0 0 0.2 0.2 0.2 0.2 0.3 0.3 0.3 0.3 57 57 ?5 ?0 ?0 ?0 40 v cc 0.5 % % % % % % % % k k db db db db db mv v v * 0db means the level which provides the dolby level at the recording output in the noise reduction off mode.
?7 cxa1100/cxa1101/cxa1102/cxa1163 example of representative characteristics 4.4 4.8 5.2 5.6 6.0 6.4 6.8 ?2 ? ? 0 4 8 12 input level [db] icc ?supply current [ma] supply current vs. input voltage (cxa1101) nr on 1khz encode mode 0db = dolby level nr off 1khz, 10khz nr on 10khz 0 2 4 6 8 10 12 200 500 1k 2k 5k 10k 20k frequency [hz] encode boost [db] encode characteristics ?0db ?0db ?0db ?0db ?0db 0db v cc = 12v 0 2 4 6 8 10 12 200 500 1k 2k 5k 10k 20k frequency [hz] encode boost [db] temperature characteristics ?0db ?0db ?0db ?0db 0db v cc = 12v ta = ?5? ta = 25? ta = 75? 3.6 4.0 4.4 4.8 5.2 5.6 6.0 4 6 8 10 121416 vcc ?supply voltage [v] icc ?quiescent current [ma] nr on nr off quiescent current vs. supply voltage 8 10 12 14 16 18 20 4 6 8 10 121416 vcc ?supply voltage [v] signal handling [db] signal handling encode mode nr off f = 1khz thd = 1% a1163 a1102 a1101 a1100 2 4 6 8 10 12 14 123 456 7 r l ?load resistance [k w ] maximum output level [dbm] load characteristics (cxa1101) 0 encode mode v cc = 12v thd = 1% line out rec out
?8 cxa1100/cxa1101/cxa1102/cxa1163 nr o ff to t al harrmo nic dist o rt io n-1 (cx a1101) output level [db] total harmonic disttortion [%] ? 0.01 0.02 0.05 0.1 0.2 0.5 1.0 16 ? 0 4 8 12 encode mode v cc = 12v 0db = dolby level f = 100hz f = 1khz f = 10khz ? 0.01 0.02 0.05 0.1 0.2 0.5 1.0 16 ? 0 4 8 12 encode mode 0db = dolby level f = 1khz v cc = 15v v cc = 12v v cc = 8.5v ? 0.01 0.02 0.05 0.1 0.2 0.5 1.0 16 ? 0 4 8 12 encode mode 0db = dolby level f = 1khz v cc = 15v v cc = 12v v cc = 8.5v ? 0.01 0.02 0.05 0.1 0.2 0.5 1.0 16 ? 0 4 8 12 encode mode 0db = dolby level f = 1khz v cc = 15v v cc = 11.5v ? 0.01 0.02 0.05 0.1 0.2 0.5 1.0 16 ? 0 4 8 12 encode mode 0db = dolby level f = 1khz v cc = 15v v cc = 11.5v ? 0.01 0.02 0.05 0.1 0.2 0.5 1.0 16 ? 0 4 8 12 encode mode v cc = 12v 0db = dolby level f = 100hz f = 1khz f = 10khz nr o nto t al harrmo nic dist o rt io n-1 (cx a1101) nr o ff to t al harrmo nic dist o rt io n-2 (cx a1100) nr o nto t al harrmo nic dist o rt io n-2 (cx a1100) nr o nto t al harrmo nic dist o rt io n-3 (cx a1101) nr o ff to t al harrmo nic dist o rt io n-3 (cx a1101) total harmonic disttortion [%] total harmonic disttortion [%] total harmonic disttortion [%] total harmonic disttortion [%] total harmonic disttortion [%] output level [db] output level [db] output level [db] output level [db] output level [db]
