specifications dimensions t 1 in case of some problems for measured values, measure after applying rated voltage for 120 minutes at 105 c . (unit : mm) size list 30 rv : rated voltage (sv) : surge (room temperature) 4 q f d j g j d b u j p o t g p s f b d i t f s j f t 4 . specifications for each series d l f 15min. 19min. d this is an even lower esr series based on our sep series. suitable for use with motherboards, servers, vga, etc. lead free-flow is supported. marking : polarity( ), rated voltage, rated capacitance (purple) sanyo, os-con , lot.no. sepc. 4min. t for the minimum packing quantity, please refer to page 51. e9 e12 e13 f13 d+0.5max. 8.0 8.0 8.0 10.0 lmax. f 9.0 12.0 13.0 13.0 d 0.05 0.6 0.6 0.6 0.6 3.5 0.5 3.5 0.5 3.5 0.5 5.0 0.5 size code conductive polymer type sepc series large capacitance, low esr rv sv f 2.5 3.3 4.0 5.2 6.3 8.2 16.0 18.4 270 470 560 680 820 1500 2700 e9 e9 | e13 f13 e9 | e13 e13 f13 e9 | e13 f13 f13 e12 f13 d l 15min. 4min. 19min. d f e12.e13.f13 size e9 size e9 size flat rubber is used. items characteristics -55 c to +105 c m : 20% less than or equal to the value of table3 less than or equal to the value of table3 less than or equal to the value of table3 within 20% 1.5 times or less than an initial standard 1.5 times or less than an initial standard below an initial standard within 20% 1.5 times or less than an initial standard 1.5 times or less than an initial standard below an initial standard (after voltage processing) within 5% below an initial standard below an initial standard below an initial standard (after voltage processing) category temperature range tolerance on rated capacitance tangent of loss angle leakage current esr endurance damp heat (steady state) characteristics of impedance ratio at high temp. and low temp. -55 c +105 c ? c/c tan esr leakage current ? c/c tan esr leakage current ? c/c tan esr leakage current resistance to soldering heat z / z 20 c z / z 20 c 0.75 to 1.25 0.75 to 1.25 120hz 120hz 105 c, 2,000h, rated voltage applied 60 c, 90% rh, 1,000h, no-applied voltage flow method (260 5 c x 10s) t 1 conditions based the value at 100khz | +20 c after 2 minutes
31 table3 sepc series characteristics list t capacitance tolerance : m 20% t after 2 minutes 6sepc470mx 4sepc560mx 2sepc560mx 2sepc820mx 16sepc270m 6sepc470m 4sepc560m 4sepc680m 2r5sepc820m 16sepc470m 6sepc680m 6sepc1500m 4sepc820m 2sepc2700m 6.3 4 2.5 2.5 16 6.3 4 4 2.5 16 6.3 6.3 4 2.5 470 560 560 820 270 470 560 680 820 470 680 1500 820 2700 8 7 8 7 11 8 7 7 7 10 7 10 7 10 5700 6100 4700 6100 5000 5700 6100 6100 6100 6100 6640 5560 6640 5560 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 592 500 280 500 864 592 500 544 500 1504 857 1890 656 1350 size code part number t 1 rated ripple current 100khz (marms) at 105 c tangent of loss angle (max.) leakage current ( a) (max.) t 2 rated voltage (v) rated capacitance ( f) 4 q f d j g j d b u j p o t g p s f b d i t f s j f t 4 . specifications for each series esr 100khz to 300khz (m ? ) (max.) frequency coefficient for ripple current frequency coefficient 120hz ? f ? 1khz 0.05 1khz ? f ? 10khz 0.3 10khz ? f ? 100khz 0.7 100khz ? f ? 500khz 1 e9 e12 e13 f13
|
