package dimensions + e+ d 2 0.129 (3.3) 0.119 (3.0) 0.433 (11.0) 0.422 (10.7) 0.315 (8.0) 0.295 (7.5) 0.272 (6.9) 0.055 (1.40) 0.045 (1.14) 0.110 (2.8) 0.091 (2.3) 0.055 (1.40) 0.045 (1.14) 1 3 5 4 0.020 (0.51) (sq) 0.472 (12.0) 0.457 (11.6) 0.249 (6.35) 0.243 (6.15) 0.39 (1.00) 0.34 (0.85) 0.103 (2.60) nom optical c l l c c l c l pin 1 anode pin 2 cathode pin 3 v pin 4 v pin 5 gnd cc o notes: 1. dimensions for all drawings are in inches (millimeters). 2. tolerance of .010 (.25) on all non-nominal dimensions unless otherwise specified. 3. lead cross section is controlled between .050 (1.27) from the seating plane and the end of the leads. notes (applies to max ratings and characteristics tables.) 1. derate power dissipation linearly 1.67 mw/c above 25c. 2. derate power dissipation linearly 2.50 mw/c above 25c. 3. rma flux is recommended. 4. methanol or isopropyl alcohols are recommended as cleaning agents. 5. soldering iron 1/16? (1.6mm) from housing. 6. as long as leads are not under any stress or spring tension. features black plastic housing choice of inverter or buffer output functions choice of open-collector or totem-pole output configuration no contact switching ttl/cmos compatible output functions 1 of 4 100011b h22l series optologic ? optical interrupter switch h22ltb totem-pole, buffer output h22lti totem-pole, inverter output h22lob open-collector, buffer output H22LOI open-collector, inverter output part number definitions parameter symbol rating units operating temperature t opr -40 to +85 c storage temperature t stg -40 to +85 c soldering temperature (iron) (3,4,5,6) t sol-i 240 for 5 sec c soldering temperature (flow) (3,4,6) t sol-f 260 for 10 sec c emitter continuous forward current i f 50 ma reverse voltage v r 5v power dissipation (1) p d 100 mw sensor output current i o 50 ma supply voltage v cc 4.0 to 16 v output voltage v o 30 v power dissipation (1) p d 150 mw absolute maximum ratings (t a = 25c unless otherwise specified)
2 of 4 100011b parameter test conditions symbol min. typ. max. units operating supply voltage v cc v cc 4.5 16 v input diode forward voltage i f = 20 ma v f ? 1.7 v reverse leakage current v r = 5 v i r ?10 a coupled operating supply current i f = 15 ma or 0 ma, v cc = 16 v i cc ?5ma low level output voltage i f = 0 ma, v cc = 5 v, r l = 100 ! v ol ? 0.4 v h22ltb, h22lob low level output voltage i f = 15 ma, v cc = 5 v, r l = 360 ! v ol ? 0.4 v h22lti, H22LOI high level output voltage i f = 15 ma, v cc = 5 v, i oh = -800 av oh 2.4 ? v h22ltb high level output voltage i f = 0 ma, v cc = 5 v, i oh = -800 av oh 2.4 ? v h22lti high level output current i f = 0 ma, v cc = 5 v, i oh = -800 ai oh 100 a h22lob high level output current i f = 0 ma, v cc = 5 v, v oh = 30 v i oh ? 100 a H22LOI turn on threshold current v cc = 5 v, r l = 360 ! i f (+) ? 15 ma turn off threshold current v cc = 5 v, r l = 360 ! i f (-) 0.50 ? ma hysteresis ratio i f (+) / i f (-) 1.3 propagation delay v cc = 5 v, r l = 360 ! t plh, t phl 5 s output rise and fall time v cc = 5 v, r l = 360 ! t r, t f 70 ns electrical / optical characteristics (t a =25c) h22l series optologic ? optical interrupter switch part led output number h22ltb on high h22ltb off low h22lti on low h22lti off high h22lob on high h22lob off low H22LOI on low H22LOI off high input/output table
3 of 4 100011b open-collector output buffer h22lob cathode (2) gnd (5) regulator voltage vcc (3) vout (4) la anode (1) anode (1) cathode (2) la regulator voltage gnd (5) vout (4) vcc (3) anode (1) cathode (2) la regulator voltage gnd (5) vout (4) vcc (3) anode (1) cathode (2) regulator voltage la vcc (3) vout (4) gnd (5) open-collector output inverter H22LOI totem-poleoutput inverter h22lti totem-pole output buffer h22ltb circuit schematics h22l series optologic ? optical interrupter switch
4 of 4 100011b c 2 r 2 r 1 1 c .1 uf bypass 5v gnd pulse generator v = 5v f = 10 khz d.c. = 50% o 1 r = 180 ! ! r = 360 2 1 c = 15 pf c = 20 pf 2 stray wire capacitance c and c include probe and 12 switching speed test circuit plh r t phl t 50% 90% 10% oh v ol v 10% 90% 50% output v o t f t 0 ma oh phl 0 ma t v plh 50% t 10% 90% 90% 10% r t f t output o v ol v + - v in r in .1 uf bypass l r v cc gnd o v typical operating circuit switching test curve for buffers switching test curve for inverters h22l series optologic ? optical interrupter switch
|