?9 cxa1100/cxa1101/cxa1102/cxa1163 nr o ff to t al harmo nic dist o rt io n-4 (cx a1102) output level [db] total harmonic distortion [%] 20 0.01 0.02 0.05 0.1 0.2 0.5 1.0 16 ? 0 4 8 12 encode mode 0db = dolby level f = 1khz v cc = 15v v cc = 9v v cc = 6.5v 20 0.01 0.02 0.05 0.1 0.2 0.5 1.0 16 ? 0 4 8 12 encode mode 0db = dolby level f = 1khz v cc = 15v v cc = 9v v cc = 6.5v 24 0.01 0.02 0.05 0.1 0.2 0.5 1.0 20 04 81216 encode mode 0db = dolby level f = 1khz v cc = 15v v cc = 6v v cc = 5v 24 0.01 0.02 0.05 0.1 0.2 0.5 1.0 20 0 4 8 12 16 encode mode 0db = dolby level f = 1khz v cc = 15v v cc = 6v v cc = 5v channe l t o channe l crosst alk (cx a1101) frequency [hz] crosstalk [db] 10k ?0 v cc = 12v/6v nr off c1 (pin4) = 100 f 5k 2k 1k 500 200 100 ?0 ?0 ?0 ?0 ?0 ?0 single supply split supply encode decode rec t o pb and pb t o rec crosst alk (cx a1101) 10k ?0 v cc = 12v/6v nr off c1 (pin4) = 100 f 5k 2k 1k 500 200 100 ?0 ?0 ?0 ?0 ?0 ?0 single supply split supply nr o n to t al harmo nic dist o rt io n-4 (cx a1102) nr o ff to t al harmo nic dist o rt io n-5 (cx a1163) nr o n to t al harmo nic dist o rt io n-5 (cx a1163) total harmonic distortion [%] total harmonic distortion [%] total harmonic distortion [%] output level [db] output level [db] output level [db] crosstalk [db] frequency [hz]
?10 cxa1100/cxa1101/cxa1102/cxa1163 ripple rejection ratio-2 (cxa1101) frequency [hz] ripple rejection ratio [db] 10k ?0 5k 2k 1k 500 200 100 ?0 ?0 ?0 ?0 ?0 ?0 decode mode v cc = 12v single supply c1 (pin4) = 100f c1 (pin4) = 470f nr on nr off ripple rejection ratio-4 (cxa1101) frequency [hz] ripple rejection ratio [db] 10k ?0 5k 2k 1k 500 200 100 0 ?0 ?0 ?0 ?0 ?0 v ee rejection v cc, v ee = 6v encode decode nr off nr on ripple rejection ratio-1 (cxa1101) frequency [hz] ripple rejection ratio [db] 10k ?0 encode mode v cc = 12v single supply 5k 2k 1k 500 200 100 ?0 ?0 ?0 ?0 ?0 ?0 c1 (pin4) = 100f c1 (pin4) = 470f nr on nr off ripple rejection ratio-3 (cxa1101) frequency [hz] ripple rejection ratio [db] 10k ?0 v cc rejection v cc, v ee = 6v 5k 2k 1k 500 200 100 ?0 ?0 ?0 ?0 ?0 ?0 encode decode nr off nr on notes on applications 1) power supply the cxa1100 series is basically designed to operate on single ended supply. the split supply operation is also possible, however, v ee (negative) supply should provide low noise and ripple characteristics. the ripple rejection ratio of these devices is generally good for vcc supply (single ended supply and split supply), however, that for v ee supply is not so good in the nr on mode because the integrated capacitors for the side chain filter are connected to pin 15 (v ee on split supply).
?11 cxa1100/cxa1101/cxa1102/cxa1163 when the ripple or noise component of v ee supply is not negligible small, the cr filter shown in fig. a-1 will be usefull. the operation voltage range are cxa1100 11.5 to 16v (5.75 to 8v) cxa1101 8.5 to 16v (4.25 to 8v) cxa1102 6.5 to 16v (3.25 to 8v) cxa1163 5.0 to 16v (2.5 to 8v) fig. a-1. the devices will satisfy the signal handling of 12db specified by dolby laboratories on above voltage range. 2) operation mode control the cxa1100 series provide fully electronic switching circuits. the functions are controlled by dc voltages of the two control pins of rec/pb (pin 12) and on/off (pin 5). the switching truth tables are shown in fig. a-2. v h and v l are defined as (a) single ended supply operation v cc 3 v h 3 2.5v 0.5v 3 v l 3 0v (b) split supply operation v cc 3 v h 3 v ee + 2.5v v ee + 0.5v 3 v l 3 v ee fig. a-2. it is desirable to provide cr time constant circuits at the mode control pins with time constant from 100msec to 1sec, which will reduce switching clicks effectively. 3) reference levels characteristics and specifications of the dolby noise reduction processor are defined as the levels and measured with reference to the dolby level. this particular level in these devices is ?0dbm (245mvrms), and is measured at the recording output (rec out) in the nr off mode. the reference levels of the recording input (rec in), play back input (pb in) and line output (line out) are defined the levels which provide the dolby level at the recording output in the nr off mode. the cxa1100 series has a common silicon die, and has different internal connection. the series provides four different line output levels for various applications. other reference levels, recording input level, playback input level and recording output level (= dolby level) are identical in all devices. the reference levels are as follows recording output level (= dolby level) ?0dbm (245mvrms) recording input level ?0dbm (24.5mvrms) play back input level ?0dbm (24.5mvrms) line output level cxa1100 0dbm (775mvrms) cxa1101 ?dbm (548mvrms) cxa1102 ?dbm (388mvrms) cxa1163 ?0dbm (245mvrms) 13 14 15 r1 43k 47 100 to 470f v ee cxa1100 series rec/pb function v h pb (decode) v l rec (encode) on/off function v h nr off v l nr on
?12 cxa1100/cxa1101/cxa1102/cxa1163 4) mpx filter termination and c 1 for vcc/2 (pin 4) the mpx (multiplex) filter termination method shown in fig. a-3 allows saving the coupling capacitors between the buffer amplifiers and mpx filters. however, the channel to channel separation and rec to pb crosstalk of low frequency signals will be degraded by the termination resistor rt. for example, 5k of r 1 will degrade the channel to channel separation to 50db. better separation can be obtained by increasing the capacitance of c 1 (pin 4) to 220f or 470f. the allowable minimum value of c 1 is 47f, and 100f is the standard recommended value. larger values of c 1 are generally desirable in order to improve the crosstalk and ripple rejection ratio. 5) application for dubbing cassette decks the cxa1100 series generates non decoded signal at the recoding output in the decode mode, and can simplify the structure of dubbing decks. see the sony' dolby b/c type ic (cx20187/cxa1097q or cx20188/cxa1098q) data sheet in detail. fig. a-3. switchable processor with single supply note 1) resistor and capacitor tolerances are 10% and 20% respectively unless otherwise specified. note 2) when resistors rt are connected to pin 4 for the mpx filter termination, increase the capacitances of c 1 and c 11 (c 21 ) to 470f and 4.7f respectively. 2 3 13 14 15 4 1 16 c1 470 r t r t mpx filter mpx filter mpx filter buffer mpx filter mpx filter mpx filter buffer c11 4.7 c21 4.7 line input line input cxa1100 series 3 4 5 6 7 8 10 11 12 14 15 1 c21 1 c22 1 nr on/off on off c24 4.7 line out c23 (10%) 0.68 c14 4.7 line out c13 (10%) 0.68 r1 (12 %) 43k c3 10 c12 1 c11 1 pb in (?0dbm) pb in (?0dbm) rec in (?0dbm) v cc 2 c2 100 c1 100 rec/pb r2 10k 13 rec pb 16 rec in (?0dbm) c25 4.7 rec out (?0dbm) c15 4.7 rec out * r t * r t 9 * *
?13 cxa1100/cxa1101/cxa1102/cxa1163 switchable processor with split supply playback processor with aux input 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 c21 1 c22 1 nr on/off on off c25 4.7 c24 4.7 rec out (?0dbm) line out c23 (10%) 0.68 c15 4.7 c14 4.7 rec out (?0dbm) line out c13 (10%) 0.68 r1 (12 %) 43k c3 10 rec/pb pb rec r2 10k c12 1 c1 100 c11 1 c2 100 pb in (?0dbm) rec in (?0dbm) v ee pb in (?0dbm) rec in (?0dbm) v cc 3 4 5 6 7 8 9 10 11 12 14 15 1 c21 1 c22 1 nr on/off on off c24 4.7 line out c13 (10%) 0.68 c14 4.7 line out c13 (10%) 0.68 r1 (2%) 43k c3 10 c12 1 c11 1 tape in (?0dbm) tape in (?0dbm) aux in (?0dbm) v cc 2 c2 100 c1 100 tape/aux * r2 10k 13 aux tape 16 aux in (?0dbm) * * * * note 1) resistor and capacitor tolerances are 10% and 20% respectively unless otherwise specified. note 2) when aux inputs are not necessary, reject r 2 , c 3 , c 11 , c 21 and tape/aux switch, and connect pin 12 to vcc. note 1) resistor and capacitor tolerances are 10% and 20% respectively unless otherwise specified.
?14 cxa1100/cxa1101/cxa1102/cxa1163 package outline unit: mm cxa1101p, cxa1101p cxa1102p, cxa1163p cxa1101m, cxa1102m cxa1163m cxa1100p, cxa1101p cxa1102p package structure package material lead treatment lead material package weight epoxy resin solder plating copper 19.2 ?0.1 + 0.4 9 18 2.54 0.5 0.1 1.2 0.15 3.0 min 0.5 min 3.7 ?0.1 + 0.4 6.4 ?0.1 + 0.3 7.62 0.25 ?0.05 + 0.1 0?to 15 16 16pin dip (plastic) 300mil 1.0 g sony code eiaj code jedec code dip-16p-01 * dip016-p-0300-a similar to mo-001-ae sony code eiaj code jedec code package structure package material lead treatment lead material package weight epoxy resin solder plating copper / 42 alloy 16pin dip (plastic) 300mil 19.1 ?0.1 + 0.4 2.54 8 1 9 16 6.4 ?0.1 + 0.3 0.25 ?0.05 + 0.1 7.62 0?to 15 3.7 ?0.1 + 0.4 0.5 min 3.0 min 0.46 0.1 1.53 0.15 dip-16p-03 * dip016-p-0300-b similar to mo-001-ae 1.0g package structure package material lead treatment lead material package weight sony code eiaj code jedec code sop-16p-l01 * sop016-p-0300-a copper alloy solder plating epoxy resin 16pin sop (plastic) 300mil 9.9 ?0.1 + 0.4 16 9 18 1.27 0.45 0.1 5.3 ?0.1 + 0.3 7.9 0.4 6.9 1.85 ?0.15 + 0.4 0.5 0.2 0.2 ?0.05 + 0.1 0.1 ?0.05 + 0.2 0.2g 0.15 m 0.12 sony code eiaj code jedec code package structure package material lead treatment lead material package weight epoxy resin solder plating copper dip-16p-191 dip016-p-0300-au ms-001-aa 16pin dip (plastic) 300mil 0?to 10 0.28 ?0.06 6.35 0.127 7.62 1 8 9 16 19.35 0.5 2.54 0.254 0.457 0.076 1.016 3.1 min 0.508 min 5.08 max + 0.1 1.0g
?15 cxa1100/cxa1101/cxa1102/cxa1163 cxa1100p, cxa1101p/m, cxa1102p/m, cxa1163p/m sony code eiaj code jedec code package structure package material lead treatment lead material package weight epoxy resin solder plating copper 0.15 m 0.13 16 1 9 8 * 10.2 ?0.1 + 0.3 0.71 0.1 1.27 0.1 0.4 0.1 * 5.3 ?0.1 + 0.3 7.8 0.1 0.75 0.2 4?to 8 2.0 max 0.05 min 1.8 0.15 0.05 sop-16p-l122 sop016-p-0300-bx 16pin sop (plastic) 300mil 0.21g note: dimension * ?does not include mold protrusion.


▲Up To Search▲   

 
Price & Availability of CXA1101PM

All Rights Reserved © IC-ON-LINE 2003 - 2022  

[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy]
Mirror Sites :  [www.datasheet.hk]   [www.maxim4u.com]  [www.ic-on-line.cn] [www.ic-on-line.com] [www.ic-on-line.net] [www.alldatasheet.com.cn] [www.gdcy.com]  [www.gdcy.net]


 . . . . .
  We use cookies to deliver the best possible web experience and assist with our advertising efforts. By continuing to use this site, you consent to the use of cookies. For more information on cookies, please take a look at our Privacy Policy. X